LED BEAM 7* 15W 4in1 User Manual
Contents
1. main before starting maintenance operation In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakness of the light due to accumulation of dust 2 Clean the fan each week 3 A detailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instruction under Installation instruction Should you need any spare parts please order genuine parts from your local dealer www flash butrym pl Page 10 www flash butrym pl Page 112. necessary for the user to follow the safety instructions and warning notes written in this user manual Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class 1 Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate voltage and frequency Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device in not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more the 50cm dis
3. activated controllable or auto operation High definition blue TFT LCD display Quiet smooth and fast PAN TILT movement Low noise and efficient FAN cooling system 540 PAN and 250 TILT movement Scan position memory auto reposition after unexpected movement Compact size with only 4 9KG body and 310mm in height IEC power connector 45 C max ambient temperature IP20 protection rating 3 pin XLR DMX input output 10 Specification Input Voltage AC90 260V 50 60Hz LED Quantities 7PCS of 15W OSRAM 4 IN 1 LEDs R G B W Control Signal DMX512 channels power Consumption 100W Dimension 152 L 265 W 310 H mm Packing Dimension 260 L 320 W 335 H mm Net Weight 5 5kg www flash butrym pl Page 9 Gross Weight 7 5kg 11 Maintenance and Cleaning The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show and damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed CUATION Disconnect from
4. le rigging point in the unit When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the omega bracket As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using the safety cable rigging point integrated in the base assembly Omega Bracket D atety Clamp D alety Cable Dija Turn Quick Lock Fasteners Regardless of the rigging option you choose for your LED BEAM 120F always be sure to secure your fixture with a safety cable The fixture provides a built in rigging point for a safety cable on the hanging bracket as illustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle DMX 512 Control Connections Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors DMX 512 connection with DMX terminator www flash butrym pl Page 5 CONTROLLER DMX Output 3 Pin XLR Socket 3850 MUR Socket COMMON 1 Ground DMX posou A D 0 osen Oat SPINA SPN XLR For installation where the DMX cable has to run a long distance or is in an electrically nois
5. right 10 White 0 255 0 100 white dimmer from dark to bright 11 Colors Choice 0 255 Colors changing effect 12 0 010 CH1 Ch11 Activated 011 120 Colors jumping Macros and Sound control 121 180 Colors Fading 181 244 Colors mixing and strobe 245 255 Sound control 13 Macros Speed 0 255 Speed of macros 14 PAN TILT Speed 0 255 Speed control of PAN TILT fast to slow www flash butrym pl Page 7 15 0 244 CH1 CH14 Activated Reset 245 255 Reset after 3 seconds 8 Photometric Data Photometric Beam Angle Data 8 Beam Angle LUX x 0 0929 FC R 348 3750 45 480 17 180 9 90 G 466 5020 61 660 23 285 13 140 B 1098 11820 125 1350 44 7 470 22 240 W 1005 10810 122 1310 43 460 21 283 RGBW 2731 29400 333 3580 116 285 60 684 Om 0ft 1m 3 3ft 3m 9 8ft 5m 16 4ft 7m 23 Oft 9 Key Features 7PCS OSRAM 15W 4 IN 1 LEDs R G B W 60 000 hours life span doe LEDs and low power consumption Intelligent temperature sensor for LEDs over heat protection High efficiency 8 degree optic lens Color range with 16 7 million additive RGBW colors www flash butrym pl Page 8 High light output as 860LUX 7M at full 0 100 smooth linear dimmer with flicker free 20t s strobe effect with variable speed Pre programmed random strobe and pulse effects 15CH DMX channel Built in programs with macro effects DMX512 master slave and sound
6. tance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation www flash butrym pl Page 3 If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard 3 Operation Instructions The moving head is for beam effect for onside decoration purpose Don t turn on the fixture if it s been through severe temperature difference like after transportation because it might damage the right due to the environment change So make sure to operate the fixture until is in normal temperature This light should be keep away from strong shaking during any transportation or movement Don t pull up the light by only the head or it might cause damages to the mechanical parts Don t expose the fixture in overheat moisture or environment with too much dust when installing it And don t lay any power cables on the floor Or it might cause electric shock to the people Make sure the installation place is in good and safety condition before installing the fixture Make sure to put the safety chain and check it whether the screws are screwed properly when installing the fixture Make sure the lens are in good condition It s recommended to replace the units if there are any damages or severe scratch Make sure the fixture is operated by qualified person who knows the fix
7. ture before using keep the original packages if any second shipment is needed Don t try to change the fixture without any instruction by the manufacturer or the appointed repairing agencies It is not warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation like shock short circuit electronic shock lamp broke etc 4 Mounting and Installation Cautions For added protection mount the fixtures in areas outside walking paths seating areas or in areas were the fixture might be reached by unauthorized person Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture From a periodic safety inspection of all installation material and the fixture If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury www flash butrym pl Page 4 Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet Clamp Mounting The LED BEAM 120F provides a unique mounting bracket assembly that integrates the bottom of the base the included Omega Bracket and the safety cab
8. www flash butrym pl LED BEAM 7 15W 4in1 User Manual Unpacking Thank you for choosing our Beam For your safety Please read this manual before installing the device This manual cover the important information on installation and applications Please install and operate the fixture with following instructions Meanwhile please keep this manual well for future needs This Fixture is made of a new type of high temperature strength of engineering plastics and cast aluminum casing with nice outlook The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol It s available independently controlled and linkable with each other for operation And it is applicable for large scale live performances theater studio nightclubs and discos 4 IN 1 LEDs RGBW which features high brightness and stability Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation And please check whether the following items are included inside the box Moving Head One Power Cable One User Manual One www flash butrym pl Page 2 2 Safety Instructions CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely
9. y environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 6 Menu Operation Item Setting Function 1 D 001 512 DMX Add Setting No No DMX Signal Yes DMX Signal Insert 2 Invert Pan Positive Inversion 99 ce Motor Direction Setting Tilt Positive Inversion 3 CLND 15CH Channel Model 4 SLND SLNT Master Slave Master Slave Setting MAST Auto 5 DISPLAV ON Edit mode OFF 6 SOUND Setting ON OFF 7 CODE ON www flash butrym pl OFF 8 RESET ON OFF 9 MANUAL Setting ON OFF 7 DMX Channel Channel Function Values Description 1 Pan 0 255 PAN Movement 2 Pan Fine 0 255 Fine control of pan movement 16Bit 3 Tilt 0 255 Tilt Movement 4 Tilt Fine 0 255 Fine Control of Tilt movement 16Bit 5 Dimmer 0 255 0 100 Linear dimmer from dark to bright 6 Strobe Mode 0 15 Empty 16 95 Normal speed strobe 96 175 From fast to slowly 176 255 From slowly to faster 7 Red 0 255 0 100 Red dimmer from dark to bright 8 Green 0 255 0 100 Green dimmer from dark to bright 9 Blue 0 255 0 100 Blue dimmer from dark to b
Download Pdf Manuals
Related Search