Instruction Manual
Contents
1. CAUTION If the nut is loose air will leak and the temperature will drop Pd 3 Maintenance Station Replace the outside filter The filter is expendable it often should be replaced to ensure the suction is normal Pull out the hose each side filter take out it replace the new one See the connection part Cleaning the Pump CAUTION Unplug the power cord before starting this procedure 16 As a QUICK 201B Manual Operation well CK Disassemble the pump heads Disassemble the rear panel and remove the cover take out the pump head from each side of the pump Clean the pump head Remove the valve plate and fixing plate and clear any flux adhering to the plates V CAUTION 1 If the fixing plate is difficult to remove apply hot air to it to warm it up Never use excessive force to remove the plate as it is easy to bend and a bent plate will allow air to leak out and reduce solder vacuuming efficiency 2 Clean the plates only with alcohol or thinner Replace If the valve plate is bent or stiff replace it If the exhaust filter is dirty replace it Assemble the pump heads Reassemble the valve plate and fixing plate I CAUTION When assembling the pump be sure to check for air leaks Be sure the parts a Pump Head are aligned correctly XSA Prol a Valve Plate Fixing Plate VI Replace Parts Replacing the Heating Element V CAUTION Unplug the power cord before star2. O ring in the back holder f Packing and nearby parts 3 LED display does not light up e Is the power cord plugged in correctly Securely insert the power cord into the power supply Is the fuse blown Determine why the fuse blew and eliminate the cause then replace the fuse A Is the inside of the unit short circuited B Is the grounding wire touching the heating element C Is the heating element lead twisted and short circuited 4 Pump does not operate e Is the cord assembly properly connected Reconnect the cord assembly 5 Solder is not being absorbed e Is the spring filter full of solder Replace it with a new one e Is the ceramic filter hardened Replace it with a new one 12 M2U CK QUICK 201B Manual Operation e Is there a vacuum leak Check the connections and replace any worn parts Is the nozzle or hole in the heating element clogged Clean it 6 The nozzle does not heat up e Is the desoldering gun cord assembly properly connected Reconnect it e Is the heating element damaged Is the heating element broken as follow Replace it 5 A Between pins 4 amp 5 Heating element Under 1 2 Normal ie OO B Between pins 1 amp 2 Sensor Under 10 2 Normal 1 ee J jJ3 C Between pins 3 amp Nozzle Under 2 Q Sy 7 Heater error H E lis displayed e Is the desoldering gun cord broken Replace it e Is the heating element broken Replace the heating
3. the password value in the same way described in set temperature normally After selecting the password of three digit press button 5 Ifthe display window shows the present setting The input password is error temperature two seconds later the station is in normal work state This indicates the password of input is error and the temperature setting can t be done The password of input is correct 6 If the display window shows this indicates the password of input is correct After displaying about 4 seconds the station comes into normal work state and the setting temperature will be admitted M2U CK QUICK 201B Manual Operation 7 When display window is showing Input New Password 29399 press button and shows gt It indicates the unit comes into inputting new password state Pressing A or Y button will change displayed value See set temperature normally 8 When three digits are selected press button Repeat the new password a f the display window shows again Now must input the new password Repeat the same steps 9 If the password is the same as last time the changed password is OK The new password is stored into the internal memory 10 If the password is not the same as last time and the display window shows the station will ne ed to rewrite new password see the last 8 9 step The changing of password is finished until t
4. element e Is there a nozzle on the gun Assemble a nozzle on the gun 8 Can t set the temperature Is the button on the panel locked by password Enter into the setting password Note When repairs are needed please send both the desoldering gun and the station to your sales agent VI Maintenance and servicing Properly maintained the desoldering gun should provide years of good service Efficient desoldering depends upon the temperature and the quality and quantity of the solder and flux Perform the following service procedures as indicated by the conditions of the gun s usage Warning Since the desoldering gun can reach a very high temperature please work carefully Except when cleaning the nozzle and heating element always turn the power switch off and disconnect the power plug before performing any maintenance procedure 1 Post operation Maintenance TO ensure a long service life always perform the following maintenance procedures immediately after using the unit Remove all solder from the inside of the nozzle and heating element 13 lt eU CK QUICK 201B Manual Operation Clean the tip of the nozzle with the cleaning sponge then coat the tip with a fresh layer of solder to protect the solder plating 2 Servicing the Desoldering Gun CAUTION The desoldering gun will be extremely hot During maintenance Please wear gloves and work carefully Inspect and clean the nozzle e
5. set Press or w button LL C4 45 4 Select the desired value for the 1 s digit Aree ec Using the A or Y button will change 459 displayed value as shown above for the 10 s place selection Press the button Here pressing the button a enters the temperature setting into the internal memory b displays the temperature setting and c starts heater control Note If you turn off the power switch during the temperature setting setting value will not be stored in the memory If the temperature value outside of this range is selected the display will return to flashing the 100 s place If this happens reenter a correct temperature value Set temperature on line In the work if it is necessary to set temperature quickly and the heat elements can not be cut off the way may be selected Temperature rising Don t press knob and press knob directly If so the setting temperature will raise 1 C and the display window will display the set temperature When loosen the A knob the display window will display the set temperature about 2 seconds If within 2 seconds of time press the A knob again the setting temperature will raise 1C again If press the A knob and not loose at least 1 second the setting temperature will rise rapidly Till the needed temperature reaches then loose the A knob Temperature dropping Don t press knob
6. used for 20 minutes the power to the heating element will be decreased and the display shows gt gt This state is sleeping mode When the unit is in sleeping mode the nozzle temperature will decrease to 200 C if the set temperature is more than or equal to 200 C or 50 C if the set temperature is less than 200 C and remain the temperature until resuming the unit To resume soldering there are several ways as follows 1 Cycle the power switch OFF then ON 2 Hit any button 3 Press the trigger of gun If the unit is not resumed more than 40 minutes after it comes to sleep the power supply will be shut off automatically and the display window will not show anything 6 Calibrate Temperature The desoldering gun s temperature should be recalibrated after replacing the iron or heating element or nozzle every time The unit adopts digital calibration mode and input the revision value is input by pressing button make the adjustment simply and quickly As QUICK 201B Manual Operation n u E K Method of recalibrating temperature Use the thermometer to calibrate and it is precise comparatively Calibrate by using thermometer 1 Set the unit s temperature to a certain value 2 When the temperature stabilizes measure the nozzle s temperature with thermometer and write down the reading 3 Press x button not loose and press the A and VW button simultaneously the soldering station enters int
7. B _ Solder ee Lead Slowly move the lead with the nozzle Absorb the solder by slowly moving the lead back and forth with the tip of the nozzle lt eU CK QUICK 201B Manual Operation V CAUTION Never leave any solder remaining inside the hole in the P W B Problems during desoldering If solder remains resolder the component and repeat the desoldering process Clean the tip of the nozzle Keep the solder plated section of the nozzle a shiny white by coating it with a small amount of solder If the tip of the nozzle is coated with oxide the nozzle s heat conductivity will be lowered Coating the tip with a small amount of fresh solder ensures maximum heat conductivity Wipe away any oxide or old solder from the nozzle using the hole in the center of the sponge IV Cleaning During the Process of Operation The solder absorbed by nozzle must be cleaned in time to insure the unit work normally 1 Observing the Indicator While looking at the indicator and with the hole of the nozzle open pull the trigger and look at the indicator If it is red clean the nozzle and heating element empty the filter pipe and replace the filters If the indicator is blue cleaning is not necessary and operations can be resumed Vs CAUTION The indicator will not operate accurately if the hole of the nozzle is closed or if the solder in the hole of the P W B is not melted If there is a noticeable drop in suction e
8. B 350 450 C Multi layer P W B Set temperature normally CAUTION Make sure the temperature of the unit can be adjusted password is OK or the password is initial While setting the temperature normally the heating element is off If the button is pressed for less than one second the present temperature setting will be shown for two seconds and then the display will return to showing the nozzle temperature A VY Choose the value k Choose the digit Example 400 C to 350 C 1 Push the button and the hold it down l for at least one second The left most digit the 100 s digit in the display will flash 400 This indicates that the station is in Press button once A temperature setting mode and that the 100 OU s digit can be adjusted 8 J 2 Select the desired value for 100 s digit 2 Using the A or Y button will change displayed value as follows Oo es ee Press the button when the desired value is displayed This will cause the middle digit the 10 s digit in the display to begin flashing M2U CK QUICK 201B Manual Operation 3 3 Select the desired value for the 10 s digit Using the A or Y button will change LL Co displayed value as shown below ee eee Press button ones Press the button The right the 1 s digit will then begin flashing to indicate that the 1 s digit can be 4
9. Plug in the power cord turn the power switch On and let the nozzle heat up e Clean out the hole of the nozzle heat up The cleaning pin passes completelv through the hole V CAUTION The cleaning pin will not pass through the nozzle until the solder inside the nozzle is completely melted Please use the proper sized cleaning pin for the nozzle diameter e Check the condition of the solder plating on the tip of the nozzle Solder plating l Diameter of hole is J widened through erosion e If it is slightly worn recoat the tip with fresh solder to prevent oxidation e Check the condition of the surface and inside hole of the nozzle e If either is worn or eroded or the inside diameter seems unusually wide replace the nozzle A CAUTION 1 Unfortunately it is often difficult to observe this condition Therefore if desoldering efficiency goes down and all other parts appear to be OK the nozzle is probably eroded and should be replaced 2 The inside hole and the surface of the nozzle is plated with a special alloy Should this alloy become eroded by high temperature solder the nozzle will not be able to maintain the proper temperature 14 M2U CK QUICK 201B Manual Operation Disassemble the heating element Remove the nut with the heat resistant pad Heating Element Element Cover Nozzle Nut Clean out the hole in the heating element with the provided cleaning pin CAUTION Be sure the solder in
10. QUICK 201B Desoldering Tool Instruction Manual Thank you for purchasing this desoldering tool Please read manual carefully before using Store this manual in a safe easily accessible place for future reference QUICK 201B Manual Operation I Specification M2U CK In this instruction manual WARNING and CAUTION are defined as follows WARNING Misuse may potentially cause death of or serious injury to the user CAUTION Misuse may potentially cause injury to the user or physical damage to the objects involved For your own safety be sure to comply with these precautions Specification Power of the pump Power of heating Temperature of nozzle Pump Vacuum suction Nozzle to ground resistance Nozzle to ground potential Dimension Weight Il Part Names 1 Desoldering Gun Nozzle Transmits heat for melting solder Entrance for melted solder Expendable part Heating Element Inside requires cleaning Trigger Squeeze to start absorption Do not pull the trigger before fully heating the nozzle 12V 2A 90W 36VAC 400KHz 200 C 450 C See the working mode table Diaphragm pump 600mmHG Less than 2 Q Less than 2mV 105 W X 250 D X 165 H mm 4 8Kg With iron holder and power cord Filter pipe Inside the ceramic paper filter S Contains melted solder and flux using spring filter Spring filter are expendable parts Back Holder Assembly Secures the filter pipe Release Knob Push down to
11. and press Y knob directly If so the setting temperature will drop 1 C and the display window will display the set temperature When loose the Y knob the display window will 4h a QUICK 201B Manual Operation well CK relay the set temperature about 2 seconds If within 2 seconds press the Y knob again the setting temperature will drop 1 C again If press the V knob and not loose at least 1 second the setting temperature will drop rapidly Till the needed temperature reaches then loose the Y knob 4 Set Parameters The station has the following parameters Parameters setting can be adjusted password The initial password in station s memory is 000 The setting temperature is admitted in this state If need to restrict the setting temperature the password must be changed Enter into setting the password 1 Turn off the power switch Press and hold the A and VY buttons simultaneously then turn on the power switch 2 Continue holding down the A and Y button until the display shows 3 When the display shows l the station is in parameter input mode Input Previously Password 4 Press the button the display shows and the left most digit the 100 s digit in the display will flash This indicates the station is in password setting mode and the 100 s digit can be adjusted Using the A or Y button will change displayed value Set
12. fficiency clean the nozzle and heating element with the cleaning pin Normal Abnormal Solution Blue or slight More than half of the If the indicator is more than half red replace the amount of red can indicator is red filter and clean the nozzle and the inside of the be seen heating element 10 M2U CK QUICK 201B Manual Operation 2 Replacing the Filter Pipe Replace the filter pipe as shown step During operation the filter pipe is very hot Wait until the filter pipe is cool before replacing the filter We recommend keeping a second filter pipe containing new filters handy and replacing the installed filter pipe with this backup filter pipe Replace the entire filter pipe with the provided backup filter pipe Automatically spring y z Pull down V Error Messages Various error messages will be displayed when there is a problem with the unit If the following message is displayed see the trouble shooting guide If there is a possibility of a failure in the sensor or S E Sensor Error anywhere in the sensor circuit will be displayed and power to the soldering iron will be cut off If power is being sent to soldering iron and the tip Flash the Temperature Display temperature goes below the setting temperature Note about 80 C the temperature display will flash Draw your attention to this H E Heater Error If power can t be sent to soldering iron t
13. he display window will show s B This indicates the possibility of a heater malfunction VI Trouble Shooting Guide i Warning Disconnect the power plug before servicing Failure to do so may result in electric shock 11 M2U CK QUICK 201B Manual Operation Tf the power cord is damaged it must be replaced by the manufacturer its service agent or similarity qualified person in order to avoid personal injury or damage to the unit 1 The solder in the junction is not sufficiently melted e Temperature is not high enough The following parts require a greater heat capacity to desolder Use a preheating oven or heating gun to heat the P W B to a temperature that won t damage the board or its components then desolder Do not only increase the temperature of the gun otherwise too high temperature may damage the P W B and its components e Nozzle is worn out When the nozzle begins to wear out the heating efficiency begins to decline Check the nozzle If the solder plating is damaged or the nozzle is eroded replace the nozzle 2 Suction power is dropping Replace the filters and clean the nozzle and the inside of the heating element e Air is leaking from the vacuum system Air leakage cannot be determined from the indicator Check the air tightness of the following parts and replace that are worn a Contact point of the nozzle and heating d Hose b Front holder and nearby parts e The tie in c
14. he lately two passwords are identical Note The word of password is 0 to 9 ten words If not the changed password is unsuccessful Working Mode Working Mode Setting If the display window shows press and hold the A and V buttons simultaneously then the display shows This indicates the unit comes into working mode setting state and pressing A or VY button will change displayed valve as shown below C gt lt gt a 0 lt gt 1 4 After selecting the working mode press down The working mode is stored into the internal memory As a QUICK 201B Manual Operation well CK Please refer to the Working Mode Table for the meaning of the digit displayed Note X represents the original working mode digit Warning The heater and soldering tips will be seriously oxidized or damaged when working with a high temperature So please choose the working mode carefully and try to operate with a lower temperature if possible Working mode table Working mode Temperature range Handle type Remark 0 200 C 450 C Desoldering gun and Soldering iron Auto sleeping 1 200 C 480 C Desoldering gun and Soldering iron Auto sleeping 0 200 C 450 C Desoldering gun and Soldering iron No sleeping L 200 C 480 C Desoldering gun and Soldering iron No sleeping 5 Sleeping If sleeping and working mode are selected and the desoldering gun is not
15. lure to de so may damage the P W B 1 Connect the metal plug of cord assembly to the receptacle marked IRON IRON Align the grooves and pins and push stranght in Turn clockwise firmly 2 Connect the external filter to the tie in s hose marked VACUUM in accordance with the mark on the external filter need to insert fully and connect the other side of filter to desoldering gun s hose CAUTION The external filter have connection orientation and connecting according to mark otherwise affect suction VACUUM Va Connect to main unit lt Fully insert filter into the hose gt Airflow direction Connect to gun Filter is expendable As a QUICK 201B Manual Operation well CK 3 Plug the power cord 4 Turn on the power switch and LED display is light the desoldering gun begins to heat up The heater lamp flickers when the temperature has stabilized CAUTION After turning the power switch to ON wait 3 minutes before beginning desoldering operations 3 Set the Temperature CAUTION Always set the temperature to as low as possible for the work being done The unit have two kinds of temperature setup Normal temperature setup and instant one The temperature can be set between 200 C and 480 C with temperature control knob Please refer to the chart below and set the temperature Temperature P W B 280 350 C Single sided P W B 320 400 C Through hole P W
16. o calibrating temperature mode 4 At the moment the 100 s digit of LED display temperature is flashing Press the A and V button to select the value and press button to select the digit Input the reading of thermometer and inputting method is the same as Set temperature normally Press button after inputting Here the whole calibration operation has been finished 5 If the temperature still has deflection you can repeat calibration in accordance with above steps We recommend to use the 191 192 thermometer for measuring the tip temperature Tf the unit is locked by password it will not be able to calibrate the nozzle temperature and you must input the right password 7 Operate Melt the solder Apply the nozzle to melt the solder after the temperature stabilizing V CAUTION 1 Never allow the nozzle to touch the board itself 2 To confirm that all the solder is melted observe the inside of the hole and the back side of the P W B If this is difficult to do try slowly moving the lead with the nozzle if the lead moves the solder is melted 3 Never move the lead by force If it doesn t move easily the solder isn t yet fully melted Absorb the solder After confirming that the solder is completely melted absorb the solder by squeezing the trigger on the gun After fully absorbing all the solder cool the soldering junction in order to prevent it from becoming resoldered ie Nozzle P W
17. remove the filter pipe Indicator Indicates when nozzle and heating element need cleaning and when filters need replacing Hose Connects to the outside filter Cord Assembly Connects to the receptacle M2U CK QUICK 201B Manual Operation 2 Unite Receptacle Connect with the LED Display Display the setup temperature cord assembly lt s s se 6 ve LED Heater Display Lamp Tie in A h x amp es _ CS TEMP Control Button Set and control temperature Connect with filter VACUUM IRON POWER When turned to ON the heating element starts to heat up Power Switch Grounding Hole Connect with grounding wire Power Socket Connect with Power cord lt eU CK QUICK 201B Manual Operation III Installation and Operation i CAUTION Before setting please check whether the voltage accords with the rated voltage on the unit s nameplate 1 Iron Holder and Sponge i CAUTION The sponge is compressed It will swell when moistened with water Water and squeeze it dry Failure to do so may result in damage to the nozzle Take out the desoldering gun and put it in the iron holder 2 Dampen the cleaning sponge with water and then squeeze it dry Be sure to remove the round portion of the sponge and place it in the iron holder 2 Connections CAUTION Be sure to turn off the power switch before connecting or disconnecting the cord assembly and the power plug Fai
18. rigger 17 47011 Heating Element 24285 0 8mm Nozzle A1004 0 03in Expendable 18 24284 1 0mm Nozzle A1005 0 04in Expendable 24283 1 3mm Nozzle A1006 0 05in Expendable 19 44235 Element Cover 20 44006 Nut 21 43001 Iron Holder 22 20011 Cleaning Sponge 23 41001 4 Filter Pipe Without Front Holder amp Spring Filter 24 42326 External Filter E Expendable 20
19. the hole in the heating element is completely heated Before cleaning the hole If the cleaning pin cannot pass through the hole replace the heating element Turn the power off after cleaning Replace the filters Turn the power switch OFF When the filter pipe is cool to the touch push down the release knob at the back of the gun and remove the filter pipe Front Holder Spring Filter ais Ceramic Paper S CAUTION The filter pips is very hot Inspect the front holder Replace Stiff and cracked Inspect the spring filter Replace Solder is collected in two thirds of the spring filter e Inspect the ceramic paper filter S Replace Ceramic paper filter is stiff with flux and solder Secure the filters Attach the spring filter to the front holder Attach the front holder to the filter pipe V CAUTION 1 Be sure the front holder is correctly aligned 2 Use the ceramic paper filter S for the filter pipe gun Using of the ceramic paper filter L in the filter pipe may cause to break or the power to drop 15 lt eU CK QUICK 201B Manual Operation Ceramic Paper Filter S Attach the front holder to the filter pipe so that it does not leak air Firmly press the back holder assembly into the filter pipe in order to properly seat the O ring against the pipe Assemble the heating element e Attach the nozzle and securely tighten the nut with the attached heat resistant pad
20. ting this procedure The resistance value of a working heating element is below 1 Q at 23 C If the value you get is outside this range replace the heating element Disassemble the heating parts 2 Separate the housing 8 Detach the terminal and remove the heating element Insert a new heating element and reassemble Heating element36V 90W 17 Ai QUICK 201B Manual Operation n u E K Recalibrate the temperature The resistance of new heating element varies resulting in variations in operating temperatures It is necessary to recalibrate the temperature every time the heating element is replaced See the Calibrate temperature Remove the filter pipe Housing Unscrew the screws Detach the terminal Pad 0 18 QUICK 201B Manual Operation IX Replaceable Parts Parts List Desoldering Gun 19 QUICK 201B Manual Operation lt 2U CK Item No Part No Part Name Description 1 45001 Front Holder 2 14001 Spring Filter Without Front Holder amp Spring Filter 3 47044 Ceramic Paper Filter S i oor eee With Front ae n Filter 5 26099 O ring 6 47002 Back Holder Assembly 7 42001 Release Knob 8 14002 Spring For Release Knob 9 41001 Housing 10 55049 Hose 11 45002 Packing 12 47003 Cord Assembly w Micro Switch amp Plug 13 42148 Cord Holder 14 44043 Cord Stopper 15 12128 Micro Switch 16 42005 T
Download Pdf Manuals
Related Search