GR310MB User Munal draft
Contents
1. Picture 3 use a PE pipe one side connect with the overflow outlet and another side with a sink or container Note The connection with a overflow discharge is a safety measurement for the machine Usually there is no overflow water out But if you found there is please contact with service people to deal with correspondingly 6 Operation 6 1 Attentions before using e Check the connectors of water supply and valves to make sure these connects seal well Check if the heating switch is in switch off position if not please turn it off When the 9 18 heating switch is on and there no water in hot tank the heating element will be burnt Check if the cooling switch is in switch off position if not please turn it off Check if the socket this machine use is well grounded make sure the socket is work properly Note this machine has high power heating system it must use three holes socket that can load at least 10A current 6 2 Connect to Water and Electricity Supply Open the three way ball valve machine connect with water supply Put the plug of machine into a three pin socket machine connects with electricity supply 7 Different Functional Systems 7 1 Filtration System 7 1 1 ACF Filtration system UF Filtration System After connected with electricity supply all the icons on the display panel shin for one second the indicator light see outlook instruction become blue the machine enter working mode Ma2. UV icon is ili In the machine that has UV system inside the UV icon is instead of Ozone Icon This clause only applies machine with UV system inside 8 Common Operation 8 1 Get Hot Water 8 1 1 Get One Cup of Hot Water water button EM the indicator light on the faucet becomes red then push getting 200ml hot water During getting one cup of hot water the heating icon shins if you want less than 200ml push water button or other buttons to Stop 8 1 2 Get hot water in different quantity tai pir shin on a frequency of 2 Hz push water button 11 18 getting hot water if doesn t push any buttons 1 minutes later machine stop hot water outlet automatically Note This clause only applies to the machine with heating system 8 2 Get Cold Water 8 2 1 Get One Cup of Cold Water Push water buttonl amp S M to get 200ml cold water During getting one cup of cold water the cooling icon shins if you want less than 200ml push water button or other buttons to Stop 8 2 2 Get hot water in different quantity Push water button for 3 seconds to get cold water at the same time the cooling icon shin on a frequency of 2 Hz push water button or any other button to stop getting hot water if doesn t push any buttons 1 minutes later machine stop cold water outlet automatically 8 3 Get Mixed Water Push the extra hot button then push the water button for 3 seconds to get 200ml mixed
3. cooling switch at the back of machine the cooling icon lights on And the cooling system is working when the cooling icon lights off the cooling process finishes 10 18 7 4 Note This clause only applies to the machine with cooling system Sterilization System 7 4 1 Ozone System Forced sterilization After filling water process is finished push ozone switch at the back of machine machine entering sterilizing mode The ozone icon lights on 3 minutes later the process stopping and the zone icon will shin for 10minutes then light off During the sterilizing process you can push ozone button again to stop the process Note During the sterilizing process including the 10 minutes of zone icon shinning you can not get water Auto sterilization Every time when the machine enters energy saving mode machine also automatically enter auto sterilization mode the ozone works 20 seconds then the process stops And 12 hours later machine will auto sterilize for 20 seconds During the auto sterilization process you can push the ozone button to stop the process Note This clause only applies to the machine with ozone system 7 4 2 UV System When getting cold water the UV system automatically work The UV icon lights on after getting cold water the UV system still works for 1 minute then stop the UV icon lights off When there is no cold water consumption for 4 hours the UV system automatically work for 1 minute Note The
4. hot water No cold water Smell in the water Electricity leakage Display or push buttons are no reaction ehaven t connect to power supply ePower socket failure eWater inlet valve shut off ewater pipe is blocked or the water pressure is too low eDidn t turn on the heating system eConsumption of hot water is too much eThermostat on the hot tank shut off eDidn t turn on the cooling system eConsumption of cold water is too much eDid not get cold water for a long time there are ice in the cold tank Didn t turn on the cooling system eConsumption of cold water is too much eDidn t get cold water for a long time there are ice in the cold tank eDrip tray is full e Water leakage inside of the machine eNew machine eMachine is not used for a long time eFilters are out of date eMachine is not earthed well ePower cord damage eHardware failure eSystem crashes eCheck if machine has connected to power supply eCheck if the power socket is working properly eCheck if the inlet valve is open eCheck the water supply eTurn on heating switch eCheck it 10 minutes later ePress thermostat again to reset eTurn on cooling switch eCheck it 30 minutes later eTurn off the power supply start the machine again after 2 hours eEmpty the drip tray eShut off the power supply and water supply then contact with our service staff eGet and drain 10 15L water eGet and drain 10 15L water eContact with our ser
5. water 8 4 Extra Hot Function Push extra hot button for 3 seconds the extra heating process is activated the extra heating icon lights on When the hot water temperature reaches 98 degree centigrade the extra heating process finish the extra heating icon lights off You can get hot water as clause 8 1 explained 9 Maintenance and replacement 9 1 Filter Replacement 9 1 1 Replace Period 12 18 ACF Filter Change every 6 month Compound Filter change every 6 to 12 month Note the replacement period recommended in the above table is for general water condition it is just for reference only The actual change period will be different according to different water condition 9 1 2 Taking Off and Install of Decorative Panel Take off decorative panel Use your finger to hook Notch and then pull up decorative panel Install of decorative panel Insert the front buckle of decorative panel into the front panel then press the decorative panel For the Machine with UV Only i ACF Filter Hot Tank C r UF Filter RO Filter Remark The machine with UV can only has one filter inside Picture 4 9 1 3 How to replace filter After remove the decorative panel you will see there are one or two filter in machine Turn the filter handle counterclockwise to take off filter And put the filter into filter base and turn filter handle clockwise to install filter 13 18 Picture 5 Open Turn the filter out Count
6. NN NN please check which option your machine belongs to 3 18 2 Brief Instruction Of Machine 2 1 Outlook Instruction 1 Control Panel 10 Cooling Switch 2 Indicator Light 11 Heating Switch 3 Water Outlet 12 Maintenance cover 4 Front Panel 13 Vent 5 Drip Tray Cover 14 Water Inlet Connector 6 Side Panel 15 Waste Water Drain Connector RO version 7 Drip Tray 16 Overflow Outlet 8 Decorative Panel 17 Power Cord 9 O3 Switch 18 Fuseholder 4 18 2 2 Control Panel Instruction 6 8 1 U esee Child Lock 2 WB zoe Water Button Cold Water Button 3 ME 2e Extra Hot Button 4 de ngi Cooling Icon Ds E Extra Heating Icon 6 c veces Water Making Icon 7 50a Ozone Icon 8 A T Heating Icon 5 18 3 Technical Parameter tems Specification Rated Voltage 220 V AC Electrical Rated Frequency 50 Hz Performance Rated General Power 1000 W Rated General Current 5 8A Hot Tank Volume Heating System Heating Power Heating Capacity Hot Water Temp Cold Tank Volume Cooling System Cooling Power Rated Cooling Current Cooling Capacity Cold Water Temp Pre Filter O 5 1 micron ACF Filter 0 5 micron Filtration System UF Filter 0 5 micron ROFilter 50G Ozone System 0 5 micron 1 The machine have different options please check Functional module configuration table Water Pressure 14 Kgs 17kgs No Note 2 You may not be informed should t
7. User Manual Table Top Mini Bar Water Dispenser i H na I D GR310MB Please read this manual carefully before using 1 18 Content 1 Functional module configuration table 2 Brief Instruction of Machine 2 1 Outlook Instruction 2 2 Control Panel Instruction 3 Technical Parameter 4 Electrical Schematic 5 Installation 5 1 In General 5 2 Connecting With Water Supply 5 3 Connect with Waste Water Discharge 5 4 Connect with Overflow discharge 6 Operation 6 1 Attentions before Using 6 2 Connect to Power Supply 7 Different Functional Systems 7 1 Filtration System 7 2 Hot Water System 7 3 Cold Water System 7 4 Sterilization System 8 Common Operation 1 Get Hot Water 2 Get Cold Water 3 Get One Cup of Mixed Water 4 Extra Hot Function 9 Maintenance and replacement 9 1 Filter Replacement 9 2 Clean the Tanks 9 3 Clean the Dust Cover 9 4 Clean Machine 10 Precautions 11 Trouble Shootings 2 18 Page 3 Page 4 5 Page 6 Page 7 Page 8 9 Page 9 10 Page 10 11 Page11 12 Page 12 16 Page 17 Page 18 1 Functional module configuration table Filtration System Sterilization Controlling System ACF ACF UF ACF RO Ozone po Lele je e ej of e lol je Note This model have different functional options when you see this user manual Electronic O0 O OJO Laer acrour acre RO NN ua
8. chine out of table for around 20cm hook the dust cover by hand and pull it out E gt eT LZ iu ui es Cou i TR D VT ei i LS pu ur dum Hot Tank Drain Hole It s anzi eT a S 9 3 Clean the Dust Cover Move machine out of table for around 20cm hook the dust cover by hand and pull it out Use close or brush to clean the dust on it then put it back Note To clean the dust cover regularly can help machine to keep good ventilation performance making sure each functional modules can work efficiently 9 4 Clean Machine Please clean the unit with soft cloth dipped in warm water or neutral detergent To clean the display panel and decorative panel please use soft dry cloth Do not use rough detergents concentrated washing liquid solvent or anything that may scratch the machine materials such as steel wool steel balls etc Attention If it connects with power supply when you cleaning the machine make sure not make the back of machine damp 16 18 10 Precautions The machine is only for indoor use please do not put under direct sunlight Do not put flammable material beside the machine Do not put valuable appliance beside machine to prevent being damp Do not sink machine into water OThis machine adopts the 230VAC or 120vac voltage need to use with a 10A fuse socket Please use safety and reliable electrical devices during the operation and repairing When use the machine for the first tim
9. chine will detect there no water in tank and automatically enter making water mode The water making icon lights on at the same time the water fill into hot and cold tank when all the tanks are full the water making icon lights off The making water process finishes Note This clause only applies to the machine with ACF filtration system or UF filtration system 7 1 2 ROFiltration System After connected with electricity supply all the icons on the display panel shin for one second the indicator light see outlook instruction become blue the machine enter working mode Machine will detect there no water in tank and RO system enter flashing mode After flash for 18 seconds machine enter water making mode and the water making icon lights on At the same time the water fill into hot and cold tank when all the tanks are full the water making icon lights off The making water process finishes Note This clause only applies to the machine with RO filtration system 7 2 Hot Water System After filling water process is finished you can choose to turn on hot water function Turn on the heating switch at the back of machine the heating icon lights on And the heating system is working when the heating icon lights off the heating process finishes Note This clause only applies to the machine with heating system 7 3 Cold Water System After filling water process is finished you can choose to turn on cold water function Turn on the
10. e or after cleaning please turn on heating switch after make sure there is water come out of faucet to prevent making any damage of machine The machine is safety and reliable there may a few drops after getting water it is a normal phenomenon Because there is no valve between tank and faucet and the water tank is not a pressure tank OThe machine can make hot water with high temperature children are forbidden to use machine without accompanied by adults The machine is forbidden to be used by disabilities or children unless supervised or guided by responsible persons The maintenance and service of machine must be taken by professional person the manufacturer and distributor will not undertake any direct or indirect loss caused by improper use or neglect of responsibility O For safety if you will not use machine for a long time such as on a holiday or long trip please cut off the water supply and power supply of the machine Please get and drain 10 15L water after turn on the machine again Please contact with your local dealer to get detailed explanation of operations and precautions Warning The machine must use three pin socket with a good grounding line and leakage protection switch 17 18 11 Trouble Shootings If you find machine not work properly please check the list blow and then decide if you need to find professional person to repair Possible Reason Settlement No water comes out No
11. er clockwise Close Install filter clockwise Picture 6 9 1 4 How to replace UV After remove the decorative panel you can see on the top there is UV installed see picture 4 Please do accordingly as following to replace UV Taking off UV Open Please find the UV replace tool on the accessory bag Insert UV Replace Tool into UV hole push out the buckle in the hole as the same time turn the UV counter clockwise to take off UV See picture 7 Install UV Close Hold UV and insert UV into cold tank Then turn UV clockwise and when you feel the buckle auto blocked the UV installation finishes See picture 7 UV Replace Tool Anti Skid Slip Picture 7 Note This clause only applies to the machine with UV system 9 1 5 How to change Ozone generator 14 18 The ozone generator is installed at the bottom of the machine See picture 8 Cause the replacement of ozone generator leads to install of electrical parts we suggest the replacement of ozone will be taken by professional service people It is described in detail here Hot Tank A5 Drain V2 lt A Water uw s Drain TT parti Picture 8 9 2 Clean Tanks If machine not be used for a long time it needs to clean the hot and cold tank to make sure the water is fresh 9 2 1 Clean Water Tank First please turn off the water supply and electricity supply Remove the decorative panel you will see the water tank cover check Picture 4 O
12. here are some changes on technical parameter 6 18 4 Electrical Schematic Electrical Schematic lul Sobol valve Gold Solenaid valve Cooling n E Fan i di i a Generator Relay Y Relay fel 77 Slashing Value ica ashing Value i Iinoster Eump 7 fa li A C3 Switch de x Sg ERE dealing Switch Contral CO i Sepol Cooling Swlirth d ra Board Ug ale Luna Level Eye ii Waler Fall Sw Lati Weater Level Alarm Slice 1 ka k k Cad Tank Water Button Child Lock Button Extra Hot Butta n Indicalor Lighl Board Hot Tank apys Haalin Elenieril P Thermostat Live Wire Fuse 10A Ground Wire Cumpre Neutral Wire Remark You may not be informed should there are some changes on technical parameter T 18 5 Installation 5 1 In General This machine is only suitable for indoor use and must be installed in a cool ventilated stable surface away from hot objects Leave at least 10cm 4 space at the back of the machine and leave enough space for machine at the right and left side We suggest that the installation take by professional people 5 2 Connect With Water Supply Please install the machine near the water supply not more than 3 meters far water pressure between 0 2 0 6MPa Before installation please check if all the accessories are all there a three way ball valve elbow quick connector PE pipe 5 2 1 Please shut off the wa
13. pen the water tank cover add clean water in tank and use soft cloth to clean tank After finished cleaning take off the water tank drain stopper at the bottom of machine When drain out all the water put the stopper in place The cleaning process of water tank finished Picture 9 9 2 2 Clean Hot Tank Note When you want to clean hot tank please turn off the heating switch Wait until the water coming from the hot tank become cool then start to clean 15 18 First please turn off the water supply and electricity supply Remove the decorative panel you will see the hot tank cover check Picture 4 Use tool to open the hot tank cover then put clean water into hot tank Use soft cloth or soft brush to clean the hot tank After that take off the hot tank drain stopper at the bottom of machine When drain out all the water put the stopper in place The cleaning process of hot water tank finished Please clean the unit with soft cloth dipped in warm water or neutral detergent To clean the display panel and decorative panel please use soft dry cloth Do not use rough detergents concentrated washing liquid solvent or anything that may scratch the machine materials such as steel wool steel balls etc Attention If it connects with power supply when you cleaning the machine make sure not make the back of machine damp Note If you find there are scales in hot tank you can put 596 citric acid into tank to clean the scales Move ma
14. ter supply and take off the faucet by turning counterclockwise see picture 1 z eem Picture 1 5 2 2 Please wrap the three way ball valve with tap special tap for water sealing Then install it with water supply pipe in one side and with faucet on the other side make sure it seals well Then connect the three way ball valve with PE pipe see picture 2 Three Way Ball Valve Picture 2 5 2 3 Connect the other side of PE pipe with the water inlet connector of machine Firstly take off the buckle and cap of connectors See A 1 and A 2 in Picture 3 Note when take off the cap you need to press the buckle Insert PE pipe into water inlet connector then install the buckle See 8 18 A 2 in Picture 3 dup Picture 3 5 3 Connect with Waste Water Discharge RO Version Connect the one side of PE pipe with waste water drain connector and another side into the floor drain or other reliable container Please refer the Picture 3 For RO version during making the pure water machine also produces waste water The waste water must discharge into floor drain Please check the drain pipe regularly If the drain pipe is blocked the waste water will back flow into the machine pollute the water and may also damage the machine Note This clause is only apply to the machine with RO system inside If you machine doesn t have RO system please ignore this clause 5 4 Connect with Overflow Discharge Please refer to the
15. vice staff to change filter eMust use reliable three pin socket elnstall an additional electricity leakage protector ePlease contact with our service staff eContact with our service staff to repair eShut off the power supply for 1 2 minutes then turn on the machine again Note If you find that the machines have quality problems please contact the nearest authorized service department came to repair or call the dealer to repair Please not disassemble machine yourself our company will not undertake any responsible for the damage and incident result from it 18 18
Download Pdf Manuals
Related Search