BRADYMARKER XC Plus Printer
Contents
1. KEY TABS SL GSMA SLOTS valgera I gang POY Ha sHLTITAIL _ CORPECTISS LIS ate SSS ABEL WETESIAL sath OPES NG Page 19 lt a BRADY D Stuck label removal continued If a label becomes stuck inside the printer and can not be seen from outside the printer it 1s probably stuck to the rubber feed roller 1 To remove the label first remove the bottom rear cover the marker roll and roll holders See Figure 1 pg 1 and Figure 7 this page 2 Remove the material chute assembly by gently pressing the locking tabs away from the material chute assembly then lift the material chute assembly out of the printer case 3 The rubber feed roller is now visible Remove the label and clean any adhesive residue off the roller using isopropyl alcohol 4 Replace the material chute assembly It is important that the two sets of key tabs are properly inserted into the key slots One set of key tabs and slots is not visible To engage the key tabs push paper chute assembly down while pulling it toward the back of the printer You should feel the key tabs snap into place 5 Be sure that the material guide is properly positioned between the alignment slots then push the material chute assembly down so that the alignment tabs push through the alignment slots 6 Work the material chute assembly under one of the locking tabs Then insert a screwdriver or other pointed instrument through the material path opening Push t2. Serial Recall Arrows Insert Delete Menu Print Reprint Feed You can press this key any time It will direct you to the appropriate section of the user manual for further information Clears all characters from the Legend Entry Screen This works in conjunction with the LIST selection in the MENU It will store the current legend into the list that you are creating This key can act like a carriage return to add another line to the legend It also acts to select options from any part of the menu when it is highlighted This key will move from a submenu to the menu screen or from the menu screen to the Legend Entry Screen It will also terminate the printing of markers Press this key to define an individual character to be serialized Allows sequential viewing of legends in a created list Moves the cursor in the direction of the arrow This toggles the text to type over a character or insert a character If the cursor is flashing it will type over the character If it isn t it will insert a character Erases the character currently at the cursor Moves from the legend entry screen to the main menu Hold this key down to display your current main menu settings Prints the legend currently displayed or to begin printing markers from a legend list Duplicates he last marker printed Advances the marker roll to the next marker Use this to initially load the markers Page 6 lt a BRADY Paper shoot
3. Page 12 lt a BRADY Tutorial Before using charge the internal battery pack by plugging it into the AC adapter charger and allowing it to charge for 16 hours or more Install the ribbon onto the ribbon spool shaft with the spool drive pins pointing down Push the ribbon detector lever away from the spoon shaft press down on the ribbon spool until it clicks into place then release the ribbon detecting lever Repeat the process for the other side Tighten the ribbon by turning the right spool in a clockwise direction Move the material guide on the paper shoot to the appropriate size for the material selected Insert the material into the shoot Turn the unit on and press Feed This will advance the material into the printer Press the MENU key and Press S for Size Enter the size code of the material being used This should be on the inside of the material core and on the outside of the material box Press Enter Next select the label format Wiremarker Component Strip Press Enter Enter acknowledges acceptance of the selection Next go through the Menu and select the Type size Quantity Cycle and Justification needed for your application Remember to press Enter to accept each entry Enter the legend to be printed Press the Print key If you are in Multiple mode it will prompt you as to the quantity of each marker to print To serialize enter your legend and place the cursor under the character to be serialized Press
4. amp material guide assembly This is a three piece mechanical assembly through which the material labels pass before being printed This section can be taken apart for easy removal of labels that may have gotten stuck in the unit Optic eye The optic eye is the material sensing device on the BMXC s It senses the cut out on the material to align the marker for proper print positioning Ribbon The BMXC uses the R2200 ribbon The BMXC PS uses the R5200 ribbon Battery pack The battery pack must be charged for 16 hours with the AC adapter charger prior to usage for optimal performance To ensure proper charging the barrel plug must be fully inserted inside the power jack Only the molded housing should be visible The battery pack will last through 2 3 years of chargings A fully charged unit should last through a few days of continual usage Any nicad battery should be run until the battery low warning is displayed before recharging Page 7 lt a BRADY BMXC marker size codes Characters per line Marker Label Size Normal Size Small Size Large Size Width inches Page 8 BRADYMARKER PS printer A General unit description The Bradymarker PS printer is a Bradymarker XC Plus printer which has been modified to allow it to print PermaSleeve wire marking sleeves in addition to all other Bradymarker consumables This section will address changes and additions found in the PS model Differences between the two vers
5. TEM AJBB SN UIC BI133G Y GUIDE FOURS Before lubricating any location make sure that it is wiped clean of any dirt and old lubricant Always apply a minimum amount of lubricant a Apply a good quality grade of 40 lubricating oil to all oil points every six months b Apply a good quality 1 grease to all grease points every 12 months Note The shaft that the print head travels across must be lubricated with 1 grease Lubricating with oil will damage this shaft Page 17 lt a BRADY B Battery pack replacement Battery pack life will depend upon usage and operating conditions When recharging the battery pack always recharge at least 16 hours to restore full power to the pack This will result in longer battery pack life If you find that your battery pack is no longer holding a sufficient charge you should replace it with a new battery pack assembly part 29415 To replace the battery pack assembly follow these instructions 1 Remove the bottom rear cover and the bottom front cover 2 Slide the battery pack power jack from the slot in the edge of the printer body 3 Disconnect the battery pack connector from the printed circuit board Carefully slide the connector through the opening at the center of the printer 4 Remove the screw holding the battery pack assembly clamp to the bottom rear cover Note the proper position of the battery pack wire leads 5 Clamp the new battery pack assembly to t
6. c sensor Check the optic scanner to be sure it is in it s housing properly Labels are not advancing The material roll holding brackets are too tight against the roll Adjust them gently The paper shoot may not be installed correctly Remove it and reinstall it Check that there is no label stuck in the material path The rollers may have debris on them Clean with isopropyl alcohol If the customer gets the unit back and it is in a setup mode this may happen if they cleared the RAM or if a new chip was installed at the factory have them follow the prompted messages and answer them accordingly When they get to the motor speed press the E key eye and Enter so that the Optic Eye can scan Continue answering the prompted messages How long will the ribbon last At normal usage and operation the ribbon should last 3 to 6 months How long is the warranty 1 year Page 22 lt a BRADY Optional exercise Select a WML 202 292 4S label Set the BMXC to run 10 labels in serialization mode e Install a different material Create a List and enter 5 legends Then print this List using the List Print mode e Remove the paper shoot and clean the unit Remember to clean the Ribbon Guides and the platen Reinstall the paper shoot and use the cleaning kit to clean the print head Page 23
7. e printer Page 11 lt a BRADY BRADYMARKER PS printer continued E Printing other markers To print Bradymaker labels other than PermaSleeve marker 1 Replace the unwind assembly with the roll holder brackets See Fig 1 pg 1 2 Replace the printer cover with the standard Plus cover with tear bar Store the unused items in the Bradymarker carrying case for future use Set the print gap to its smallest setting as described in Section B pg 7 Then follow the instructions in the tutorial section F Maintenance amp Troubleshooting In general follow the instructions in the cleaning amp maintenance and troubleshooting sections Pay particular attention to the following items 1 The drive roller and nip roller o ring need to be cleaned occasionally to ensure proper feeding through the printer Refer to A stuck label removal for instructions on removing and installing the material chute assembly Clean both the drive roller and nip roller o rings with isopropyl alcohol 2 The position of the optic scanner within the print head gap adjuster mechanism is critical If bumped the scanner may move inside its holder resulting in one of the following error messages The front end of the metal optic scanner should be aligned with the bottom front edge of the plastic holding clip Gently slide the scanner inside the holding clip to re align if necessary Please verify size Scanning error Out of markers
8. ea BRADY BRADYMARKER XC Plus Printer Introduction Features and capabilities PermaSleeve adaptation Basic Operations Setup menu keyboard memory Tutorial Installation of labels and ribbons working with the menu printing and serializing labels Cleaning and maintenance Basic cleaning instructions removal and reinstallation of paper shoot Troubleshooting Most commonly asked questions Operational exercise Page 1 a BRADY ROLL OF MARKERS CASE NOTCHES FOR COVER LOCKS __ y PRINTER T COVER EAR BAR RIBBON SPOOLS ROLL HOLDER BRACKETS LIQUID CRYSTAL DISPLAY USER SCREEN KEYBOARD SP SICA KEYBOARO CURSOR amp EDITING KEYS POWER JACK KEYBOARD LETTER NUMBER amp SYMBOL KEYS FIGURE 1 Page 2 lt a BRADY Introduction to BMXC e The BMXC is a nine pin dot matrix portable printer capable of printing wire markers electronic component labels and general identification labels e Label registration is accomplished by optically sensing labels insuring proper label alignment e It is capable of printing eight lines per inch and 23 characters per line There are three text sizes and three formats available Full justification is another feature on the BMXC e The display is a two line 24 character liquid crystal display e Standard memory is 8K and can be expanded to 32K e Files can be created and stored in the BMXC for later usage e Print functions include mu
9. he bottom rear cover making sure that the wire leads are in the correct position 6 Push the battery pack connector through the opening at the center of the printer body Make sure that the terminals are located on the correct side to provide clearance from the printer case 7 Slide the battery pack power jack into the slot in the edge of the printer body Make sure that the terminals are located on the correct side to provide clearance from the printer case 8 Replace the bottom rear cover and bottom front cover C Lithium battery replacement The printed circuit board has a lithium backup battery This battery prevents the loss of stored legend lists in cases where the battery pack has been completely drained and the printer is not connected to a 120V power source Clean the unit OFTEN Even if not in use the environment will leave dust in the unit which may obstruct the optic sensor Included in the cleaning should be the white ribbon rewind tape on the right and left side of the platen remove the ribbon to see this tape The black platen tape cannot be replaced with electrical tape The reflective qualities of this tape is different than factory tape The optic sensor should be flush with the front most part of the housing A silver section will protrude from the back of the housing The optic sensor is factory set and does not need adjustment Page 18 es BRADY D Stuck label removal M amp TERIGLCHUTE i ASSEMEIT DE
10. he other locking tab while pushing down on the material chute assembly The material chute assembly will snap into place under the locking tab 7 Test the position of the material chute assembly by turning the idler roller You should feel some resistance If not the hidden set of key tabs are probably not installed properly Re install the material chute assembly and again turn the idler roller 8 Replace the bottom cover Page 20 lt a BRADY Additional tips continued If the unit must come in for repair 1 An RMA must be obtained from Brady s Tech Support Center at 800 643 8766 2 When ready to ship the unit in write up a short note stating the symptoms and enclose any samples that show the problem 3 Send the unit in it s protective case if available or wrap the unit in 2 3 of plastic bubble wrap Secure the bubble wrap around the unit This will protect it from damage in shipment DO NOT use styrofoam or biodegradable peanuts They break down during shipment and get into the unit causing extensive cleaning and possible damage 4 Write the RMA number on the outside of the box Page 21 lt a BRADY Troubleshooting amp most commonly asked questions Error Messages Please Verify Size Incorrect material size code entered Improper Format selected strip mode may be selected Check the optic scanner to be sure it is clean and in it s housing properly Scanning Error Clean the opti
11. ions of printer include the following refer to Fig 1 pg 1 1 The print head features a gap adjuster mechanism on the PS version see Section B 2 A print cover with no tear bar is needed when using PSBX sleeves two different covers are included with a PS unit 3 The roll holder brackets are replaced with a roll unwind assembly for PSBX sleeves When PermaSleeve markers are to be printed with the unit make sure the roll unwind assembly and PS printer cover no tear bar are installed on the unit Set the print head gap as in Section B Store the roll holder brackets and Plus printer cover with tear bar in the Bradymarker carrying case for future use see Section E pg 8 B Setting the print head gap The Bradymarker PS printer features a print head gap adjuster mechanism which allows it to compensate for material thickness The gap is adjusted as follows refer to Fig A na NG wa N f S Ap x wie anus uc al We SCREW ANG SCRIVI FIGUAT A 1 Remove the print cover 2 Using a slotted screwdriver loosen the adjuster lock screw by turning it one revolution counter clockwise Page 9 lt a BRADY BRADYMARKER PS printer 3 With screwdriver turn the plastic gap adjustment screw turn clockwise only To the desired setting The smallest gap locator dots at 12 o clock is used for all non PermaSleeve consumables The next smallest gap 4 o cl
12. le time It will automatically center your text vertically Strip wiremarker mode is identical to the wiremarker format except that it allows you to print duplicate markers on a multiple across label a butt cut label This format will always print the same text in each strip of label It is considered a single label for printing and serialization This mode will print either in the Single Marker mode and print one marker for each print command or print in the Multiple Marker mode and print more than one marker from the print mode You will be prompted for the number of markers to print This will allow center left or right justification on your marker All text must be printed using the same justification This setting is NOT held in memory with your legend list Normal 12 cpi Small 16 cpi Large 8 cpi and half height 16 cpi A single size text is selected and will remain until a new type size is selected Changing the type size will erase any test on the legend screen This is the area in which files are stored in memory The BMXC can store up to 26 unique legend lists It can store up to 6500 characters of legend information in its standard 8k memory The memory can be expanded to 32k The LIST part of the MENU has a submenu which includes Create Print View Edit Add to and Erase Each of the selections deal with the List saved files Page 5 lt a BRADY Keyboard Help Clear Display Save Enter Exit Stop
13. ltiple copies and automatic numeric or alphabetic serialization The BMXC can be run on battery or AC power The battery charger is a UL listed 120V 60Hz input 12VAC 2A output adapter It will print 500 labels before recharging e PermaSleeve printing is available on the BMXC PS The BMXC can be adapted to handle this type of printing Page 3 es BRADY Legend entry screen Legend Entry Screen Press MENU key MAIN MENU List Size Format Oty Cycle Type Justify Press L Press Press F Press Q Press T Press J SUB MENU Create Print View Edit Addto Erase Press Press P Press V Press A Press E OPTIONS Create Print View Edit Addto Erase Enter Wire Com Strip Single Multiple Small Normal Large Left Center Right List List List List List Brady marker ponent ee es e Size Press Press Press Press Press Press W Press C PressS Press Press M Press S Press N PressL PressL Press C Press R List List List List List Name Name Name Name Name FIGURE 3 Page 4 BRADY Basic Operations Menu Size Format Quantity Justify List This is the material size code It can be obtained from the box or from the inner core of the label The parameters for the legend is determined by this size code There are three formats on the BMXC wiremarker component and strip Wiremarker mode automatically repeats the line of text in the legend down the length of the marker Component mode will print all of your legend a sing
14. ock is the standard setting for PermaSleeve markers The final position 7 o clock should only be used if the printer smears with the 4 o clock setting 4 With screwdriver re tighten adjuster lock screw Be careful not to over tighten screw 5 Replace printer cover When adjusting the print head gap be careful not to move the optic scanner within its plastic holder The scanner position is critical to proper machine operation If scanner is accidentally moved refer to Section F pg 10 for instructions on resetting the scanner gap C Setting the unit for sleeve size Follow the instructions on page 11 in the tutorial section Press the MENU key Like other Bradymarker labels PermaSleeve markers have the marker size code shown on the package and on the inside of the roll core After entering the marker size code and the appropriate format option you will be asked the question Printing PSBX sleeves Press Y or N Select Y in using PermaSleeve markers select N in all other cases This will set the proper margin for the printer This is necessary due to PermaSleeve markers different location left to right on its carrier than other Bradymarker labels D Loading PermaSleeve wire marker sleeves Before attempting to load PermaSleeve markers make sure that unwind assembly and proper printer cover are in place material guide is set to widest position and correct marker size information had been entered Load PermaSlee
15. printed Page 13 lt a BRADY Tutorial continued IMPORTANT Be sure to choose the label size font size and justification before going into the List feature These settings will be saved with the file saved To Erase a List from memory select Menu List the name of the file and press Erase You will be prompted Erase List X press Y or N Page 14 es BRADY Ribbon Installation AIDAON RIBBON SPOOL DETECTORS HIBRUN RIBBON wits RIBBON OPTIC GUIDE FRINT REGISTRATION HEAD SCANNER j RIBBON INSTALLATION SPOOL DRIVE PINS Page 15 lt a BRADY Cleaning and maintenance A Cleaning and lubrication The printer is a rugged mechanism It should be cleaned and lubricated as indicated below to keep it in top operating condition 1 a b c Cleaning Several areas need occasional cleaning See Figure 5 on the next page First is the platen White paper lint collects on the black tape attached to the platen causing the optic registration system to misread the notch on the label liner Clean this at least once every month using alcohol on a cotton swab Second is the ink ribbon guide path The ink has a tendency to build a thick paste like material on the two outside ribbon guides This increases the driving friction of the ink ribbon which causes the drive pins on the ink ribbon spool to fail Clean these ribbon guides with a small amount of alcohol on a cotton swab each time you ins
16. tall a new ribbon Third is the print head Poor print quality or missing print dots may be an indication that your print head requires cleaning A Brady printer cleaning kit is available from your W H Brady Co Distributor catalog PCK 1 Use the cleaning kit and follow the instructions below 1 While holding down the H key turn the printer on Follow the instructions as displayed on the user screen IMPORTANT Be sure to remove the ribbon before you try to clean the print head The print head should be cleaned using a strip of print element cleaning material that is 1 3 4 wide by approximately 6 long Saturate the first 4 of the strip with cleaning solution before feeding into the printer Feed the strip so that the wet side is facing the print head Loose cleaning material can severely damage the printer If you tear material along perforations be sure to trim all the edges of the cleaning strip Be sure to thoroughly clean the print head You may need to run more than one cleaning material strip through the printer to completely clean the print head If your printing quality does not improve you may have a worn ribbon Replacement ribbons catalog R2100 are available from your W H Brady Co Distributor Page 16 lt a BRADY 2 Lubrication Figure 5 also indicates those points on the printer mechanism that require periodic lubrication Oil points are noted by an O grease points by a G G 6 PLS
17. the Serial key The character block will be blinking If more than one number will be incremented each character must be serialized blinking Example the starting number is 1234 and the final number is 1250 the last two characters must be selected and serialized by pressing the Serial key for them to increment Serialized characters are always incremented by one number or one letter Press Print and enter the number of each identical labels to be printed this is usually 1 press Enter You will be prompted for the Number of Times to Increment a Serial Enter the total number to incremented labels you want not the number you want the unit to increment to The BMXC will increment the character furthest to the right first When it reaches 0 or Z the next character will start incrementing To save a legend in memory first select Menu and press L for List select Create press Enter and select any of the lower case letters Type in your legend and press Save This will add the legend to the memory The LCD will display the Legend will be added to List X message Press Clear Display and type in the next legend to be saved Press Save It is possible to add to this List at a later date by selecting the Add To feature in the Menu and enter legends as before A List can be edited by using the View Edit command If you know the letter of the List you want to print you can select Print from the List Menu and enter the number of each label to be
18. ve markers as follows refer to Fig B 1 Make sure power in ON 2 With the leading end approximately on top of the roll set the roll of sleeves into the unwind assembly so that they will unwind in the direction shown in Fig B on the next page 3 Turn the roll backwards opposite the arrow in Fig B until the leading edge pops under the front roller in the unwind assembly Page 10 lt a BRADY BRADYMARKER PS printer continued 4 Reverse direction and turn the roll forward Feed material into printer until it stops The leading edge will now be positioned against the drive roller 5 While continuing to hold the roll so that the leading edge is pushed tightly against the drive roll press and hold the FEED key The drive roller will begin to pull markers into the printer Continue to hold the FEED key until the leading edge of the roll becomes visible through the slot in the top of the printer cover FIGURE B 6 Release the FEED key The printer should advance to the top of the first available PermaSleeve marker You are now ready to enter legends and print sleeves WARNING NEVER try to remove any Bradymarker label or sleeve by pulling them out of the rear of the printer The printer drive is one way only To remove markers insert a scissors in the slot for scissors in the unwind assembly see Fig B cut through the carrier between sleeves and pull the sleeve out though the top of th
Download Pdf Manuals
Related Search