PRG 2660 - User Manual - Balogh technical center
Contents
1. IC 485S e LPR power connector unit for the LPR 3011 e g Mascot 9886 type ending with a suitable connection unit 3 2 2 CONFIGURING THE READER IN THE CASE OF THE LPR 3010 e Place the reader without power supplied on a table e Unscrew the two screws holding the cover and remove the latter e Unscrew the screw next to the light which holds the lid and remove the latter e Position the micro switches in order to get the following configuration refer to the sheet included or to interfacing manual ref 13053 104 J1 interface in RS 422 or RS 485 as desired by the user J2 adress choose a JBus address between 2 and 12 by default that of PRG 2660 is 1 J3 mode in polling and JBus e Connect the network cable to the reader terminal block JP1 push it in until it locks e Connect the power to the reader terminal block JP3 push it in until it locks e Replace the lid and re tighten the screw e Replace the casing and tighten the two screws p 11 BALOGH SA 189 rue d Auberviliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification R f UM PRG 2660 V1 3 EN 3 2 3 CONFIGURING THE CONVERTER Configure the converter in data transmission interface DCE The handshake signals depend on the type of network RS 422 PC RS232 Convertisseur 4 RS232 RS422 4 config RS422 RX interrupteurs DCE T ON TX R ON RX PRG config RS422 RX GND HS 485 1 1 2 PC RS232 Convertisseur 2 22. Program Code Programing Box Status lssuer Code 225 Name ASVA Enable Issuer Format ASCII Made NORMAL im Input Tag code Of XJ Code Load Format Data base coe Change Mode e NEM keyboard Read Tags code verify serial number Change Mode Setup Port About p 9 BALOGH SA 189 rue d Auberviliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification R f UM PRG 2660 V1 3 EN Example programming with all options prefix 777 suffix 666 The tag with serial n 353302840 is to be programmed with 001 this data must be entered via w Input Tag code OF x Code vom PRG WIN3 2 Biel aM 253302840 Program DIS Programming Box Status mer E Loser Code 2B M ame ASYA SEN EE Format ASCII Mode NORMAL E S PER Load Farmat Data base Change Mode ww Ir keyboard Read Tags code verity F serial number M show last code MW code incremented Exil Setup Part About In the Display Messages zone the following appear e onared background the complete code proposed for the next tag Code to program e ona blue background the serial n proposed for the next tag S N Confirm these values via Program Code Exit the last time At the end of the programming session select the Exit button the application creates in the application s repertory a renamable text file
3. txt which keeps track of the operations performed Example Date 06 05 04 16 52 05 PRGWIN32 version 1 2 16 M Mode N NORMAL F FAST P POWER DOWN F Format A ALPHANUM W WIEGAND T TEST IC Issuer Code PRG2660 version 3 01 Check S N Tag Code XX 353302840 777001666 35330284 1 777002666 p 10 BALOGH SA 189 rue d Auberviliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification R f UM PRG 2660 V1 3 EN 3 PROGRAMMING WITH CODE CHECKING 3 1 PRINCIPLE To be absolutely sure that the coding is correct the code programmed must be read by a Hyper X reader The programming software allows programming and checking to be linked subject to the interconnection of the Hyper X reader with the PC and the PRG 2660 in a RS 422 or RS 485 network RS 422 RS 485 netw ork PRG2660 encoder HY PERX reader ooa tag The reader usually a LPR 3011 reduced to a 0 5 m range is interrogated repeatedly for 5 s after the coding The PC sends a JBus command to the reader to repatriate the code and performs the check any anomaly is flagged up N B in automatic incrementation mode see paragraph 3 2 6 the incrementation takes place only if the reading result is identical to the code input 3 2 CONFIGURATION 3 2 1 NECESSARY ACCESSORIES e An RS 232 RS 485 converter for PC e g IC 485S Roline brand e Network cable e g Y cable connected to the converter e Converter power supply 9 V for the
4. BALOG PRG 2660 User Manual Ref UM PRG 2660 V1 3 EN BALOGH SA BALOGH TAG 189 Rue d Aubervilliers CP 97 75886 Paris 3637 Old US 23 Cedex 18 France Brighton Michigan MI 48114 USA Tel phone 33 0 1 44 65 65 00 Tel USA 800 252 RFID 7343 Fax 33 0 1 44 65 65 10 810 360 0182 Web http Avww balogh rfid com Canada 800 258 RFID 7343 Fax 810 360 0237 Page intentionally left blank FOREWORD The purpose of this manual This technical manual describes the programming of BDG tags It completes the PRG 2660 interface manual and general presentation sheet Manual reference The manual s generic reference is UM name of equipment Vx y L where UM means user manual x designates the equipment s version number y designates the document issue revision number L is the language used Update No Not used 31 07 07 Creation based on documentation M PRG 2660 1 1 F 09 10 08 Flyleaf modification 10 06 14 Annexe modification il Lee ee ON Note The information contained in this manual are subject to being changed without notice BALOGH cannot be held responsible for the possible consequences of any errors or omissions nor of interpretation of the information therein JBUS a registered trade mark of April p 3 BALOGH SA 189 rue d Aubervilliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification R f UM PRG 2660 V1 3 EN TABLE OF CONT
5. ENTS TI DESCRIPTION WE Job PRO 2660 PROGRAMMER sine et 1 2 INSTALLATION AND CONNECTION errr eee ea ater ee 2 PROGRAMMING EE 24 QONPIGUBATIODN EE 2 1 1 CONFIGURING THE PC S SERIAL POR EE 2 1 22 CONFIGURATION OF THE PRGWIN32 APPLICATION 2 2 IMPLEMENTATION EE 3 PROGRAMMING WITH CODE CHECKING gk PRINGIPLE sid eo eme essence mee senc cine none diese an 9 EH TION EE 3 2 1 NECESSARY ACCESSORIES ns ea tre 3 2 2 CONFIGURING THE READER IN THE CASE OF THE LPR 3010 32 0 CONFIGURING THE CONVERTER ss ipe sacs erunt TG 3 24 CONFIGURING THE PROGRAMMING BOX UN 3 25 CONFIGURING THE SERIAL PORT OF THE PC AND THE NETWORK 3 26 CONFIGURING THE PRGWIN32 APPLICATION sssssssssessssensseenessrressrrrerreenn 3 39 IMP EMENTATIONE eto ist E t RE E SO od le E A ERROR MESSAGES cccssccccscsseccccessecccccsssccscosssccssessseossessssoncenssseucesssseess ANNEXE 1 CONFIGURATION OF THE PROGRAMMING BOX ANNEXE 2 BDG 1090 PROGRAMMING WITH ADAPTER BALOGH SA 189 rue d Aubervilliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification R f UM PRG 2660 V1 3 EN p 4 1 DESCRIPTION 1 1 PRG 2660 PROGRAMMER The PRG 2660 tag programmer is composed of e aPC application Windows supplied on CD ROM e aprogramming box in ABS for placing on a table e a power supply e a3 wire RS 232 cable without pin 2 3 reverser The p
6. TX LPR R35232 RS485 3 L config R5485 cn jE co GND Interrupteurs DCE TX T RTS 2 TX R RTS Rx PRG x config RS485 p 12 BALOGH SA 189 rue d Auberviliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification R f UM PRG 2660 V1 3 EN 3 2 4 CONFIGURING THE PROGRAMMING BOX e Turn the programming box with no power supplied over on a table e Unscrew the four Pozidriv crosshead screws that hold the cover and remove the latter G9 co O e Put the programming box back in its place e Position micro switches J3 and J4 RS 422 485 s switch ON RS 232 BI J so that you have the following configuration J3 mode in RS 422 or RS 485 depending on which has been chosen J4 address between 1 and 15 different from that of the reader transmission speed identical to that of LPR 3010 Mode Address WNWkNNN J3 seme JA Nk RS 422 wi RS 485 ee ma RS 232 mim 7 Adresse esclave AAA 15 mu 9600 lu 4800 Vitesse n 1200 m 19200 e Re tighten the cover N B the role of the other micro switches is given in annexe B p13 BALOGH SA 189 rue d Auberviliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification Ref UM PRG 2660 V1 3 EN 3 2 5 CONFIGURING THE SERIAL PORT OF THE PC AND THE NETWORK Launch the PRGWINS2 software Select the Setup Port button Select the serial port Select the transmission speed previously set Enter the ad
7. code incremented the application offers as a code the code of the previous tag increased by 1 At the same time a prefix and or suffix as well as the hexadecimal format can be specified N B if the three boxes are checked the serial n S N is also automatically incremented upon each programming Automatic incrementation accelerates and increases the reliability fewer data entry errors of the programming of tags belonging to the same batch same format same mode codes and possibly serial n which follow on from each other p 6 BALOGH SA 189 rue d Aubervilliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification R f UM PRG 2660 V1 3 EN Configuration phase Enable Issuer Code Password o i Load Format mf x Format Mode Ge ASCII Ge Normal C1502 fast C WIEGAND 6 power down C WIEGAND 32 Cancel EI Programming Box Status Issuer Code Mame Format ASCII Mode POWERDOYN B Database file e keyboard code verfu serial number show last code Setup Port About i Setup Port EN nd Serial Fart Baud rate COM S600 COM3 4500 COM4 1200 Address Prog Bas m Address Header Cancel p7 BALOGH SA 189 rue d Aubervilliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification R f UM PRG 2660 V1 3 EN Modifying the configuration selection of the database or the file is done via the Browse button th
8. dress of the two JBus slaves programming box and reader and confirm If the buttons in the application remain dimmed check the configuration of the programming box 3 2 6 CONFIGURING THE PRGWIN32 APPLICATION Confirm the Programming Box Status text zone displays the code and the name of the integrator as well as the tag code format and tag mode last used In order to modify specify these parameters Power up the converter and the programming box Select the button Enable Issuer and enter the password 4 characters with which Balogh has provided you Confirm OK the text zone displays the code and the name of the integrator Select the Load Format button to specify the code format and the mode of the tags to be programmed Confirm OK the Programming Box Status text zone in displays the tag code format and the tag mode N B the Wiegand 26 format includes a site code Facility Code which is displayed in the zone bis and which can be modified between 0 and 255 Choose via the radio buttons one of the three code supply possibilities extraction from a Microsoft database with an mdb extension Database extraction from a codes text file file entering it via the keyboard keyboard Check the option boxes if necessary serial number enter the tag serial number as well as its code show last code displays the previous code This option give
9. e current path an the line n for a database is displayed m PRG WwIN32 Programming Box Status Issuer Code 228 Mame ASYA Program Code Format ASCII Mode NORMAL Enable ssuer Hu Load Format CG Data base t fle C Program Filess amp dobe aoLree 6 0 FRAME keyboard Browse Line Number Head Tags code verify serial number Change Mode EI Exit Setup Fort Abnut To change the prefix the suffix or the decimal hex format uncheck and re check the show last code and code incremented boxes When you exit the application Exit button the configuration is saved and automatically remembered at the next session N B the prefixes and or suffixes are not saved p 8 BALOGH SA 189 rue d Auberviliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification R f UM PRG 2660 V1 3 EN 2 2 IMPLEMENTATION Insert the flat tag BDG 1020 or adaptation tag for BDG 1090 see annexe 2 with the golden connector at the top into the slot on the programming box until it makes contact the Programming Box Status text zone square becomes red Select the Program Code button enter the tag code and confirm If the serial number box has been checked the tag serial number is also requested Select the Change mode button to change only the mode of the tag connected This modifies the current mode displayed in ic PRGWIN32 B x PRG v3 01
10. er p 16 BALOGH SA 189 rue d Auberviliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification R f UM PRG 2660 V1 3 EN 4 ERROR MESSAGES Connection failed serial port occupied check the applications which access the port Password invalid check and re enter the password used Code too long check file code is too long it must not exceed 29 characters Specific limits Alohanumeric ISO 2 29 characters Wiegand 26 number lt 65 536 Invalid input incorrect data entry Input out of bounds data is outside the required format authorized characters figures capital letters punctuation symbols the ASCII code of which is between 20h and 5Fh excluding Insert tag the tag must be connected inserted to be able to use the Change Mode button Reader not found the LPR reader has not been detected check its configuration No tag read the tag has not been presented to the reader in time Bad code programming fault reprogram the tag p 17 BALOGH SA 189 rue d Aubervilliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification R f UM PRG 2660 V1 3 EN ANNEXE 1 CONFIGURATION OF THE PROGRAMMING BOX Mode Address Www J3 kannn J4 769432 Brea 244321 confirmed 1 BEEPER mB cont HIE m inhibited mimi impr mja RS 422 SLAVE ADDRESS INTERFACE le RS 485 nja RS 232 TEE SPEED z Oe 3800 TRANSM EI normal online programmin
11. g RU 1200 SPEED OPERATING le test mode pg normal tag every s mm 1920 MODE AR test mode ditto Al code de test pg 20 characters every s Default configuration beeper confirmed interface RS 232 normal speed normal mode address 1 p 18 BALOGH SA 189 rue d Auberviliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification R f UM PRG 2660 V1 3 EN ANNEXE 2 BDG 1090 PROGRAMMING WITH ADAPTER The jack is to be plugged into the BDG 1090 connector as indicated below d e i Ww BALOGH SA 189 rue d Auberviliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification Ref UM PRG 2660 V1 3 EN p 19
12. lt 19 200 bauds N B the addresses of the programming box and the reader are ineffective in point to point programming without verification If the application s buttons remain dimmed check the configuration of the programming box 2 1 2 CONFIGURATION OF THE PRGWIN32 APPLICATION Supply the programming box with power The diagram on the following page summarizes the successive operation of the configuration phase Select the button Enable Issuer and enter the password 4 characters with which Balogh has provided you Confirm OK the text zone O displays the code and the name of the integrator Select the button Load Format to specify the code format and the mode of the tags to be programmed Confirm OK the text zone Programming Box Status in displays the tag code format and the tag mode N B the Wiegand 26 format includes a site code Facility Code which is displayed in zone bis and may be modified between 0 and 255 Select via the radio buttons one of the three code supply possibilities extraction from a Microsoft database with an mdb Data base extension extraction from a codes text file file entering it via the keyboard keyboard Check the option boxes if necessary serial number enter the tag serial number as well as its code show last code displays the previous code This option gives access to an self incrementing sub option
13. rogrammer casing is a JBus peripheral capable of encoding a tag by contact The front elevation contains a slot for the insertion of a flat tag BDG 1020 or mechanical adaptation tag for BDG 1090 and a power on indicator light The box is supplied with 12 Vdc 8 15 Vdc via a 2 1mm jack on the rear elevation via the power supply It communicates with the PC in point to point via a Sub D9 connector and in multipoint via a 5 pin teminal block power jack terminal Sub D9 connector block If the programming box is the only peripheral connected to the PC s serial port communication is in point to point this is the assumption made in what follows for configuring the port in terms of programming only Also the box is configured by default in RS 232 and with a speed of 19 200 bauds For programming with verification by a Hyper X reader communication is in multipoint 1 2 INSTALLATION AND CONNECTIONS Install the PRGWIN 32 software on the PC from the installation CD ROM Connect the power supply and the PC Sub D9 connector to the programming box as indicated in the photograph above p 5 BALOGH SA 189 rue d Aubervilliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification R f UM PRG 2660 V1 3 EN 2 PROGRAMMING 2 1 CONFIGURATION 2 1 1 CONFIGURING THE PC S SERIAL PORT Launch the PRGWIN32 software Select the button Setup Port Select the serial port Select the transmission speed defau
14. s access to a self incrementation sub option code incremented the application proposes as a tag code that of the previous tag increased by 1 At the same time a prefix and or suffix as well as the hexadecimal format can be specified N B if all three boxes are checked the serial n S N is also incremented automatically upon each programming Automatic incrementation accelerates and increases the reliability fewer data entry errors of the programming of tags belonging to the same batch same format same mode codes and possibly serial n which follow on from each other Check the code verify box to enable automatic verification of the tag codes p 14 BALOGH SA 189 rue d Aubervilliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification R f UM PRG 2660 V1 3 EN 3 3 IMPLEMENTATION Insert the flat tag BDG 1020 or adaptation tag for BDG 1090 see annexe 2 with the golden connector into the slot on the programming box until it makes contact the Programming Box Status text zone Square becomes red Select the Program Code button enter the tag code and confirm The message Checking Reader followed by the code is displayed in red in the Display Messages zone for as long as the tag is presented in front of the reader The pop up message Bad code indicates a programming fault Select the Change mode button to change only the mode of the tag connected This modifies
15. the current mode displayed in w PRGWIN32 Fragramming Box Status Issuer Code 228 Mame ASE Format ASCII Mode NORMAL Enable Issuer sinon Checking laces 25123123 Load Format C Data base C file keyboard Change Mode Read Tags M code verify serial number show last code lt EH E xil Setup Port About N B refer to paragraph 2 2 for the example given there the text file records verif column the results of the code read instruction comparison p 15 BALOGH SA 189 rue d Auberviliers C P 97 75886 PARIS Cedex 18 FRANCE subject to modification R f UM PRG 2660 V1 3 EN 3 4 SIMPLE READING The Read Tags button allows the tag to be read independently of the programming box the application serving only as a human reader interface A List Tags window appears the codes of tags successively presented to the reader are displayed ree eee nae teres PRG 3 01 Programming Bas Status Issuer Code 228 Mame AS VA Program Code Format ASCII Mode NOAMAL Hu Enable Issuer Load Format Data base C file Change Mode Ce keuboard Read Tags code verify serial number EI Exil Setup Port About im List Tags Of x Header Address 2 M Format simple N B the checkbox Format simple displays the code without a header the filtering of integration codes depends on the configuration of the read
Download Pdf Manuals
Related Search