Home

user manual engliSh

1. Preparation and Checks Before Use Ki Checking the Rear Cleansing Feature 3 e Cover the seat sensor with a piece of paper or cloth If the paper or cloth is black the occupied seat sensor may not function e Press the Cleansing button A A e Place a hand above the nozzle tip to block the sprayed water At this time water comes out from a point near the nozzle tips in preparation for operation e Press the STOP button B to stop the shower e Remove the paper or cloth B covering the seat sensor Check the other functions by referring to General Operation from page 17 of this Manual The toilet is equipped with a seat sensor which detects when someone is sitting on the seat The functions for front and rear cleansing as well as for drying cannot be activated when there is NO one sitting on the seat A WARNING Ensure the electrical outlet to which the power cord is connected is properly grounded as failure to do so may cause electric shock or damage This product should only be connected to a 120 VAC 60 Hz GFCl protected outlet Do not connect additional power cords to the toilet s electrical outlet as this may result in fire Preparation and Checks Before Use Our company recommends that you perform the following operations before using the seat unit for more comfort Adjusting the Spray Water Temperature e Press the Water temp button C
2. Never disassemble or modify this product as this may result in electric shock fire and or injuries In addition disassembly of the product will void the warranty If water is leaking from the seat unit or the water supply system disconnect the power plug from the outlet and close the water shutoff valve as this may result in electric shock fire or floor flooding If the seat unit power plug or power cord are damaged abnormal noise odor smoke high temperatures cracking or water leakage occurs disconnect the power plug from the outlet immediately close the water shutoff valve and have the part repaired Never use any defective parts as this may result in electric shock or fire 2 See Your Warranty Page This product comes with a limited warranty Be sure to thoroughly read the warranty statement which can be found on page 69 of this manual Keep your proof of purchase typically the sales receipt from your DXV by AMerican Standard dealer where it can be accessed easily The warranty period is 3 years from the date of purchase Read the warranty statement to clarify which items are covered under the warranty and which items are not covered under the warranty 3 Requesting Repairs STOP IF YOU HAVE ANY QUESTIONS OR PARTS ARE DAMAGED OR MISSING PLEASE DO NOT CONTACT OR RETURN THIS PRODUCT TO THE STORE PLEASE CONTACT YOUR LOCAL CUSTOMER SERVICE REPRESENTATIVE WE
3. Note e Do not apply excessive force when removing and installing the side covers as this could cause damage Low Water Pressure If the toilet has been used for a long period of time and flushing or cleansing functions seem to be getting weak clean the filters as described in the following procedure Generally the filters should be cleaned once every two years Cleaning the Filter 1 Close the water shutoff valve 2 Press the Flush Full or the flush buttons on the seat unit Wait for about 20 seconds before performing the next step 3 Disconnect the power plug from the outlet 4 Remove the side cover on the left side of the seat unit Page 51 5 Place a piece of cloth under the filter on the left side of the seat unit and remove the filter to drain the seat unit 6 Thoroughly wash each component in water to remove grime 7 Fully reattach the filter as shown in the diagram 8 Attach the side cover Page 51 9 Connect the power plug to the outlet 10 Open the water shutoff valve fully When using the toilet again Be sure to perform usage checks before use Page 14 Note Be careful not to damage the water supply hose when removing the filter A CAUTION e Close the water shutoff valve when removing the filter When installing the filter tighten it fully so there is no gap e Check that the O ring is free from foreign material
4. Assembling the Nozzle Guard 1 While the nozzle is retracted firmly press the two tabs into the slots on the base as shown in the diagram Press the Stop button to retract the nozzle when it is out Note Push the lugs until a click is heard Check that the guard is correctly assembled The guard has a top and bottom and must be assembled in the correct way Do not use excessive force as this could damage the guard Cleaning the Nozzle e The nozzle can be cleaned manually The Spray nozzle can be cleaned using either of the methods listed below e The nozzle can be cleaned using the Nozzle cleaning button on the remote control unit Cleaning the Nozzle with the Remote Control Unit e To clean the nozzle while using the toilet sitting on the seat using the remote control unit follow the procedure below 1 Press the Nozzle Cleaning button A The nozzle remains retracted inside the body and is cleaned for approximately 15 seconds This toilet is equipped with an auto cleaning function which cleans the nozzle and surroundings automatically before and after the rear cleansing rear cleansing mild or front cleansing function A Cleaning the Nozzle Manually e To clean the nozzle manually follow the procedure below 1 Turn off the Auto Clean B and Auto Seat Open C buttons This will disable the automatic lid and automatic
5. The water temperature can be set to any of six levels OFF water temperature and ranging from Low approximately 90 F 32 C to High approximately 104 F 40 C CAP aaa C Pressing the buttons alters the LCD display Adjusting the Seat Temperature e Press the Seat temp button D The seat temperature can be set to any of six levels OFF room temperature and ranging from Low approximately 82 F 28 C to High approximately 98 F 36 5 C ED D Pressing the buttons alters the LCD display Adjusting the Clock e Press the Hr or Min button E To advance the time on the clock in one hour or one minute increments press and release the Hr or Min button respectively To advance it rapidly press and hold the button for one second The accuracy of the clock is within 1 minute per month at room temperature approximately 77 F 25 C Pressing the buttons alters the LCD display Reference e This toilet is equipped with a seat heater auto off function that automatically turns off the seat heater when it is occupied to prevent low temperature burns Page 30 e The toilet seat is not warmed immediately our company recommends that you set the temperature 10 to 15 minutes before use in order to use the toilet comfortably General Operation 1 Auto Seat Open Function e Press the Aut
6. This will disable the automatic lid and automatic flush functions 2 Lift the seat lid and seat 3 Press the Nozzle Cleaning button C The rear cleansing nozzle extends and oscillates Water will automatically wash the nozzles lt To select the front cleansing nozzle for replacement gt Press the Nozzle Cleaning button D again The front cleansing nozzle extends and oscillates ig Note The nozzle tip cannot be replaced while a user is sitting on the toilet seat 4 Press the STOP button E The nozzle stops for approximately 5 minutes Replace the nozzle tip The nozzle retracts to its original position after 5 minutes 5 Turn the nozzle tip counterclockwise to align the replacement mark on the right of the nozzle tip with the nozzle center mark and pull out the nozzle tip as shown in the diagram on the right Pull the nozzle out slightly hold the back section of the nozzle with your hand and remove the tip Install a new nozzle tip as described in Assembling the Nozzle Tip Page 50 while the nozzle is stopped The above procedure can also be followed to replace the front cleansing nozzle tip Replacing the Nozzle Tip Assembling the Nozzle Tip If the nozzle retracts to its original position perform steps 2 to 5 in Removing the nozzle tip to expose the nozzle 1 Align the replacement mark on the right of the nozz
7. 4 Lift the right side of the seat lid to disengage it from the hinge pin on the toilet seat 5 Slightly tilt the toilet seat lid toward you and slide it to the left to remove it Note Do not use excessive force on the seat lid as this may damage it Do not open the toilet seat with the seat lid removed as this may cause toilet seat to become scratched or damaged e Do not use the toilet with the seat lid removed When the seat lid is lowered to the closed position and then removed the rear cleansing rear cleansing mild front cleans ing and dryer features do not operate when using the toilet Removing the Toilet Seat Lid for Cleaning Assembling the Toilet Seat Lid 1 Align the pin hole on the left side of the seat lid with the hinge pin on the seat and insert the pin into the hole 2 Lift the right side of the seat lid to set it with the hinge pin on the toilet seat 3 Turn the toilet seat lid release lever downward until a click is heard 4 Press the Power button A to turn the power on Check that the power LED is illuminated A Indicator Upper body sensor m Cleaning the Toilet Bowl Cleaning the Toilet Bowl Ceramic Parts e Clean the bowl with water or warm water using a soft brush or sponge dampened with neutral cleanser Note e Do not use chlorinated cleansers acidic cleansers or disi
8. Remote control za Allows the user to operate the toilet from a comfortable position Seat sensor Page 34 Detects the presence of a user and allows the cleansing function to operate Auto seat open Page 17 25 Automatically opens and closes the seat lid Auto flush Page 24 Automatically flushes the toilet after the user walks away uo Functions O Available Not available Comfort Functions Night light Page 29 Makes the toilet easy to find at night Seat heater auto Page 30 Turns the seat heater off when a user sits on the seat Turns the seat heater on OFF again when the user stands up Page 16 Displays the current time on the main panel LCD Reset function Page 33 Resets the settings to the factory defaults Cleaning Functions Easy clean seat Automatic bowl 5 The toilet bowl is fully rinsed during each flush cycle rinse Self cleaning Page 20 The nozzle tips are automatically washed before and after cleansing nozzle Removable toilet Page 41 42 The toilet seat lid can be removed for easy cleaning seat lid Removable Page 49 50 Both nozzle tips can be manually removed for either cleaning or replacement nozzle tips Removable Page 44 45 The guard that covers the nozzles can be removed for easy cleaning nozzle guard Power Saving Functions Advanced power Page 27 Power levels are increased to normal settings during regular usage and lowered save during periods of non use One touch power
9. Troubleshooting Seat Heating The toilet seat is not warm The toilet seat temperature drops when occupied for long periods Press the Seat temp button and adjust the temperature to the appropriate level The seat temperature is set too low The power save function is Cancel the power save function activated The seat heater auto off Cancel the toilet seat function is operating temperature auto off function Dryer The dryer does not work The air is not warm Change your sitting posture for example sit further back on the seat The seat sensor does not detect a user Your clothes mean that detection by the occupied seat sensor is difficult Allow the sensor to detect your skin Temperature may feel different according to conditions of use The warm air temperature conforms to the IEC standard IEC International Electrotechnical Commission Warm air stops suddenly before finishing The drying function has been ceed for minutes Press the Dryer button again f Press the Dryer button and The warm air temperature is adjust the temperature to the set too low appropriate level 62 Troubleshooting Deodorizer The deodorizer fan runs continuously The deodorizer fan does not operate Something is covering the Remove whatever is covering occupied seat sensor the sensor The deodorizer function is Turn on the automatic
10. flush functions B 2 Lift the seat lid and seat B C 3 Press the Nozzle Cleaning button Water comes out from a point near the nozzle tips for approximately 5 seconds The rear cleansing nozzle extends and oscillates in a short stroke Water is not sprayed during this cleaning function Note e The Nozzle Cleaning feature should be operated when the toilet seat is raised When the toilet seat is lowered the nozzle does not extend while it is being washed 46 Cleaning the Nozzle Cleaning the Nozzle Manually Continued 4 Clean the rear cleansing nozzle Since the nozzle moves in a short stroke the nozzle can be cleaned by simply applying a sponge to it The nozzle automatically retracts after approximately one minute When the Nozzle Cleaning button is pressed again after the nozzle retracts the rear cleansing nozzle extends again Reference If the nozzle guard comes off while cleaning the toilet refer to Assembling the Nozzle Guard Page 46 5 Press the Nozzle Cleaning button D The rear cleansing nozzle retracts and then the front cleansing nozzle extends 6 Clean the front cleansing nozzle Since the nozzle moves in a short stroke the nozzle can be cleaned by simply applying a sponge to it The nozzle automatically retracts after approximately one minute When the Nozzle Cleaning button is pressed twice after the
11. fuses batteries WARNING This warranty DOES NOT COVER any damages caused by the use of harsh cleaners These products can seriously corrode the product components This damage can cause leakage and property damage DXV by American Standard will not be responsible or liable for any damage caused by the use of in tank cleaners DXV by American Standard s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation including any costs of any surrounding material such as tile or marble DXV by American Standard is not responsible for any other incidental or consequential damages attributed to a product defect Some states or provinces do not allow the exclusion or limitation of implied warranties so this exclusion may not apply to you This warranty gives you specific rights You may have other statutory rights that may vary from state to state or province to province in which case this warranty does not affect such statutory rights 69 2014 AS America Inc DXV AMERICAN STANDARD How to register the warranty ENGLISH PLEASE COMPLETE DXV BY AMERICAN STANDARD WARRANTY REGISTRATION AND SAVE THIS WARRANTY INFORMATION IMPORTANT Registration of the toilet must be completed for this warranty to become effective Your registration will make it easier to service your product INSTRUCTIONS Register your toilet at www DXV com Please save your point of purchase
12. sale receipt IF YOU HAVE ANY QUESTIONS OR PARTS ARE DAMAGE OR MISSING DO NOT CONTACT OR RETURN THIS PRODUCT TO THE STORE CONTACT CUSTOMER SERVICE AT DXVCustomerCare DXV com OR TOOL FREE AT OUR GLOBAL HEADQUARTERS CUSTOMER SPARE COMPONENTS PAGE CAN BE FOUND AT www DXV com In the United States DXV by American Standard One Centennial Avenue Piscataway New Jersey 08855 Attention Director of Customer Care For residents of the United States warranty information may also be obtained by calling the following toll free number 800 227 2734 www DXV com 2014 AS America Inc gt AMERICAN STANDARD In Canada DXV by American Standard 5900 Avebury Road Mississauga Ontario L5R 3M3 Canada Toll Free 1 800 387 0369 Local 905 306 1093 Fax 1 800 395 1498 www DXV ca In Mexico DXV by American Standard Via Morelos 330 Col Santa Clara Coatitla Ecatepec Estado de M xico 55540 Toll Free 01 800 8391200 www DXV mx GCW 1333 US ASB 14030
13. CAN TAKE CARE OF ANY QUESTION OR ISSUE YOU MAY HAVE m Within the warranty period When requesting warranty service please have the following information available m Outside the warranty period If service is requested outside of the warranty period the cost of service is responsibility of the product owner Service charges include a technical service fee travel expenses and parts costs a Details you will be asked 1 Your contact information e g name address phone 2 Product model name number and color See the product label on the side of the body 3 Date of installation 4 The reason for requesting service 67 Specifications Grade D28000AS416 XXX Rated power 120 VAC 60 Hz Rated power consumption 1300 W Power saving type Instant system Suitable Minimum pressure 14 5 psi 0 10 MPa or more when water flow is 4 8 GPM 18 L min or more tap water pressure Maximum pressure 108 83 psi 0 75 MPa static water pressure range Operating temperature range 32 F 0 C 104 F 40 C Product dimensions 16 s 415 mm W x 25 635 mm D x 21 7 s 555 mm H Product weight Approx 70 4 Ib 32 kg Seat unit Approx 22 Ib 10 kg Toilet Approx 48 4 Ib 22 kg Power cord Effective length 3 28 ft 1 0 m with earth 1 32 gal 5 L for full flush
14. OTOOTO NANNAN DIOGO G9 000 0 Safety Precautions AN WARNING Disconnect the power plug periodically and clean it with a dry cloth as dust accumulated on the power plug may cause fire Wait for about 10 seconds before inserting the power plug again Completely connect the power plug as failure to do so may cause electric shock or fire Do not damage bend excessively twist bind or place heavy objects on the power cord Doing so may result in electric shock or fire Do not use a loose outlet as this may cause electric shock or fire Ensure the electrical outlet to which the power cord is connected is properly grounded as failure to do so may cause electric shock in the event of a seat unit failure or short circuit If water is leaking from the seat unit or the water supply system disconnect the power plug from the outlet and close the water shutoff valve Failure to do so may cause electric shock fire or floor flooding Never operate this product if it has a damaged cord or plug if it is not working properly if it has been dropped or damaged or dropped into water Return the product to a service center for examination and repair If the seat unit power plug or power cord are damaged or not working properly through abnormal noise odor smoke high temperature cracking or water leakage or if the plug is loose in the outlet disconnect the power plug from the outlet immediate
15. Operation To flush the toilet manually Press the flush button on the seat unit A short beep sounds from the seat unit and the toilet is flushed Note e In the event of a power failure flush the toilet as described in Flushing the Toilet Manually Page 37 e When too much toilet paper is used it may not be flushed completely when the Flush Partial button is used Use either the Flush Full button on the remote control or the flush button on the seat unit Flush delay setting When the user is standing Full flushing versus partial flushing In full auto flushing mode flushing When a user stands in front of the In AUTO CLEAN mode full flushing is begins approximately 6 seconds toilet for 6 seconds or longer with the performed when a user occupies the toilet after the user stands up The seat opened partial flushing begins 1 seat for 50 seconds or longer Partial flushing delay time can be changed to second after the user leaves the toilet is performed when the user occupies the approximately 2 10 or 15 seconds If the user closes the toilet seat toilet seat for less than 50 seconds Page 33 lid before leaving the auto flush If any of the cleansing functions are used function will not operate full flushing is performed even if the seat is occupied less than 50 seconds General Operation 6 Auto Close Function The toilet seat lid closes approximately 1 minute after the user leaves the toilet It do
16. Seat Unit 1 Close the water shutoff valve to stop water supply 2 Press the Flush Full button or the flush button on the seat unit Wait for about 20 seconds before performing the next procedure 3 Remove the side cover on the left side of the seat unit Page 51 4 Place a piece of cloth under the filter on the left side of the seat unit and remove the filter to drain the seat unit Note Be careful not to damage the water supply hose when removing the filter Preventing Freezing 5 Press the Power save A and Auto Clean B buttons simultaneously for 2 seconds A Drain the remaining water in the seat unit for approximately 15 seconds 6 Thoroughly wash the filter and O ring in By water to remove grime 7 Fully reattach the filter 8 Attach the side cover Page 51 9 Check that no water leaks from the water shutoff valve e When using the toilet again Be sure to perform usage checks before use Page 14 A CAUTION Close the water shutoff valve when removing the filter e When installing the filter tighten it fully so there is no gap Check that the O ring is free from foreign materials before attaching the filter as failure to do so could result in water leakage and flooding Connecting Disconnecting the Water Supply Hose Disconnecting the Water Supply Hose Remove the clip ring be
17. electric shock or fire Do NOT disassemble or modify this product Disassembly may result in electric shock fire and or injuries In addition disassembly will invalidate the product s warranty This product should only be connected to a potable water supply line Failure to do so will cause problems in the operation Do not use outdoors or operate where aerosol spray products are being used or where oxygen is being administered Connect this product to a properly grounded outlet only See Grounding Instructions in page 12 If connection is made to a potable water system the system should be protected against backflow Keep the cord away from heated surfaces Example Panel Heater Never use this product while sleeping or drowsy Never drop or insert any object into any opening or hose Never block the air openings of the product If lint or hair etc is stuck in the air opening remove it immediately When this product is used by children the elders or persons with limited mobility our company recommends close supervision to avoid improper operation of the product MSR RORORRES RRO REROR REPRO LORE DIOGO G00 0000 Safety Precautions AN CAUTION For care of the plastic parts our company recommends the use of a mild liquid all purpose cleaner Avoid using abrasive products such as powdered cleansers and chlorine based products such as bleach as these products c
18. must be plugged into an outlet that is properly installed and grounded Z DANGER Improper use of the grounding plug can result in a risk of electric shock If repair or replacement of the cord or plug is necessary do not connect the grounding wire to either flat blade terminal The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire Check with a qualified electrician or serviceman if the grounding instructions are not completely understood or if in doubt as to whether the product is properly grounded Figure 1 f GROUNCED OUILeT we GROUNDING PIN _ _ ADAPTER a METAL SCREW GROUNDED E OUTLET BOX T TAB FOR B GROUNDING screw O gt CAD Handling Precautions Do not expose the toilet to direct sunlight as this may cause discoloration or the remote control or body sensor may malfunction Do not open or close the toilet seat or lid roughly as this may result in damage to either of these parts Do not splash water or cleanser onto the remote control as this may cause it to fail Do not operate the remote control with wet hands as this may cause damage Do not use toilet deodorizer on the plastic parts If the plastic parts are splashed with the deodorizer wipe it off immediately Otherwise gloss may be lost Do not block the warm air or heater outlets as this may ca
19. nozzle retracts the front cleansing nozzle extends again 7 Press the Nozzle Cleaning button The front cleansing nozzle retracts and then the dryer duct extends 8 Clean the dryer duct Wipe the dryer duct with a soft cloth or the similar The dryer duct automatically retracts after approximately 5 minutes 9 Press the Nozzle Cleaning button The dryer duct retracts Note e Be very careful not to press the STOP button on the remote control when operating the Nozzle Cleaning button as the nozzle may stop or retract Cleaning the Nozzle To Stop the Motion of the Nozzle 1 Press the STOP button E The nozzle stops The nozzle stops for approximately 5 minutes and then automatically retracts In this case when the Nozzle Cleaning button is pressed again after the nozzle retracts the nozzle extends again 2 Press the STOP button again The nozzle retracts Note Do not apply excessive force to the nozzles as this may cause failure e Do not pull or push the nozzles The nozzle will not be retracted and failure may occur When you pull or push the nozzles by mistake disconnect the power plug from the outlet wait for about 10 seconds and connect the power plug to the outlet again 48 Replacing the Nozzle Tip Removing the Nozzle Tip 1 Turn off the Auto Clean A and Auto Seat Open B buttons
20. nozzles in preparation to spray warm water It may take a short time to warm the water in winter or in cold regions Water comes out either immediately after sitting down on the toilet seat or before and after cleansing This is a requirement to achieve the function and so the user should not regard this as a problem Page 35 General Operation For front cleansing This spray nozzle is designed for women s use only e Press the Bidet button B Water will drip from the nozzle This washes the nozzle before use The nozzle extends and water sprays e Press the STOP A button The spray will stop and the nozzle will retract To adjust the water pressure Press or on the Spray Strength button C The water pressure can be adjusted to any of six levels Select the water pressure as desired To change the cleansing mode Press the Bidet button B a second time during front cleansing Pressing Bidet during front cleansing alters the mode Once the cleansing is stopped the cleansing mode starts with front cleansing when Bidet is pressed Front cleansing gt Oscillating spray gt Oscillating spray super The nozzle moves back and The nozzle moves back and forth forth to wash a wide range over a short span for more thor ough cleansing Note e f the toilet is flushed while the front cleansing function is in use then the front cleansing function
21. save Page 26 Power levels are reduced for an 8 hour period 8 hours Power button iz This product can be turned off during long periods of non use ECOS This product uses 1 3 gallons 5 liters for a full flush and 0 92 gallons 3 5 liters for a partial flush Hyper Clean Both the toilet bowl and the seat unit have antibacterial properties that allow for surface easy cleaning Safety Precautions When using electrical products especially when children are present basic safety precautions should always be followed including the following Please read the following Safety Precautions thoroughly before use Failure to heed these precautions may result in serious consequences under some circumstances Each of these items are extremely important for safety and should be strictly observed This product should be used only as described in this manual AN Means Be careful This is used together with WARNING or CAUTION in order to draw users attention Carefully read and strictly observe the description DANGER Indicates an imminently hazardous situation which if not avoided could result in death or serious injury WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION Indicates a potentially hazardous situation which if not avoided could result in minor or moderate injury or in damage to product or other property AN DANGER To reduce
22. setting is complete To reset the setting press the Seat temp button and Auto Clean buttons simultaneously again for 2 seconds A beep sounds when the setting is complete C B Comfort Features Preventing Low temperature Burns Seat Heater Auto OFF This product is equipped with a safety feature seat heater auto off that prevents low temperature burns When the user sits on the seat the seat heater is automatically deactivated When the user stands up the seat heater is reactivated The default setting for this safety feature is OFF To activate this feature follow the steps below Press the Seat temp A and Power save B buttons simultaneously for 2 seconds A short beep sounds when the setting is complete To cancel the seat heater auto off function Press the Seat temp A and Power save B buttons simultaneously again for 2 seconds A beep sounds when the setting is cancelled Comfort Features Lowering the Water Pressure For users who are sensitive to water pressure the water pressure setting for the rear cleansing rear cleansing mild and front cleansing can be adjusted below the normal range The default setting for this feature is OFF To activate this feature follow the steps below Press the Seat temp C and Nozzle Cleaning D buttons simultaneously for 2 seconds A short beep sounds when the setting is complete S If the tap water QY press
23. tem perature burn For this reason our company recommends setting the dryer temperature to Low during use BORER ROO rne enn ennennvrrvrnrcrirncn dE Safety Precautions AN WARNING Please observe the following precautions when inserting batteries for the remote control e Place the battery in the correct direction aligning the positive and negative terminals as indicated inside the battery compartment If the toilet will not be used for a long period of time remove the batteries from the remote control Remove any dead batteries from the remote control immediately Dispose of all dead batteries according to local regulations Keep batteries out of the reach of children In the case of batteries being swallowed seek medical attention immediately e Do not use old and new batteries together in the remote control Do not do any of the following while handling batteries e Do not let the batteries have contact with metal items such as necklaces hair pins and do not store such items with the battery Do not mix old and new batteries or different types of batteries Do not heat or disassemble the battery or place it in water or fire as the battery may leak and cause fire If there is any possibility of the water freezing be sure to activate the antifreeze function Damage due to freezing may cause fire or flooding Do not install this product in a humid area such as a bathroom as this may cause
24. the toilet seat and seat lid from closing forcefully a damping mechanism is provided Note that the toilet seat or seat lid may be damaged if these are closed roughly or too forcefully These close slowly only when the power is turned on Other References The body sensor allows you to open the seat lid without using your hands This toilet is equipped with an upper body sensor This detects when a person enters the toilet room and opens and closes the toilet seat lid automatically The upper body sensor detects the motion of a person The sensor cannot detect the user if they stand to the side in front of the toilet or away from the toilet The body sensor may not function correctly if it is dirty In this case wipe the sensor with a soft clean cloth The sensor may malfunction making the toilet seat lid automatically open due to heat from direct sunlight Ther fore avoid direct sunlight Shower in winter When water temperature is extremely low in winter for example the water pressure of the shower may become weaker or it may take longer than usual before the water is sprayed If You Have These Problems Water comes out from a point near the nozzle tips Water comes out from a point near the nozzle tips immediately after the toilet seat is occupied or before and after cleansing This is normal operation This is done to o prepare the nozzle for use ND If water comes out under ci
25. will stop The front cleansing function cannot be started while flushing the toilet Front cleansing Equipped with an auto stop function which terminates cleansing after 2 minutes However when the oscillating spray is activated while the front cleansing function is performed the cleansing time will be lengthened by 2 minutes This will automatically stop after the cleansing has been performed for up to 6 minutes in total 21 General Operation Massage Function During rear cleansing or rear cleansing mild the massage function alternates between a strong spray and a gentle spray to provide a massage effect e Press the Massage button A during rear cleansing or rear cleansing mild e Press the Massage button A again to end this feature Nozzle Position The nozzle position can be adjusted backwards and forwards during rear cleansing rear cleansing wild or front cleansing e Press the or button on the Nozzle Position button B The nozzle position can be adjusted to any of five different settings There are two settings in the front a center posi tion which is also the initial position and two in the rear If the user stands up the nozzle position will return to the default setting General Operation 4 Using the Dryer Dryer Function Warm air is blown to dry the area washed by the shower e Press the Dryer button B The air t
26. 0 92 gal 3 5 L for partial flush ae el and 0 92 gal 3 5 L for urination by male Floor drain or refitting o Water supply method Uses existing water supply line Warm water supply system Inline ceramic heater for continuous warm water Power cleansing Rear cleansing 0 10 0 13 GPM 0 36 0 50 L min 6 adjustable levels when the water pressure is 29 02 psi 0 2 MPa ToN Mild cleansing Rear cleansing mild 0 10 0 13 GPM 0 36 0 50 L min 6 adjustable levels when the water pressure is 29 02 psi 0 2 MPa Cleansing Front cleansing 0 10 0 13 GPM 0 36 0 50 L min 6 adjustable levels when the water pressure is 29 02 psi 0 2 MPa Water temperature Water temperature Approx 90 F 32 C 104 F 40 C 6 User defined settings Heater capacity 1200 W Safety device Temperature fuse thermostat and flow rate sensor Air flow Rate 71 CFM 0 2 m min Drying Air temperature Range Room temperature Approx 104 F 40 C 131 F 55 C 3 User defined settings 3 with g warm air Heater capacity 230 W 8 Safety device Temperature fuse When used Room temperature and in the range of approx 82 F 28 C 98 F 36 5 C 6 User defined settings Surface temperature When the advanced power save function is activated Room temperature and in the range of approx 81 F 27 C Seat 86 F 30 C heating When the one touch power save 8 hours is activated Room temperature Heater capacity 48 W Safety device Temperature fuse Deodo
27. ATIONS wintieccsscsccsecccsccerssascccansnnedensansnceenenec 67 Optional Parts ccceececsctscisccdccssaceseseseccesssavesssacecdexeece 68 AT200 Features This product is designed so that people such as elderly persons persons with limited mobility or illness and children can use it without assistance To ensure proper usage of this product please read this User s Manual carefully before using it a Toilet seat lid b Seat unit c Indicator refer to the details below d Upper body sensor e Flush button f Power plug g Water shutoff valve h Open close handle i Water supply hose j Side cover k Seat sensor I Toilet seat lid release lever m Nozzle guard n Warm air drying duct o Nozzle for rear cleansing p Bowl q Nozzle for front cleansing r Toilet seat s Toilet e Upper body sensor The filter is located on the left side of the seat when viewed from the front The filter removes debris from the tap water Close the water shutoff valve before removing the filter A small amount of water may spill out when removing the filter so place a piece of cloth or similar on the floor Page 52 Water Shutoff Valve CLOSE Use the open close handle shown on the left to stop the supply of water to the toilet Always set the handle to the open position when using the toilet N3dO kos La OC 0000000 Tl AT200 Features Remote Control Unit 1 Main Panel Re
28. AUTO CLEAN k o Seat temperature indicator l d AUTO SEAT OPEN PY ama p p Dryer temperature indicator MII m M O Dh l A Reference e When the power button on the remote control is turned off OFF is displayed on the LCD Functions Rear cleansing Page19 Provides rear cleansing with a strong spray deer ang Page 20 Provides rear cleansing with a gentle spray ae age 19 20 Moves the nozzle back and forth to wash a wide range Oscillating Page 19 20 Moves the nozzle back and forth over a short span for a more thorough cleansing spray narrow Front cleansing Page 21 Provides front cleansing for women through a separate nozzle y aoa Page 21 Moves the nozzle back and forth to wash a wide range Oscillating Page 21 Washes an extended range spray super Nozzle position adjustment Page 22 Moves the nozzle to the desired position Water pressure Page 19 21 Adjusts the water pressure as desired Massage Page 22 Alternates the water pressure between two levels Comfort Functions tensors gt pesosa noero E D a o D D an 2 o co D N i 2 v o pe Temperature Page 16 Adjusts the water and seat temperature control Warm air dryer Page 23 Dries the user after front and or rear cleansing Deodorizer Page 18 Eliminates toilet bow odors Aeda j Page 28 Provides a more powerful deodorizing function
29. DXV ENGLISH AMERICAN STANDARD AT200 USER MANUAL D29020CS416 XXX SEAT amp BOWL COMBINATION CWH D23020CS11S XXX BOWL CWH D28000AS416 XXX SEAT BODY UNIT CWH Canvas White 415 Thank you for purchasing this product After reading this manual please keep it in a place where you can refer to it easily BE SURE TO FOLLOW THE SAFETY PRECAUTIONS Failure to follow the safety precautions may result in serious accidents in some circumstances Each of these items are extremely important for safety and should be strictly observed In the event that an accident occurs as a result of improper usage DXV by American Standard will assume no responsibility for damages 2014 AS America Inc Contents SATIS Features siciicsidctenidtscccenistianiscieaxceussiassecciess 2 Operation O Preparation and Checks Before Use 14 1 Checking the Water Shutoff Valve 1 14 2 Connecting the Power Plug to the Outlet 2 14 3 Checking the Rear Cleansing Feature 3 15 4 Adjusting the Spray Water Temperature 16 5 Adjusting the Seat Temperature 6 Adjusting the ClOCK occ O General Operation wees 1 Auto Seat Open Function 2 Auto Deodorizing Function 3 Front and Rear Cleansing 4 Using the Dryer oo cc ccccescessseseseeeees 5 Flushing the Toilet 6 Auto Close FUNCTION cece sees eee eereee Useful Functions O Pow
30. an damage the anti bacterial properties of the plastic components A Toilet cleanse Check that the clip ring is firmly attached to the water supply hose If the clip ring is not firmly attached the water supply hose may come off resulting in water leakage When using the filter please observe the following e Close the water shutoff valve when removing the filter e When installing the filter tighten it fully so there is no gap e Check that the O ring is free from any debris before attaching the filter Failure to follow these instructions may result in water leakage and flooding Do not bend or crush the water supply hose as this may result in water leakage and flooding Do not climb on top of the toilet seat lid or seat unit as these may break resulting in injury If the toilet seat or body cover becomes damaged contact our company for repair instructions Do not place your weight on or climb on the water shutoff valve as this may result in water leakage and flooding Do not apply any impact to the clip ring or pull it when cleaning the toilet as the clip ring may break and the water supply hose may come off resulting in flooding w Safety Precautions AN CAUTION Only connect the toilet to tap water Otherwise this may cause corrosion inside this product resulting in electric shock fire or inflammation of skin This product should be supplied with a cold w
31. ashes disconnect the power plug from the outlet and contact our company for service No water is supplied to the seat unit Suspended water supply closed water shutoff valve If the power LED still flashes after turning the Power button off there is a failure Disconnect the power plug from the outlet and contact our company for service Turn off the antifreeze heater When the water temperature exceeds 104 F 40 C the safety device is activated to stop operation There is a problem with warm water toilet seat drying function and or cleansing motor An antifreeze heater is provided for pipes such as the water supply hose This is not a problem The toilet is designed so that the rear seat bumper float free Use the toilet as usual All functions whose settings were changed as described in Useful functions are reset to their default setting Press the Water temp button and Seat temp buttons simultaneously for 2 seconds After sales Service 1 Before Requesting Professional Repairs If problems can not be solved by following the steps on page 60 contact your local customer service representative e If you have additional questions that are not addressed in the user s manual e f the power cord is damaged or the power cord is loose in the outlet e The outlet or power cord is overheating If the above condition is left as it is unexpected accidents may occur Be sure to consult us
32. ater line only as supplying it with a hot water line may damage its internal components If cracks appear anywhere on the toilet bowl do not touch the cracked areas Contact our company for instructions on how to replace the bowl Do not lean back against the toilet seat lid as this may damage or break the lid Do not expose the toilet to any force or impact as this may cause product damage injuries and water leakage Regularly check the area around pipes for water leakage If you are not going to be using this product for a long period of time close the water shutoff valve and drain the water from the toilet In addition disconnect the power plug from the outlet Page 55 for more information Disconnect the power plug from the outlet during cleaning Failure to do so may cause electric shock Ensure the power is turned on when using the nozzle cleaning function If it is necessary to modify the electrical wiring or plumbing our company recommends that such work should be performed by a licensed contractor Take care that children the elderly or persons with limited mobility do not fall when using this product They may be injured or damage the device When a small child is using the toilet set the Auto Seat Open switch on the remote control to the OFF position On rare occasions the seat sensor may not be able to detect the presence of a small child In such a case the toilet lid may s
33. ay detect a user and flush the toilet or close the toilet seat or lid A WARNING may cause electric shock or fire Do not splash water or liquid cleaners directly onto the seat unit or power plug as this A CAUTION all purpose cleaner of the plastic components For care of the plastic parts our company recommends the use of a mild liquid Avoid using abrasive products such as powdered cleansers and chlorine based products such as bleach as these products can damage the anti bacterial properties Cleaning the Toilet Seat and Lid Cleaning the Toilet Seat Lid and Covers Plastic Panels Dampen a soft cloth and wipe the surfaces Our company recommends cleaning the toilet bowl frequently to prevent dirt build up on the toilet surfaces Additionally do not use a dry cloth or toilet paper to wipe the surfaces as this could result in scratches Wiping with a damp cloth also prevents static electricity which can attract dust particles resulting in blackish contamination Removing the Toilet Seat Lid for Cleaning The seat lid can be removed easily This is useful when cleaning the hinge that is normally hidden or cleansing the whole seat lid Removing the Toilet Seat Lid 1 Press the Power button A to turn the power off Check that the power LED is not illuminated 2 Open the seat lid 3 Turn up the toilet seat lid release lever
34. battery indicator starts flashing Periods of Non use In the following cases be sure to drain the toilet according to the procedures below and disconnect the power plug from the outlet e When the toilet is not used for extended periods of time such as when you are away as the water could become dirty and cause clogging e If the toilet is installed in a vacation home that is not being used drain the water from the toilet The temperature in an empty house can drop lower than expected causing the water in the toilet to freeze Draining the Toilet 1 Close the water shutoff valve 2 Press the STOP button or the flush button on the seat unit Wait for about 20 seconds before performing the next step 3 Remove the side cover on the left side of the seat unit Page 50 4 Place a piece of cloth under the filter on the left side of the seat unit and remove the filter by turning it clockwise to drain the seat unit Note Be careful not to damage the water supply hose when removing the filter 5 Press the Auto Clean A and Power save B buttons simultaneously for 2 seconds B Drain water remaining in the seat unit for approximately 15 seconds 6 Thoroughly wash the filter and O ring in A water to remove grime 7 Fully reattach the filter by turning it counterclockwise as shown in the diagram 8 Attach the side cover Page 51 9 Check that no water leaks fro
35. ediately after a user leaves the toilet seat x A short beep sounds when the setting is complete 7 B A To cancel the automatic drain function Press the Power save button and Auto Clean buttons simultaneously for 2 seconds A beep sounds when the setting is canceled A CAUTION If there is any possibility of the water freezing be sure to activate the anti freeze function as damage due to freezing may cause fire or flooding Preventing Freezing Intermittent Flushing Method Water in the seat unit is drained every 3 minutes to prevent water in the seat unit from freezing The toilet is flushed every 6 minutes to prevent water in the toilet from freezing 1 Press the Massage C and Nozzle Cleaning D buttons simultaneously for 2 seconds C Water is drained from the seat unit every 3 e minutes for approximately 1 minute to prevent water from freezing while the toilet is not used The toilet is flushed every 6 minutes Water is not drained when the seat is occupied Once the cleansing is stopped the cleansing mode starts with rear cleansing when SHOWER is pressed D Sze To cancel the intermittent flushing Press the Massage and Auto Clean buttons simultaneously for 2 seconds A beep sounds when the setting is canceled To prevent remaining water in the seat unit from freezing drain water according to the procedure given below Draining the
36. emperature can be adjusted to any of three levels The deodorizer temporarily stops when drying is performed Set the remote control in the holder and press the Dryer button e Press the STOP button A to stop drying Wipe away any excess water with toilet paper The dryer function has an auto stop feature that will terminate drying after 4 minutes of continuous use To change the air temperature Press the Dryer Temp button C again while drying By pressing this button the warm air temperature is changed The temperature can be adjusted in a cycle from Low to Mid and High as displayed on the LCD and shown in the diagram below m _ _ oe _ oo Low Mid High Reference e Use a small amount of toilet paper to wipe away excess water before using General Operation 5 Flushing the Toilet Auto Flush Function The AUTO CLEAN button is displayed on the LCD The toilet is automatically flushed when the user stands up e Activate the Auto Clean button A To deactivate the full auto flushing function Deactivate the Auto Clean button A The AUTO CLEAN button indicator on the LCD disappears AUTO CLEAN G AUTO SEAT OPEN G Remote Control Flush Function To flush the toilet using the remote control Press the Flush Full B and the Flush Partial C buttons accordingly Full Flushing by Manual
37. ensor or remove any item that may be blocking the sensor The seat and lid open and close repeatedly even The seat sensor is dirty though no one is near the toilet The sensor is exposed to direct Do not expose the sensor to sunlight direct sunlight The toilet seat and seat lid remain open Clean the sensor or remove any item that may be blocking the sensor The upper body sensor is blocked or dirty Clean the sensor or remove any item that may be blocking the sensor 64 Troubleshooting Miscellaneous There are water drops on the underside of the toilet and water shutoff valve A gurgling sound is emitted from the seat unit When e The power plug is connected to the outlet e The Power button is turned on e The rear cleansing rear cleansing mild or front cleansing stops The power LED is flashing The rear seat bumper at the back of the toilet seat are not attached to the toilet To reset all settings to their default settings Frequently wipe water drops Also ventilate the toilet room adequately Humidity is high forming condensation This is not a problem It is the sound the motor generates when the toilet is operating normally There is no problem as long as the water water pressure and or nozzle position can be adjusted k D After supplying water open the water shutoff valve and conduct a trial operation If the power LED still fl
38. er SAVE FUNCTION cccccsccsesecsecseeseeseeseens 26 O Deodorizing FUNCTION wiccecccccscscseeseeseeseetens 28 O Night Light FUNCTION cee seeeteesetseseeeeseees 29 Comfort Features sainia 30 Preventing Low temperature Burns Seat Heater Auto OFF ues sce seeceeees 30 Lowering the Water Pressure wuss 31 Adjusting the Auto Flush Function 52 Muting the Signal Reception Sound 32 Restoring the Default Settings wu 33 Storing the Settings ccc cecccccscsesesecsscssesesseseees 33 Other References sicccseiseciccscssscssiscsassenssscsesancceccess 34 Manual Toilet Flushing sssssssssnsnnnnnnnnnnneennnnnnnnnn 37 Cleaning and Maintenance O Cleaning and Maintenance uuu 38 O Cleaning the Toilet Seat and Lid 40 o Removing the Toilet Seat Lid for Cleaning 41 O Cleaning the Toilet Bowl Ceramic Parts 43 O Cleaning the Nozzle Guard sssi 44 O Cleaning the Nozzle oc cccccseesseetseeeeeeees 46 O Replacing the Nozzle Tip cece 49 Oo Removing the Side Covers uo 51 O LOW Water Pressure ccccccsccecsssssseesrerees 52 O Low Battery Indicator s sssssssssesisisirirresesesesn 53 O Periods of NON USC ceccccstsccssesceetscesseseeeeees 54 O Preventing Freezing s s sssssssssssisisisirirreseseersrsns 55 o Connecting Disconnecting the Water SUPPIY HOSE siponi aaa 58 Troubleshooting ssssssssnnnnnnnneenennnnnnnnnnnnnnnnnnnnnnn 60 After sales Service ssssssssnnnnneneeeeenennnnnnnnnnnnnnnnnn 66 SPECIFIC
39. es not close when the Auto Seat Open button is turned off The upper body sensor detects the motion of a person and automatically opens and closes the toilet seat lid Note Do not manually obstruct stop or move in opposite direction the toilet seat or lid These activities may damage or cause the auto close function to malfunction To manually open and close the toilet seat lid Press the Auto Seat Open button A to deactivate function The AUTO SEAT OPEN button on the LCD disappears Note e Gently move the toilet seat lid when opening or closing it manually as excessive force may damage or cause malfunction T i z Z 7U To open and close the toilet seat with the remote control Press the Open Close button B Pressing OPEN CLOSE alternates opening and closing of the seat General Operation The power save function includes two functions for saving power one touch power save 8 hours and advanced power save always on Using these functions together will save more power The power saving functions are set to OFF in the default settings One Touch Power Save 8 hours When the ONE TOUCH POWER SAVE button is pressed the water and seat heaters are turned off for 8 hours Set This reduces power consumption during times when pe ee te 001G 001809 20 99 10 00 the toilet is not used e g during the night The original power settings will be resto
40. fore disconnecting the water supply hose 1 Insert a flat screwdriver into the gap The clip ring is designed so that the locking tab catches the other end of the ring F 2 Press the screwdriver down as shown in the diagram o e et eee 3 Push the screwdriver forward to release the locking tab Lightly twist the screwdriver to push it forward easily Connecting Disconnecting the Water Supply Hose Connecting the Water Supply Hose 1 Connect the water supply hose with the water shutoff valve 2 Close the clip ring until it clicks as shown in the diagram below After the clip ring is attached turn it to check that it is firmly secured Troubleshooting In many cases problems can be easily corrected Please check the following items before placing a service call If a problem cannot be corrected after checking the items below please contact our company for service All Functions Check for a power failure or tripped breaker or other probable cases Electricity is not supplied to the outlet Press the Power button to turn on the power LED on the seat unit indicator The Power button is off POWER LED No functions Fully connect the power plug operate the The power plug is not to the outlet Wait for about 10 power LED is not connected to the outlet seconds before connecting the illumi
41. le tip with the center mark of the nozzle completely insert the nozzle tip and turn it clockwise as far as possible as shown in the diagram on the right Hold the back section of the nozzle with your hand to attach the nozzle tip Note Do not damage the O ring of the nozzle as this may cause water leakage 2 Check the alignment Check that the center mark of the nozzle is aligned with that of the nozzle tip as shown in the diagram on the right Note e Inappropriate engagement may cause failure and may affect the angle of the water spray 3 Press the STOP button F to return the nozzle to its original position Removing the Side Covers The side covers can be removed easily Remove them when cleaning the rear side of the toilet and hidden areas on the floor Removing the Side Covers 1 Disconnect the power plug from the outlet 8 6 A 2 Remove the cap Remove the flat head screw using a Phillips screwdriver 3 Slowly pull the bottom of the side cover toward you and disconnect the clip from the clip holder 4 Slowly pull the side cover downward and disconnect the lug from the slot on the seat unit Installing the Side Covers To install the side covers reverse the removing procedure but check that the covers are firmly assembled before connecting the power plug
42. lose the toilet seat Note e Avoid direct sunlight as this may cause the sensor to malfunction and the toilet seat lid to automatically open General Operation Pa Auto Deodorizing Function 1 Deodorizing starts when the toilet seat lid opens When the toilet seat opens the deodorizer fan is activated in full power mode 2 The deodorizer operates in normal operation while the user is sitting on the seat The deodorizer fan changes to power mode 3 Deodorizing starts when the user stands up The deodorizer fan increases output again to full power mode 4 Deodorizing stops The deodorizer fan automatically stops one minute after the user stands up e To disable the automatic deodorizing function Press the Water temp C and Nozzle Cleaning D buttons simultaneously for 2 seconds A beep sounds when the setting is complete Press the Water temp and Nozzle Cleaning buttons simultaneously for 2 seconds to activate the automatic deodorizer again A short beep sounds when the setting is complete General Operation Ki Front and Rear Cleansing For rear cleansing e Press the Cleansing button B Water will drip from the nozzle This washes the nozzle before use The nozzle extends and water sprays e Press the STOP button A The spray will stop and the nozzle will retract To adjust the water pressure Press or on the Spray Strength button C The water p
43. loth appropriate size covers toilet Use a soft foam sponge Nozzle tips Toilet brush Use a brush with soft bristles Toilet bowl non abrasive Use to prevent rough skin forming on hands Rubber gloves Fold up the edges of gloves to prevent water and cleanser entering Cleanser tem Description Location Neutral toilet cleanser Removes yellowish and or blackish 7 f Ceramic parts Non abrasive cleanser contamination from the toilet bowl The toilet bowl has an antibacterial surface finish called Hyper Clean This is an extra fine grazing process that creates a smooth durable surface that is easier to clean than conventional glaze In order to maintain the surface finish our company recommends that the cleansers listed below should not be used to clean this product e Chlorinated type alkali cleansers e Abrasive cleansers e g powdered cleansers e Abrasive brush Cleaning and Maintenance Places to be cleaned and types of contamination Toilet seat lid and cover Page 40 Dust finger marks and urine stains Narrow gap between the toilet seat and lid Page 41 Dust and urine stains Nozzle guard Page 44 Water residue and urine stains Nozzle Page 46 Water residue and urine stains Toilet bowl Page 43 Mold bacteria and mildew Note e Deactivate the AUTO CLEAN and AUTO SEAT OPEN buttons during cleaning and maintenance Otherwise the sensor m
44. ly close the water shutoff valve and contact our company for instructions on resolving any of the above issues Never use any defective devices as this may result in electric shock or fire Low temperature burns A low temperature burn may occur when the skin has been in contact for some time with an object at relatively low temperature about 104 F 40 C Susceptibility to burns also depends on an individual s skin sensitivity and other factors In order to protect against the possibility of a low temperature burn the toilet seat temperature should be set to Low or OFF Especially in case of the use for a long period of time set the seat temperature should be set to OFF As low temperature burns can also occur when the user skin is contact with heated air the dryer temperature should also be set to Low These precautions should especially be observed when any of the following use the toilet Children Elderly persons Persons with illnesses Persons with limited mobility Persons with sensitive skin Persons on medication that may cause drowsiness Persons who are under the influence of alcohol Persons who are suffering from exhaustion If the toilet seat is used for a long period of time without setting the seat temperature to OFF the user may suffer a low temperature burn If the dryer is used for a long period of time on a setting higher than Low the user may suffer a low
45. m the water shutoff valve 10 Disconnect the power plug from the outlet When water may freeze e Use a container or pump to remove the water in the toilet bowl and pour antifreeze into the bowl If water is simply removed sewer gas will be emitted from the drain pipe e When using the toilet again Be sure to perform usage checks before use Page 14 54 Preventing Freezing To prevent damage that may result from freezing water follow the procedures described below When performing these procedures the power save feature should be turned off General Anti freeze Measures 1 Set the seat temperature to high and close the seat lid 2 Turn off the power save function Page 26 3 Heat the toilet room If the toilet room cannot be warmed perform the o following antifreeze procedures The automatic antifreeze function includes an automatic drain method and an intermittent flushing method Select either method according to the antifreeze method of the toilet Antifreeze method of the toilet Automatic drain method Drains water whenever a user leaves the toilet seat Intermittent flushing method Flushes the toilet periodically Automatic Drain Method Water is drained whenever a user leaves the toilet seat to prevent water from freezing 1 Press the Power save A and Auto Clean buttons B simultaneously for 2 seconds Water is drained for 15 seconds imm
46. mote control backlight will be illuminated when in use a Transmitter b Toilet seat OPEN CLOSE button c STOP button d Rear cleansing button e Rear cleansing mild button f Front cleansing button g Water pressure adjustment button h Flush buttons Full Partial i Power button j Massage button k Deodorizer button I Dryer button m Transmitter n NOZZLE POSITION adjustment button Note e When the remote control is removed from the holder buttons on the operation panel cannot be used except the STOP button Be sure to use the remote control while set in the holder e Do not operate the remote control with wet hands Failure to observe this may cause failure Reference e When operating the sub operation panel make sure the transmitter is facing the upper body sensor on the indicator The operation may not be accepted due to failure of signal transmission AT200 Features Remote Control Unit 2 Secondary Panel a Hr Min buttons b Power save button o ov c Seat temperature button a d Water temperature button e Auto flush button f Nozzle cleaning button g Battery LED h Night light button i Auto seat open button j Dryer temperature button 3 Secondary Panel LCD n k Auto flush I Auto seat open WATER TEMP SEAT m Time goii PT il SEI b n Water temperature indicator d
47. n is set to its lowest level Water does not The seat sensor does not Senden eear spray out detect a user Your clothes mean that detection by the seat sensor is difficult Allow the sensor to detect your skin This is not a problem Priority is given to flushing Press the The toilet is being flushed button for rear cleansing or front cleansing again after the toilet has been flushed This is not a problem When water temperature is extremely low in winter etc it may take longer than usual until water is sprayed due to preparation for spraying warm water Press the Water temp button The water temperature is set at and adjust the temperature to Water is not warm It takes longer The temperature of the water than usual until supplied to the seat unit is too water sprays out low its lowest setting the appropriate level This is not a problem When The temperature of the water water supplied to the seat unit is too temperature is low in winter low for example the water pressure may become slightly weaker This is not a problem Priority is given to flushing Press the The toilet is being flushed button for rear cleansing or front cleansing again after the toilet has been flushed The water pressure is too low The cleaning brush or other The nozzle guard tools touched the guard during Attach the nozzle guard is unstable cleaning and the guard has correctly fallen off
48. n the Spray Strength button C The water pressure can be adjusted to any of six levels Select the water pressure as desired To change the cleansing mode Press the Cleansing button B a second time during rear cleansing mild Pressing Cleansing during rear cleansing mild alters the mode Once the cleansing is stopped the cleansing mode starts with rear cleansing mild when Cleansing B is pressed C Rear cleansing mild 1 Oscillating spray gt Oscillating spray narrow The nozzle moves back and forth to wash a wide range The nozzle moves back and forth over a short span for more thor ough cleansing Rear cleansing rear cleansing mild Equipped with an auto stop function which terminates cleansing after 2 minutes However when the massage function or oscillating spray is activated while the rear cleansing or rear cleansing mild function is performed the cleansing time will be lengthened by 2 minutes This will automatically stop after the cleansing has been performed for up to 6 minutes in total Self cleaning nozzle This function is provided to automatically clean the nozzle before and after the rear cleansing or rear cleansing mild function is performed Water comes out from a point near the nozzles When sitting on the toilet seat or pressing any button for the shower water comes out from a point near the
49. nated power plug again Disconnect the power plug A short circuit has occurred from the outlet and request repairs Disconnect the power plug from the outlet and request repairs The toilet seat lid is not attached Attach the toilet seat lid Cin closed position A voltage other than 120 V is applied The batteries are dead low Replace the battery with a new battery indicator flashes one The batteries are not inserted Insert the battery in the correct The remote correctly direction control unit does The remote control s not operate The _ transmitter receiver is dirty or Remove dirt or water POWER LED is wet onan a An fluorescent light with Turn off the light and check the inverter ballast is used operation The receiver of the remote control is exposed to direct Avoid direct sunlight sunlight The remote control unit is Press the Power button to turn turned off on the remote control When the remote control is installed on the wall opposite the receiver the remote control may stop functioning before the battery indicator starts flashing Troubleshooting Rear Cleansing Rear Cleansing Mild and Front Cleansing The water shutoff valve is Turn the open close handle closed counterclockwise 90 The filter is clogged Clean the filter a The water supply pressure is too low or the water pressure Press on the Spray Strength setting on the remote control butto
50. nclusive of the chinaware and all mechanical parts confirms that it is defective in materials or workmanship DXV by American Standard will repair or at its option exchange the product for the same or a similar model This limited warranty applies only to the original non commercial purchaser and installation of the products In the event of a limited warranty claim proof of purchase will be required save sales receipts For this warranty to become effective the warranty registration process must be completed via the internet or telephone per the warranty registration instructions This limited warranty does not apply to commercial installations The warranty for commercial installations is two years on the toilet This warranty does not apply to local building code compliance Since local building codes vary considerably the purchaser of the product should check with a local building or plumbing contractor to ensure local code compliance before installation This warranty will be void if the product has been moved from its initial place of installation if it has been subjected to faulty maintenance abuse misuse accident or other damage if it was not installed in accordance with DXV by American Standard s instructions or if it has been modified in a manner inconsistent with the product as shipped by DXV by American Standard The warranty will be void if the product has failed as a result of worn out of consumable parts such as packing
51. nfectants as the gas vapor could damage this product or cause failures Do not use hot water as this may damage the toilet Do not use an abrasive brush or cleanser as these will deteriorate the effect of the Hyper Clean surface Contamination at the bottom of the bowl A shadow in the bottom of the toilet bowl might make the bottom of the toilet appear dirty when the night light is lit Cleaning the Nozzle Guard e Clean the nozzle guard with a dampened soft cloth or sponge As mentioned previously use a mild liquid all purpose cleanser Note e Avoid wiping with a dry cloth or toilet paper as this cause scratches e Avoid using an abrasive brush or cleanser The nozzle guard can be removed for easy cleaning See the procedure below Removing the Nozzle Guard 1 Turn off the Auto Clean and Auto Seat Open buttons This will disable the automatic lid and automatic flush functions 2 Lift the seat lid and seat 3 Press the Nozzle Cleaning button A When the nozzle protrudes press the STOP g button B to stop the motion The shower nozzle protrudes and pushes up the nozzle guard A 4 Lift the nozzle guard with both hands pull it upward and remove it as shown in the diagram eZ 5 Press the STOP button to return the nozzle to its original position p 6 Clean the removed nozzle guard KAN TA 44 Cleaning the Nozzle Guard
52. ng the power needs to be kept on Refer to Preventing Freezing Page 55 Suitable cleansers Use a neutral cleanser or one suitable for plastics to clean the toilet seat and lid Do not use chlorinated cleansers acidic cleansers or disinfectants on ceramic parts Odors upon flushing If there is insufficient ventilation in the room for example when a large kitchen range hood is used odor may be experienced temporarily when flushing the toilet Ventilate the toilet room adequately 36 Manual Toilet Flushing In the event that water service to the toilet is interrupted fill a bucket with water and carefully pour the contents into the toilet bowl to manually flush the toilet Repeat if necessary When the waste is cleared from the bowl pour water into the bowl to restore the bowl s water level to its normal height Note Be very careful not to spill water onto the floor when carrying water in a bucket or pouring it into the toilet Do not allow water to splash on the outlet Cleaning and Maintenance Below our company offers some general guidelines as to the cleaning of this product Please note that there are some cleaning products which should not be used As a general rule our company recommends the use of liquid all purpose cleansers for this product Cleaning tools tem Description Location Use old towels T shirts etc cut to an Toilet seat lid Soft c
53. o Seat Open button A to activate this feature CN AUTO SEAT OPEN button appears D EA on the LCD The function is set to ON in the default settings Ly If the seat sensor is not activated after the seat lid opens independently the seat lid automatically closes after approximately one minute The upper body sensor detects the motion of a person and automatically opens the toilet seat lid e To open the toilet seat lid and toilet seat simultaneously Press the STOP and Open Close buttons simultaneously for 2 seconds A short beep sounds when the setting is complete The seat and seat lid close approximately 1 minute after the user leaves the toilet Press the STOP and Open Close buttons simultaneously for 2 seconds to reset A beep sounds when the setting is complete To manually open and close the toilet seat lid or seat Press the Auto Seat Open button to deactivate this feature The AUTO SEAT OPEN display on the LCD disappears When a small child uses the toilet turn off the auto seat open function The seat sensor may not be able to detect a small child s body and although rare the toilet seat lid may start to close during use The toilet lid will not open for 10 seconds after it is closed manually To open and close the toilet seat with the remote control 1 Press the Open Close button B to open the toilet seat 2 Press the Open Close button B again to c
54. r D buttons simultaneously for 2 seconds A short beep sounds when the setting is complete 33 Comfort Features Restoring the Default Settings All of the product s functions can be reset to their factory defaults even after the settings have been changed by the user To restore the factory default settings follow the steps below Press the Water temp button A and Seat temp B buttons simultaneously for 2 seconds A short beep sounds when the setting is complete e The factory default settings are summarized in the table below Functions Default setting Automatic deodorizing Z Deodorizer mode Automatic switch between turbo mode and normal mode Power save Seat heater auto off Inactive Levels 2 M Water pressure a Dryer temperature Auto flush Flush delay setting 6 seconds Night light illumination Bowl base and bowl inside O zZ O 7 T T Signal reception sound 7a Antifreeze Automatically opens and closes only the toilet seat lid Auto seat open hroms on Storing the Settings The product s user defined settings are maintained even when the power button is turned off or the power plug is disconnected from the outlet However the one touch power save function is reset when the power plug is discon nected Page 26 Other References Other References The seat sensor prevents unintended operation This toilet is equipped with a seat sen
55. rcumstances other than the above or if the water does not stop close the water shutoff valve and disconnect the power plug from the wall outlet Contact our company for repair instructions Warm air smells when the toilet is initially used When the toilet is new it may smell a little particularly when warm air is used However this is not a malfunction and will disappear after a short time Other References Interference with radio or television If a radio or a TV is placed near this toilet interference with the signals from remote control unit may occur If the interference occurs move the radio or TV away from this product Condensation forms Due to humidity and or temperature differences between room and the seat unit or surface of the bowl condensation may form on the seat unit or bowl Ventilate the toilet room adequately to prevent condensation If condensation forms wipe it off with a dry cloth Condensation may stain or damage the floor This toilet is designed to prevent condensation from forming However ambient conditions may still cause condensation to form Energy saving tips Close the toilet seat lid after use Lower the seat and water temperature Adjust the seat and water temperature according to the season Use the power save functions Unplug this product when you are gone for long periods of time If there is any possibility of water freezi
56. red after 8 hours Set temperature power save mode Temperature in a lt 83 hours gt OFF D B D Q E D 2 i o n Once 8 hours have passed and the heating function restarts the seat unit goes into standby X Indicator When in standby mode the power save LED changes from lit to single flashing Upper body sensor Reference e The one touch power save function is reset after a power failure or when the power plug is disconnected avec POWER Press the Power save button A The power save LED on the indicator lights up A short beep sounds when the setting is complete To cancel the one touch power save function Press the Power save button A The LED on the indicator goes out A beep sounds when the setting is complete Power Save Function Advanced Power Save always on The advanced power save function reduces power con l sumption by lowering the water and seat temperatures 5 X a a when the toilet seat lid is closed E set imoa v F F Pare SiT ture i Power is saved at all times while the toilet seat lid is la ak closed m When the seat lid is open the power save mode is a OFF temporarily cancelled When the advances power save function is activated the power save LED on the seat unit flashes twice rapidly When the advanced power save function i
57. ressure can be adjusted to any of six levels Select the water pressure as desired To change the cleansing mode Press the Cleansing button B a second time during rear cleansing Pressing Cleansing during rear cleansing alters the mode Once the cleansing is stopped the cleansing mode starts with rear cleansing when Cleansing B is pressed Rear cleansing gt Oscillating spray gt Oscillating spray narrow The nozzle moves back and The nozzle moves back and forth over a forth to wash a wide range short span for more thorough cleansing Note Reference e When the water temperature is extremely low in winter e The water pressure may be further lowered for for instance the water pressure may become weak those who feel the water pressure is too strong e Sit further back on the toilet seat even at the lowest setting Page 31 If you sit further back on the seat there will be less water splashing e The rear cleansing or rear cleansing mild function stops when the toilet is flushed This function can not be started while flushing the toilet General Operation For rear cleansing mild e Press the Cleansing button B Water will drip from the nozzle This washes the nozzle before use The nozzle extends and water sprays e Press the STOP button A The spray will stop and the nozzle will retract To adjust the water pressure Press or o
58. rizing method Chemical absorption by deodorizer cartridge Deodorizing Power deodorizing 3 9 CFM 0 11 m min function Deodorizing capacity Full power deodorizing 4 9 CFM 0 14 m min Turbo deodorizing 6 0 CFM 0 17 m min 2 Dimensions 9 2 238mm W x 1 8 29 mm D x 1 4 45 mm H g Standard o remote 2 control Power Source 2 AAA alkaline batteries a Optional Parts Replacement Parts The nozzle tips should be replaced if they can no longer be cleaned Page 49 Repair Part No 7381438 201 O070A 7381439 201 O070A 7381440 201 O0070A 7381441 201 OO70A 7381442 201 O070A 7381443 201 0070 7381443 202 0070A 7381443 203 O0070A 7381443 204 0070A 7381443 205 0070A 7381443 206 0070A 7381444 201 O070A 7381445 201 O070A Description Pressurized pump Nozzle tip for shower Nozzle tip for bidet Preventing condensation cover for stop valve Spare nozzle shutter Water supply hose 200mm Water supply hose 400mm Water supply hose 580mm Water supply hose 680mm Water supply hose 900mm Water supply hose 1000mm Remote control Deodorizer Cartridge For additional components or to order replacement parts contact your local customer service repre sentative or see the website at www DXV com DXV AMERICAN STANDARD LIMITED WARRANTY This toilet comes with a three year warranty on all parts of the toilet If inspection of this DXV by American Standard plumbing product i
59. s activated along with the one touch power save function the power save LED remains lit while one touch power save mode 8 hours is activated and flashes twice rapidly while it is in standby mode 16 hours Indicator Upper body sensor 1 Press the Power save B and Nozzle Cleaning C buttons simultaneously for 2 seconds The power save LED on the indicator flashes A short beep sounds when the setting is complete To cancel the advanced power save function Press the Power save B and Nozzle Cleaning C buttons simultaneously for 2 seconds The LED on the indicator goes out A beep sounds when the setting is complete B Reference e When the power save function is activated the toilet seat temperature is lowered and may feel cold In this case the power save function can be cancelled e Even when the power save function is turned off leaving the toilet seat lid closed is an effective way of saving power Deodorizing Function Press the Deodorizer button on the remote control to enhance the deodorizing feature 1 Press the Deodorizer button A while the automatic deodorizing function is operating A short beep sounds when the setting is complete The deodorizer fan goes into turbo mode which boosts the effect of removing odor in the toilet bowl 2 Press the Deodorizer button A again to stop it A beep sounds when the setting i
60. s before attaching the filter as failure to do so could result in water leakage and flooding Low Battery Indicator The battery indicator on the main display panel will flash when the battery needs replacement Page 34 Replace the batteries with new ones as described in the following procedure Note e Install batteries with the positive and negative poles in the correct direction as shown on the remote control case e Do not use new and old batteries together O e Use alkaline batteries only Replacing the Remote Control Batteries 1 Lift the remote control and remove it from its holder 2 Remove the back cover and replace the batteries with new ones two 1 5 V AAA alkaline batteries Use a tool such as a flat screwdriver to release the lock when the back cover cannot be removed easily 3 Press the Hr and Min buttons to adjust the time Page 16 4 Attach the back cover and slide the remote control into its holder from the top Reference e The battery mark flashes only when the battery has expired The battery mark is not normally displayed The initial batteries were used for operation checks when the remote control was installed so their service life may be shorter than commercially available batteries e Depending on the size of the room finishing and color particularly a dark color of the wall the remote control may stop functioning before the
61. s complete The deodorizing mode returns to normal automatic mode The deodorizer fan automatically stops 1 minute after the user stands up To change the default deodorizing setting to turbo mode Press the Deodorizer B and Power __ 1B SS save C buttons simultaneously for 2 seconds A short beep sounds when the setting is complete S The automatic deodorizer always operates in the turbo mode To reset press the Deodorizer and Power save buttons simultaneously again for 2 seconds C A beep sounds when the setting is complete Night Light Function When the seat lid opens a soft light illuminates the base of the toilet and the inside of the bowl When the user leaves the toilet the light goes out automatically The default setting for this light is ON 1 Press the Light button A to deactivate the night light A beep sounds when the setting is complete 2 Press the Light button A again to turn on the night light A short beep sounds when the setting is complete F Reference AJ e While the night light is lit shadows in the bottom of the toilet bowl might make the toilet look as if it is dirty In this case refer to To deactivate the night light in the bowl below To deactivate the night light in the bowl Press the Seat temp B button and Auto Clean C buttons button simultaneously for 2 seconds A short beep sounds when the
62. sor that will only allow the cleansing and frying functions to operate when the toilet seat is occupied The rear cleansing rear cleansing mild front cleansing and dryer features do not operate even if the button is pressed unless the toilet seat is occupied Since the seat sensor uses light reflection it may not be able to detect a user Such cases are listed below along with solutions If the user leans forward or sits on the front of the seat Sit further back on the seat If the user wears dark clothes that do not reflect light easily Place a hand over the sensor so that the sensor can detect the user If the sensor is dirty or wet Clear the sensor with a soft cloth A low battery indicator is provided The battery indicator on the remote control flashes with the display on the diagram on the right when the battery charge becomes low When the display indicating low battery charge appears replace the batteries in the remote control as soon as possible Page 53 Such factors as the size of the room decor and color particularly a dark color may weaken the signal causing the remote control to stop functioning before the indicator starts flashing If a button on the remote control is pressed with the toilet room door open or with the battery indicator flash ing the signal may not reach the seat unit and the specified function may not be activated The toilet seat and seat lid close slowly To prevent
63. tart to close when the toilet is in use Save These Safety Precautions Safety Precautions AN GROUNDING INSTRUCTIONS The product is for use on a 120 V circuit and has a grounding plug that looks like the plug illustrated in sketch A in Figure 1 A temporary adapter which looks like the adapter illustrated in sketches B and C may be used to connect this plug to a 2 pole receptacle as shown in sketch B if a properly grounded outlet is not available The temporary adapter should be used only until a properly grounded outlet Figure 1 can be installed by a qualified electrician The green colored rigid ear lug and the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover Whenever the adapter is used it must be held in place by the screw If it is necessary to use an extension cord use only a three wire extension cord that has a three blade grounding plug and a three slot receptacle that will accept the plug on the product Replace or repair a damaged cord If there is no electrical outlet in the bathroom consult a licensed electrician for the installation of a GFClprotected outlet The product should be grounded In the event of an electrical short circuit grounding reduces the risk of electric shock by providing an escape wire for the electric current This product is equipped with a cord having a grounding wire with a grounding plug The plug
64. the risk of electrocution Improper use of the grounding plug can result in a risk of electric shock Do not place or store product where it can fall or be pulled into a tub or sink When installing either the toilet or the remote control avoid splashing water directly onto these items In addition this product should not be installed in a humid atmosphere e g inside a shower room Do not pour drop into the water or detergent inside outside the power plug of the product or remote control Do not reach for a product that has fallen into water Unplug immediately Do not use while bathing AN WARNING To reduce the risk of burns electrocution fire or injury to persons Use this product only for its intended use as described in this manual Do not use attachments not recommended by the manufacturer Do not connect or disconnect the power plug with wet hands as this may cause electric shock Do not splash water or liquid cleaners directly onto the seat unit or power plug as this may cause electric shock or fire This product should only be connected to a 120 VAC 60 Hz GFCl protected outlet E Do not connect too many power cords to a single electrical outlet as this may result in fire Hold the power plug when connecting or disconnecting it If the plug is connected or disconnected by holding the cord the plug or cord may be damaged resulting in electric shock or fire OOO
65. turned off deodorizing function Auto Flush Function a The toilet does not flush The Auto Clean buttoniis Turn on the Auto Clean button f turned off automatically Water flow is The water shutoff valve is not Open the water shutoff valve oOo weak or the toilet fully open fully is not flushed completely The filter is clogged Clean the filter The toilet flushes Intermittent flushing function Turn off the intermittent flushing by itself may be operating function Troubleshooting Auto Seat Open Function Press the Open Close button If the seat does not open or close automatically disconnect the power plug from the outlet and contact our company for service The Auto Seat Open button is Turn on the Auto Seat Open 17 turned off button The commercial toilet lid cover and or seat cover is too heavy or is caught somewhere The seat and lid closes too quickly The seat and lid are pushed during auto close Remove the toilet seat lid cover and or seat cover Assemble the toilet seat lid correctly The toilet seat lid is not The lid does not assembled correctly open or close The toilet seat lid does not open automatically automatically for approximately 10 seconds after it is closed manually or with the remote control The toilet seat lid was closed manually or with the remote control The upper body sensor is blocked or dirty Clean the s
66. ure is low the p is cy at water sprayed from r e TN the nozzle may not ii reach the user at the lowest setting 4 To return to the default setting E Press the Nozzle Cleaning E and i N gt Min F buttons simultaneously TER again for 2 seconds A short beep sounds when the setting is complete Comfort Features Adjusting the Auto Flush Function The automatic flush function is factory set so that the flush cycle will begin 6 seconds after the user stands up from the toilet However this flush delay setting can be changed To adjust the flush delay setting follow the steps below Press the Power save A and Hr B buttons simultaneously for 2 seconds A short beep sounds when the setting is complete Pressing the buttons changes the flush delay time See the diagram below for the different flush delay settings Default setting 7 6 seconds gt 10 seconds gt 15 seconds 2 seconds A beep sounds when the setting is returned to the default Muting the Signal Reception Sound The remote control will emit a signal reception sound whenever a button is pressed The factory default setting for this feature is ON To cancel the signal reception sound follow the steps below Press the Seat temp C and Deodorizer lt D buttons simultaneously for 2 seconds van To return to the default setting Press the Seat temp C and Deodorize
67. use damage Do not place a heater near the seat unit as this may cause discoloration of the plastic or failure of the cleansing and drying functions Do not use any paper other than toilet paper Be careful not to drop any foreign substances in the bowl as they may clog the drain pipe N7 If the toilet becomes clogged use a plunger to clear the blockage Do not flush the toilet until this has been cleared as this may cause flooding Do not wipe the toilet s body seat lid or other plastic parts with a dry cloth or toilet paper Refer to page 38 for details of cleaning The surface of plastic parts may become scratched and lose their gloss Preparation and Checks Before Use Before using the seat unit for the first time check the following items 2 1 1 Checking the Water Shutoff Valve 1 If the water shutoff valve is closed turn the open close handle counterclockwise 90 degrees to fully open it 2 Connecting the Power Plug to the Outlet 2 e First connect the power plug to the outlet 120 VAC alg e Then check that the power LED is lit Wl Indicator Upper body sensor The power LED on the indicator lights green If the power LED does not light the main power may have been turned off If OFF is displayed on the LCD press Power button on the remote control Note e Please wait for about 10 seconds before connecting the power plug again

user manual engliSh

Contents

Download Pdf Manuals

Related Search

Related Contents