SRE 188 E
Contents
1. autoclean procedure The display will show the autocleaningcode CAS running back tot The procedure takes 5 minutes during which the heater will burn at its lowest setting while the burner autocleans When the burner is clean again the heater will automatically switch back to the highest setting again CHILDPROOF LOCK The childproof lock can be used to prevent children accidentally changing the I When the KEY LOCK light lights up the childproof lock has been can only be switched off Other functions are blocked then If the heater has already activated heater settings When the heater is burning and the childproof lock is on the heater been switched off the childproof lock also prevents accidental ignition of the heater Activate the childproof lock by pressing the appropriate key and holding it hour min extension down for more than 3 seconds The KEY LOCK indicator light will light up Fig 1 d ES or indicating that the childproof lock has been activated Switch off the childproof lock o timer save by pressing the key and holding it down for more than 3 seconds once again vent fuel J When the SAVE light J THE CORRECT USE OF SAVE lights up the heater will The SAVE function allows you to limit the temperature When this function is automatically switch on activated the heater will automatically switch off when the room temperature exceeds or off in order to remain within a specified temperature r2. for sufficient fuel in the removable tank The temperature setting can only be adjusted when the heater is burning Use the adjustment keys to adjust the temperature First press either of the two keys to switch on the function the TEMP light next to the information display will start blinking Next adjust the temperature using the key on the right amp min to set the temperature to a higher setting and the key on the left hour to lower the temperature Press once to increase the value one step After approximately 10 seconds the light will stop blinking and the setting will be locked Fig G H The available temperature settings range from 6 C minimum to 28 C maximum When the heater has been unplugged for more than 10 minutes or after a power failure the temperature will reset to the factory setting of 20 C F USING THE TIMER The timer allows you to switch on the heater automatically at a preset time In order to switch on the timer the correct time must have been set refer to Section C and the heater should be off Follow the procedure below H Press the button B and then the TIMER key B immediately after that The TIMER light and the information display will start blinking H Use the adjustment keys to set the time at which the heater must ignite Use the key on the left hour to set the hours and the key on the right min to set the minutes interval of 5 minutes 3 After approximately 10 se
3. temperature changes Always store the fuel in a cool dry and dark place sunlight will affect the quality 8 Never use the heater in places where harmful gasses or fumes may be present e g exhaust gasses or paint fumes 9 Beware that the grid of the heater becomes hot If the appliance is covered there is a risk of fire 10 Always make sure that there is sufficient ventilation Defective electrical devices and batteries must be kept separate from household waste Ensure that there is effective recycling where possible Ask you local council GB or dealer for expert advice on recycling D Eh re ee ee SS re 1 D Mill IN Wun EE D Cle lea CE ie weer we timer save I a 5 R T 7 clock f e set vent fuel im wm em Ge Lin DISTRIBUTED IN EUROPE BY PVG INTERNATIONAL b v PVG Austria VertriebsgmbH Salaberg 49 3350 HAAG tel 43 7434 44867 fax 43 7434 44868 email pvgaustria zibro com PVG Belgium NV SA Industrielaan 55 2900 SCHOTEN tel 32 3 326 39 39 fax 32 3 326 26 39 email pvgbelgium zibro com PVG Schweiz AG Salinenstrasse 63 4133 PRATTELN tel 41 61 337 26 51 fax 41 61 337 26 78 email pvgint zibro com PVG Deutschland GmbH Siemensstrasse 31 47533 KLEVE tel 0800 9427646 fax 31 0 412 648 385 email pvgdeutschland zibro com Appliance A S Blovstroed Tegl
4. 50 Hz Burning time per tank hr 15 7 Electrical consumption igniter 320W Capacity removable tank litres 7 6 continuous 31 W Weight kg 13 5 Fuse rating 250V 5A Monitoring of the quality of ventilation air renewal GB Direct measurement of the CO level NDIR CO sensor E Guard At maximum setting Specified values are indicative H R WARRANTY PROVISIONS Your heater comes with a 24 month warranty starting on the date of purchase Within this period all defects in material or workmanship will be repaired without any charge The following provisions shall apply regarding this warranty H We expressly dismiss all other claims for damages including consequential damages H Any repairs or replacements of components within the term of warranty will not result in an extension of the term of warranty 3 The warranty shall no longer apply when the heater has been modified non original parts have been used or when it is repaired by third parties 4 The warranty shall not apply to parts that are subject to normal wear such as the burner mat and the manual fuel pump D The warranty shall only apply when you present the original dated proof of purchase provided no changes have been made toit D The warranty shall not apply to damages caused by actions not in compliance with the Directions for Use neglect and the use of an incorrect type of fuel or fuel past its use by date The use of incorrect fuel can even be danger
5. 7 47 Fax 02 32 96 07 77 Si une difficult subsistait vous pouvez crire au LNE LABORATOIRE NATIONAL DE M TROLOGIE ET D ESSAIS Division Certification plurisectorielle 1 Rue Gaston Boisier 75724 PARIS CEDEX 15 Dear Sir Madam Congratulations with your purchase of the Zibro the number one brand among movable heaters You have purchased a first class quality product which will serve you for many years to come This of course provided you use the heater correctly Please read these Directions for Use first to ensure maximum lifetime for your Zibro Your heater comes with a 24 month manufacturer s warranty on all defects in material or workmanship We wish you much warmth and comfort with your Zibro Yours sincerely PVG International b v Customer Service Department 1 READ THE DIRECTIONS FOR USE FIRST 2 IN CASE OF ANY DOUBT CONTACT YOUR ZIBRO DEALER 3 BEFORE YOU START READING FOLD OUT THE LAST PAGE P gt GENERAL DIRECTIONS FOR USE Below you will find the main steps to be taken for using your Zibro For more details please refer to the MANUAL pages 45 ff Remove all packaging materials Fig A Fill the removable tank refer to Section B Fig D Insert the plug into the wall socket Ignite the heater using the key B refer to Section D If required change the temperature using the adjustment keys refer to Section E Switch off the heater by pressing the key B e
6. The first time you ignite your heater it will smell like new for a short time e Store your fuel in a cool and dark place e Fuel has a limited shelf life Start every heating season with renewed fuel e The right quality of fuel will be assured when you use Zibro Extra or Zibro Kristal for your heater e If you change to another brand and or type of parrafin oil you must first finish up all the remaining fuel in the heater MAIN COMPONENTS o e o d Vd d Q 10 d 12 13 14 Front plate Grid Base plate Lid for removable tank Operation panel Handle Removable tank Air filter cap Vent filter Thermostat Plug cord Information display O key Childproof lock Adjustment keys time and temperature TIMER SAVE key Indicator lights EXTENSION Connection weektimer loniser Air quality control system Only the use of the correct fuel will ensure safe efficient and comfortable use of your Zibro The fuel cap cover can be found at the rear of the heater This cover allows you to keep your hands clean when opening the fuel tank This transportation cap is packed separately in the box Only this cap ensures trouble free transportation of the heater after use Store it well GB WHAT YOU NEED TO KNOW IN ADVANCE ALWAYS MAKE SURE THAT THERE IS SUFFICIENT VENTILATION This heater is equipped with an air quality control system When there is insuffici
7. ZIbro SRE 188 E guarantee YEARS MANUEL D UTILISATION GEBRAUCHSANWEISUNG BRUGSANVISNING INSTRUCCIONES DE USO OPERATING MANUAL ISTRUZIONI D USO GEBRUIKSAANWIJZING INSTRUKCJI OBS UGI AFAQ AFNOR CERTIFICATION 11 AVENUE FRANCIS DE PRESSENSE 93571 SAINT DENIS LA PLAINE CEDEX FICHE INFORMATIVE La marque NF garantit A S la qualit de cet article NTRS LE PAR a suivant les normes francaises CHAUFFAGES MOBILES et R gles de certification A COMBUSTIBLE LIQUIDE de l application NF 128 NF128 02 02 CONFORME A LA NORME NF D 35 300 ET AUX SPECIFICATIONS COMPLEMENTAIRES DEFINIES PAR LES REGLES DE CERTIFICATION DE L APPLICATION NF 128 PRINCIPALES CARACTERISTIQUES CERTIFIEES e S curit du dispositif d allumage e D bit calorifique e Efficacit des dispositifs de s curit e Stabilit e Contr le de la teneur en NO dans les produits de combustion e Contr le de la qualit de la combustion absence de CO e Endurance e Intermittence CONSEILS D UTILISATION ET D ENTRETIEN Se reporter la notice jointe l appareil et la plaque de s curit sur l appareil R f rence et num ro de lot ou de s rie de l article se reporter au produit Distributed in Europe by PVG International B V P O Box 96 5340 AB OSS Pays Bas T l 31 0 412 694670 En cas d insatisfaction consultez d abord En France PVG France SARL 4 Rue Jean Sib lius B P 185 76410 SOTTEVILLE SOUS LE VAL Tel 02 32 96 0
8. al information display will show the number of minutes of fuel left in are blinking in the information display You can stop this by pressing the the tank when it switches of The fuel indicator light will blink while four lines OO button B once more Once the heater has used up all its fuel and extinguished it will take some time after the refill before the heater is completely ready for use again L THE VENT INDICATOR LIGHT When there is insufficient ventilation in the room an intermittent buzzer will be heard approximately once each 30 seconds and the VENT indicator will be lit min exte When this signal is given ensure that the ventilation of the room is improved e g SZ ma Q by opening a door or window a little more to avoid that the heater shuts off wO timers When the ventilation of the room is improved the VENT indicator and buzzer will H o be deactivated When there is still insufficient ventilation the heater shuts off automatically When this occurs is displayed and the VENT indicator is L A blinking VENT indicator light is a sign blinking After improving the ventilation of the room e g by opening a door or that you need extra window a little more the heater can be ignited by pushing the on off button ventilation again If the indicator light continues blinking after extra ventilation please contact your Zibro dealer M THE IONIZER FUNCTION The ionizer can be activated by
9. ange again to the set temperature the heater will automatically switch on again Activate light up Fig J Switch off the function bv pressing the SAVE kev once again the set temperature by 3 C Subsequently when the room temperature has dropped the SAVE setting by pressing the appropriate key The SAVE indicator light will Without the SAVE setting your heater will maintain the set temperature by approximation as well by adjusting its heating capacity SAVE is an economy setting which you can use when for instance you are not present in the room or to keep it frost free K THE FUEL INDICATOR LIGHT When the indicator light FUEL lights up it means that there is only fuel left for 10 more minutes The count down of the remaining heating time can be seen in the information display Fig K Now you have two options gt you remove the fuel tank and refill it outside the living room section B or E a gt you LOL S CH SON By pushing this SURON Wie RARES s eating time will extend to 60 minutes The heater will automatically switch PE AR back to its lowest position In the display the number 60 will appear which set room vent fuel will decline to 10 At the arrival of 10 you will hear an alarmsignal every two K When the FUEL minutes warning you to refill the removable tank If you do not react the indicator light is lit the heater will extinguish by itself The heater will also sound a warning sign
10. conds the information display will show CLOCK again and the TIMER indicator light will light up indicating that the timer function has been activated Fig H H The TIMER indicator light indicates that the 4 The timer will ensure that the room will have been heated to approximately timer function has been switched on the required temperature at the set time When you want to switch off the heater and ignite it again with the timer all you have to do is press the TIMER key refer to Section G Press the button once to clear the timer setting G SWITCHING OFF THE HEATER There are two ways to switch off the heater H Press the button B The information display will show the CLOCK signal Within approximately one minute the flame will have extinguished H Press the TIMER key when you want to switch off the heater and ignite it again with the timer the next time This not only switches off the heater but it also activates the timer function You can change the required time with the adjustment keys B refer to Section F H THE INFORMATION DISPLAY The information display not only serves as an indicator of the set time and temperature Sections C E and F it also indicates any malfunctioning of the heater The code on the information display tells you what is the matter CODE INFORMATION WHAT TO DO L U Temperature within the heater too high Cool down and re ignite F U Power interrupted Re ignite the h
11. e H05 VV F STORAGE END OF THE HEATING SEASON At the end of the heating season you must store the heater in a dust free place if possible in its original packaging Unused fuel cannot be used in the next heating season We therefore recommend that you burn up all fuel If there is still some fuel left do not throw it away but dispose of it in accordance with the local regulations for the disposal of domestic chemical waste Always start the new heating season with fresh fuel When you start re using the heater follow the instructions again starting from section A and as specified TRANSPORTATION Take the following measures to avoid fuel leakage during the transportation of the heater H Let the heater cool down 2 Remove the removable tank from the heater and remove the fuel filter refer to Section N Fig N Some drops may leak from the filter keep a cloth at hand Store the fuel filter and the removable tank outside the heater 3 Place the transportation cap into the position of the fuel filter Fig O Press it tight 4 Always move the heater in an upright position Q SPECIFICATIONS Ignition electrical Dimensions mm width 550 Fuel paraffin including base plate depth 328 Capacity kW max 4 65 height 445 Capacity kW min 1 45 Accessories manual fuel pump Suitable space m 75 190 fuel cap cover transportation cap Fuel consumption I hr 0 484 Mains 220V 230V Fuel consumption g hr 388 AC
12. eater E j Faulty thermostat Contact your dealer F d Faulty burner thermistor Contact your dealer E g Starting problems Contact your dealer GB A Eoo gt Tipping over protection Re ignite the heater Fo MI 1 je AN Poor burning Contact your dealer Gs Room temperature If necessary above 32 C re ignite the heater Eo Defective booster Contact your dealer pe g Air filter dirty or Clean filter Fuel pump dirty Contact your dealer In case of any DI Ar The heater has been in operation continu malfunctioning the ously for a period of 50 hours and has information display will turned itself off automatically Switch the heater back on COMMUNS Se Out of fuel Refill removable tank matter amp blinking FUEL light Sn Too little ventilation Ventilate better amp blinking VENT light Eedi Too little ventilation Ventilate better amp blinking VENT light Always contact your Zibro Kamin dealer for any malfunctioning not listed above AUTOMATIC DEACTIVATION This heater is fitted with a safety system that ensures that it switches off automatically after 50 hours continuous operation The following will then appear CO LI in the display 5 fie If desired you can switch the heater on again by pressing the button B see Section D AUTOMATIC CLEANING MODE When te heater has been burning continuously for two hours at its highest setting the burner will automatically start an
13. ent ventilation in the room or when the heater is being used in a room which is too small the heater will shut off automatically For comfortable and safe heating ensure that there is sufficient ventilation Note To avoid unexpected shut off we recommend to put a door or window ajar when the heater is operating For each Zibro model the minimum size of space is specified in which you can use the heater safely without additional ventilation refer to Section Q If a particular room is smaller than the specified space always leave a window or door slightly ajar 2 5 cm We also recommend doing this in highly insulated or draught free rooms and or at altitudes above 1 500 metres Do not use your Zibro in cellars or other underground areas THE RIGHT FUEL Only use Class C1 paraffin fuel in accordance with BS2869 Part 2 or equivalent Your Zibro heater has been designed for use with high quality water free pure paraffin oil such as Zibro Extra or Zibro Kristal Only fuels of this kind will ensure clean and proper burning Lower quality fuel may result in increased possibility of malfunctioning incomplete burning reduced heater lifetime smoke and or smells vvvvyv deposits on the grid or mantle Using the right fuel is therefore essential for safe efficient and comfortable use of your heater Always refer to your local Zibro dealer for the right fuel for your heater A INSTALLING THE HEATER H Carefully remove your Zibro
14. from the box and check the contents In addition to the heater you also need to have gt a manual fuel pump gt a transportation cap gt a fuel cap cover gt these directions for use Keep the box and the packaging materials Fig A for storage and or transportation H Open the lid of the removable tank and remove the piece of cardboard 3 Fill the removable tank as indicated in Section B 4 The floor should be firm and completely level Reposition the heater when it is not level Do not try to correct the situation by placing books or other goods under the heater D Insert the plug into the wall socket 220 230 Volts AC 50 Hz and set the correct time using the adjustment keys refer to Section C D Your Zibro is now ready for use B FILLING FUEL Do not fill the removable tank in the living room but in a more suitable place there can always be some spillage Follow the procedure below H Make sure that the heater is switched off H Open the lid and lift the removable tank out of the heater Fig B Note Some drops may leak from the tank Put down the removable tank cap pointing upwards and screw off the fuel cap using the fuel cap cover Fig C 3 Take the manual fuel pump and insert the smooth most rigid tube into the jerrycan Make sure that it is in a higher position than the removable tank Fig D Insert the ribbed hose into the opening of the removable tank 4 Lock the sw
15. il you release the key again After approximately 10 indicator light stops blinking the setting has seconds the blinking will stop and the setting will be locked 5 minutes after been locked to the switching off the heater the information on the display will disappear and the indicated value heater will automatically switch into the stand by position When the heater has been unplugged for more than 10 minutes or after a power failure the time needs to be set again IGNITING THE HEATER When used for the first time a new heater may give out a smell for a short while You should therefore provide extra ventilation Always ignite the heater with the button B Never use matches or a cigarette lighter Just press the button B to ignite the heater The button will start blinking indicating that the ignition procedure has started This will take a short while Once the heater is burning the button B will remain lit red The information display ner save hour C A Q will show two numbers The light next to them indicates that these numbers refer to the temperatures Fig G The actual room temperature is indicated below ef ROOM while the temperature setting is indicated below SET The latter can be CIOC changed with the adjustment keys refer to Section E G The required temperature on the left the measured on on the E SETTING THE REQUIRED TEMPERATURE right Prior to igniting the heater alwavs check
16. itch button on top of the pump turn clockwise D Squeeze the pump a few times until fuel starts flowing into the removable tank As soon as this happens there is no need to press any longer GB D Check the removable tank fuel gauge while filling the tank Fig E Stop filling by loosening the switch button on top of the pump turn anti clock wise once the gauge indicates that the tank is full Never overfill the tank especially not when the fuel is very cold fuel expands when it heats up empty full Let the remaining fuel in the pump flow back into the jerrycan and carefully remove the pump Carefully screw the fuel cap back on the tank using the fuel cap cover After use re store the cover at the rear of the heater Clean off any spilled fuel Check whether the fuel cap is straight and tightened properly Reinstall the removable tank in the heater cap down Close the lid C SETTING THE CLOCK It is only possible to set the correct time when the heater is connected to the mains and not burning Use the adjustment keys B to set the time First press either of the two keys to switch on the function the CLOCK light and the information display will start blinking Next set the hours using the key on the left hour and the minutes using the key on the right amp min Press once to increase the value by one step When you hold down the key the value will F When the CLOCK continue going up unt
17. ous Transportation costs and the risks involved during the transportation of the heater or heater components shall always be for the account of the purchaser In order to avoid unnecessary costs we recommend that you always read the Directions for Use carefully first In case they offer no solution please take the heater to your dealer for repair Highly inflammable substances may induce uncontrollable burning causing flames to break out Should this happen never try to move the heater but always switch off the heater immediately In case of emergency you may use a fire extinguisher but only a type B extinguisher a carbon dioxide or powder extinguisher 10 TIPS FOR SAFE USE 1 Make sure that children are always aware of the presence of a burning heater 2 Do not move the heater when it is burning or still hot Do not refill nor service the heater when it is burning or still hot 3 Position the front of the heater at a distance of minimum 1 5 metres from walls curtains and furniture 4 Do not use the heater in dusty rooms You will not have optimum burning in such rooms Do not use the heater in the immediate surrounding of a bath a shower or a swimmingpool 5 Switch off the heater before you leave or go sleeping Unplug the heater as well when you go away for a longer period of time e g holidays 6 Store and move fuel only in suitable tanks and jerrycans 7 Make sure that the fuel is not exposed to heat or extreme
18. pressing the IONIZER button In this case negative ions are generated bringing air vitamins to a natural level This function can be used when the heater is de activated also To switch off the ionizer function the IONIZER button should be pressed again N MAINTENANCE Switch off the heater and let it cool down before you start any maintenance work Also disconnect the plug from the mains Your Zibro needs hardly any maintenance It is however important that you clean the air filter cap and the vent filter with a vacuum cleaner and the grid with a damp cloth both on a weekly basis Remove the air filter cap occasionally Fig M and clean it with soapy water Prior to reinstallation make sure that the air filter cap has fully dried ED ANNA JA Regularly inspect the fuel filter as well H Remove the removable tank from the heater and remove the fuel filter Fig N Some drops may leak from the filter keep a cloth at hand H Remove the dirt by tapping the fuel filter upside down against a hard surface Never clean it with water 3 Reinstall the fuel filter into the heater We recommend that you remove dust and stains in time with a damp cloth becau se otherwise these may cause stains that are hard to remove Do not remove any heater components yourself Always contact your Zibro dealer for repairs When the power cord is damaged it may only be replaced by an authorised fitter Use a new cord of the typ
19. vaerksvej 3 DK 3450 ALLEROED tel 45 70 205 701 fax 45 70 208 701 email appliance appliance group com PVG Espana S A Pol Ind San Jos de Valderas II Comunidad La Alameda C Aurora Boreal 19 28918 LEGANES Madrid tel 34 91 611 31 13 fax 34 91 612 73 04 email pvgspain zibro com PVG France SARL 4 Rue Jean Sib lius B P 185 76410 SOTTEVILLE SOUS LE VAL tel 33 2 32 9607 47 fax 33 0 820 34 64 84 email pvgfrance zibro com Appliance Finland Oy Piispantilankuja 6C 02240 ESPOO tel 358 9 4390 030 fax 358 9 4390 0320 email appliance appliance group com Scott Brothers Ltd The Old Barn Holly House Estate Cranage Middlewich CW10 9LT UK tel 44 1606 837787 fax 44 1606 837757 email sales scottmail co uk PVG Italy SRL Via Niccol Copernico 5 50051 CASTELFIORENTINO F1 tel 39 571 628 500 fax 39 571 628 504 email pvgitaly zibro com Appliance Norge AS Vogellunden 31 1394 NESBRU tel 47 667 76 200 fax 47 667 76 201 email appliance appliance group com PVG International B V P O Box 96 5340 AB OSS tel 31 412 694 694 fax 31 412 622 893 email pvgnl zibro com Gardena Lda Recta da Granja do Marqu s ALGUEIRAO 2725 596 MEM MARTINS tel 35 21 92 28 530 fax 35 21 92 28 536 email pvgint zibro com PVG Polska Sp z o o ul Koscielna 110 26 800 Biatobrzegi tel 48 48 613 00 70 fax 48 48 613 00 70 email pvgpoland zibro com Appliance S
20. weden AB Sj gatan 6 25225 HELSINGBORG tel 46 42 287 830 fax 46 42 145 890 email appliance appliance group com PVG Isitma Klima So utma Ltd Sti Atat rk Cad No 380 Ak Ishani Kat 6 35220 Alsancak IZMIR TURKEY tel 90 232 463 33 72 fax 90 232 463 69 91 email pvgturkey zibro com Printed in Japan 7818001921 man_SRE188E avg 060718 PVG Traffic
Download Pdf Manuals
Related Search