Product Manual
Contents
1. Software Function DOS Win 3 1 95 2000 X NT 2000 XP CE Linux QNX p Standard Calibration o o e em e 6 em em e Advanced Calibration em e em e Multiple Monitors e Multi Device G on S Rotation o em e e Stream Point mode on on Drawing mode o e em e on e Beep Sound o e em e on on Beep sound adjustable on on Wake up function e a Showing linearity on e Right button o e en e em em e Hide cursor 6 e e Double click area and id speed adjustable About e e en e em e HS 232 Interface 9000 series USB Interface 5000 series ADP 1224A User Manual 32 5 2 Software Function Description Description for each of the software functions shown in the table above follows Standard Calibration The Standard Calibration function lets you match the touch screen to your display so that the point you touch is accurately tracked on screen Standard calibration only requires four points for calibration and one point for confirmation Under normal circumstances Standard Calibration is all you need to perform an accurate calibration Advanced Calibration The Advanced Calibration function improves the accuracy of calibration by using more involved engineering calculations Use this function only if you have tried the Standard Calibration and there is still a discrepancy in the way the touch screen maps to the display You can choose 4 9 16 or 25 point2. 1 Getting into Burn in Mode Before setting into a burn in mode first disconnect the AC power cord Then press don t let them go the W A buttons until the AC power cord is connected and the RGB appears on the top left corner of your screen Now it can be put into the burn in mode for changing colors 2 Getting Out of Burn in Mode Before getting out of the burn in mode please first disconnect the AC power cord Then press the x button If not workable press the A button and don t let them go until the AC power cord is connected Please don t let your fingers go until the AC power cord is connected again and the wording of RGB appears on the top left corner of your screen and wait for 3 seconds Under the non signal entry situation if is seen exit is thus successfully made ADP 1224A User Manual 9 2 2 OSD Controls To make any adjustment select the following 1 Press B Menu to show the OSD menu or disable the OSD menu 2 Select the icon that you wish to adjust with the NA or key in the menu 3 Press E Menu and then choose the item with the NA or key 4 Press B Menu and then adjust the quality with the NA or key 1 Ifthe RGB is still on the top left corner of the screen press B to enter Miscellaneous and choose Reset and then Yes and press BII When the screen goes black disconnect power and repeat the above steps 2 If the RGB is not found dis
3. The PenMount DMC9000 is the best performance touch screen controller Designed with PnP features for new system trends it offers RS 232 touch screen interface The DMC9000 is designed for those who need an all in one solution with a built in A D converter for a denser total printed circuit board in Electrical Specifications Touch Screen 4 5 amp 8 wire Package 28 pin PDIP or 32 pin TQFP Communications RS 232 Characteristics 8 bit RISC microprocessor with built in functions including 10 bit ADC UART Timer Counter Comparator Watchdog Memory etc Voltage Range 4 0V to 6 0V Power Consumption Active 3 4 mA Idle Mode 1 4mA at 4 MHz 3V Power Down Mode 1 uA Operating Temperature 40 C to 85 C Storage Temperature 65 C to 150 C Volt on RESET with respect 1 0V to 13 0V to Ground DC Current per I O Pin 40 0 mA DC Current Vcc and GND Pins 300 0 mA Driver Software DOS Windows 3 11 Windows 95 2000 XP Windows NT 2000 XP Linux QNX Windows CE for both X86 and SA CPUs ADP 1224A User Manual 41
4. 1 3 n i ADP 1224A User Manual 12 2 4 AD Board VA 3600 OSD Functions 2 Getting into Burn in Mode Before setting into a burn in mode first disconnect the AC power cord Then press don t let them go the W A buttons until the AC power cord is connected and the RGB appears on the top left corner of your screen Now it can be put into the burn in mode for changing colors 2 Getting Out of Burn in Mode Before getting out of the burn in mode please first disconnect the AC power cord Then press the x button If not workable press the A button and don t let them go until the AC power cord is connected Please don t let your fingers go until the AC power cord is connected again and the wording of RGB appears on the top left corner of your screen and wait for 3 second Under the non signal entry situation if is seen exit is thus successfully made When the Burn in Mode is Unable to Eradicate 4 lf the RGB is still on the top left corner of the screen press B to enter Miscellaneous and choose Reset and then Yes and press Li When the screen goes black disconnect power and repeat the above steps 5 If the RGB is not found disconnect the AC power cord first Then press the Y A buttons don t let them go until the AC power cord is connected and wait for 2 to 3 seconds When RGB appears repeat the above steps 6 Functions of OSD Keys Auto Adjust Up Left Do
5. Multiple Monitors Multiple Monitors support from two to six touch screen displays for one system The PenMount drivers for Windows 2000 XP support Multiple Monitors This function supports from two to six touch screen displays for one system Each monitor requires its own PenMount touch screen control board either installed inside the display or in a central unit The PenMount control boards must be connected to the computer COM ports via the RS 232 interface Driver installation procedures are the same as for a single monitor Multiple Monitors support the following modes Windows Extends Monitor Function Matrox DualHead Multi Screen Function nVidia nView Function NOTE The Multiple Monitor function is for use with multiple displays only Do not use this function if you have only one touch screen display Please note once you turn on this function the rotating function is disabled ADP 1224A User Manual 25 Enable the multiple display function as follows 1 Check the Enable Multiple Monitor Support box then click Map Touch Screens to assign touch controllers to displays di PenMount Control Panel DK Calibrate Draw Multiple Monitors Option About w Enable Multiple Monitor Support 2 When the mapping screen message appears click OK PI DenMount Control Panel PIE Calibrate Draw Multiple Monitors Option About Enable Multiple Monitor Support Mapping Please touch the panel as indicate
6. if the PenMount driver provides an Advance Calibration function when touch screens age their touch linearity declines This non linearity is apparent when the touched point on the touch screen is not the same as the point on the display The plot calibration data function shows the linearity status of the touch screen This is only a support function for the user The exact linearity of a touch screen requires a linearity test machine ADP 1224A User Manual 38 Right Button The Right Button function simulates the right button function of a mouse Click the right button and the user can only touch the screen once and the driver changes the touch definition to the left button Hide Cursor The Hide Cursor function keeps the cursor arrow and other cursor symbols from appearing when using the touch screen The cursor appears when the user turns this function off Cursor Offset The Cursor Offset function lets the user adjust the position of the touch point to a desired location away from the real touch point Double Click Area and Speed The Double Click Area and Speed function lets the user adjust the double click area and speed to their personal preference About This option shows the exact version of the drivers and controller firmware Updated drivers are available for download on the PenMount website ADP 1224A User Manual 39 Appendix A Board Descriptions amp Specifications This appendix provides information on controller boar
7. required to take whatever measures may be required to correct the interference Electric Shock Hazard Do not operate the machine with its back cover removed There are dangerous high voltages inside Disclaimer This information in this document is subject to change without notice In no event shall Aplex Technology Inc be liable for damages of any kind whether incidental or consequential arising from either the use or misuse of information in this document or in any related materials ADP 1224A User Manual 2 Table of Contents Windsor 2 RIL aT EET EE 2 Chapter 1 Getting Started Me e E ES 12 DIMENSION Str ii n 6 Ueog zii M DESsciploN iis lean 7 LA ISNA Nocerino AER 8 Chapter 2 OSD 2 1 Front Panel ControlS ccc ccc cece ce ccecccuccuceucceueeucceuuaesaneas 9 22 OSO Consacrata 10 EA R L E A 11 2 4 AD Board VA 3600 OSD FUNCtions i 13 Chapter 3 Control Board 3 1 Introduction to PenMount Control Board esee 14 A ausak ube beside ee Debut uie E Fora unb tug Cumt 15 3 3 Electrical ele eneel eTn ccc cece cece ence cece ee ee ee eee esse eeaee eee 15 3 4 Installation of Control Board eene 16 Chapter 4 Installation 4 1 Windows 2000 XP Driver Installation eese 17 4 2 Configuring PenMount Windows 2000 XP Driver 21 4 3 Uninstall PenM
8. DMC3000 and DMC9100 Driver Version 401 Firmware Version 41 20 COM 19200bps MX 4 m 1 re Tat 00806057 i t t 4 1f i IET il IM Qd l ILS I T LL e TI 78 I L2 LL i E mail salt salt com tw Website www salt corn tu Copyright C 2003 Salt Int l Corp PenMount Monitor Menu Icon The PenMount monitor icon PM appears in the menu bar of Windows 2000 XP system when you turn on the PenMount Monitor in the PenMount Utilities pm 4 04 PM The PenMount Monitor has the following functions Control Panel Right Button Pen Stabilizer I I Exit e lt ADP 1224A User Manual 28 Turns beep on or off Right Button Pen Stabilizer ADP 1224A User Manual When you select this function a mouse icon appears in the right bottom of the screen Click this icon to switch between Right and Left Button functions a a Check this function to reduce cursor vibration for relatively unstable touch screens or where there may be excess vibration Normally this function is not checked Exits the PenMount Monitor function 29 PenMount Rotation Functions The PenMount driver for Windows 2000 XP supports several display rotating software packages The PenMount drivers for Windows 95 Windows 2000 XP Windows 2000 XP as well as Windows 98 USB and Windows Me 2000 XP support display rotating software packages such as e Portraits Pivot Screen Rotation Software e ATI Displ
9. IndustrialiComputing Productsyandisenvices Embedding the future Why Choose DSL Our Services VA Lifetime technical support E E Y Electronic Design d Fully customisable products J Production Management VA Product branding bezel colours company logos ff Assembly and test i Free pre installation of OS and your software VA Bespoke BIOS creation K 5 sales dsl Itd co uk or call us on 44 0 1462 675530 DSL Ltd 4 Aylesford Court Works Road Letchworth Garden City Hertfordshire SG6 1LP WAPLEX ADP 1224A Display User Manual Revision Version Bema 2012 Aplex Technology Inc All Rights Reserved Published in Taiwan Aplex Technology Inc 15F 1 No 186 Jian Yi Road Zhonghe District New Taipei City 235 Taiwan Tel 886 2 82262881 Fax 886 2 82262883 E mail aplex aplex com tw URL www aplex com tw ADP 1224A User Manual 1 Warning This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual it may cause interference to radio communications It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be
10. OZJEOCIHOEZIECZ IECOIHULEZ EJE Aca lll OHP H honnnannannannannan M dK dU JA JL RM L AA dU JM dL A 337 0 4 8 8 339 4 342 4 a B ani 00000800000 Figure 1 1 Dimensions of the ADP 1224A nomnnaonrn 0000000 HEEE FIEF E z 069 069 Lo nBgbemagpdgadmgu t DIDO DI OZ 10010000000 dT TTT h TT Ae 30010040040 id Ae ADP 1224A User Manual 1 3 Brief Description of the ADP 1224A The ADP 1224A is a 21 5 TFT LCD Display that comes with viewing angle of 170 H degrees and 160 V degrees and more outstanding features thus giving you the best in monitoring and control applications The front panel of the display is sealed IP65 rating when it is VESA mounted in a NEMA rated cabinet or enclosure It is optional to be equipped with a resistive touch screen Figure 1 2 Front View of the ADP 1224A Figure 1 3 Rear View of the ADP 1224A ADP 1224A User Manual 1 4 Display Mode Display Mode Hori Eu KHz Vert Sync Hz VGA 640 x 480 RE 1280 x 1024 79 Full HD 1920x1080 HF o SXGA ADP 1224A User Manual 8 Chapter 2 2 1 Front Panel OSD Functions Auto Adjust Up Left Down Right Power Menu Entry Power Indicator O Power switch To turn ON or OFF the power Y Shift the icon to the right side or shift it up Shift the icon to the left side or shift it down J Menu To enter OSD menu for related icon and item A gt Auto Button One touch auto adjustment
11. ay Driver Rotating Function e nVidia Display Driver Rotating Function e SMI Display Driver Rotating Function e Intel 845G GE Display Driver Rotating Function Configuring the Rotation Function 1 Install the rotation software package 2 Choose the rotating function 0 90 180 2709 in the 3 party software The calibration screen appears automatically Touch this point and rotation is mapped Please touch the point N md NOTE The rotating function is disabled if you use Monitor Mapping ADP 1224A User Manual 30 4 3 Uninstall the PenMount Windows 2000 XP Driver 1 Exit the PenMount monitor PM in the menu bar 2 Go to Settings then Control Panel and then click Add Remove program Select PenMount DMC9000 and click the Add Remove button L Ma Curent tlt gn pe E penipet peranna sed pra nn Oed bha ef agpi Ke SPS gt C toos Hle tope fev ye comme car dA Ben 4 Select Yes and Close to remove the PenMount Windows 2000 XP driver and reboot the system ADP 1224A User Manual 31 Chapter 5 5 1 Software Functions This chapter describes the special software functions that configure and adjust the PenMount controller board and touch screen hardware Please note that not all of the functions are available for every driver Software functions and their availability for specific interface and systems are shown in the table below a description for each function follows
12. connect the AC power cord first Then press the Va A buttons don t let them go until the AC power cord is connected and wait for 2 to 3 seconds When RGB appears repeat the above steps 3 Functions of OSD Keys ADP 1224A User Manual 10 2 3 Main Menu Color image Setting Position OSD Menu Language Misc Exit Ver 1 3 Contrast Brightness Color Adjust Color Temp Back Ver 1 3 Clock Phase Gamma Shar press Hach ADP 1224A User Manual In the Main menu there are the following items e Color Image Setting Position OSD Menu Language Misc Exit For Color check out the following Contrast Brightness Color Adjust Color Temp e 9 e Back For Image setting check out the following e Clock Phase Gamma Sharpness e e o Back 11 Ver 1 3 In the Position there are the following Q LD Position e H Position k ij V Position T e V Position e Back Ww Hack In the OSD menu there are e OSD H Pos e OSD V Pos e OSD Timer o Back In the Language menu there are e English Frances Germany Spanish Traditional Chinese simplified Chinese Japanese Ver 1 3 English Fran ais Deutsch Espanol Ky ears In the Misc menu there are Signal Source rel EI Select VGA Analogue VGA Input 5 R Select DVI Digital DVI D Input select AV Composite Video Input Select SV S Video Video Input o Reset e Back Ver
13. d features and specifications PenMount 9036 Control Board The PenMount 9036 control board is configured for the RS 232 interface and it supports 4 wire 5 wire and 8 wire touch screens PenMount 9036 Features e DMC9000 touch controller e Diagnostic LED on board e Supports PnP and non PnP mode e Supports 4 wire 5 wire and 8 wire touch screen e Baud rate 19200 or 9600 bps selectable e Automatic pin assignment adjustment e Input voltage is 5V to 12V e Bundled with PenMount drivers which are also available for download from our website Connector Pin Definitions Pin definitions for the two connectors on the PenMount 9036 control board follow Connector Pin Definitions for Touch Screen Pin definition 4 wire 5 wire 8 wire wires touch screen touch screen touch screen PIN 9 N A N A Right Sense PIN 8 N A N A Left Sense PIN 7 N A N A Bottom Sense PIN 6 N A Sense Top Sense PIN 5 Right LR Right PIN 4 Left LL Left PIN 3 Bottom UR Bottom PIN 2 Top UL Top PIN 1 Ground Ground Ground Connector Pin Definitions for Power and RS 232 Power Lines RS 232 Interface Pin PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 Definition Ground 5V 12V power RTS TXD RXD Ground ADP 1224A User Manual Appendix B Controller IC Specifications This appendix offers information on touch screen controller IC features and specs PenMount DMC9000 Touch Screen Controller IC
14. d in the Following screens ADP 1224A User Manual 26 3 4 NOTES Touch each screen as it displays Please touch this monitor Following this sequence and touching each screen is called mapping the touch screens Touching all screens completes the mapping and the desktop reappears on the monitors Select a display and execute the Calibration function A message to start calibration appears Click OK Calibrate To start calibration please touch the panel to calibrate in the following screen ww Touch this screen to start its calibration appears on one of the screens Touch the Screen Touch the red square messages appear Touch the red squares in sequence Continue calibration for each monitor by clicking Standard Calibration and touching the red squares 1 If you use a single VGA output for multiple monitors please do not use the Multiple Monitor function Just follow the regular procedure for calibration on each of your desktop monitors 2 he Rotating function is disabled if you use the Multiple Monitor function 3 If you change the resolution of display or screen address you have to redo Map Touch Screens so the system understands where the displays are ADP 1224A User Manual P About This panel displays information about the PenMount controller and this driver version I PenMount Control Panel lE Calibrate Draw Multiple Monitors Option About PenMount
15. d you to reboot your computer to enable al the Functions ADP 1224A User Manual 4 2 Configuring the PenMount Windows 2000 XP Driver Upon rebooting the computer automatically finds the new 9036 controller board The touch screen is connected but not calibrated Follow the procedures below to carry out calibration 1 After installation click the PenMount Monitor icon PM in the menu bar 2 When the PenMount Control Panel appears click Calibrate PenMount Control Panel The functions of the PenMount Control Panel are Calibrate Draw Multiple Monitors Option and About which are explained in the following sections Calibrate This function offers two ways to calibrate your touch screen Standard Calibration adjusts most touch screens Advanced Calibration adjusts aging touch screens Standard Calibration Click this button and arrows appear pointing to red squares Use your finger or stylus to touch the red squares in sequence After the fifth red point calibration is complete To skip press ESC Advanced Calibration Advanced Calibration uses 4 9 16 or 25 points to effectively calibrate touch panel linearity of aged touch screens Click this button and touch the red squares in sequence with a stylus To skip press ESC C PenMount Control Panel ok Calibrate Draw Multiple Monitors Option About Advanced Mode 3 Plot calibration data Standard Calibration Ad
16. ds and inquire about operation and usability issues Note Before you can use multiple monitors you need to map each monitor Multiple Devices The Multiple Devices function is designed to let you use two or more monitors to display the same image Software that supports this function includes the PenMount 9000 2000 XP drivers and the PenMount 5000 2000 XP 2000 XP CE drivers The drivers for PenMount 9000 can support up to six control boards and the drivers for PenMount 5000 support up to 16 Comparing Functions The difference between the Multiple Monitors function and the Multiple Devices function are illustrated below A B or A B The Multiple Monitors function shown above extends the screen into 2 or more monitors ADP 1224A User Manual 34 A B The Multiple Devices function displays the same image on two or more monitors Requirements Before using the Multiple Monitors function you need the following 1 A display card that supports Dual Monitors such as the Matrox nVidia ATI etc or that outputs into a 1 into 2 VGA signal box 2 Two or more touch screens Two or more serial ports or USB ports 4 Two or more PenMount 9000 control boards such as the 9036 9026 9084 or 90A4 or PenMount 5000 control boards such as the 5184 or 51A5 5 If using the PenMount 9000 control board the driver must be the PenMount 9000 Windows 2000 XP v4 01 or greater software driver 6 If using the PenMount 5000 control board the drive
17. e software automaticaly Recommended Install trom a let or specilic location Advanced Click Next to continue Met Cancel ADP 1224A User Manual 17 2 Insert the PenMount Driver CD ROM Go to the Windows 2000 XP Driver folder Click setup exe Windows XIDO XP Driver Y4 D1 co EX iis Fevortes To Hep Oa O 5s frese F Tie and Folder Tasks ie Atl nw E Mau tha fia agis dans de Y ode eodem e Pana bow f x w Hr fio Hither Places c PZW cd My Scour 9 Paci cet 3 Wy Tp ler 4 Muro KT acs 3 The screen displays the installation wizard for the PenMount software Click Next T PenMount DMC9000 and DMC9100 InstaliShield Wizard Welcome to the InstallShield Wizard for PenMount DMC9000 and DMC9100 The Installshield P Wizard wil install Pen iount DI CS020 and DMC9100 on your computer To continue cick Next ADP 1224A User Manual 4 ALicense Agreement appears Click I accept and Next 5 The Ready to Install the Program screen appears Select Install ADP 1224A User Manual i PenMount DMC9000 and DMC9100 InstallShield Wizard License Agreement Please read the following license agreement carefully oftware License Copynght C Salt International Corp All nght reserved enldount Utilities drivers include DOS Windows 3 11 Windows 95 Windows 98 Windows ME Windows NT indows 2000 Windows XP Windows CE Linux and Onx dri
18. itch on the upper right of the image above see Figure 3 1 This switch selects baud rate PnP or non PnP mode and touch screen type Set the DIP switch to configure your control board according to the definitions and settings of the table below OFF Baud Rate Adjustment 9600 19200 6 Turn on power to the computer and the display 7 Install the software drivers and utilities and calibrate the touch screen ADP 1224A User Manual 16 Chapter 4 4 1 Windows 2000 XP Driver Installation for 9036 Control Board Before installing the Windows 2000 XP driver software you must have the Windows 2000 XP system installed and running on your computer You must also have the 9036 PenMount Serial Interface controller board installed Contents of the PenMount Windows 2000 XP driver folder are listed below DMC9000 inf DMC9000 sys DMC9000 cat SETUP EXE lf you have an older version of the PenMount Windows 2000 XP driver installed in your system please remove it first Follow the steps below to install the PenMount Windows 2000 XP driver 1 When the system first detects the controller board a screen appears that shows Unknown Device Do not use this hardware wizard Press Cancel Found New Hardware Wizard Welcome to the Found New Hardware Wizard This weard helps you install software For Urknown M your hardware came with an installation CD 22 or floppy disk insert it now What do you want Ihe weard lo do C Install th
19. ount Windows 2000 XP Driver ii 31 Chapter 5 Software 5 1 Software FUNCIONS si iia 32 5 2 Software Function Descriptions e eee eeeeeeeeeeeeaeeeeens 33 ADP 1224A User Manual 3 Appendix A Board Description Specifications 40 Appendix B Controller IC Specifications 41 Figures LL Figure 1 1 Dimensions of ADP 1224A Li 6 Figure 1 2 Front View of ADP 1224A i 7 Figure 1 3 Rear View of ADP 1224A i 7 Figure 3 1 Bird Eye s View of Control Board 14 Figure 3 2 Mechanical Drawing of Control Board 14 ADP 1224A User Manual Chapter 1 1 1 Specifications Model No ADP 1224A External I O Port e Default VGA Input AC 100 240V input Optional DVI Video S Video Touch I O 3 Pin terminal block DC11 32V input Touch Screen Type Light Transmission Optional Resistive Type 80 Power Supply Power Input AC 100 240V input Optional for DC 11 32V Construction Steel Housing IP Rating Front Panel IP65 Mounting VESA 100x100 Mount Dimensions WxHxD 557 W x362 H x68 D mm Environmental Operating Temperature Storage Temperature 0 50 C 20 60 C 10 9096 40 C non condensing Meet CE FCC Class A Storage Humidity Certificate ADP 1224A User Manual IMENSIONS 1 2 D 4442 H
20. r must be for Windows 2000 XP 2000 XP CE 9000 Control Boards To use multiple devices with 9000 Control Boards 1 Configure your computer hardware 2 Attach each 9000 Control Board to a different computer s serial port 3 Install the appropriate PenMount software driver in each computer 4 Use each driver s Calibration function to calibrate each computer s touch screen You must calibrate each touch screen before configuration is complete Rotation There are currently a number of software packages on the market that support rotating monitors 0 90 180 and 270 However you will not be able to use a touch screen unless it is matched to the appropriate rotation Our rotation configuration function allows you to easily match the touch screen when you rotate your monitor If you use a rotating monitor you will need a display card such as from nVidia Intel SMI or ATI and software such as Portrait Pivot Pro For software operation and features please refer to your software manual Configuring the rotation function is easy Select this option and a point appears for you ADP 1224A User Manual 35 to touch Once the point is touched the software driver understands which degree you plan to rotate your display The rotation function supports 90 180 and 2 70 degrees rotation 0 degrees ADP 1224A User Manual 36 ADP 1224A User Manual 90 degrees 180 degrees 270 degrees 2d Stream Point Mode St
21. ream and point modes control the touch and drag function of the touch screen The point mode only allows touch interaction with the screen and does not allow the user to drag objects The point mode is useful for maintaining the location of screen icons such on POS terminals The stream mode allows a user to touch and drag icons and other items around on the screen similar to using a mouse Drawing Mode Drawing mode is a utility that lets the user draw on the screen using a finger or stylus This allows the user to test the touch screen and touch controller to see if it is operational or is mapped correctly The drawing mode can display either the matrix address of points touched or just show lines drawn One of the PenMount driver s strengths is a special mathematical algorithm that minimizes the occurrence of noise and smooths the drawing of lines Beep Sound All of PenMount s drivers support the beep sound function however some PC systems may only offer a fixed buzzer sound Beep Sound Adjustable software drivers for Windows systems let the user adjust the frequency and length of the beep sound The drivers let the user adjust the desired touch screen sound as well as turn the sound off Wake Up Function The Wake Up function lets the user touch the screen and wake the system up from suspend mode Point Calibration Data The Plot Calibration Data function displays the touch screen linearity map which is available
22. s to calibrate though we suggest that you first try 9 points if it is still not tracking well then try 16 or 25 points The more points you use for calibration the greater the accuracy Errors in calibration may occur due to viewing angle or individual skill and there may be little difference in using 16 or 25 points Note that a stylus is recommended for the most accurate results Multiple Monitors Until now most touch screen systems only support one monitor and users of multiple monitors have not been able to use touch screen systems This situation has inspired PenMount to design and develop Multiple Monitors support using the PenMount 9036 control board and Windows 2000 XP driver Our advanced design supports from 2 to 6 monitors that can be split horizontally or vertically Requirements Before using the Multiple Monitor function you need the following 1 Adisplay card that supports multiple monitors such as the Matrox nVidia ATI etc Two or more display cards supported by Windows are also OK 2 Two or more touch screens Two or more serial ports 4 Two or more PenMount 9000 control boards such as the 9036 9026 9084 or 90A4 5 The PenMount 9000 Windows 2000 XP v4 01 or greater software driver co Before using Multiple Monitors you must have two or more monitors that are in extension mode For display cards that support multiple monitors we suggest you consider Matrox ADP 1224A User Manual 33 nVidia or ATI car
23. tive type Touch Screen Controller DMC9000 Communications RS 232 Baud Rate 19200 and 9600 baud rate selection Resolution 1024x1024 10 bit A D converter inside Power Input 5V 12V DC Power Consumption 12V 24mA i where i v touch screen sheet R 5V 20mA i where i v touch screen sheet R ADP 1224A User Manual 15 Board Size 6 0 x 2 5cm Portrait Support 90 to 279 screen rotation Static Protection ESD device optional 3 4 Installation of the 9036 Controller Board Follow the steps below to install the 9036 control board 1 Power down your computer and display and open your display or system case Find space on your system and attach the control board to your system with screws The control board has industry standard 3 screw holes 2 Find the white 6 pin right angle connector on the left in the image above see Figure 3 1 The power cable is pin 1 and pin 2 Solder the power and ground wire to the system The RS 232 cable is for pins 3 to 6 Attach the RS 232 cable s D sub connector to a COM port at the back of the computer 3 Find the white 9 pin right angle connector on the right in the image above see Figure 3 1 Attach the female end of the touch screen cable to this connector If you attach the cable of a 4 5 8 wire touch screen to pins 1 5 1 6 1 9 attach the male end of the cable to the touch screen tail 4 Mount your touch screen to the display 5 Find the onboard DIP sw
24. vanced Calibration ADP 1224A User Manual 21 NOTE The older the touch screen is the more Advanced Mode calibration points you need for an accurate calibration Use a stylus during Advanced Calibration for greater accuracy dy PenMount Control Panel Sle Calibrate Draw Multiple Monitors Option About Advanced Mode E iw Plot calibration data Advanced Calibration ADP 1224A User Manual DI Plot Calibration Data Check this function and a touch panel linearity comparison graph appears when you have finished Advanced Calibration The blue lines show linearity before calibration and black lines show linearity after calibration m PenMount Control Panel lE Calibrate Draw Multiple Monitors Option About Advanced Mode E iw Plot calibration data Standard Calibration ADP 1224A User Manual 23 Draw Tests or demonstrates the PenMount touch screen operation The display shows touch location Click Draw to start Touch the screen with your finger or a stylus and the drawing screen will register touch activity such as left right up down pen up and pen down I PenMount Control Panel a S ES Calibrate Draw Multiple Monitors Option About Touch the screen with your finger or a stylus and the drawing screen will register touch activity such as left right up down pen up and pen down ADP 1224A User Manual 24 Click Clear Screen to clear the drawing
25. vers o copy modify or translate ts prohibited except with Sall s nien consents o license PenMount Utilities drivers contact Salt International Corp Emad salt salt com tw Ottie page www salt com tw 1 accept the terms in the license agreement O1 do not accept the terms in the license agreement Insta hred TTE i PenMount DMC9000 and DMC9100 InstallShield Wizard Ready to Install the Program The wiard is ready to begin installation Click Instal to begin the installation If you want to review or change any of your installation settings click Back Click Cancel to ext the wizard 19 6 The next screen is Hardware Installation Select Continue Anyway Hardware Installation The software you are installing for this hardware PenMount DMCSOO0 and DMC9100 has not passed Windows Logo testing to venty its compatibdity Tel iw thi AR el with Windows XP Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing STOP Installation 7 The InstallShield Wizard Completed appears Click Finish InstallShield Wizard Completed The InstalShield Wizard has successfully instaled Perfhiount DMC9000 and DIACS100 Click Finish to exit the wiard We recommen
26. wn Right Power E Menu Entry Power Indicator ADP 1224A User Manual 13 Chapter 3 3 1 Introduction to the PenMount 9036 Controller Board The PenMount 9036 control board is configured for use with the RS 232 interface It connects to the touch screen power supply and computer system s RS 232 port and supports 4 5 and 8 wire touch screens The control board has some advanced functions such as PnP and non PnP mode adjustable baud rate thus making easy for customers to select different touch screens without changing the control board The size of the board is 26 by 60mm and it has two connectors and one dipswitch on board Figure 3 1 Bird s Eye View of PenMount 9036 60 0 3 96 ME 23 0 3 38 Figure 3 2 Mechanical Drawing of PenMount 9036 ADP 1224A User Manual 14 3 2 Features RS 232 interface Touch controller is DMC9000 Design for the best touch performance and easy configuration PnP or Non PnP mode selectable Design for best cost arrangement Supporting 2048x2048 pen device resolution 19200 or 9600 baud rate transmission selectable Upgraded noise handling mechanism 3 level scheme Fixed and high speed sampling rate 4 5 and 8 wire touch screen supported Touch screen cable RS 232 with power cable connectors onboard 5V to 12V power input Circuit protection for input voltage Touch activated LED indicator onboard 3 3 Electrical Specifications Touch Screen 4 5 and 8 wire analog resis
Download Pdf Manuals
Related Search