INSTALLATION GUIDE - Mitsubishi Electric Australia
Contents
1. Wi Fi CONTROL MITSUBISHI ELECTRIC Setting information MAC 558IF E address MAC MAC 558IF E serial number ID MAC 558IF E code PIN Indoor unit model name Indoor unit serial number Outdoor unit model name Outdoor unit serial number System commissioning date MAC 558IF E installation date Wi Fi Control minimum reguirements for operation e Compatible WPS router capable of WPA2 AES encryption The wireless network coverage must include the heat pump installation location e A PC or Tablet Smartphone that is iOS Android compatible e A compatible Mitsubishi Electric Heat Pump with a MAC 558IF E Adaptor Mitsubishi Electric Wi Fi Heat Pump Control Important Note Before carrying out installation of the MAC 55SIF E adaptor please read the safety instructions listed on page 8 of this installation guide Register Your Heat Pump s Thank you for choosing a Mitsubishi Electric Heat Pump with Wi Fi Control Once your adaptor is installed either download the app search term Mitsubishi Electric or visit our website to register your heat pump s ANDROID APP ON 7 Download on the Google play E App Store Once registered you will be able to control your heat pump with your smartphone tablet or online using an internet connection for a list of compatible devices please visit the Mitsubishi Electric website User Manual A copy of the user manual terms amp2. conditions and privacy policy can be downloaded at any time from the Mitsubishi Electric website Mitsubishi Electric New Zealand www mitsubishi electric co nz wifi Phone 0800 639 434 Mitsubishi Electric Australia www mitsubishielectric com au wifi Phone 02 9684 7777 Wi Fi Control Installation Instructions Information for installers The following steps explain how to connect the MAC 558IF E Adaptor to a Mitsubishi Electric Heat Pump EQUIPMENT REQUIRED FOR INSTALL MAC 558IF WPS Enabled Wi Fi Tools to remove Adaptor Router Installation cover of indoor Guide unit Wi Fi CONTROL Important Note Before going to the users home ensure they have a WPS capable router and WPA2 AES encryption can be set For ease of access please do not install the Wi Fi Adaptor inside high wall indoor unit cabinets Record the adaptor s MAC ID Isolate the outdoor unit and verify number and serial numbers on page power has been disconnected from 2 of the Wi Fi Installation Guide the complete system Remove the cover of the indoor unit the cable terminal and the cover to the control board Run the cables down the back of the unit with the other cables Tuck cabling away and secure EGISET Wi Fi INTERFACE ACCLRRRIF E Pe Check that the MAC 558IF E Adaptor is flashing The install has now been completed Locate the CN105 port on the main control board and connect the MAC
3. orange LED 2 light up this is an indication that there is a problem with the router communicating with the adaptor If this occurs you may need to check the following WPS is working on your router Signal is reaching the adaptor DHCP addresses are available Your router is compatible with the adaptor For a list of compatible routers or if you are still experiencing issues connecting your router to the Wi Fi Adaptor please contact your local Mitsubishi Electric Office as listed on the back cover of this guide Main causes that WPS failed are as follows Communication distance from the Wi Fi Adaptor to access point access point settings encryption authentication limit of connections etc Refer to the router s instruction manual for more information Switch Function 1 WPS switch The WPS switch is used for pairing the Wi Fi Adaptor with the access point There are two types of WPS push button configuration WPS Push and PIN code method WPS PIN WPS Push Hold down the WPS switch for 2 seconds to start WPS Push pairing When WPS Push is enabled on the Wi Fi Adaptor LED1 starts flashing green 0 5 sec interval and the pairing can be completed by enabling WPS Push on the access point e WPS PIN Hold down the WPS switch for 15 seconds to start WPS PIN pairing When WPS PIN is enabled on the Wi Fi Adaptor LED1 starts flashing green 0 2 sec interval and the pairing can be completed by enabling WPS PIN on the
4. setting before before commencement of the installation of commencement of the installation of the MAC 558IF E MEE e he MAC 558IF E should not be installed To complete connection of the and connected to any Mitsubishi Electric MAC 558IF E to the Wi Fi service physical system which is to provide cooling or access to the access point may be required heating to critical applications Details of the heat pump and MAC 558IF E can be recorded on page 2 Setting Information Mitsubishi Electric s Wi Fi Adaptor is designed for communication to Mitsubishi Electric s Wi Fi service Third party Wi Fi Adaptors cannot connect to Mitsubishi Electric s Wi Fi service Mitsubishi Electric is not responsible for any i under performance of a system or any product ii system or product fault or iii loss or damage to any system or product which is caused by or arises from connection to and or use of any third party Wi Fi Adaptor or any third party Wi Fi service with Mitsubishi Electric equipment For the latest information regarding Wi Fi Control New Zealand based enquiries please visit www mitsubishi electric co nz wifi Australian based enquiries please visit www mitsubishielectric com au wifi Product Introduction WPS switch Activates WPS RESET switch Resets the system and ALL settings LED1 Green Shows the wireless communication state LED2 Orange Shows the MAC 558IF E state LED3 Green Shows the local communicatio
5. 558IF E Adaptor Reassemble the indoor unit and restore power to the system 3 LINEI ST The adaptor is now able to be Connected to the user s router Steps for this are shown on the following pages Please note the above illustrates high wall unit installation Installation will vary depending on indoor model type Wi Fi Control Installation Instructions Information for users The following steps explain how to connect the MAC 558IF E Adaptor to a router KEY LED LIGHTS e ON o OFF x FLASHING Check Wi Fi and WPS are enabled Activate WPS mode on your router on your router The connection This will be enabled for a set procedure varies depending on period allowing approximately two minutes to complete Step 3 To do so please refer to your router s manual your router refer to your router manual for more information Please Note The WPS and router reset buttons may be similar on some routers Please exercise caution as resetting your router will IN erase network configuration N Y Activate WPS on your adaptor by using a small object to press and hold the WPS button for two seconds CC re 9 MITSUBISHI A ELECTRIC Turn the adaptor over and check LED 1 top light is flashing 4 MITSUBISHI A ELECTRIC Next the bottom light LED 3 will start flashing as it connects to the internet This may continue for u
6. access point Before using WPS PIN the PIN code of the Wi Fi Adaptor needs to be set on the access point This product is only compatible with the access point that supports WPS 2 RESET switch Hold down the RESET switch for 2 seconds to reboot the system Hold down the RESET switch for 15 seconds to initialize the Wi Fi Adaptor to the factory default When the Wi Fi Adaptor is reset to the factory default ALL the configuration information will be lost Take great care in implementing this operation Specifications Input Voltage DC12 7V from indoor unit Power consumption MAX 2W Size WxHxD mm 88x49x18 5 Weight 105g including cable RF channel 1ch 13ch Radio protocol IEEE 802 1 1 20 Encryption AES Authentication PSK 1 1 MITSUBISHI ELECTRIC Contact Details Mitsubishi Electric New Zealand Mitsubishi Electric Australia www mitsubishi electric co nz wifi www mitsubishielectric com au wifi WELLINGTON SYDNEY HEAD OFFICE HEAD OFFICE 1 Parliament Street 348 Victoria Road PO Box 30772 Rydalmere Lower Hutt 5040 NSW 2116 Phone 0800 639 434 Phone 02 9684 7777 Fax 04 560 9133 Fax 02 9898 0484 Helpline opening hours 8 30am 5 00pm weekdays
7. atic electricity Do not use in special environments touch a nearby metal body to discharge static electricity from yourself before Do not use in places with high oil use touching the Wi Fi Adaptor including machine oil high steam levels or sulfuric gas this may lead to severe Static electricity from the human body may decrease in functionality and damage to damage the Wi Fi Adaptor unit parts Do not install the Wi Fi Adaptor in a place Turn off power supply of connected with high steam levels such as bathrooms equipment when performing construction or JU h Avoid places where water is splashed ibi or where condensation forms on walls Failure to turn off the power supply to Installing in such places can cause electric the connected equipment may lead to shock or breakdown malfunction or breakdown of the Wi Fi Adapt ted I t Do not install the Wi Fi Adaptor in places x c c with direct sunlight or where the ambient Dismantling the indoor unit temperature is 40 or more or is O C Please refer to the indoor units service or less Direct sunlight and high or low manual for detailed instructions for temperature environments may cause the accessing the control adaptor connector Wi Fi Adaptor to deform or breakdown CN105 on the indoor unit control PCB Please ensure that the access point The end user should read and accept the supports both WPS connection and the terms and conditions of the Wi Fi service WPA2 AES encryption
8. is installation manual The unit should be mounted in a location that can support its weight If the unit is installed in a location that cannot support its weight the Wi Fi Adaptor could fall and cause damage Connect and fasten the electric wires securely so external force on the wires will not apply on the terminals Improper connection and mounting may result in breakdown heat generation smoke generation or fire Mitsubishi Electric components or other designated components must be used for installation electric shock or damage water leaks Electrical work must be performed by a licensed professional using the instructions detailed in the installation manual Inadequate circuit capacity or improper installation may result in electric shock or fire This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliances This device complies with all Australia and New Zealand requirements for EMC and electrical safety Do not connect the Wi Fi Adaptor to earth inside the heat pump Caution Improper handling may have consequences including injury or damage to house To prevent damage from st
9. n state ce Adaptor unit Optional screw Optional screw Optional Fastener for with connecting for mounting for mounting mounting cord bundling the cable 5 core 85x16 4x16 clamp wires LED pattern ON O OFF Flashing escription LED1 LED2 LED3 Power is ON or software downloaded 0 5 sec interval 0 5 sec interval 0 5 sec interval WPS activated PBC 0 5 ser interval WPS activated PIN E wes9o O O WPS failed CV sec once every 5 sec Server and access point communication connected and heat pump communication failed 0 5 sec interval Server and access point communication connected and heat pump communication connected once every 5 sec once every 5 sec Server and access point communication connected and heat pump communication starting up once every 5 sec Server communication failed and heat pump communication connected 9 9 0 5 sec interval once every 5 sec Server communication or access point communication failed and heat pump communication starting up 0 5 sec interval Server communication or access point communication failed and heat pump communication failed 0 5 sec interval Access point communication failed and heat pump communication connected Access point communication failed and heat pump communication starting up 9 once every 5 sec gt Troubleshooting If at any stage you see the
10. p to 10 minutes MITSUBISHI A ELECTRIC II LED 2 orange lights up at any stage there may be a problem Check the troubleshooting section on page 11 MITSUBISHI A ELECTRIC When LED 1 remains solid for 5 seconds the adaptor is connecting to your router MITSUBISHI 5 ELECTRIC When LED 1 and LED 3 flash alternately the unit is successfully connected to the internet You can now download the Mitsubishi Control App and control your heat pump via Wi Fi You can restart the connection process at anytime by starting again from Step 1 Safety Instructions Read all safety instructions before using the Wi Fi Adaptor This installation manual contains important safety information Be sure to comply with the instructions After installing the Wi Fi Adaptor provide this installation manual to the user Instruct users to store it with their heat pump instruction manual in a safe location NWarning Improper handling may have serious consequences including serious injury or death e Installation of the adaptor must be carried Improper components may result in fire out by an authorised installer only Improper installation may result in fire electric shock or damage water leaks Consult the dealer from whom you purchased the unit ora professional installer The adaptor should be securely installed in accordance with th
Download Pdf Manuals
Related Search