SeaLand electronic toilet flush switch instructions-template
Contents
1. 4 2 Normal toilet operation ADD WATER TO TOILET BOWL and panel backlighting function Press Add Water switch until desired water level is achieved More water is usually A added only when flushing solids If switch is pressed too long water flow will shut off automatically to avoid overflow ADD BACKLIGHTING To turn switch backlighting effect off or on push Add Water WATER switch twice very quickly FLUSH TOILET Press Flush switch down for a moment then release it Flush only when the green CW OK to Flush light is on Toilet will not flush until the green OK to Flush light is on It takes about one minute for vacuum to recharge for the next flush FLUSH If the red Do Not Flush light is on the system is either recharging the vacuum or the holding tank is full Do not attempt to flush the toilet during these conditions ora clog may occur in the toilet system DO NOT FLUSH FOREIGN OBJECTS q CAUTION Flush only water bodily wastes and rapid dissolving tissue paper Do not AN 4 flush wet wipes sanitary napkins condoms diapers razor blades paper cups VA oT cotton swabs food hair or liquids such as oils or solvents Clogging or damage to the toilet system may occur Note i Make sure all guests understand toilet operation before use 4 3 Changing flush modes SeaLand VacuFlush all ceramic toilets offer two flush settings to help manage water consumption Normal flush Use2. complete press the Service buttom for three seconds to change back to normal toilet operation o ______ 5 Flush Switch p Wall Templates oO ut h Note See important information on back page before using 2 in either template ue 51 mm VFS and DES 2 in 51 mm clearance WALL BRACKET behind wall surface required 1 875 in 64 mm et 6 p VFP and DFP E ToO WALL BRACKET 2 25 in an 57 mm D 2 in 51 mm clearance behind wall surface required 2 5 in 64 mm ee es ae sees sees al 6 Cover Plate Connection Points A Dometic 3 Gewiss Chorus G Gewiss Playbus 2 Vimar Eikon 4 Vimar Idea Gray line indicates area to be removed for Eikon series cover plate Remove from both sides of bracket VFS and DFS WALL BRACKET VFP and DFP WALL BRACKET O Dometic DOMETIC CORPORATION Registered Trademark of Dometic Corporation sass P dse Dometic Corporation BIG PRAIRIE OHIO 44611 USA 600346829 02 1112 www dometic com
3. Seafand by Dometic GROUP Electronic flush switches installation and operation manual O Dometic O Dometic N oKTo ee Power FLUSH _ DO NOT gt TANK FLUSH LEVEL E gt SERVICE VFS VFP models for VacuFlush toilets DFS DFP models for other SeaLand toilets SeaLand Electronic Flush Switches INSTALLATION gt OPERATION VFS VFP flush switches for VacuFlush electric flush toilets DFS DFP flush switches for MasterFlush and RushFlush electric flush toilets CE approved 1 Installation 1 1 Internal function switches The SeaLand flush switch includes a set of internal function switches inside the back of the panel which allow it to operate with new and older SeaLand electric flush toilets The normal position of the panel s internal function switches for new toilets are ON CTS ON CTS 1 2 1 2 VFS and VFP panels DFS and DFP panels WHEN INSTALLING A SEALAND ELECTRONIC FLUSH SWITCH with OLDER VACUFLUSH OR MASTERFLUSH TOILET serial number on toilet ID label contains prefix 223 or lower 1 With small flat screwdriver unsnap back cover from switch panel to reveal circuit board fig El 2 Locate internal function switches fig 3 Push switches to lower position as shown fig These settings enable backlighting of flush switches and disable backlighting of VFS and VFP panel s Service switch which does not operate with older VacuFlush electronic flush toilets 4 Reass
4. e paper Do not AN flush wet wipes sanitary napkins condoms diapers razor blades paper cups 9 q cotton swabs food hair or liquids such as oils or solvents Clogging or damage to the toilet system may occur Note i Make sure all guests understand toilet operation before use 3 3 Indicator lights POWER INDICATOR POWER On the Dometic flush switch panel a steady green Power light indicates when electrical power to the toilet is activated TANK LEVEL INDICATOR The Dometic flush switch panel includes a Tank Level light to indicate holding TANK Hy LEVEL tank status if connected to appropriate tank monitoring system and when it should be pumped out When the light is yellow the tank is 3 4 full When the light is red the holding tank is full and electrical power to the toilet automatically shuts off to prevent overfill of the holding tank After the holding tank is emptied the light will turn off and electrical power to the toilet is restored 4 VacuFlush Toilet Operation with VES or VFP Flush Switch Dometic 4 1 Toilet system start up a FLUSH Turn on electrical power and water supply to toilet ADD Flush water through entire toilet system by flushing toilet five times press Flush switch and allow each flush cycle to complete until green light indicates system is ready for next 3 flush Each cycle takes about one minute FLUSH SERVICE DO NOT N WATER FLUSH
5. emble panel and install according to instructions in Section 1 2 ae PR 02 k ON CTS N J N Be Note i These instructions apply only to panels installed with OLDER Dometic and SeaLand electronic flush toilets It is not necessary to reset internal function switches installed with new toilets 1 2 Flush switch panel DB Dometic Taa POWER Dometic TE oKTo FLUSH ADD TANK WATER Taan A DO NOT FLUSH Pc N m SERVICE FLUSH VFS VFP models for VacuFlush toilets DFS DFP models for other SeaLand toilets Caution If replacing a previous electronic flush switch WITH ELECTRICAL POWER OFF be sure to disconnect wiring from old switch before installing new flush switch NEW INSTALLATION 1 Plan flush switch location so cable can reach toilet base circuit board Be sure cable cannot get wet 2 Using correct Dometic Vimar or Gewiss panel template see Section 5 mark center access and fastener holes Cut out square access hole to size fig 4 Make sure there is at least 2 inches 51 mm of clearance behind wall surface 3 Route flush switch cable from wall access hole to floor access hole at toilet base leaving about 12 inches 805 mm of extra cable at toilet 4 Attach cable to back of flush switch circuit board fig 4 then fasten flush switch bracket to wall with supplied screws fig 5 Snap Dometic Vimar or Gewiss cover plate onto bracket fig Ea at proper connection
6. light will turn off and electrical power to the toilet is restored D gt 3 RushFlush Toilet Operation with DFS DFP Flush Switch O Dometic 3 1 Toilet system start up POWER Turn on eletrical power and water supply to toilet system ears LEVEL N Press Flush switch once o Toss several sheets of toilet paper into bowl and repeat cycle The bowl should completely clear gt If tissue paper does not completely discharge from toilet bowl flow times for the rim and lower water jets may need to be increased On RushFlush toilet s water flow control module fig adjust water flow times to higher setting Repeat flush test after each adjustment to assure tissue paper discharges from toilet bowl 3 2 Normal toilet operation ADDING WATER TO TOILET BOWL Press Add Water switch until desired water level is achieved More water is usually A added only when flushing solids If switch is pressed too long water flow will shut off automatically to avoid overflow ADD WATER BACKLIGHTING To turn switch backlighting effect off or on push Add Water switch twice very quickly FLUSHING TOILET Press Flush switch then release it This activates a powerful water jet action that CW breaks up and discharges effluent from the bowl through the discharge loop and to the holding tank FLUSH DO NOT FLUSH FOREIGN OBJECTS CAUTION Flush only water bodily wastes and rapid dissolving tissu
7. oms diapers razor blades paper cups Wad a a cotton swabs food hair or liquids such as oils or solvents Clogging or damage to the toilet system may occur Note i Make sure all guests understand toilet operation before use 2 3 Changing flush modes MasterFlush toilets offer two flush settings to help manage water consumption Normal flush Uses 0 85 gal 3 2 liters per flush Adds water to bowl after every flush Dry Bowl flush Uses 0 45 gal 1 7 liters per flush Does not add water to bowl after flush To change from Normal to Dry Bowl flush setting press Flush switch for about five seconds When Power light begins flashing release Flush switch Flush mode has been changed to Dry Bowl setting Change mode to Normal flush by following the same procedure 2 4 Indicator lights POWER INDICATOR e POWER On the Dometic flush switch panel a steady green Power light indicates when electrical power to the toilet is activated TANK LEVEL INDICATOR The Dometic flush switch panel includes a Tank Level light to indicate holding TANK Ta l w LEVEL tank status if connected to appropriate tank monitoring system and when it should be pumped out When the light is yellow the tank is 3 4 full When the light is red the holding tank is full and electrical power to the toilet automatically shuts off to prevent overfill of the holding tank After the holding tank is emptied the
8. points see Section 6 back page 6 WITH ELECTRICAL POWER OFF connect wiring cable from the flush switch to the RJ45 connector on the circuit board of the toilet base fig 6 2 MasterFlush Toilet Operation with DFS or DFP Flush Switch ADB Dometic 2 1 Toilet system start up A Power 1 Turn on electrical power and water supply to toilet A TANK 2 Press Flush switch once After nine seconds of water flow actor macerator pump will start and run for about six seconds to clear bowl It will take about five seconds to refill bowl 3 Toss several sheets of toilet paper into bowl and repeat cycle The bowl should completely clear 2 2 Normal toilet operation ADDING WATER TO TOILET BOWL Press Add Water switch until desired water level is achieved More water is usually added only when flushing solids If switch is pressed too long water flow will shut off automatically to avoid overflow gt ADD WATER BACKLIGHTING To turn switch backlighting effect off or on push Add Water switch twice very quickly FLUSHING TOILET Press Flush switch down then release it This activates a powerful macerator pump that siphons water and waste from the bowl macerates and propels the effluent through the discharge line to the holding tank lt FLUSH DO NOT FLUSH FOREIGN OBJECTS CAUTION Flush only water bodily wastes and rapid dissolving tissue paper Do not flush wet wipes sanitary napkins cond
9. s 1 quart 0 95 liter per flush Adds water to bowl after every flush Dry Bowl flush Uses 1 pint 0 5 liter per flush Does not add water to bowl after flush To change from Normal to Dry Bowl flush setting press Flush switch for about five seconds When green OK to Flush light on status panel begins flashing release Flush switch Flush mode has been changed to Dry Bowl setting Change mode to Normal flush by following the same procedure 4 4 Indicator lights OK TO FLUSH INDICATOR OK TO A steady green OK to Flush light indicates when the toilet is ready to flush A FLUSH momentary flashing green light indicates when flush mode is changing continued on next page O DO NOT FLUSH INDICATOR DO NOT Ared Do Not Flush light indicate two possible toilet system conditions FLUSH 4 vacuum level in toilet system is not sufficient for complete flush 2 holding tank is full and should be pumped out When the red light is on electrical power to the toilet automatically shuts off to prevent possible overfilling of the holding tank 4 5 Service mode To clean the toilet bowl or perform other service that requires keeping the flush ball 3 open without running water use the Service switch SERVICE 1 Push the Service button for three seconds The steady backlight will change to a flashing light while the toilet is in Service mode 2 Perform the service operation After the Service operation is
Download Pdf Manuals
Related Search