ptx Radio IC 16
Contents
1. of the box Astepper function with 16 different intervals can be programmed ptx Radio IC 16 is equipped with a separate battery pack equipped with a powerful Li lon battery By using ptx Radio IC 16 with the associated battery pack it is not allowed to connect other additional power supply units like ptx MFB ptx RM on plug DATA OUT ptx Radio IC 16 can be used as well as a radio or cable device ptx system is a bidirectional system with a ptx Controller all outputs can be programmed tested and ignited s manual of ptx Controller 3 Handling On top of the box there are the 16 output terminals and I antenna socket in front the 3 turn switches to set the address 1 turn switch to set the freguency and two plugs DATA IN and DATA OUT to connect the box with other ptx devices With full charged battery it is possible to connect 3 more pix IC 16 or 1 more pix IC 48 Data OUT One red LED shows the status ARMED By using ptx Radio IC 16 with the associated battery pack it is not allowed to connect other additional power supply units like ptx MFB ptx RM on plug DATA OUT The seperate battery pack is egipped with a display to control the battery capacity and a plug to connect with the ptx Radio IC 16 ptx Radio IC 16 4 Battery ptx Radio IC is equipped with a separate battery case Set the battery to the left side of the ptx Radio IC and save the case with a carabiner Connect the plug of the battery with ptx Radio I2. C The LED at the battery case is an indicator of battery capacity press the switch on top of the battery case the led shows the battery capacity LED green flashing battery max LED green 100 LED orange 70 LED red 40 LED red flashing 10 Charging the battery is possible with the associated ptx charger 5 Addressing Setting the address is possible by 3 turn switches Up to 200 different addresses are avallable 223 La E a LT Fi a oa o o mn o F L U a o 5 Bi L Additional to the address the function of the box can set with the left turn switch 2 different features are availble Ignition box every single output can be programmed adjustment IC met tto nt un ESA Co Stepper started by one impulse and running in a definite interval adjustment STEP ptx Radio IC 16 3 5 k E On soe ia oa SA un F T a o 2 Bt BL 6 Addressing ptx Radio IC 16 in operation mode IC ignition box With the turn switches the address will be set left turn switch is in zone IC switch setting IC 001 ptx Radio 16 address Nr 1 23 Li switch setting IC 011 ptx Radio IC 16 address Nr 11 3 E ont 23 oa o uno g i F L U Eh o switch setting IC 111 ptx Radio IC 16 address Nr 111 bak ou t r 23 left to the right Up to 200 different addresses are selectable Programming of every single output is possible with any ptx Controller description will be find
3. e the safety instructions in this manual Observe the safety instructions of the fireworks pyrotechnic effects and respect the recommend safety distances The operating technician must have an unrestricted view to the firing position as well as to the whole fireworks pyrotechnic area Never put your face or other parts of your body over fireworks pyrotechnic effects with armed ignition hoxes Maintain the appropriate distance of separation for the effect or firework being used when ptx Ignition System gets powered The specific procedures pertaining to the use and operation of the ptx Ignition System are outlined in the user manual Deviation from any of the procedures outlined in this manual are specifically forbidden and not recommended by Pyrotronix GmbH Any deviations to the procedures as outlined in the user manual may result in property damage or personal injury Any deviations to the procedures as outlined in the user manual is considered a misuse of the system and done so at your own risk PYROTRONIX Show Control Systems GmbH Germany cannot be held responsible for any harm caused by the misuse improper electrical connection failure to properly maintain improper handling of pyrotechnics and fireworks or deviation from the procedures outlined in ptx system user manual ptx Radio IC 16 2 Description ptx Radio IC 16 is a radio ignition box with 16 outputs Setting the address and the frequency Is possible with 3 turn switches at the front
4. hannel Connected ptx boxes Data Out Stand by time Dimension L x H x B Weight Battery Battery Charge time Dimension L x H x B Weight ptx Radio IC 16 16 33V 40 igniter per output 300 integrated 16 1000m 0 E 869MHz F 915MHz 16 max 3 pix IC 16 or 1 pix IC 48 10h 280 x 140 x 80mm 1 06kg Li lon Ah 280 x 55 x 25mm 0 65kg From August 1 2011 we offer a new frequency for some countries outside of Europe New frequency is 915MHz setting is with frequency switch position F From this day all ptx radio devices will be delivered with this setting
5. into the respective manuals 7 Addressing ptx Radio IC 16 in operation mode Stepper With the turn switches the address will be set left turn switch is in zone STEP switch setting STEP 001 ptx Stepper address Nr 1 switch setting 011 ptx Stepper address Nr 11 2 22 L L Om e 7 E oa de m g F LD E a o B L BI switch setting 111 ptx Stepper address Nr 111 2 22 L Om y r oa do uno o ini F ne oy r Eh B L E L left to the right ptx Radio IC 16 Up to 200 different Stepper addresses are selectable 16 different intervals can be programmed Duration of the interval depends on the positioning of the cue No start time Adjustable intervals 15 900ms 600ms 700ms G ms 500ms 400ms 300ms Different intervals are settable by positioning of the programmed cue No ls 900ms 800ms 700ms 600ms 500ms 400ms 300ms 9 Ausgang 10 Ausgang 11 n ng 12 Ausgang 13 Ausga nz 14 Ausgang 15 Ausgang 16 B ms 60ms 40ms 20ms Ignition starts always from output 1 and is running to output 16 The picture below shows a ptx IC 16 every interval is assigned to an output Cue No 1 dedicated to output 5 means Stepper starts at cue No 1 the interval between the single outputs is 600ms 0 65 sa EEE ea erte 5 w wlsoeoisn Diz els w e 8 38 2828 28 28 28 ami SE 78 23 m Next example Cue No 1 dedicated to
6. output 11 means Stepper starts at cue No 1 the interval between the single outputs is 80ms 0 08s ptx Radio IC 16 THAE Cue No 5 dedicated to output 5 means Stepper starts at cue No 5 the interval between the single outputs is 20ms 0 02s 38 38 3832 38 3 3 ler da Ija eon 38 23 23 28 28 28 28 Cue No 24 dedicated to output 16 means Stepper starts at cue No 24 the interval between the single outputs is Oms 0 00s all 16 outputs ignite at the same time 24 sjef AEE 338 33lis ze zslislze z el n mens Are there several cues dedicated to one stepper the first programming cue output 1 16 is valid Allocating safety zones to a stepper is possible s manual ptx Controller Activated safety zones prevent the start time of the stepper The ignition can t stop by activating the safety zone if the stepper is already started At this moment a break off is only possible by a ptx Controller s Manual ptx Controller ptx Radio IC 16 8 Frequency setting With the turn switch on front of the box it is possible to set the frequency There are 16 different possibilities 0 F 9 Ignition Is the ptx IC 16 ready for ignition controlled by any ptx Controller the red LED at the right side of the case will light on 10 Technical Data Qutputs Qutgoing channel Ignition power Ignition capacity Stepper function Interval Range Frequency Radio c
7. ptx Radio IC 16 Manual ptx Radio IC 16 Dear client Thank you very much for buying the German engineered ptx system We are very pleased you made the decision to use our products Pyrotronix Show Control Systems assures you state of the art equipment with components designed for reliable performance indoor and outdoor The rugged components of the ptx system offers the firework designer enormous set up possibilities as well as an easy and simple work flow from the show script till the set up Please note that all manual as well as all screen displays keyboard layouts hardware descriptions or software are subjects to copyrights and other intellectual property rights of PYROTRONIX Show Control Systems GmbH Germany O August 2012 PYROTRONIX Show Control Systems GmbH Germany all rights reserved ptx Radio IC 16 Content 1 General Safety Instructions sooeronrersrenrrenrersrereresrersrenerenerssensrensersrenserssenssenserssenssensen 4 2 Description RS 5 GR EEE 9 o In 6 O AES ae 6 6 Addressing ptx Radio IC 16 in operation mode IC ignition box G 7 7 Addressing ptx Radio IC 16 in operation mode SC g 7 8 Frequency setting PS 10 Zo OOO P Pp 10 10 Technical Dala coronas adan i i i i i i i 11 ptx Radio IC 16 1 General Safety Instructions The correct order of setting up and connecting ptx system is mandatory for every user in order to achieve the highest degree of safety At the beginning of the setting up p
8. rocess please ensure that the control panel key is with the responsible person ptx system must only be operated with original equipment and accessories manufactured by Pyrotronix Show Control Systems Germany The use of non original equipment may result in the malfunction of the ptx system Misuse of the ptx system may lead to property damage or personal injury The ptx system Is designed for professional use only Professional fireworks pyrotechnic operators shall only use the system in a controlled professional environment permitted by the authority having jurisdiction ptx system shall only be used to ignite pyrotechnics and fireworks Connecting components or effects to the system is only allowed when no power source Is connected to the system whenever you are setting up connecting or adding components or effects This also applies to every kind of work with fireworks pyrotechnic devices Before using ptx system and effects in public places the necessary notifications permissions must be obtained from the responsible authorities When working in close proximity to people staging scenery or similar things it Is very important that safety standards be closely followed Familiarity with staging scenery or similar things Is necessary to maintain appropriate safety standards Smoking and open flames or lights shall be banned in the pyrotechnic fireworks area You shall be familiar with the fire alarm detection and suppression systems Observ
Download Pdf Manuals
Related Search