USERS MANUAL
Contents
1. Transfer this instruction manual upon change of marker ownership OPERATION GUIDE START UP WARNING Always keep the marker powered off or on SAFE until you are ready to shoot To install and charge the battery see pages 6 and 8 To turn the power ON slide the Selector Switch located on the rear of the trigger frame UP to SEMI w EYES SEMI or AUTO mode CAUTION With the power ON the marker is now ready to shoot Cock the marker by pulling the Snap T Cocking Handle 266 rearward until it latches CAUTION If you let go before the handle latches your marker may fire NOTE The Snap T Cocking Handle will latch the bolt internally the Handle will not remain in a cocked position after latching the bolt nor will it move while the marker is being fired You should hear an audible click and feel a tension release in the Handle when cocking the marker Firmly attach the CO2 Compressed Air Tank clockwise to the markers Dovetail Bottom Line ASA 261 It is recommended to use a Force Fed High Speed Electronic Loader that is capable of feeding paintballs into the marker at 17 balls per second or faster to avoid chopping paintballs in the markers breach when shooting at high rates of fire Routine lubrication of the marker does not require disassembly of the marker Put 3 4 drops of Paintball Marker Oil into the Bottom Line ASA 261 screw in your air tank point the marker in a safe direction and dry fire no Paintballs in the c2. MARS TABLE OF CONTENTS IMPORTANT SAFETY GUIDELINES l OPERATION GUIDE START UP 2 CO2 COMPRESSED AIR TANK 3 4 ELECTRONICS amp SETTINGS 5 6 BATTERY CHARGING 7 8 VELOCITY ADJUSTMENT 9 SHOULDER STOCK INSTALLATION 10 DISASSEMBLE REASSEMBLE amp CLEANING INTERNALS 11 12 T COCKING REMOVAL 13 TRIGGER ADJUSTMENT 14 ANTI CHOP EYES 15 16 CUP SEAL REMOVAL 17 18 MR3 SCHEMATICS 19 MR3 PARTS LIST 20 WARRANTY STATEMENT el WARRANTY REGISTRATION 22 IMPORTANT SAFETY GUIDELINES ICAUTION This paintball marker is NOT a toy It can cause serious injury or death e Kingman recommends that customers be at least 18 years of age to purchase this product e Read this manual and air system warnings before using this product Any modifications or tampering of original factory parts will void all warranties and liabilities from Kingman Kingman recommends using a barrel plug or barrel sock when marker is not in operation All persons using this product or within range while this product is in use must wear eye and face protection specifically designed for paintball e Never shoot at a person or an animal that is not in a designated paintball facility Treat every paintball marker as if it were loaded e Never look down the barrel of a loaded or unloaded marker e Always keep the paintball marker on SAFE until ready to operate e Always remove CO2 Compressed Air source before disassembly Fire only 0 68 caliber paintballs
3. Everytime the trigger set screws are repositioned use thread locker Loc Tite 242 Blue color to prevent from loosening INSTALLING A BATTERY STEP 1 Remove the 3 MUx8 screws 294 and left side grip panel 270 STEP 2 Attach the Spyder battery JE1015 to the Battery Harness E2UA STEP 3 Retighten the 3 MUx8 screws 294 HELPFUL TIP Please note how the parts are removed for easy reassembly REMOVING THE TOURNAMENT LOCK SWITCH STEP1 Remove the 3 MUx8 screws 2914 and left side grip panel 270 STEP 2 Remove the Tournament Lock Switch JE30B located to the right of the Spyder Battery HELPFUL TIP Having the Tournament Lock Switch removed from the circuit board will deactivate auto MODE SETTINGS Mode Switch Down is in the OFF Position MODE 1 Click Up is in Semi Auto with Eyes ON MODE Click Up is in Semi Auto with Eyes OFF MODE 3 Click Up is in Auto with Eyes OFF TOURNAMENT MODE SETTING The MR3 Circuit Board 331 is equipped with a Tournament Lock Out Switch JE30B When the Tournament Lock Switch is removed from the Circuit Board the marker can only fire in SEMI AUTO The Tournament Lock Switch is located on the internal Circuit Board to the right of the Battery Reattaching the Tournament Lock Switch JE30B back into the Circuit Board will re enable the multi mode functions IMPORTANT Kingman recommends that you use a force feed high speed electronic loader to reach optimum performance Kingman
4. has not been used in over a week SPYDER 9 6 NiMH BATTERY LIFE Always use the supplied Spyder 9 6volt NiMH Battery and Spyder Charger to operate this marker A fully charged Spyder Battery will last about 3000 to 5000 shots Number of shots depends on the settings of your firing methods Under normal use and charging conditions the expected life of the Spyder 9 6 NiMH Battery to last approximately 700 1000 charging cycles WARNING This marker is not attended to use any normal 9 volt battery or chargers that are NON Spyder Products Doing so will VOID all electronic warranties LOW BATTERY INDICATOR The LED light located beneath the mode switch on the back of the grip will blink rapidly when the battery power is low and will require charging VELOCITY ADJUSTMENT Decrease Velocity Increase Velocity VELOCITY ADJUSTMENT INCREASE DECREASE To increase your velocity FPS Feet per second using the allen wrench turn the Velocity Adjuster 296 clockwise To decrease your velocity FPS Feet per second using the allen wrench turn the Velocity Adjuster 296 counter clockwise NOTE Velocity Adjuster w Spring Guide 296 doesn t remove from the rear of the Striker Plug 260 WARNING The recommended Velocity speed should be no greater then 300fps Not doing so can cause serious injury if the velocity is dangerously high Paintball markers are not intended to shoot any person less then 25 feet Never point a load
5. 14010 Live Oak Avenue Baldwin Park CA 91706 U S A www kingman com FOR TECHINICAL SUPPORT Our Technical Support Department is open Monday through Friday from 8am to 5pm PST and can be reached at 626 430 2300 www spyder tv KINGMAN REGISTRATION PLEASE COMPLETE AND RETURN THIS FORM ALONG WITH A COPY OF YOUR PURCHASE RECEIPT WITHIN 15 DAYS OF PURCHASE SO THAT WE MAY VALIDATE YOUR 12 MONTH LIMITED WARRANTY NAME ADDRESS CITY STATE ZIP COUNTRY GENDER AGE JOB E MAIL PHONE PRODUCT NAME SERIAL WHAT OTHER BRAND S OF MARKERS DO YOU OWN WHY DID YOU PURCHASE THIS KINGMAN MARKER WHAT IS THE NEXT PAINTBALL PRODUCT YOU INTEND TO BUY WHAT ARE YOUR HOBBIES OTHER THAN PAINTBALL WHAT ARE SOME MAGAZINES YOU LIKE TO READ HAVE YOU MADE ANY ONLINE PURCHASES IN THE PAST 6 MONTHS Y N COMMENTS SUGGESTIONS YES WOULD LIKE TO RECEIVE MORE INFO REGARDING NEW PRODUCTS PROMOTIONS AND SPECIAL OFFERS FROM KINGMAN MAIL TO KINGMAN GROUP 14010 LIVE OAK AVE BALDWIN PARK CA 91706 USA 22 Distributed by Kingman Group 1 888 Kingman www kingman com 14010 Live Oak Ave Baldwin Park California 91706 USA
6. Valve Pin 326 MR3 Delrin Bolt Valve Body 327 MR3 Fore Grip Handle Valve Body Roll Pin 328 MR3 Sight Rail Valve Body Screw 329 MR3 Eye Detent Cover M5 x 12 Screw w washer 330 MR3 Trigger Frame Striker O Ring 331 MR3 Circuit Board Barrel O Ring 332 MR3 Miltary Adjustable Stock Striker Spring 333 MR3 Military Adjustable Stock Screw Striker Buffer 334 Flat x 8 Screw Filter O Ring 2608S Drop Forward Lock Screw Air Filter E2UA Battery Harness Trigger Pin JEl2 Sear Sear Roll Pin Small JE18A Striker Bolt Touch Switch Roll Pins JE18C Coil Set MR3 Wire Harness JEISE Coil Set Screw MR3 Vertical C A Adapter JE29 Circuit Board Screw MR3 Vertical C A to Hose Adapter JE31E ESP Sear Spring MR3 Reservoir Adapter Plug JE1015 9 6v Rechargeable Battery MR3 Bolt Pin A C Charger 110v MR3 Dovetail Drop Forward MR3 Striker Plug Not Pictured MR3 Dovetail Bottom Line ASA MR3 Quick Disconnect Pin MR3 Snap T Knob MR3 Snap T Clip MR3 Snap T Spring MR3 Snap Rail Cover MR3 Grip Panels MR3 Touch Switch w Wire Harness MR3 Blade Trigger MR3 Parts Kit MR3 Male STD Female Metric MR3 Disconnect Hose 6 25 black MU x 8 Screw w Washer MR3 Velocity Adjuster w Spring Guide MR3 Velocity Adjuster O Ring Trigger Set Screw 90 KINGMAN WARRANTY STATEMENT Kingman warrants the original retail purchaser that this product is free from defects in material and workmanship under normal use and service for a per
7. with a rag or paper towel The Striker O Ring 19A will need to be oiled periodically Kingman recommends that each time the back internals are removed the Striker O Ring 19A should be oiled IMPORTANT Never oil the Delrin Venturi Bolt 326 This will swell the bolt and cause cocking problems Striker Buffer 26A should be installed behind the Striker Bolt JE18A to ensure proper functioning WARNING Never attempt to remove the markers internals while the CO2 Compressed Air bottle is attached Make sure to remove all paintballs and loader before disassembling the marker 12 13 T COCKING REMOVAL T COCKING REMOVAL STEP 1 Remove Flat MY x 8 Screw 334 STEP 2 Slide the Snap Rail Cover 269 toward the rear of the marker STEP 3 Remove Snap T Knob 266 STEP U Remove the Snap T Clip 267 NOTE Be careful while removing the Snap T Springs 268 as the tension may cause them to fly off HELPFUL TIP Please note how the parts are removed for easy reassembly TRIGGER ADJUSTMENT Z f 298 HEN ard re N N me N i 273 ed E A a N So N TRIGGER ADJUSTMENT Adjusting the Top Trigger Set Screw 298 clockwise will swing the Trigger 273 closer the Touch Switch 272 which will lessen the tri
8. also recommends the use of a Spyder CO2 Compressed Air Tank to operate this marker Lastly the use of tournament grade paint will help reduce the likelihood of paintball breaks when firing the marker WARNING e The Spyder Electronic Markers are not water resistant e Extreme moisture can cause serious damage to any Spyder Electronic Markers e Always clean any dirt or paint inside the Markers Electronics Never attempt to modify the Electronics circuitry Doing so it will VOID all electronic warranties NOTE If the Markers Electronics have any dirt or paint Kingman recommends using an aerosol can of air Apply the can of air directly at the components that need cleaning BATTERY CHARGING JE1024 or JEI025 CHARGING INSTRUCTIONS To charge a Spyder 9 6 NiMH Battery the circuit board must be in the OFF Position Spyder Batteries JE1015 are not fully charged when purchased Using the supplied Spyder Charger JE102U place the charger in the charging port which is located at the rear of the trigger frame Kingman recommends a charging time of 6 8 hours for a complete charge IMPORTANT You should never charge the battery over 24 hours or you can run the risk of damaging the battery or electronics The battery charger will continue to power until removed from charging port NOTE It is recommended that the battery be chagred prior to use in order to ensure maximum performance especially if the battery
9. of CO2 Compressed Air leaking down the barrel STEP 1 Loosen the Disconnect Hose 290 from the collar STEP 2 Loosen the 2 set screws M5x12 16 STEP 3 Remove the Fore Grip Handle 327 STEP YU Loosen the 2 set screws M5x12 16 STEP 5 Remove the Shroud 322 Once the steps have been completed this will allow the Reservoir Plug 254 to slide out with the Valve Spring 10C Cup Seal Guide 11 Cup Seal 12 and Valve Pin 13 HELPFUL TIP Please note how the parts are removed for easy reassembly HELPFUL HINTS Always remove the Air Tank before any disassembly of your marker Do not remove the Valve Body 14 unless specific Valve Body repairs are needed If needed remove Valve Body with a long soft tipped object such as the eraser end of a pencil Do not remove the Valve Body with a screwdriver as it will damage the Valve Body and cause air leaks NOTE Valve Body 15 screw must be removed prior to taking out the Valve Body 18 MR3 SCHEMATICS areari zar MR3 PARTS LIST Barrel Plug 320 MR3 10 Barrel Ball Stopper 321 MR3 Feed Neck O Ring 015 80D 322 MR3 Shroud Valve Spring 323 MR3 Rifle Sight Cup Seal Guide 324 MR3 Rifle Sight Screw Cup Seal 325 MR3 Receiver
10. e ASA 261 HELPFUL TIP Make sure when installing a tank to have the CO2 Commpressed Air Tank filled Make sure the CO2 Compressed Air Tank has a bottle o ring on the top of the valve to prevent air leaks REMOVING A CO2 COMPRESSED AIR TANK Firmly unscrew the CO2 Compressed Air Tank by turning counter clockwise HELPFUL TIP After playing with the marker you should ALWAYS remove the CO2 Commpressed Air Tank When the Tank is being removed excess air will release from the bottom of the Dovetail Line ASA 261 IMPORTANT Never expose any skin underneath the Dovetail Bottom Line ASA 261 when removing the Tank This can run the risk getting skin burn from releasing the GAS Never store any CO2 Comppressed Air Tank attached to the marker CO2 COMPRESSED AIR TANK WARNINGS All valves must only be installed or removed by a qualified airsmith See CO2 Compressed Air tank labels for retest dates Cylinder tanks must be retested periodically Improper use filling storage or disposal of all air cylinders may result in death personal injury and or Property damage Always keep cylinders out of reach from children or any inexperienced person s Only properly trained personnel in accordance with CGA Pamphlets P 1 and G 6 3 must fill all air cylinders Pamphlets are available from the Compressed Gas Association or www CGANET com Never alter the cylinder in any way e DO NOT expose pressurized cylinders to
11. e Receiver 325 Paintballs may be defective i e expired odd shape etc After ball breaks in Barrel or chamber remove all parts from upper chamber of Receiver wipe parts clean and reassemble parts into Receiver Also make sure to clean the Barrel with a squeegee DISASSEMBLE REAR INTERNALS STEP 1 Remove Quick Disconnect Pin 262 NOTE Place a finger over the Striker Plug 260 before removing the Quick Disconnect Pin 262 STEP 2 Remove the Striker Plug 262 Main Spring 25 Striker Buffer 26A STEP 3 Remove the following items at the same time Striker Bolt JE18A and the Delrin Venturi Blot 326 HELPFUL TIP Please note how the parts are removed for easy reassembly REASSEMBLE REAR INTERNALS When reassembling the Delrin Venturi Bolt 326 and Striker Bolt JE18A the circuit board must be powered ON with the Eyes OFF Join the Delrin Venturi Bolt 326 and Striker Bolt JE18A together entering the back end of the Receiver 325 Simultaneously pull the Blade Trigger 273 and apply pressure behind the Delrin Venturi Bolt 326 to allow reentry of both parts Reinstall the Striker Buffer 26A Striker Spring 25 Striker Plug 260 and press in the Quick Disconnect Pin 262 to lock down all back internals HELPFUL TIP When the back internals are removed it would be wise to clean any dirt or paint from inside the Receiver 325 with a stick swab or cable squeegee Wipe the Delrin Venturi Bolt 326
12. ed marker at any person who is not wearing the proper face protection e Never at any time should you look down the barrel when the marker is loaded or not e Using a paintball marker outside a non designated paintball field can be illegal and is subject to law enforcement penalties if property damage is caused by the user SHOULDER STOCK INSTALLATION SHOULDER STOCK 332 SHOULDER STOCK INSTALLATION Place the Shoulder Stock 332 on the back end upper section of the Receiver 325 Once the Shoulder Stock is in place tighten the Set Screw 16 to secure the stock to the body of the marker The Set Screw 16 is located on the right side of the receiver ADJUSTING SHOULDER STOCK LENGTH Turning the Shoulder Stock Screw 333 counter clockwise will loosen the Shoulder Stock allowing for three different lengths to be achieved Not Pictured 10 11 DISASSEMBLE REASSEMBLE amp CLEANING INTERNALS TROUBLESHOOTING ONE OR MORE OF THE FOLLOWING MAY CAUSE RECOCKING RELATED PROBLEMS The pressure in the tank is too low In some cases the weather can affect the liquid in the tank and not cause it not to expand into carbon dioxide gas Marker needs lubrication Venturi Bolt 326 needs to be cleaned The Striker O ring 19A is damaged Replace with new Kingman or Kingman approved O ring NOTE The O ring 19 cannot be substituted by a tank O ring or an 09 O ring Need to clean Barrel and upper chamber of th
13. gger gap NOTE Adjusting the Trigger Set Screw 298 counter clockwise will increase the trigger gap Adjusting the lower Trigger Set Screw 298 clockwise will shorten the Trigger 273 stroke to the Touch Switch 272 this will increase Trigger 273 sensitivity NOTE Adjusting the Trigger Set Screw 298 counter clock wise will decrease the Trigger 273 sensitivity 14 ANTI CHOP EYES ANTI CHOP EYES The Anti Chop Eyes help prevent chopping paint by not allowing the marker to fire until a paintball is in front of the Venturi Bolt The Eyes transmit a beam across the inside of the breech The Circuit Board is preset from the factory and does not need to be adjusted or altered If the Eyes are ON and do not see each other when firing your marker you will have to clean the Eyes CLEANING THE ANTI CHOP EYES Using a squeegee or swab thru the breech should clean the Eyes enough for the beams to detect each other Another way is to use an aerosol can of air thru the breech to remove paint or dirt from the Eyes To thoroughly clean the Eyes remove all MU x 8 Screws 294 including the lower screw not pictured which holds the Feed Neck the Eye Detent Cover 329 and the Feed Neck 321 using an allen wrench Once the MU x 8 Screws 294 Eye Detent Cover 329 and Feed Neck 321 are removed precede with a soft pinch to remove the Eye Wire Harness 243 from the receiver Remove all dirt or paint that is blocking the E
14. hamber 5 10 shots This procedure will circulate oil through the markers internal parts thus ex tending the life of the marker NOTE Only use oil that is specifically designed for paintball markers It is a good practice to lubricate your marker before and after each use especially when storing the marker for an extended period of time When you are finished shooting the marker be sure to remove the Loader and all paintballs before storing NOTE There may be a paintball in the breach of the marker take a couple of shots in a safe direction to make sure that the Barrel and breach are empty Place the Barrel Plug into the Barrel to avoid accidental discharge of the marker Turn the marker OFF and slowly unscrew the air source tank CAUTION Do not remove the Tank Valve from the Tank doing so may cause serious injury or death CO2 COMPRESSED AIR TANK DANGER The CO2 or Compressed Air Tank can fly off with enough force to cause serious injury or death if the Valve unscrews from the cylinder head LOOK at the Valve when removing the cylinder from the marker Be sure that the valve is turning with the cylinder rather than remaining stationary with the marker STOP if the Valve starts to unscrew from the cylinder If in doubt screw the cylinder back onto the marker and contact a trained person for repair INSTALLING A CO2 COMPRESSED AIR TANK Firmly attach the CO2 Compressed Air Tank clockwise to the markers Dovetail Bottom Lin
15. iod of 1 year from the original date of purchase Any Electronic Components in an Electronic Spyder marker are warranted for 6 months from the original date of purchase Kingman agrees to repair or replace at its discretion any product within a reasonable period of time This warranty does not cover o rings cup seals 9 6v rechargeable battery charger scratches nicks normal wear and tear of parts any modifica tions normal fading of anodizing and damage caused by dropping or hitting of products This warranty shall not apply if it is shown by a Kingman Technician that the consumer caused the defect or malfunction because of misuse This warranty only covers original factory parts Any modifications or tampering of original factory parts will VOID warranty Any damage caused by water will not be covered under warranty Warranty repair can only be conducted by Kingman technician or Kingman authorized technician For warranty to be effective consumer must return the enclosed warranty registration card filled out along with a copy of the purchase receipt within 15 days of the original purchase date This warranty is not transferable Paintball markers are non refundable This warranty will not cover pick up shipping delivery and or house calls If product needs repair consumer will package it carefully and send together with your name address phone number and a brief description of the malfunction to KINGMAN GROUP Attn Tech Department
16. temperatures in excess of 130 F 54 C Cylinders heated to an excess of 250 F 121 C must be condemned or requalified in accordance with test defined in CFR 49 The valve should NEVER be detached from the canister Please seek immediate assistance from a trained airsmith should this occur e Anutank packed with the product is intended for paintball use only Confirm that there is an attached urethane O ring on the CO2 Compressed Air tank valve before attaching the tank to the marker The tank will leak air as soon as it is secured to the marker if the O ring is missing from the valve A urethane O ring is highly recommended before attaching any air supply to the marker NEVER over pressurize a CO2 Compressed Air cylinder e Avoid any direct skin exposure to the escaping gas when installing or removing any air supply e Never expose cylinders to corrosive materials or clean with any caustic cleaners ELECTRONICS amp SETTINGS yy sem SEMVEYES 1 OFF ELECTRONIC GRIP TROUBLESHOOTING e Check to make sure there is enough air pressure to fire the marker e Battery may need to be recharged Ifthe Trigger is not functioning turn the Trigger Screw 298 clockwise to shorten the gap between the Touch Switch 272 using an allen wrench NOTE Do not over extend the Trigger Screw 298 for this can cause the Touch Switch 272 to stick
17. yes and causing it to malfunction HELPFUL TIP Please note how the parts are removed for easy reassembly IMPORTANT Cleaning the Eyes often will help reduce dirt paint or oil residue that blocks the Eyes from seeing each other NOTE Never attempt to rush the cleaning process or you can pinch the wires and cause the marker to malfunction with the Eye Mode ON Take precaution not to over tighten the MU x 8 Screw 294 or this can lead stripping the head CHANGING THE BALL DETENTS Experiencing paint rolling through the barrel can be related to small diameter of paintballs or the lost of a ball detent s When removing the Eye Detent Cover 329 and Feed Neck 321 the Ball Detents 03 will become accessable to be cleaned or replaced HELPFUL TIP Please note how the parts are removed for easy reassembly NOTE Take precaution not to over tighten the x 8 294 or this can lead to stripping the head 16 CUP SEAL REMOVAL Jt TL i Ts coLLar Y E STEP 5 322 STEP BY STEP CUP SEAL ACCESS The following steps will provide easy accessto the Cup Seal 12 The sign of a worn out Cup Seal 12 is the presence
Download Pdf Manuals
Related Search