Home
MSP430-JTAG-ISO-MK2 USER`S MANUAL
Contents
1. MSP430 JTAG ISO MK2 rofessional MSP430 programmer debugger USER S MANUAL Preliminary August 2012 Designed by OLIMEX Ltd 2012 lead free All boards produced by Olimex LTD are ROHS compliant OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual DISCLAIMER 2012 Olimex Ltd Olimex logo and combinations thereof are registered trademarks of Olimex Ltd Other product names may be trademarks of others and the rights belong to their respective owners The information in this document is provided in connection with Olimex products No license express or implied or otherwise to any intellectual property right is granted by this document or in connection with the sale of Olimex products It is possible that the pictures in this manual differ from the latest revision of the board The software provided and the hardware design of MSP430 JTAG ISO MKQ2 are closed source and belong to OLIMEX LTD The product described in this document is subject to continuous development and improvements All particulars of the product and its use contained in this document are given by OLIMEX in good faith However all warranties implied or expressed including but not limited to implied warranties of merchantability or fitness for purpose are excluded This document is intended only to assist the reader in the use of the product OLIMEX Ltd shall not be liable for any loss or damage arising from the use of any information in this document or any error o
2. caused due to our fault and we will repair replace the faulty hardware free of charge otherwise we can quote price of the repair Note that all shippings back and forth have to be covered by the customer Before you ship anything back you need to ask for RMA When you ship back please attach to it your shipping address phone e mail RMA and brief description of the problem All boards should be sent back in antistatic package and well packed to prevent damages during the transport Page 23 of 23
3. s Manual CHAPTER 3 MSP430 JTAG ISO MK2 BOARD DESCRIPTION 3 Introduction to the chapter Here you get acquainted with the main parts of the board and their location on the case Some of the elements are named near their position on the case of MSP430 JTAG ISO MK2 3 1 Basic device description In the table below are show the main parts of the board and their positioning on the case MSP430 JTAG ISO MK2 description Display Power LED Status LED Communication LED Up Increment button Select button 7 Down Decrement button Mode Back button USB connector JTAG SBW connector External power connector The functions supported are further explained in the next chapters of this document Page 9 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual The LEDs functions are detailed in the table below GREEN jw INDICATES THE DEVICE IS PROPERLY WORKING BLINKING ERROR or UNDEFINED PROGRAMMER DEBUGGER STATE YELLOW BLINKING USB OR JTAG SBW COMMUNICATION It is not recommended to power down the board when the YELLOW LED is blinking Page 10 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual CHAPTER 4 MODES OF OPERATION 4 Introduction ot the chapter In this chapter we will explain the mode options of MSP430 JTAG ISO MK2 Furthermore a step by step guide to each option will be provided Each option will be explained MSP430 JTAG ISO MK2 has three modes of operation Upon powering the device from external sou
4. 3 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual NOTE THIS IS A PRELIMINARY MANUAL VERSION IT IS NOT COMPLETE THE FIRMWARE OF THE PROGRAMMER IS UNDER REVISION Page 4 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual CHAPTER 1 OVERVIEW 1 Introduction to the chapter Thank you for choosing the MSP430 JTAG ISO MK2 debugger programmer This document provides a user s guide for the Olimex MSP430 JTAG ISO MK2 As an overview this chapter gives the scope of this document and lists the board s features The document s organization is then detailed The MSP430 JTAG ISO MK2 programmer debugger development board enables code uploading of applications running on MSP430 microcontrollers manufactured by Texas Instruments The product is our most sophisticated MSP430 programmer debugger and has many improvements over the our previous MSP430 tools 1 1 Features Supports both JTAG and SWD interfaces LCD display for convenient navigation between different modes of operation 1 76 GB internal memory available for custom code Stand alone mode or mass storage 3 different modes of operation Debugger Mass storage Stand alone Can be powered either by external power or the USB interface Extended firmware features target voltage display target current consumption display Sleek and solid black case Sophisticated custom made front panel 14 pin JTAG ribbon cable included Dimensions 75mm x 111mm 2 95 x 4 37 1 2 Target ma
5. 3 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual 1 Mode of operation Stand alone mode 2 Open an existing previously saved project 3 Highlighted operation Up Increment button Down Decrement button 4 Create new project 5 Change mode Mode Back button 6 Select the highlighted operation Select button 4 4 1 Opening an existing project gt F11x1_P OPJ 3 FE427_N OPJ BACK SELECT 1 Sub menu OPEN 2 Available projects 3 Highlight Up Increment button Down Decrement button 4 Back to the upper menu Mode Back button 5 Select the highlighted project Select button Page 14 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual 4 4 2 Editing the open project 1 3 2 gt IF JTAG 4 Vt 3 3V Blow ON BACK 1 Sub menu EDIT 2 Highlighted operation Up Increment button Down Decrement button 3 Choosing the default programmer interface JTAG SBW AUTO automatically chooses JTAG or SBW interface is available 4 Shows the current voltage of the microcontroller 5 Blows the READ fuse of the target ON OFF 6 Back to the Open sub menu Mode Back button 7 Store the changes in the project Select button Page 15 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual 4 4 3 Writing in an existing project 1 WRITE MCU F11x1_P 2 IF AUTO 3 4 5 1 Sub menu WRITE 2 Microcontroller type 3 Interface used 4 READ protection fuse 5
6. Voltage of the microcontroller 6 Back to EDIT sub menu Mode Back button 7 Store Select button Page 16 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual 4 4 4 Reading from a microcontroller READ gt IF AUTO Vt 3 3 Upload BACK SELECT 1 Sub menu READ 2 Highlighted operation Up Increment button Down Decrement button 3 Programming interface 4 Voltage of the microcontroller 5 Reading the program from the microcontroller and creating a project file named the type of the microcontroller and consecutive number 6 Back to the main menu Mode Back button 7 Select the highlighted operation Select button Page 17 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual CHAPTER 5 OPJ FILE FORMAT opma Ha OPJ aiia lt xml version 1 0 encoding UTF 8 gt xml header lt ISO_V2 gt ISO V2 cexyna lt Device ID gt ID Ha koHrporrepa lt Device interface JTAG SWD AUTO gt THI Ha HHTepdelica lt Device voltage 1800 3600 mV gt 34XpaHBalljO HallpexKeHHe Ha KOHTpO Iepa Target Id 15 IF JTAG Vt 3000 gt orrepauua ON OFF lt Erase device 0 1 gt H3TpHBaHe lt Blank check device 0 1 gt Blank check lt Programming device 0 1 gt IIporpaMHpaHe lt Verify device 0 1 gt IIpoBepka lt Blow device 0 1 gt 3allJMTa OT UeTeHe lt File name gt uve Ha TXT um HEX daiiia c nporpavara 3a 3arc Progr
7. amming Erase 1 Blank 1 Write 1 Verify 1 Blow 0 File test txt gt lt Serializing enable 0 1 gt cepvamu3auua ON OFF lt Serial number format HEX BDC gt TAN Ha cepHiHHsi HOMep lt Serial number endian LE BE32 BE8 gt TAN IIpe ICTaBSHeTO Ha HOMepa lt Serial number size 1 4 bytes gt pa3Mep Ha CepHAHHs HOMep lt Serial number start address gt CTapTOB ayipec Ha cepH HHA HOMep lt Serial number gt TeKyIHH5I CepHeH HOMep lt Last serial number gt IIOC Ie IeH cepHeH HOMep SN Enable 1 Format HEX Endian LE Size 4 Addr 1024 Count 0x80000000 Last 0xFFFFFFFEF gt lt Sections preserve gt ONMCcaHHe Ha CeKHHHTe KOHTO He ce Mogjuuunapar Section lt Section start address gt CTapTOB ayIpec lt Section size gt pa3Mep Ha CeKIMATAa Entry Start 0x11111111 Size 0x21111111 gt Entry Start 0x31111111 Size 0x41111111 gt Entry Start 0x51111111 Size 0x61111111 gt Entry Start 0x71111111 Size 0x81111111 gt lt Entry Start 0x91111111 Size 0xA1111111 gt Entry Start 0xB1111111 Size 0xC1111111 gt Page 18 of 23 OLIMEXO 2012 lt Entry Start 0xD1111111 Size 0xE1111111 gt Entry Start 0xF1111111 Size OxFFFFFFFF gt lt Section gt ISO V2 Page 19 of 23 MSP430 JTAG ISO MK2 User s Manual OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual CHAPTER 6 DIMENSIONS 6 Introduct
8. dware information and error reports mail to support olimex com Note that we are primarily a hardware company and our software support is limited Please consider reading the paragraph below about the warranty of Olimex products Warranty and returns Our boards have lifetime warranty against manufacturing defects and components During development work it is not unlikely that you can burn your programmer or development board This is normal we also do development work and we have damaged A LOT of programmers and boards during our daily job so we know how it works If our board programmer has worked fine then stopped please check if you didn t apply over voltage by mistake or shorted something in your target board where the programmer was connected etc Sometimes boards might get damaged by ESD shock voltage or if you spill coffee on them during your work when they are powered Please note that warrany do not cover problems caused by unproper use shorts over voltages ESD shock etc If the board has warranty label it should be not broken Broken labels void the warranty same applies for boards modified by the customer for instance soldering additional components or removing components such boards will be not be a subject of our warranty If you are positive that the problem is due to manufacturing defect or component you can return the board back to us for inspection When we receive the board we will check and if the problem is
9. ion to the chapter In this chapter are located the schematics describing logically and physically MSP430 JTAG ISO MK2 Note that all dimensions are in mils TO BE ADDED LATER Page 20 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual CHAPTER 7 REVISION HISTORY WEB LINKS AND SUPPORT 7 Introduction to the chapter In this chapter you will find the current and the previous version of the document you are reading Also the web page for your device is listed Be sure to check it after a purchase for the latest available updates and examples 7 1 Document revision Changes Modified Pages at Preliminary revision 01 08 12 7 2 Device revision Notable Changes Initial release of the device Page 21 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual 7 3 Useful web links and purchase codes The web page you can visit for more info on your device is https www olimex com dev MSP430 JTAG ISO MK2 html ORDER CODES MSP430 JTAG ISO MK2 professional programmer featuring LCD SD card stand alone mode 12V target supply USB CABLE USB type A to USB type B cable The latest price list can be found at http olimex com dev pricelist html How to order You can order to us directly or by any of our distributors Check http www olimex com and http olimex com dev order html for more info Page 22 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual 7 4 Product support For product support har
10. ower up the board is given and a description of the default board behavior is detailed 2 1 Electrostatic warning MSP430 JTAG ISO MKQ is shipped in a protective anti static package The board must not be exposed to high electrostatic potentials A grounding strap or similar protective device should be worn when handling the board Avoid touching the component pins or any other metallic element 2 3 Hardware requirements The board can be powered either by the USB or by 12V external source If you use the USB note that the connector is type B to connect to a personal computer you will probably need USB A to USB B cable which is not included in the package You can purchase such a cable from us the code is USB CABLE USB standard type A to USB standard type B cable Powering the board from external source is very convenient for stand alone mode since you don t need to be connected to a personal computer once you have uploaded the needed files 2 4 Software requirements Page 7 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual 2 5 First time start up Setting up the MSP430 JTAG ISO MK2 for development purposes might vary between different users However at least a personal computer with a working USB port and a cable USB type A to USB type B are required Connect the device to the computer via the cable A new device should be recognized by your device manager Go Page 8 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User
11. r omission in such information or any incorrect use of the product This MSP430 JTAG ISO MK2 is intended for use for engineering development demonstration or evaluation purposes only and is not considered by OLIMEX to be a finished end product fit for general consumer use Persons handling the product must have electronics training and observe good engineering practice standards As such the goods being provided are not intended to be complete in terms of required design marketing and or manufacturing related protective considerations including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards Olimex currently deals with a variety of customers for products and therefore our arrangement with the user is not exclusive Olimex assumes no liability for applications assistance customer product design software performance or infringement of patents or services described herein THERE IS NO WARRANTY FOR THE DESIGN MATERIALS AND THE COMPONENTS USED TO CREATE MSP430 JTAG ISO MK2 THEY ARE CONSIDERED SUITABLE ONLY MSP430 JTAG ISO MK2 Page 2 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual Table of Contents CHAPTER 6 DIMENSIONS cas aoe oleate cus sua tta Ue Qu ae RR UM PS Gi pa a SUE Suo MEE 20 6 Introduction to the Chapte cccsccccccsssssssssssssssssssssssscnsssccsssssessssccssccscssecsssssssscsscecsoes 20 Page 3 of 2
12. rce of power 12V or via the USB 5V the screen should look like the image below Debugger Mass Storage Stand alone SELECT The three marked sections have different meaning 1 Mode select up arrow key increment button down arrow key decrement button mode select maker is used to navigate to desired new mode the available modes are Debugger Mass Storage Stand Alone 2 Current mode current mode highlights the mode lastly used 3 Confirm selection right arrow key select button confirms our selected by mode select choice Each of the modes selected are explained in the next sub chapters Page 11 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual 4 2 Debugger mode Debugger mode is used when you have connected Debugger MCU F11x1_P Power EXT 4 Vt 3 3 It 100uA MODE 1 Work mode 2 Microcontroller type 3 Source of power EXT shows the target is powered from external source different than MSP430 JTAG ISO MK2 INT means the target is powered by our debugger programmer ISO MK2 4 Shows microcontroller power 5 Shows current consumption only if powering the target from the MSP430 JTAG ISO MK2 6 Change the mode button Mode Back button Page 12 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual 4 3 Mass storage mode Mass storage 1 Mode of operation mass storage 2 Change mode Mode Back button 4 4 Stand alone mode 1 Stand alone Page 1
13. rket and purpose of the device MSP430 JTAG ISO MKQ is suitable for programming and debugging all Texas Instruments MSP430 microcontrollers which support JTAG or SBW Spy Bi Wire interfaces The device is recommended for all MSP430 fans It is especially convenient for mass production due to the ease of stand alone programming Page 5 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual 1 3 Organization of this document Each section in this document covers a separate topic organized as follow Chapter 1 is an overview of the board usage and features Chapter 2 lists the additional software and hardware means you might need for proper use of the device Chapter 3 contains detailed description of the board peripherals and the basic controls Chapter 4 describes the modes of operation the MSP430 JTAG ISO MK2 microcontroller Chapter 5 is an explanation of the file format used for stand alone programming Chapter 6 shows the dimensions of MSP430 JTAG ISO MK2 Chapter 7 contains the revision history the useful web links and support information Page 6 of 23 OLIMEXO 2012 MSP430 JTAG ISO MK2 User s Manual CHAPTER 2 REQUIREMENTS AND FIRST START UP 2 Introduction to the chapter This section helps you set up the MSP430 JTAG ISO MK2 development board for the first time Please consider first the electrostatic warning to avoid damaging the board then discover the hardware and software required to operate the board The procedure to p
Download Pdf Manuals
Related Search
Related Contents
EA993BB−15(油圧ジャッキ)取扱説明書 CheckExtractor™ - Greiner Bio GEDA Molly DELL UltraSharp U2713H Teka DB1 60 Hardware User Guide Procédure L3 Gebruiksaanwijzing PLENTY Vaporiateur mode d`emploi Copyright © All rights reserved.
Failed to retrieve file