SYNTHESIS S5160/230 POWER AMPLIFIER USER`S MANUAL
Contents
1. SYNTHESIS SJ160 230 POWER AMPLIFIER USER S MANUAL TABLE OF CONTENTS SECTION 1 0 Precautions 1 1 Important Safeguards for Audio Products 2 0 Introduction and Features of the 55160 3 0 Operation and Controls 3 1 55160 4 0 Connecting Your Synthesis System 4 1 JBL Synthesis One Suggested Rack Mounting Order 4 2 JBL Synthesis One Control Wiring Diagram 43 JBL Synthesis One Interconnection Diagram 5 0 Installing the 55160 6 0 Troubleshooting 7 0 Specifications 8 0 Synthesis Limited Warranty JBL Synthesis S5160 230 Power Amplifier User s Manual 2005 JBL JBL and Synthesis are registered trademarks of JBL Incorporated All Rights Reserved JBL Synthesis 8500 Balboa Boulevard Northridge CA 91329 250 Crossways Park Drive Woodbury NY 11797 516 255 4JBL 2 Route de Tours 72500 Chateau du Loir France Printed on Recycled Paper Part Number S5160 2300M H A Harman International Company 1 0 PRECAUTIONS 1 1 Important Safeguards For Audio Products PLEASE READ CAREFULLY ALL THE FOLLOWING IMPORTANT SAFEGUARDS THAT ARE APPLICABLE TO YOUR EQUIPMENT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To reduce the risk of electric shock do not remove cover or back No user serviceable parts inside Refer servicing to qualified service personnel CAUTION To prevent electric shock do not use this polarized plug with an extension cord receptacle or other outlet unless the2. Denne m rkat p komponenten advarer om vigtig driftsog vedligeholdsinformation i den tilh rende litteratur Norsk Viktig informasjon om sikkerhet Ta vare p denne veiledningen for senere bruk F lg alle anvisningene og advarslene som er angitt p apparatet Apparatet skal alltid anvendes med korrekt spenning Produktbeskrivelsen inneholder spesifikasjoner for stramkraav V r oppmerksom p at det ved ulike driftsspenninger kan v re n dvendig bruke en annen led ningog eller st pseltype Apparatet skai ikke monteres i skap uten ventilasjon eller direkte over varmepro duserende utstyr som for eksempel kraftforsterkere Den maksimale romtempera turen som st r oppgitt i produktbeskrivelsen skal overholdes Apparatet er utstyrt med ventilasjons pninger For at apparatet skal v re p litelig i bruk og ikke overopphetes m disse pningene ikke blikkeres eller tildekkes Stikk aldri noe inn i ventilasjons pningene og pass p at det aldri sales noen form for v ske p apparatet Dette apparatet er utstyrt med et jordet st psel Dette er en sikkerhetsforanstalt ning som ikke m forandres Utgangsplugger fra audioforsterkere skai aldri koples direkte til apparatet Unng brannfare og elektrisk stat ved s rge for at apparatet ikke utsettes for regn eller fuktighet og ikke anvendes i n heten an vann Apparatet skal ikke brukes hvis det har blitt utsatt for st t er skadet eller blitt v tt eller hvis endringe
3. attached to the unit This will ensure that there is sufficient air space underneath so that heat can be dissipated effec tively 2 Make sure that the amplifiers are located in a well venti lated cool area Be certain that the front and rear panels are not obstructed as the cooling fan brings air in from the front and expels it at the rear It is very important not to obstruct the airflow from the center front panel heat buildup and premature failure may occur 6 0 TROUBLESHOOTING Problem Amplifier does not turn on Neither the red nor blue indicator lights are on Make sure that the amplifier is plugged in and verity that there is the proper voltage 230V at the wall outlet Problem The red indicator lights but the blue indicators do not light up when the power switch is depressed 1 If the amplifier is being used in a Synthesis system make sure that the surround processor Is turned on the Auto On Manual On switch is in the Auto On position and that all of the neces sary DIN cables are connected between the various system components Refer to the CONNECTING YOUR SYNTHESIS SYSTEM section for reference 2 If the amplifier is not being used with a Synthesis system make sure that the Auto On Manual On switch 5 in the Manual On position Problem There is no sound from the speakers but the amplifi er is on blue indicators lit 1 Make sure that the surround processor or equalizer is on and that the co
4. l kytke audiotehovahvistimen l ht j suoraan mihink n yksik n liit timeen S hk iskun ja palovaaran v ltt miseksi yksikk ei saa olla sateessa tai kosteassa eik sit saa k ytt m r ss ymp rist ssa l k yt yksikk jos se on pudonnut vaurioitunut kostunut tai jos sen suorituskkyky on huomattavasti muuttunut maik vaatii huoltoa Yksik n saa avata vain laitteeseen perehtynyt huoltohenkil Kansien poisto altistaa sinut vaarallisille j nnittelille T m kolmio joka esiintyy homponentissasi varoittaa siua erist m tt m n vaarallisen j nnitteen esiintymisest yksik n sis ll T m j nnite saattaa olla riitt v korkea aiheuttamaan s hk iskuvaaran T m koimio joka esiintyy komponentissasi kertoo sin ulle ett t ss tuotedokumentoinnissa esiintyy t rkeit k ytt ja yll pite ohjeita Svenska Viktiga s kerhetsf reskrifter Spara dess f reskrifter f r framtida bruk F lj alla anvisningar och varningar som anges p engeten Anv nd alltid r tt n tsp nning Se tillverkarens bruksanvisningar f r informa tion om effektkrav M rkv l att andra matningssp nningar eventuellt kr ver att en annan typs n tsladd och eller kontakt an nds Installera inte enheten i ett oventilerat stativ eller direkt ovanf r utrustningar som avger v rme t ex effektf rst rkare Se till att omgivningens temperatur vid drift inte verskrider det angivna v rdet i produktspeci
5. masked by the program being listened to Comprehensive and Isolated Circuit Protection The S5160 amplifier employs a sophisticated protective circuit one for each channel that senses many possible fault conditions such as shorted loudspeaker wires or excess INTRODUCTION ANDFEATURES power demand and turns the affected channel s and their blue front panel indicators off until the fault condition is removed at which time normal operation is automatically restored While protection of this sort is not uncommon in today s well designed amplifiers a remarkable feature of the Synthesis 551605 protective circuits is that they are optically coupled to the signal circuit there is no direct electrical connection between the signal path and the pro tective circuitry As a result there can be no coloration of the music no interaction between protection and amplification until certain thresholds are exceeded at which point the channel s turn off completely 3 0 OPERATION AND CON TROLS OPERATION CONTROLS 3 1 55160 1 Power Switch Pushing this button is all that is required to turn on the 55160 if it is not part of a Synthesis system and the Manual On Auto On switch rear panel is in the Manual On position If the amplifier is used as part of a JBL Synthesis System and the Manual On Auto On switch is in the Auto On position the amplifier will tum on when the surround processor Is activated The front pane
6. push objects of any kind into this product 25 The product should be mounted to a wall or ceiling through openings as they may touch dangerous voltage only as recommended by the manufacturer points or short out parts that could result in a fire or elec tric shock Never spill liquid of any kind on the product Note to CATV system installer 21 The apparatus shall not be exposed to dripping or This reminder is provided to call the CATV system splashing and no objects filled with liquids such as vases installer s attention to Article 820 22 of the NEC that pro shall be placed on the apparatus vides guidelines for proper grounding and in particular 22 Do not attempt to service this product yourself as specifies that the cable ground shall be connected to the opening or removing covers may expose you to danger grounding system of the building as close to the point of ous voltage or other hazards Refer all servicing to qualified cable entry as practical service personnel Figure 1 Example of Antenna Grounding as per National Electrical Code ANSI NFPA 70 Antenna Lead In Wire Ground Clamp Anienna Discharge Unit NEC Section 810 20 Grounding Conductors NEC Section 810 21 Electric Service Equipment Ground Clamps Power Service Grounding Electrode System NEC Art 250 Part H Part No HCGUL1492 6500 04 2004 EN Deutsch Wichtige Sicherheitsanweisungen Heben Sie sich diese Sicherheit
7. running ground wires between the rear panel screws of the amplifiers and the other system components such as the surround processor or signal processing package If you still encounter difficulty after trying the above suggestions call your JBL Authorized Dealer or visit our website at www jbl com for further assistance 7 0 SPECIFICATIONS Rated Power Output SPECIFICATIONS 160W per channel into 8 ohms all channels driven THD 0 03 20Hz 20kHz Input Impedance 28k ohms Sensitivity 1V in 28 28V out THX Level 1 25V in 150 watts out Frequency Response at 1 W 20Hz 20kHz 0 02505 S N Ratio A weighted at rated power 1000B Damping Factor 8 ohms 400 Dynamic Headroom 5Hz 100kHz 0 3dB IM Distortion 0 03 Unit Size 178 mm H x 484 mm W x 495 mm D 7 H x 19 W x 19 D Unit Weight 44 kg 97 lbs Shipping Weight 50 kg 117 Ibs All features and specifications are subject to change without notice THX is a trademark of THX Ltd JBL Synthesis 8500 Balboa Boulevard Northridge CA 91329 250 Crossways Park Drive Woodbury NY 11797 800 336 4JBL Chateau du Loir France Part No S5160 230 OM Printed in USA on recycled paper
8. 0 SE 000000000009009 a 2 32 90909090909090 82 He 009900000000063 a s fil 9090909096 p 9388 2020202020209 ii 090900000000095 E iii 000900000000095 a ig His 000000009000033 ig His OS080208080808 8 ag 05050505050505 E gs 0009000909690 5r i a 33 9505059595950 11 33 0505959595952 a 2 6 02020209020209 FFF 0202020290202091 8 a 85909595959080 78 5 a ES 808085808080 a 99909090969696 2 S080909080808o L H z 90909090909090 6 i 00900000808090 3 s gf 00000000000000 I B of 090000000590001 i e E H E E EEE gt EEE 5 5 0 PHYSICAL INSTALLING YOUR CONSIDERATIONS POWER AMPLIFIER Installation of the S5160 is a straightforward process IMPORTANT Amplifier must be installed following the directions described below to insure adequate performance and safety never install the amplifier with less free spacing around the A amplifier than the specified 1 The Synthesis S5160 power amplifier has been designed to be mounted in EIA standard racks or stacked freesianding as long as there are four inches 10cm of free spacing around the amplifier Top sides and rear If the S5160 is being mounted in a rack it is suggested that its feet be removed prior to installation If the S5160 will be stacked with other components use the feet that came
9. 0 09090909090909 i 09000000090000 6 2696969696962 0909090909090 20909090909090 8100000000000009 0909090909090 90909090909090 00000909090901 20202020909090 09090909090909 0595959520 09080809000 0000000000000 80209090909090 0908000909000 9595959595950 H 20902090909090 O 0505050505050 6202096262090 a 0009090009000 00000000000000 length 6880090909090909 209090909090904 20909090809090 000009009090 RCARGN 20 M Cone on Conn on Ss Power Awelden Ss rower Awelden Cables Included in 25001 7 101 ph GAl wAnlng HA Asoomar uAkmorn sAm chp SA wAnlng HA Asoomar uAkmorn seda renkon eriaimer 800 230 erialmer 800 230 a F1 Ajo e TAL I50VAC F TAL 250VAC Tant 350VAC O ce 2020202000200 ii B O0009090909 O 289898989598 9985 tE a BZ 3989030303080 H 0000090000009009 009080909090 0009090909090 5 308580202620 lO a 99690900060666 11 020909020902909 09090909090909 S HE 41 080909090968 090202902020909 1168 0009090290290909 O Hie 9090
10. 2 Input POWER AMPLIFIER 3 2626202696969 id i i i MOSSE senetan paa mupe reren sSt60230 Minimum Inpedance 0209090202090 28202090209090 202020202909090 82090902000209 229200000000 25 ch 3 Output OO R res ome Ch 2 Output OO turn off all Synthesis components before SDEC 2500A 230 nA Auto MODE MODE 5160 230 5160 230 exactly as indicated 1 To ensure proper operation connect the system control lines system is on 2 If any of the control lines become disconnected while the 9995995959990 0000900000000900 Caida ne wAsnb Aso s reconnecting control lines This will reset all operation 800 230 ng G Ae Amor Peach oles cokes Fa tGspe O o Pea 5 5 2625696969696 26 0802096269090 0009090909090 0696969696262 6262096262090 0809080209080 0505090505050 0202090262090 02090202909090 0808080802080 9596959549595 90 0202090962090 0809090209080 0808080969080 6269090962090 96969090909090 0209020909090 r O090909090909 29909090909090 09090909090909 0909090909090 0909090909090 0009090909090 0909090909090 0909090909090 20902090909090 O 22220292999999 28909090900099 2099999090999 y E 0909090909000 3239303030808 o o E 0909090909000 10 0202020259626 4 2808080808080 09990969090069 0009009090909
11. 9690909606 ag 0808026262090 5 90909090909000 00000000000000 HOJ Ho 00909000909098 REN O9090909090909 x EEEEBO 5050505050505 ger 2268050505050505052 080908090908 088 IDE 0800809080 MESE 090909090909094 HEEB 69596959690909 Ei D 2 08090009090909 i gt 2 29090909099909 ES 209090202902020 259626969696 26 85 90000000009090 HO 96969090909696 5 z 29089805080505 3 8 3 0090005000909 8 24 09090909090909 18 090290909090009 2 SE 00000000000000 2 00000090000000 SOS0S090909000 5090909090909 08090909090909 8696869696868 f 00090000090909 00090900090909 00008000005 80900090909090 lt 09090909020008 9 1 2090902090902054 22220909090909 tiid E z 22099990809090 O 2392999990999 PO 520009020202025 t Ok oy SN SS s 90000000000000 s 90909090908 8 69090909090909 68 0909090909090 0902090202090 0909090009090 SG6969696969696 00 2 0 0 0 c 4s 09090909000909 080909090900094 99909990990090 DB DB Bi 83959029099999 P El 23099090999909 e 20390039993099 i OE 20302090909099 5 059 o 5 O 262 O XE lt 0000000000000 8 5 xz 00000000000009 255 00000000000090 88 00000000000000 a 0002090000090 fH 0909090009090 S 5 fil 000009009000909 853 000009009090909 5 3531 0000000000000
12. amplifiers the power switches are in the depressed ON position and that the Auto On Manual On switches are in the Auto On position Operated in this mode all of the components will turn on with one touch of the power but ton on the surround processor s remote control CONNECTING YO 4 1 Synthesis One SYNTH YS Suggested Rack Mounting Order B S800 230 S5160 230 14 ea MN Oud cerda 5vde N TNA ZZ ada 50 0 00 oo QQ 3 e O O O Q O O Q A Q H SDP 40 3 lt D S Q D S Q 4 2 Synthesis One x O MALA Auro Aamo we POWelbOo s d erda GlOda N4 NOT 5vdc TO sPE Kes N3 N1 N5 P P P P P sheesh amita ta saco power Au Fler phage co Aufar A C 9096 saco power Au Fler e Hora sen he wah 800 230 OM ra ohm chs Input Input O ON Tron OJ a y if sP xBIN eis cha Input cha Input z H a arman internettonet company whi use POWER AMPLIFIER ch 2 Input ch
13. blades can be fully inserted to prevent blade exposure The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the iterature accompanying the appliance Read these instructions Keep these instructions Heed all warnings Follow all instructions use this apparatus near water Clean only with a dry cloth block any ventilation openings Install in accor the manufacturer s instructions Do not install near any heat sources such as radiators S m c gt ro B 5 heat registers stoves or other apparatus including ampli fiers that produce heat 9 Do not defeat the safety purpose of the polarized or walked on or pinched particularly at plugs specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the Servicing is required when the apparatus has been dam aged in any way such as power supply cord or plug is the product be sure the antenna or cable system is PRECAUTIONS grounding type plug A polarized plug has two blades
14. er of audio reproduction in over fifty years of preeminence in the field This amplifier has been designed and crafted to provide the user with a high level of sonic performance special attention has been paid to minimize the number of components in the audio signal path resulting in extremely low distortion excellent tran sient response and wide dynamic range Synthesis prod ucts set new benchmarks in audio technology and when used as part of a complete JBL Synthesis System will bring the ambience and acoustics of some of the world s greatest concert halls and theaters into your home To obtain the best performance trom this amplifier please be sure to completely read this user s manual and use the 65160 only in accordance with its instructions Features The JBL Synthesis S5160 power amplifier features the following THX Ultra Specifications This amplifier meets or exceeds the stringent specifications set by the THX Ltd Audio division in their specifications for Ultra class certification including power handling total harmonic distortion frequency response signal to noise ratio slew rate and crosstalk When incorporated into a complete THX system you wil hear in your home what the director and sound engineer heard in the recording studio Full Five Channel Operation The S5160 has been designed to integrate well into the world of multi channel audio It is designed to reproduce the front left and right center and
15. erta nicamente por personal calificado Si usted quita las coberturas se expondr a voltajes peligrosos Este tri ngulo que apaece en su componente le advierte sobre la existencia dentro del chasis de voltajes peligrosos sin ais lantes voltajes que son lo suficientemente grandes como para causar electrocuci n Este tri ngulo que aparece en su componente lo alerta sobre las instrucciones de operaci n y mantenimiento importantes que est n en los materiales de lectura que se incluyen Italiano Importanti norme di sicurezza Conservare le presenti norme per l utilizzo futuro Osservare tutte le istruzioni e le avvertenze apposte sull unita Utilizzare esclusivamente con la tensione di rete corretta Consultare le istruzioni operative fornite dal fabbricante per i dati riguardanti la tensione e l assorbimento di corrente Potrebbe essere necessario l uso di cavi di rete e o di spine diverse a seconda della tensione utilizzata Non installare l unit in uno scaffale privo di ventilazione oppure direttamente sopra una fonte di calore come ad esempio un amplificatore Non superare la temper atura ambientale massima di funzionamento riportata nei dati tecnici del prodotto Le fessure e le altre aperture nella scatola servono alla ventilazione Per un fun zionamento affidabile e per evitare un eventuale surriscaldamento queste aper ture non vanno ostruite o coperte in nessun modo Evitare in tutti i casi di inserire oggetti di q
16. fikationen Beh llaren r f rsedd med h l och ppningar f r ventilering F r att garantera tillf rlitlig funktion och f rhindra verhettning f r dessa oppningar inte block eras eller t ckas Inga f rem l f r skuffas in genom ventilationsh len Inga v tskor f r spillas p enheten Produkten r f rsedd med en jordad 3 tr dskontakt Detta en s kerhetsfunk tion som inte f r tas ur bruk Anslut aldrig audioeffektf rst rkarutg ngar direkt till n gon av enhetens kontakter F r att undvika elst t eller brandfara f r eenheten inte uts ttas f r reegn eller fukt eller anv ndas p st llen d r den blir v t Anv nd inte enheten om den far fallit i golbet skadats blivit v t eller om dess prestanda f r ndrats m rkbart vilket kr ver service Enheten f r ppnas endast av beh rig servicepersonal Farliga sp nningar blir tillg ngliga n r locken tas bort Denna triangel som visas p din komponent varnar dig om en oisolerad farlig sp nning inne i engeten Denna sp nning r eventuellt s h g att fara f r elst t f religger Denna triangel som visas p din komponent anger att viktiga bruksanvisningar och servideanvisningar ing r i dokumenta tionen i fr ga 2 0 INTRODUCTION AND FEATURES Introduction Congratulations on your purchase of this JBL Synthesis 65160 power amplifier You have purchased a product that embodies the best of what JBL has learned about the emotional pow
17. ilsittes den korrekte sp nding Der henvises til brugsanvis ningen der indeholder specifikationer for str mforsyning Der g res opm rk som p at ved varierende driftssp ndinger kan det blive n dvendigt at bruge andre lednings og eller stiktyper Apparated m ikke monteres i et kabinet uden ventilation eller lige over andet udstyr der udvikler varme f eks forst rkere Den maksimale omgivelsestemper atur ved drift der st r opf rt i specifikationerne skal overholdes Der er ventilations bninger i kainettet For at sikre apparatets drift og hindre overophidning m disse bninger ikke blokeres elle tild kkes Stik aldrig noget ind igennem ventilations bningerne og pas p aldrig at spilde nogen form for v ske p apparatet Dette apparat er forsynet med et stik med jordforbindelse Denne sikkerheds foranstaltning m aldrig omg s Udgangsstik fra audioforst rkere m aldrig s ttes direkte i apparartet Apparatet m ikke uds ttes for regn eller fugt og m ikke bruges i n rheden af vand for at undg risiko for elektrisk st d og brand Apparatet m aldrig bruges hvis det er blevet st dt beskadiget eller vadt eller hvis ndringer i ydelsen typer p at det tr nger til eftersyn Fette apparat m kun bnes af fagfolk Hvis d kslet tages af uds ttes man for livsfarlig hajspending Denne m rkat p komponenten advarer om uisoleret farlig sp nding i apparatet h j nok til at give elektrisk st d
18. ing other than the mode switching function of Synthesis speakers as this may dam age the S5160 and will void the warranty 10 AC Inlet Your S5160 is shipped with an IEC type removable power cord that mates with the AC inlet on the rear panel To ensure proper operation use the supplied power cord This amplifier is NOT a multi voltage unit using a power cord that is not compatible with a 290V 50Hz AC wall receptacle will void the warranty 4 0 INTERCONNECTIONS IN CONNECTING YOUR SYNTHESIS SYSTEMS SYNTHESIS SYSTEM General Information A Synthesis One installation utilizing the benefits of bi ampliti cation of the front speakers incorporates a total of 4 power amplifiers 2 551605 and 2 58005 Eight of the ten chan nels on the S5160s are to be used for driving the HI fre quency and LO frequency inputs on the left center and right speakers as well as the two side ambient speakers as indi cated in the charts on page 8 Please refer to the connection chart on the following page Use the simplified connection diagrams on the following pages to help you understand how to connect the S5160 amplifier to a JBL Synthesis System These diagrams are intended to show the signal flow through the system For more detail in making these connections please refer to the JBL Synthesis Certified Dealer Installation Manual Connect DIN and audio cables between system components as shown on the following pages Make sure that on all power
19. ire the speakers with the proper polarity reversing any speaker s connections will not damage either the speaker or the amplifier but will result in poor low frequency performance and imprecise imaging WARNING Terminals marked with the flash symbol are hazardous when live External wiring connecied to those terminals requires installation by trained personnel and the use of ready made lead cords NOTE The minimum load impedance that this amplifier can handle safely is eight ohms per channel Using lower impedance loads can damage the unit and will void your warranty Wire Run Length Minimum Gauge Up to 20 Up to 50 Up to 100 6 External Fuses AC mains fuses are located on the back panel of the amplifier These fuses will not blow unless the amplifier is asked to produce more power than its design allows for a prolonged period or to prevent excessive current drawn that could damage internal components during a fault con dition The amplifier has been designed to operate under virtually all conditions Even momentary short circuiting of the out put speaker connections will not ordinarily damage the outout circuitry although this will activate internal protective circuitry and cause one or more of the front pane LED indicators to extinguish until the circuit resets Fuse Replacement To remove the fuse turn off the power switch and discon nect the power plug from the AC mains Unscrew the fuse holder cap a
20. l pushbutton power switch is left in the ON in position See the description of the Manual On Auto On switch for more information on turning on the 55160 2 Standby Indicator red This indicator immediately above the front panel power Switch will glow red when the amplifier is in the standby mode whether operating as part of a Synthesis system or not When the S5160 is in the operate mode this light will shut off and the blue operate mode indicators will light 3 Power Indicators blue These indicators will light up when the power amplifier is in the operate mode Each monitors the operation of one channel and will extinguish if that channels protective cir cuit is activated 10 4 Input Jacks Ch 1 thru Ch 5 The outout signals trom the Synthesis digital processor and equalizer are connected to the input jacks in a Synthesis one System We suggest the channels be assigned as fol lows Amplifier 1 Channel 1 Center Low Frequency Channel 2 Center High Frequency Channel 3 Right Front Low Frequency Channel 4 Right Front High Frequency Channel 5 Right Rear Surround Amplifier 2 Channel 1 Right Side Surround Channel 2 Left Side Surround Channel 3 Left Front Low Frequency Channel 4 Left Front High Frequency Channel 5 Left Rear Surround OPERATION AND CONTROLS NO USER SERVICEABLE PAR S INSIDE REFER 5160 230 SERVICING TO QUALIFIED PE SONNEL POWER AMPLIFIER En f
21. n your entertainment system just one touch on the remote con trol of the surround processor and youre a few seconds away from a truly impressive audio presentation Modern amplifiers produce more power per channel and frequently have more channels than those of the tradition al two channel stereo era Due to the high current demands of power amplifiers at the instant of turn on the 55160 S7150 and S800 amplifiers and the SDEC digi lal equalizer are equipped with power sequencing circuits which turn on each unit in sequence avoiding the large instantaneous current demand and possible house circuit breaker tripping that would occur should they all turn on at the same instant 2 0 INTRODUCTION AND FEATURES Quiet Cooling The S5160 utilizes a fan to cool the amplifier channels ensuring long term reliability To reduce fan noise to an absolute minimum a thermal sensing and control circuit has been incorporated in the Synthesis S5160 that sens 65 increases in temperature within the amplifier and pow ers a fan at a speed proportional to that temperature increase When the S5160 is used at lower volume levels the fan tums very slowly and quietly At high listening levels and the higher operating temperatures this creates within any amplifier the sensing circuitry causes the fan to turn faster producing increased cooling As a result the fan is never turning faster than necessary and most of the noise that is generated is
22. nd remove the fuse install the new fuse and secure the holder cap and reconnect the AC mains If after replacing the fuse the unit is inoperative service 5 required contact your JBL Synthesis dealer WARNING Always unplug the amplifier from the AC mains before removing any fuse IMPORTANT Never install a fuse that has a higher rating than that specified on the back panel of the amplifier or in the owners manual 3 0 OPERATION AND CON TROLS 7 Auto On Manual On Switch Put this switch in the Auto On position if the amplifier is being used as part of a JBL Synthesis System When used in this way the S5160 will automatically turn on when the power switch is depressed and the surround processor is activated For other installations or should individual control of each component be desired put this switch in the Manual On position The amplifier will then be controlled solely by the front panel switch 8 IN OUT DIN Jacks If you are using the amplifier as part of a JBL Synthesis System it is necessary to use these jacks to interconnect to other system components so that control signals power on off and music cinema mode switching can be trans mitted from one unit to the next starting at the surround processor through the equalizer and amplifiers and ending at the speakers Follow the connection diagrams on the following pages for detailed information regarding these connections Make connections to these jacks only as
23. o m D ATTENTION UTILISER cn Baws ma wewe Fo O O Niteummeosrares Input Input Input Pe ype Rectas Input Ea OF AMERICA 32 O 2 SPKR 000000000 9909000 a R Minimum Impedance Minimum Impedance Minimum Impedance 1 8 Ohms A ame Ch 1 Output Ch 2 Cutput Ch 3 Cutput 8 Ohms 8 Ohms QO s Oo OKO O50 OKO OKO OKO OKO OKO OKO Ovo Q TAAL 250VAC o o o o O O O o O O O o O O O O o o O O O o o O O O O O O O O o o o o O O O O O O O O O 00000000000000000000000000000000000000000000000000 F2 PROPER SPEAKER JAL BEFO MANUAL gt AUTO 000000000 Minimum Impedance Minimum Impedance T4AL 250VAC hm O O An 220 240V 900W Ch 4 Cutput Ch 5 Output SUE 3 S9160 230 5 Speaker Terminals Connect the speakers to these terminals following the nor mal convention wire the side of the speaker to the red terminal and the side to the black terminal W
24. provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides informa tion with regard to proper grounding of the mast and sup porting structure grounding of the lead in wire to an anten na discharge unit size of grounding conductors location of antenna discharge unit connection to grounding elec trodes and requirements for the grounding electrode See Figure 1 pp PrEcACfons 18 An outside antenna system should not be located in 23 When replacement parts are required be sure the the vicinity of overhead power lines or other electric light service tech nician has used replacement parts specified or power circuits or where it can fall into such power lines by the manufacturer or that have the same characteristics or circuits When installing an outside antenna system as the original part Unauthorized substitutions may result extreme care should be taken to keep from touching such in fire electric shock or other hazards power lines or circuits as contact with them might be fatal 24 Upon completion of any service or repairs to this 19 Do not overload wall outlets extension cords or inte product ask the service technician to perform safety gral convenience receptacles as this can result in a risk of checks to determine that the product is in proper operat fire or electric shock ing condition 20 Never
25. qu es N ins rez pas d objets dans les fentes d a ration Emp chez tout liquide de se r pandre sur l appareil Ce produit est muni d une fiche trois fils pour la mise terreee Ceci est une mesure de s curit et ne doit pas tre contrari e Ne connectez jamais damplificateurs audio directement aux connecteurs de l appareil Pour emp cher les chocs lectriques et le danger d incendie vitez d exposer lappareil la pluie ou a humidt et ne le mettez pas en marche en un endroit o il serait expos aux claboussures d eau N essayez pas de faire fonctionner l appareil s il est tomb terre a t endom mang expos un liquide ou si vous observez des diff rences nettes dans son fonctionnement indiquant la n cessit de r parations Cet appareil ne doit tre ouvert que par un personnel de service qualifi En enl evant les couvercles vous vous exposez ades tensions lectriques dangereuses Ce triangle sur votre appaeil vous avertit de la pr sence de ten sion dangereuse non isol e l int rieur du boitier une tension suffisante pour repr senter un danger d electrocution Ce triangle sur sur votre appareil vous invite de suivre d impor tantes instructions d utillisation et d entretien dans la documen tation livr e avec le produit _ Espa ol Instrucciones importantes de sequirdad Guarde esta instrucciones para uso posterior Utilice siempre el voltaje correcto Dirfjase a las ins
26. r i ytelsen tyder p at det trenger service Dette apparatet skal kun pnes av fagfolk Hvis dekselet fjernes utsettes man for livsfarlig hayspenning Komponenten er merket med denne trekanten som er en advarsel om at det finnes uisolert farlig spenning inne i kabi nettet h y nok til utgj re en fare for elektrisk stat Komponenten er merket med denne trkanten som betyr at den tilh rende litteraturen inneholder viktige opplysninger om drift og vedikehold Suomi T rkeit varten S ilyt n m ohjeet tulevaa k ytto varten Seuraa kaikkia yksikk n merkittyj ohjeita ja varoituksia K yt aina oikeaa verkkoj nnitett Tehovaatimukset selvi v t valmista jan k ytt ohjjeista Huomaa ett eri k ytt j nnitteet saattavat vaatia toisenlaisen verkkojohdon ja tai pistokkeen k yt n l asenna yksikk telineeseen jossa ei ole tuulet usta tai v litt m sti l mp tuottavien laitteiden esim tehovahvistimien yl puolelle Ymp rist n l mp tila k yt ss ei saa ylitt twotespesifikaation mak simil mp tilaa Kotelo on varustettu tuuletusreiill ja aukiooa Luotettavan toiminnan varmistamisksi ja ylil miseksi n it aukkoja ei saa sulkea tai peitt Mit n esineit ei saa ty nt tuuletusaukkoihin Mit n nestrit ei saa kaataa yksikk n Tuote on varustettu 3 jjohtimisella maadoitetulla verkkipistokkeella T m on turvallisuustoiminne eik sit saa poistaa
27. rrect source has been connected and selected 2 Make sure that the correct outputs are connected from the surround processor or equalizer to the amplifier 3 Make sure that the speakers are connected to the correct ter minals Check for short circuits at both ends of the speaker cables Problem Not all of the amplifiers turn on in a Synthesis system 1 Make sure that all required DIN cables are connected between system components Refer to the CONNECTING YOUR SYN THESIS SYSTEM section 2 Make sure that each amplifier has its Auto On Manual On switch in the Auto On position TROUBLESHOOTING Problem insufficient audio from the speakers Check that the output levels of the surround processor or equalizer are set properly Problem insufficient bass Verify that the speakers have been wired to the amplifier with the correct polarity Problem Front speakers do not switch from music to cinema mode 1 Make sure that the screw terminal and DIN adapter cables to speakers are correctly wired and are connected to the correct Jacks on the S5160 2 Make sure that all required DIN cables are connected between system components Problem Audible hum from the speakers 1 Check the power outlets and make sure that there is a solid earth ground present The services of an electrician may be required 2 Make sure that all signal cables are routed away from power cords 3 If these suggestions fall experiment by
28. sanweisungen auch f r sp ter auf Befolgen Sie alle auf der Vorrichtung stehenden Anweisungen und Warnungen Immer nur mit der richtigen Spannung verwenden Die Gebrauchsanweisungen des Herstellers informieren Sie ber die elektrischen Anforderungen Vergessen Sie nicht da bei vershiedenen Betrievsspannungen ggf auch verschiedene Leitungskabel und oder Verbindungsstacker zu verwenden sind Stellen Sie die Vorrightung nicht in ein unbel ftetes Getell oder unmittelbar ber w rmeerzeugende Ger te wie z B Tonverst rker Halten Sie die in den Produkt spezifikationen angegebene maximale Umgebungstemperatur bei Betrieb ein Schlitze und ffnungen im GehUause dienen der Beltifung um verlaBlichen Betrieb sicherzustellen und Uberheizen zu vermeiden d rfen diese ffnungen nich verstopft oder abgedeckt werden Stecken Sie nie irgend einen Gegenstand durch die Bel ftungsschlitze Vergie en Sie keine Fl ssigkeiten auf den Apparat Dieses Produkt is mit einem 3 drahtigen Erdungsstecher ausger stet Diese SicherheitsmaBnahme darf nicht unwirksam gemacht werden Schlie en Sie nie Tonverst rker unmittelbar an einen Anschlu des Apparates an Um elektrischen Schlag oder Feuer zu vermeiden setaen Sie den Apparat weder Regen noch Feuchtigkeit aus und betreiben Sie ihn nicht dort wo Wasser eindringen k nnte Versuchen Sie nicht den Apparat zu betreiben falls er fallen gelassen besch digt oder Fl ssigkeiten ausgesetzt wurde oder falls
29. shown in the diagrams If these jacks are used in any other manner e 9 to control electric screens the unit can be damaged and the warranty will be void For specific elec tical information on these jacks contact JBL Synthesis Customer Service Do not plug anything into these jacks if you are not using the 5160 with a JBL Synthesis System OPERATION AND CONTROLS 9 Speaker Mode Control Connectors The front left and front right speakers are switched between Music and Cinema modes by signals present at both the DIN connectors as described in the previous paragraph AND the 2 conductor connectors shown at The installer may find it preferable to use 2 conductor wire 18 gauge recommended rather than long multi conduc tor DIN cables for the mode switching connection between the S5160 and these two speakers Adapters supplied with the S5160 are used at the speaker end of the wire to allow connection to the speakers DIN input connectors Proper polarity must be observed as shown in the wiring diagrams reverse the connections at one end of the wire if the speaker s do not switch modes from horn Cinema to tweeter Music Note that 5 conductor DIN cables MUST be used between all other components to allow correct power and mode switching and that the same warning not to plug anything into these jacks if you are not using the S5160 with a JBL Synthesis System applies here do not attempt to use these jacks to control anyth
30. sich seine Arbeitsweise derart ndert da daraus ein Bedarf nach Raparatur zu schlie en ist Dieser Apparat sollte nur von qualifizierten Fachleuten ge ffnet werden Das Abnehmen von Abdeckungen setzt Sie gef hrlichen Spannungen aus Dieses Dreick auf ihrem Apparat warnt Sie voe nicht isolierter gef hrlicher Spannung im Geh use stark genug um eine Ber hrungsgefahr darzustellen Diese Dreick auf ihram Apparat bedeutet da wichtige Betriebsund Wartungsanweisungen in der mitgelieferten Dokumentation zu finden sind Fran ais Instructions de S ret Importantes Gardex ces instructions pour r ference future Observez toutes les instructions et tous les avertissements marqu s sur l appareil Branchez uniguements sur un r seau de tension indiqu e Consultez le manuel d instruction du fabriquant pour les sp cifications de courant N oubliez pas que diff rentes tensions peuvent n cessiter l utilisation de cables et ou de fiches deconnexion diff rents N installez pas l appareil en un compartiment non a r ou directement au dessus d quipements g n rateurs de chaleur tels qu amplificateurs de courants etc Ne d passez pas la temp rature ambiante maximale de fonctionnement indiqu e dans les sp cifications du produit Des fentes et ouvertures sont pr vues dans le bo tier pour l a ration Pour assur er le bon fonctionnement et pour pr venir l chauffement ces ouvertures ne doivent pas tre couvertes ou blo
31. side channels to pro duce a truly enveloping sound field When coupled with a high quality subwoofer amplifier such as the Synthesis 5800 it Is a solid foundation on which to build a high performance home cinema system that will astound the listener with its power and realism The 55160 is specially designed for use with a Synthesis One system in which the front left right and center speakers are bi amplified for smoother and more accurate reproduction of every INTRODUCTION ANID FEATURES nuance of a movie soundtrack or musical selection Two 55160 amplifiers may be used in conjunction with 2 S800 subwoofer amplifiers to power a complete 7 1 channel home theater system Alternatively a single 55160 may be used with one S800 subwoofer amplifier to power a 5 1 channel system High Power Capability The S5160 provides a satisfying 160 watts per channel of aistortion free audio lt 0 03 THD into eight ohms Because of their power capabilities all Synthesis amplifiers have an extremely wide dynamic range an element critical to realistic home cinema Sound levels equal to those at original performances are easily recreated in even the largest of home listening environments Auto Turn On and Power Sequencing Circuitry When used in a JBL Synthesis System the S5160 can be turned on automatically whenever the surround proces sor is activated No longer do you have to get out of that chair to turn on the various pieces of equioment i
32. trucciones de operaci n del fabricante para obtener las especificaciones de potencia Est al tanto de que voltajes de operaci n distintos requieren el uso de cable y o enchufes distintos No instale esta unidad en un estante sin vntilaci n ni tampoco directamente encima de equipose que generen calor tales como amplificadores de potencia F jese en las temperaturas ambientales m ximas de operaci n que se mencionan en las especificaciones del producto Las aperturas y ranuras del chasis sirven para proveer la ventilaci n necesaria para operar la unidad con sequridad y para prevenir sobrecalentamiento y por lo tanto no pueden ser obstruidas o cubiertas No introcuzca objetos de ning n tip a trav s de las ranuras de ventilaci n y nunca deje caer ning n l quido sobre la unidad Este producto est equipado con un enchufe de 3 clavijas con conexi n a ierra Este es un elemento de seguridad que no debe ser eliminado Nunca conecte ningun tipo de salida de amplificadores de sonido directamente a los conectores de la unidad Para prevenir descargas el ctricas o incendios mantenga la unidad alejada de la lluvia humedad o cualquier lugar en el que pueda entrar en contacto con ague No trate de hacer funcionar la unidad si se ha ca do est da ada ha entrado en contacto con l tuidos o si nota cualquir cambio brusco en su funcionamiento que indique la necesidad de hacerle un servicio de mantenimiento Esta unidad deber ser abi
33. ualsiasi genere attraverso le fessure di ventilazione Non versare mai del liquido di nessun tipo sull unit QUesto pordotto viene fornito con una spina a 3 fili con massa Tale dispositivo di sicurezza non va leiminato Evitare sempre di collegare le uscite dell amplificatore auio direttamente ai con nettori dell unit Per prevenire il pericolo di folgorazione e di incendio non esporre l unit alla pioggia o ad un umidt eccessiva evitare di adoperare l unit dove potrebbe entrare in contatto con acqua Evitare di adoperare l unit se la stessa stata urtata violentemente se ha subito un danno 56 stata esposta ad un liquido o in caso di un evidente cambiamento dell prestazioni che indichi la necessit di un intervento di assistenza tecnica Ogni intervnto sull unit va esqguito esclusivamente da personale qualificato La rimozione della copertura comporta l esposizione al pericolo di folgorazione II present triangolo impresso sul componente avverte della pre senza di tensioni pericolose non isolate all interno della copertu ra tali tensioni rappresentano un pericolo di folgorazione II presente triangolo imprsso sul componente avverte l utente della presenza nella documentazione allegata di importanti istruzioni relative al funzionament ed alla manutenzione Dansk Vigtig information om sikkerhed Gem denne vejledning til senere brug F lg all anvisninger og advaresler p apparatet Apparatet skal altid t
34. with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an elec trician for replacement of the obsolete outlet 10 Protect the power cord from being convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or wh unused for long periods of time 14 Refer all servicing to qualified service personnel damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate nor mally or has been dropped 15 Do not use attachments not recommended by the oduct manufacturer as they may cause hazards 6 This product should be operated only from the type of ower source indicated on the marking label If you are not ure of the type of power supply to your home consult NOD a O your product dealer or local power company For products intended to operate from battery power or other sources refer to the operating instructions 17 If an outside antenna or cable system is connected to grounded so as to
Download Pdf Manuals
Related Search