PetSafe® Deluxe In-Ground Cat Fence™
Contents
1. e In an area where temperatures do not fall below freezing e g garage basement shed e Secured to a stationary surface using appropriate mounting hardware not included A mounting template is included on the back of this guide e At least 3 feet from large metal objects or appliances as these items may interfere with the signal consistency 1C Once you have mounted the Fence Transmitter the Boundary Wire must exit the building This can be accomplished via a window or through a s in hole drilled through the wall Ensure the drill path is clear of any utilities Make sure the Boundary Wire is not cut off or pinched by a window door or garage door as this can damage it over time To prevent fires and electrical hazards install the Fence Transmitter in buildings that are in accordance with state and local electrical codes Lay Out the System Basic Planning Tips e When planning your layout take care to exclude access to trees sheds or other items your cat can use to jump over the Boundary The signal from the Boundary Wire only extends the same distance vertically as horizontally If your cat can take the Receiver Collar out of reach of the signal he can jump the Boundary without receiving a Static Correction e The Boundary Wire MUST start at the Fence Transmitter and make a continuous loop back 2A e Design a layout that is suitable for your yard Sample layouts are provided in this section and a grid f2. Days 1 thru 2 Boundary Awareness Warning Zone Perform three or four training sessions per day each lasting 10 15 minutes Important e Your cat MUST stay in a harness for training to allow for any unpredictable response The harness also gives you control to guide your cat to a place of safety within the Pet Area once warned or corrected by the Receiver Collar If your cat attempts to leave the Pet Area make sure he does not get past the Boundary Flags Never let the cat past the Boundary Flags with or without the Receiver Collar on If your cat thinks he can pass the Boundary Flags training will take longer Goal To teach your cat to associate the beep with the position of the Warning Zone Steps Set the Receiver Collar to Level 1 tone only Put the harness and lead on your cat Lead him into the Pet Area and up to a chosen point by the Boundary Flags Holding the Receiver Collar near your cat s ears lead him into the Warning Zone As the beep sounds urgently say run away run away while pulling your cat on the harness into the Pet Area Praise and give affection to your cat 5 Connect the response to the beep with the Boundary Flag response by carrying a spare Boundary Flag Produce the Boundary Flag and wave it at the point the Receiver Collar starts to beep 6 Repeat the process at several different Boundary Flags 7 As you repeatedly lead your cat to the Boundary Flags and the warn
3. calm and respectful manner Gain your cat s trust and you will build a mutual respect which will ultimately lead to success It must be remembered that by their very nature cats are more agile and therefore more mobile than dogs You must be very aware of your training environment If it is possible for your cat to climb on a shed or up a tree taking the Receiver Collar out of reach of the signal from the Boundary Wire then it is possible that he could jump the Boundary without receiving a Static Correction The time scale for fully training your cat can range from one to two weeks During the training period you should be able to detect from your cat s response if it is time to move on to the next training phase Receiver Collar Familiarity Goal To familiarize your cat with the Receiver Collar if he has not worn one before Steps 1 Fit the Receiver Collar as detailed in Step 9 of this guide but without batteries inserted so there is no chance of your cat receiving a correction at this early stage 2 Reward your cat for allowing you to put on the Receiver Collar and leave him for a short period of time 5 15 minutes Gradually increase the time your cat spends wearing the Receiver Collar to an hour or more 3 Your cat is ready to move on to Phase 1 when you observe him behaving normally e g grooming eating sleeping showing affection while wearing the Receiver Collar 1 800 732 2677 Training Guide On Lead Method
4. Test Light indicate that the Receiver Collar and the system are working properly and that you are ready to start burying the Boundary Wire If the Receiver Collar did not beep or the Test Light did not flash see the Troubleshooting section Note The Boundary Width is broken down into 20 Warning Zone and 80 Static Correction Zone 1 800 732 2677 Install the Boundary Wire To Bury the Boundary Wire Burying the Boundary Wire is recommended to protect it and prevent disabling the system 1 Cut a trench 1 to 3 inches deep along your planned boundary 2 Place the Boundary Wire into the trench maintaining some slack to allow it to expand and contract with temperature variations 3 Use a blunt tool such as a wooden paint stick to push the Boundary Wire into the trench Be careful not to damage the Boundary Wire To Attach the Boundary Wire to an Existing Fence The Boundary Wire of the PetSafe Deluxe In Ground Cat Fence can be attached to a chain link fence split rail fence or a wooden privacy fence The Boundary Wire can be attached as high as needed However make sure the Boundary Width is set at a high enough range for your cat to receive the signal If using a Double Loop with an existing fence at least 3 feet tall run the Boundary Wire on top of the fence and return it on the bottom of the fence to get the 5 foot separation needed e Chain Link Fence 7A Weave Boundary Wire through the links or use plastic quick
5. area safely Plastic or metal piping will not cancel the signal Twist the Boundary Wire 10 12 times per foot to cancel the signal The maximum length of twisted wire is 50 feet To Splice or Repair the Boundary Wire 3B If you need additional Boundary Wire to expand your wire loop you will need to splice the wires together Note the locations of all splices for future reference Most Boundary Wire breaks occur at splices Strip approximately 1 2 in of insulation off the ends of the Boundary Wires to be spliced Make sure the copper Boundary Wire is not corroded If the Boundary Wire is corroded cut it back to expose clean copper wire Insert the stripped ends into the wire nut and twist the wire nut around the wires Pull on the wires to make sure you have a strong splice connection Apply waterproofing compound e g silicone caulk in and around the wire nut or wrap the wires and the wire nuts with electrical tape to prevent moisture from corroding the copper If your splice pulls loose the entire system will fail Make sure your splice is secure 1 2 1 2 EEEE EEEE A www petsafe net 7 Additional Boundary Wire We recommend the use of 20 gauge insulated multi strand copper wire for direct burial Extra Boundary Wire can be purchased in 500 ft spools at the store where you purchased the kit or through the Customer Care Center at 1 800 732 2677 Note When adding Boundary Wire it must act as a continuous loop The table
6. at right indicates the approximate length of Boundary Wire needed for a rectangular Single Loop layout Length will vary due to the amount of twisted wire and layout used Remember that a double loop will require twice as much wire Boundary Wire 4A 1 Run the Boundary Wire to the Fence Transmitter through a window under a door through a crawl space vent or any other appropriate available access You can also drill a hole through your wall 2 Strip the ends of the Boundary Wire approximately 1 in 3 Insert the Boundary Wires into the Boundary Wire Terminals on the Fence Transmitter 4 Turn the Boundary Width Control knob to 10 This will set the Warning Zone at the maximum width 5 Plug the Power Adapter into the Power Jack and a 120 volt outlet rs mnan 6 The Power Light and Loop Indicator Lights should come on If this does not Tehi Power Light 3 33 happen see the Troubleshooting section Boundary Width Control Ground Wire 4B Proper grounding although not necessary for the system to work will help reduce the chance of electrical surges causing damage to your Fence Transmitter and or Power Adapter To ground your unit you will need a solid not stranded Ground Wire 14 to 18 gauge insulated copper wire and a ground rod with clamp which may be obtained at most electrical supply stores Connect one end of the Ground Wire to the Ground Terminal located on the Fence Transmitter and the other end of t
7. of your layout and keep your cat from jumping out or digging under your existing fence It reduces the amount of wire which will need to be buried From the Fence Transmitter run the wire to A A to B B to C C to D D to E E to A twist the wires from A back to the Fence Transmitter See the Install the Boundary Wire section for more information on attaching the wire to a fence A Double Loop must be used when you are not establishing the Boundary Zone on all sides of your property When using a Double Loop the Boundary Wire must be separated by a minimum of 3TO 5 FEET to avoid canceling the signal Remember that a Double Loop will require twice as much wire Sample 3 2F Front or Back Yard Only Double Loop From the Fence Transmitter run the wire to A A to B B to C C to D D to E E to F make a U turn and follow your path all the way back to A keeping the wire separated 3 to 5 feet Twist the wire from A back to the Fence Transmitter Sample 4 2G Front Boundary Only Double Loop From the Fence Transmitter run the wire to A A to B B back to A keeping the wire separated 3 to 5 feet Twist the wire from A back to the Fence Transmitter 1 800 732 2677 Sample 5 2H Lake Access Double Loop From the Fence Transmitter run the wire to A A to B make a U turn and go to C C to D D to E make a U turn and follow your path all the way back to A keeping wire separated 3 to 5 feet Twist
8. with this Product We recommend that you not use this Product if your pet is less than 6 lbs or if your pet is aggressive If you are unsure whether this is appropriate for your pet please consult your veterinarian or certified trainer Proper use includes reviewing the entire Guide provided with your Product and any specific Caution statements 3 No Unlawful or Prohibited Use This Product is designed for use with pets only This pet training device is not intended to harm injure or provoke Using this Product in a way that is not intended could result in violation of Federal State or local laws 4 Limitation of Liability In no event shall Radio Systems Corporation be liable for any direct indirect punitive incidental special or consequential damages or any damages whatsoever arising out of or connected with the use or misuse of this Product Buyer assumes all risks and liability from the use of this Product 5 Modification of Terms and Conditions Radio Systems Corporation reserves the right to change the terms conditions and notices under which this Product is offered FCC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment This equipment generates uses and can radiate radio frequency energy and if
9. DE Memon reais ea nana TH a aU E Eine E pean CEE ee caine trate EE 20 P rod ct Warranty oreren ne peeedad sind nrn r E E aa E E a E E EEI i 21 Layout Grid eea R ea ear eo E ea ae ead E E EEE 22 Mo nt ne Template erroreren a e e E EEE E TEOS aaa 24 2 1 800 732 2677 Components Boundary Wire Boundary Flags 50 Battery PetSafe RFA 188 Receiver Wire Nuts Installation and Training Operating and Test Light Tool DVD Training Guide Other Items You May Need e Additional wire and flags Part PRFA 500 e Electrical tape e Tape measure e Additional wire nuts e Drill amp mounting hardware e Waterproofing compound e g silicone caulk e Shovel or lawn edger e PVC pipe or water hose e Pliers e Circular saw with masonry blade e Wire stripping pliers e Patching compound e Scissors e Staple gun e Lighter e Non metallic harness and lead Training Equipment Needed e Harness sized to fit your cat e 15 20 screw in tie out Required for supervised tie out training On lead training does not require tie out Note For information on professional installation of your new PetSafe Deluxe In Ground Cat Fence contact the Customer Care Center at 1 800 732 2677 or visit our website at www petsafepro com www petsafe net 3 How the System Works The PetSafe Deluxe In Ground Cat Fence has been proven safe comfortable and effective for all cats over 6 lb and at least 6 months old The system works by prod
10. PetSafe Deluxe In Ground Cat Fence Operating and Training Guide Please read this entire guide before installation Thank you for choosing PetSafe the best selling brand of electronic training solutions in the world Our mission is to be the most trusted brand in the pet ownership experience We want to ensure your pet s safety by providing you with the tools and techniques to successfully train your pet If you have any questions please contact the Customer Care Center at 1 800 732 2677 or visit our website at www petsafe net To get the most protection out of your limited warranty please register your product within 90 days at www petsafe net By registering you will enjoy the product s full warranty and should you ever need to call the Customer Care Center we will be able to help you faster Additionally you will not have to save your product receipt as registering serves as proof of purchase Most importantly PetSafe will never give or sell your valuable information to anyone Table of Contents ROA GIS ge pp pss cscewne tenascin oad tas ad ad ena a ap saan E E a eee taganiaoiee 3 Other Items You May Nedrema eE Eie E Ea E SE E Ea nE Ena 3 How the System WS eee a e E E EE E R 4 Key D NNIONS ssreeise sepana enterro eaa oae e ee oiea eepe e iea e EEE E 4 Operating Guide Locate the Fence LransSimiitter oeeie nre AE a EE E EE TEE EE aE oE EEEn 5 Ty OG ay 1 a 0 E AE TE E EEE TA 5 Sample Layou lsrs er E E EE EE Ge eee 6
11. Position the Boundary Wire ncsnenenee n a N nes 7 Connect the Wires to the Fence Transmitter sessssrreirerrii res setii tenentis ERAL E EEE ENE S EPESA EE ETES ETET 8 Prepare the Receiver Collais r E a E E a 9 F cton and Response Table sretnes a a ae aa e ern ae a 9 Set the Boundary Width and Test the Receiver Collars csiccags coisa pantsacganenhcegcenhtdocsnteassannuncepeiseivadis 10 Install the Boundary Wy 18a seninsactaciens n EE a rE EEE 11 Place the Boundary Flags inene E E E E E EE 12 Fit he Receiver Collatie araser eer E E E E OEE EEREN 12 Training Guide Be Patent With Your Cat eemerseres iorri nerean E esea E E EE E E A EEEE AEE EEEE ES 14 ge 0 2 000 0 ee PP a e a ae a e a er EE nent rere eer ree 14 theceiver Collar Familiarity sccicsadcos lca cecvnaceagieubeecebaedeebaciau eii ee ea e erate e iiei 14 On Lead Training Memhod priserne a a a a E E E E E a 15 Supervised Tie Out Training Method ereus ioe rnerne a reae E Ena ae E AEE EP TESTE 17 ACCESSOS e E a Caan a a nai none nonateaeeee eee temens 17 Troubleshooting soree a placa E E E E R EOE E EOE 18 S ate aA esa ol lt 1 E EE E A reer EE E E OE AE E E A eer nr ener emer 19 To Locate a Break in the Boundary Wite ces ede iketcccacasaseiieshnesaepahieeipeexecd is an ean EIE ea eee 19 Terms of Use and Limitation of Liability csc is csp esa cinntepmedaroea pane dare pana E E R EE 20 FCC roren ar sw bw ptt re a tnt me a E ee anc ba wane aa 20 Cattoi a cresce cred Ses mince E use aula us
12. at 5 If your cat ignores the Static Correction first check the Receiver Collar fit to ensure good contact with the skin and try again If he still ignores the correction try gradually increasing the Correction Level as detailed in Step 5 of this manual until he reacts 6 This should complete the association with the need to move away from the Boundary If your cat has responded well to the previous steps it should not be necessary to purposefully make your cat experience a Static Correction more than once or twice Days 8 thru 14 Unleashed Observation Training sessions should start at 10 15 minutes gradually increasing to one hour and more Your cat is ready for this phase only when he normally avoids the Boundary Flag line During this phase watch your cat carefully Goal To give your cat free run of the Pet Area Steps 1 Fit the Receiver Collar as detailed in Step 9 of this guide 2 Allow your cat freedom in your property while you act as a minder 3 Observe your cat as he approaches the Boundary and receives warning beeps and Static Corrections on his own If he responds by turning away from the Boundary and is not distressed your cat is ready to move on to the final Phase Days 15 thru 30 Extended Observation For the first few weeks after training check on your cat regularly to ensure that all is well Gradually reduce your checking until both of you have total freedom After you are satisfied your cat s tra
13. be used with healthy pets Contact your veterinarian if you have concerns about the medical condition of your pet medication pregnant heart conditions etc e This system is not for vicious or aggressive pets If your pet may pose a threat to others DO NOT USE THIS SYSTEM If you are unsure if your pet is aggressive please consult your veterinarian or a certified trainer e The PetSafe Deluxe In Ground Cat Fence is for residential use only e The Static Correction will get your pet s attention but will not cause harm It is designed to startle not to punish e Test the Receiver Collar every 2 months Battery life depends upon how often the Receiver Collar is activated Short Loop Test The Short Loop Test is a simple test to determine if each component Fence Transmitter Receiver Collar and Boundary Wire is functioning properly 1 Disconnect the Boundary Wire and Ground Wire 2 Cut approximately 10 feet of unused Boundary Wire and connect it to the Boundary Wire Terminals 3 Attach the Test Light to the Receiver Collar 4 Spread the Boundary Wire out into a circle Set the Boundary Control Switch to B 5 Set the Boundary Width Control knob to 10 and the Static Correction Level to 2 or above 6 If the Loop Indicator Light is not lit then your Fence Transmitter is not functioning properly Contact the Customer Care Center at 1 800 732 2677 7 If the Loop Indicator Light is lit disconnect one end of the Boundary Wire fro
14. ceiver Collar batteries are properly installed the Static Correction Level is set at 2 or above and the Test Light Contacts are held to the Contact Points 6C Walk toward the Boundary Wire holding the Receiver Collar at your cat s neck level 6D until the Receiver Collar beeps 6E Note The Receiver Collar is waterproof which can make the beep hard to hear If the Receiver Collar does not beep at the desired range adjust the Boundary Width Control knob to the desired setting Turning the Boundary Width Control knob clockwise increases the Boundary Width while turning it counterclockwise decreases it 6B Repeat this activity as needed until the Receiver Collar beeps at the desired distance from the Boundary Wire The numbers on the Boundary Width Control knob indicate signal strength and are not representative of Boundary Width footage If adjusting the Boundary Width Control knob does not give the desired range adjust the Boundary Control Switch to another setting to achieve your desired range If using a Double Loop you may need to increase the separation of the Boundary Wire to achieve desired range The Receiver Collar beeps as a warning tone and ticks when delivering a Static Correction After hearing the beep continue to walk towards the wire The Receiver Collar should tick and the Test Light should flash indicating the Static Correction as you enter the Static Correction Zone 6E A warning tone and the flashing of the
15. e Drill Here 3 000 7 62 cm Drill Here Radio Systems Corporation 10427 Electric Avenue Knoxville TN 37932 1 800 732 2677 www petsafe net 400 844 Covered by US Patent 6 921 089 other patents pending Copyright 2007 Radio Systems Corporation
16. ferent areas of the Boundary 6 Continue the training for 3 days During this period your cat will learn to recognize the warning beep and to avoid the Static Correction Zone Supervise your pet in the yard for several weeks Leave the Boundary Flags in place for 3 weeks after your cat is trained Then remove every other Boundary Flag every 4 days until they are all gone Keep the Boundary Flags for future use Regularly check the Receiver Collar and the fit against your cat s skin Accessories To purchase additional accessories for your PetSafe Deluxe In Ground Cat Fence contact the Customer Care Center at 1 800 732 2677 Some of the accessories may also be purchased at a retail store Visit www petsafe net to find a retailer near you Only available through the Customer Care Center www petsafe net 17 Troubleshooting Receiver Collar is not beeping or correcting e Check battery to make sure it is installed properly e Check that both lights are lit on the Fence Transmitter If not perform the Short Loop Test The Receiver Collar is beeping but my cat is not responding to the Static Correction e Make sure that Static Correction Level is at 2 or above e Test the Receiver Collar with the Test Light If the Test Light flashes check the fit of the Receiver Collar e Trim your cat s fur where the Contact Points touch the neck e Increase the Static Correction Level e Repeat training steps
17. he Ground Wire to the ground rod The ground rod must be buried at least three feet into the ground and located as close as possible to the Fence Transmitter Fuse Protection 4C The Fence Transmitter is also equipped with a 250 volt 2 amp fuse to protect the unit s electronic circuitry from electrical power surges To locate the fuse slide off the lid on the back of the Fence Transmitter A spare fuse is also provided Spare Huse Lightning Protection You may purchase a Lightning Protection Kit through the Customer Care Center at 1 800 732 2677 The Lightning Protection Kit protects the system against surges that travel through the power source and or the Boundary Wire If you use a Lightning Protection Kit the Ground Wire must be removed from the Fence Transmitter The Lightning Protection Kit utilizes a ground connection separate from the Fence Transmitter 1 800 732 2677 Prepare the Receiver Collar To Insert and Remove the Battery Note Do not install the battery while the Receiver Collar 1s on your pet This Receiver Collar utilizes a replaceable PetSafe battery RFA 188 This unique battery is designed to make battery replacement easier and increase water protection To activate the collar insert the battery module 5A Using the edge of the Test Light Tool as shown turn the battery clockwise until the vertical line on the battery is pointed to the ON position 5B If the PetSafe Receiver Collar is not go
18. he training period Carefully read both methods to determine which is right for you and your cat Be Patient With Your Cat Important Proper training of your cat is essential to the success of the PetSafe Deluxe In Ground Cat Fence Read this section completely before beginning to train your cat Remember that the PetSafe Deluxe In Ground Cat Fence is not a solid barrier Training should be fair firm and consistent e Train for 10 to 15 minutes at a time Don t try to do too much too quickly More frequent short sessions are better than less frequent longer sessions If your cat shows signs of stress slow down the training schedule and or add additional days of training e Finish each training session with lots of praise and affection e Remove the Receiver Collar after each training session e Keep your cat on a harness attached to a lead during training sessions e Even if you think your cat is responding well to the training complete the entire training Reinforcement is important e Regularly check the fit of the Receiver Collar against your cat s skin Preparation Your goal is to train your cat to turn away from the Boundary Zone every time he hears the warning beep from the Receiver Collar During training your cat must develop an understanding of the Boundary and that you require him to remain within it Cats are independent creatures In order to gain the correct response you must always work with a kind
19. ing beep sounds you should notice some reluctance from him and he should try to move away Bone Days 3 thru 7 Boundary Awareness Static Correction Zone Perform three or four training sessions per day each lasting 10 15 minutes Important e Your cat MUST stay in a harness for training to allow for any unpredictable response The harness also gives you control to guide your cat to a place of safety within the Pet Area once warned or corrected by the Receiver Collar If your cat attempts to leave the Pet Area make sure he does not get past the Boundary Flags Never let the cat past the Boundary Flags with or without the Receiver Collar on If your cat thinks he can pass the Boundary Flags training will take longer Goal To teach your cat to associate the Static Correction with the position of the Static Correction Zone Steps 1 Set the Receiver Collar to Level 2 the lowest Static Correction level 2 Fit the Receiver Collar as detailed in Step 9 of this guide 3 As in Phase 1 lead your cat to the Boundary Flags but let him move through the Warning Zone to receive the small Static Correction Note You may need to remove every other flag at this stage to encourage your cat to approach the Static Correction Zone www petsafe net 15 16 4 When your cat is corrected urgently say run away run away while pulling him into the Pet Area where the beep will stop Praise and give affection to your c
20. ing to be used on the cat immediately leave it in the OFF position To remove the battery turn the battery counter clockwise using the edge of the Test Light Tool as shown 5C 5D DO NOT attempt to cut into or pry open the battery Be sure to discard the used battery properly A replacement PetSafe battery can be found at many retailers Contact the Customer Care Center at 1 800 732 2677 or visit our website at www petsafe net to locate a retailer near you Two Color LED The two color LED indicator shows good or low battery Good battery equals 1 flash every 60 seconds with Green LED Low battery equals 3 flashes every 60 seconds with the Red LED If there are no LED lights it is time to change the battery To Set the Static Correction Level Read all steps before attempting to set the Static Correction Level 1 With the battery installed press the Correction Level Button and release when the Receiver Indicator Light lights red SE 2 The Receiver Indicator Light will emit a number of red flashes representing the Static Correction Level 5F 3 Increase the Static Correction Level by pressing and releasing the Correction Level Button within 5 seconds of the previous flashes The Static Correction Levels increase from 1 to 5 Pushing the Correction Level Button while the Receiver Collar is on level 5 will cause the Receiver Collar to revert to level 1 Refer to the Function and Response Table to choose the Static Correctio
21. ining is complete remove every other Boundary Flag every 4 days until all flags are removed Save Boundary Flags for future use If you need to take your cat out of the Pet Area remove the Receiver Collar and leave it in the Pet Area Congratulations You have now successfully completed the training program 1 800 732 2677 Training Guide Supervised Tie Out Method To train your cat to turn towards home every time he hears the warning beep from the Receiver Collar Training should take about one week Setup 1 When training a cat use a harness for attaching the tie out 2 Set the Receiver Collar to Correction Level 2 or 3 depending on the size and temperament of your cat The higher the Correction Level the stronger the Static Correction 3 Cats must wear Receiver Collars much tighter than standard collars Both Contact Points must touch the skin 4 Purchase a 15 to 20 yard tie out from any pet store Steps 1 Insert the yard anchor in the ground so the end of the tie out reaches 1 to 2 feet past the Warning Zone 2 To ensure your cat s well being be sure there is shade and fresh water within the radius of the tie out 3 Attach your cat s harness to the tie out 4 Leave your cat in the tie out area for 4 to 6 hours Supervision is required for your cat s safety Your supervision will monitor whether your cat has received a correction and whether your cat is learning the system 5 Move the tie out to dif
22. lp your situation The Power and Loop Indicator Lights are off e Check that the Power Adapter is plugged into the Fence Transmitter Try plugging into another 120 volt outlet e Remove the fuse door on the back of the Fence Transmitter and change out the fuse with the spare one located in the same area e If the lights still do not come on the Fence Transmitter and or Power Adapter needs to be replaced Contact the Customer Care Center at 1 800 732 2677 The Power Light is on the Loop Indicator Light is off and the Fence Transmitter loop alarm is sounding e Make sure both ends of the Boundary Wire are plugged into Boundary Wire Terminals and that 1 2 inch of the insulation is stripped so that the copper wire is exposed e Perform the Short Loop Test to determine if the Fence Transmitter needs to be replaced or if the Boundary Wire is broken If the Fence Transmitter is functioning properly you have a break in your Boundary Wire See the To Locate a Break in the Boundary Wire section in this guide The fuse blows when it is replaced e The Fence Transmitter and or Power Adapter needs to be replaced Contact the Customer Care Center at 1 800 732 2677 18 1 800 732 2677 Additional Information e The Boundary Wire is buried so that it is not accidentally tripped over or cut Use care when trimming grass or digging near the Boundary Wire to prevent damage e The system should only
23. m the Boundary Wire Terminal 8 If the loop alarm does not sound the Fence Transmitter needs to be replaced Contact the Customer Care Center at 1 800 732 2677 9 If the loop alarm does sound plug the Boundary Wire back into the Boundary Wire Terminal 10 Hold the Receiver Collar next to the 10 foot length of Boundary Wire The Receiver Collar should beep about 1 foot away from the Boundary Wire The Test Light should then flash as you hold the Receiver Collar closer to the Boundary Wire 11 If Receiver Collar does not beep and the Test Light does not flash replace the battery in the Receiver Collar If it still does not beep and the Test Light does not flash contact the Customer Care Center at 1 800 732 2677 12 If the Receiver Collar beeps there may be a complete or partial break in the Boundary Wire See the To Locate a Break in the Boundary Wire section To Locate a Break in the Boundary Wire Please follow these steps in determining where you have a break in your Boundary Wire 1 Locate your original splice s and verify they have a good solid connection 2 Check your yard to determine any possible damage to the Boundary Wire e g recent digging aerating rodent burrowing or any other noticeable disturbance in your yard next to the Boundary Wire If you still cannot find the break in the Boundary Wire follow the procedure below 1 Unplug the Fence Transmitter 2 Connect both ends of your twisted Boundary Wire to
24. move the Receiver Collar from your cat and cut off the excess c Before placing the Receiver Collar back onto your cat seal the edge of the cut collar by applying a flame along the frayed edge Important For comfort safety and effectiveness of product please ensure the following e During the first 2 weeks of training do not use the training device on your pet without direct supervision e Check the fit to prevent excessive pressure by being able to insert one finger between the Contact Point and your pet s skin e Your pet must be carefully examined daily for any signs of a rash or sore e If a rash or sore is observed discontinue the use of the Receiver Collar for a few days e If the condition persists beyond 48 hours see your veterinarian e Your pet s neck and the Contact Points must be washed weekly with a wash cloth and mild hand soap then rinsed thoroughly A condition called Pressure Necrosis which is a devitalization of the skin due to excessive and prolonged contact against the Contact Points may occur if the steps above are not followed To Re Thread the Collar Slide Buckle The slide buckle prevents the collar from becoming loose around your cat s neck www petsafe net 13 14 Training Guide Cat Training Introduction This training guide offers a choice of two training methods On Lead Method and Supervised Tie Out Method Both methods require close supervision of your cat throughout t
25. n level that best fits your pet The Receiver Collar is equipped to automatically increase the level of Static Correction the longer your pet remains in the Static Correction Zone if the collar is set at level 2 or above The Receiver Indicator Light acts as a low battery indicator flashing every 60 seconds when battery replacement is required Function and Response Table Note Begin training with Static Correction Level 2 and only increase if your pet does not respond to the Static Correction 1 Red Flash No Static Correction Tone Only 4 Red Flashes Medium High Static Correction Average or High Energy 5 Red Flashes High Static Correction High Energy Flashes 3 Red Flashes Low Battery every 60 seconds www petsafe net 9 10 Set the Boundary Width and Test the Receiver Collar The Boundary Control Switch on the side of the Fence Transmitter has three settings 6A Setting B is used for most properties The following table will indicate the setting you should use Fupto 1300 et s Use the Boundary Width Control knob to set the width of the Warning Zone and Static Correction Zone 6B Set the Boundary Width as wide as possible to give your cat the widest Warning and Static Correction Zones without reducing the Pet Area too much Note The Boundary Width Control knob does not change the Static Correction Level To identify the Warning and Static Correction Zones make sure the Re
26. not installed and used in accordance with the instruction guide may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a practical installation If this equipment causes harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Relocate the interfered receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different to that to which the receiver is connected e Contact the Customer Care Center at 1 800 732 2677 Unauthorized changes or modifications to the equipment not approved by Radio Systems Corporation could result in not meeting compliance with FCC regulations and could void the user s authority to operate the equipment Caution The PetSafe Deluxe In Ground Cat Fence is NOT a solid barrier The system is designed to act as a deterrent to remind pets by Static Correction to remain in the boundary established It is important that you reinforce training with your pet on a regular basis Since the tolerance level to Static Correction varies from pet to pet Radio Systems Corporation CANNOT guarantee that the system will in all cases keep a pet within the established boundary Not all pets can be trained to avoid crossing the bounda
27. ntil the Receiver Collar beeps 8A 3 Place a Boundary Flag in the ground 8B 4 Walk back into the Pet Area until the beeping stops 5 Repeat this process around the Warning Zone until it is marked with Boundary Flags every 10 feet or less Note If you cannot hear the beep see the Test Light Instructions in Step 6 Fit the Receiver Collar Important The proper fit and placement of your Receiver Collar is important for effective training The Contact Points must have direct contact with your cat s skin on the underside of his neck To assure a proper fit please follow these steps 1 Make sure that the batteries are not installed in the Receiver Collar 2 Start with your cat standing comfortably 9A 3 Center the Contact Points underneath your cat s neck touching the skin Note It is sometimes necessary to trim the hair around the Contact Points to make sure that contact 1s consistent 1 800 732 2677 4 Check the tightness of the Receiver Collar by inserting one finger between the end of a Contact Point and your cat s neck The fit should be snug but not constricting 9B 5 Allow your cat to wear the collar for several minutes then recheck the fit Check the fit again as your cat becomes more comfortable with the Receiver Collar 6 Trim the collar as follows 9C a Mark the desired length of the Receiver Collar with a pen Allow for growth if your cat is young or grows a thick winter coat b Re
28. one Boundary Wire Terminal 3 Measure and cut a Test Wire which is half the length of your total Boundary Wire footage 4 Connect one end of Test Wire to the other Boundary Wire Terminal 5 Locate the halfway point of your boundary and cut the Boundary Wire 6 Splice the other end of the Test Wire to either side of your Boundary Wire where you cut it in half 7 Plug in the Fence Transmitter and check the Loop Indicator Light If the Loop Indicator Light is on you can assume the break is in the other half of the Boundary Wire www petsafe net 19 8 If the Loop Indicator Light did not come on you may assume there is a break in this portion of the Boundary Wire However there is a small chance of having more than one break in your system Be sure to check both halves of your entire loop 9 Replace the damaged Boundary Wire with new Boundary Wire 10 Reconnect the Boundary Wire to the Fence Transmitter 11 Check the Loop Indicator Light If the Loop Indicator Light is on test the system with the Receiver Collar Terms of Use and Limitation of Liability 1 Terms of Use This Product is offered to you conditioned upon your acceptance without modification of the terms conditions and notices contained herein Usage of this Product implies acceptance of all such terms conditions and notices 2 Proper Use This Product is designed for use with pets where training is desired The specific temperament of your pet may not work
29. or Light The light that indicates the level of correction at which the Receiver Collar is set This light also serves as a low battery indicator Contact Points The contacts through which the Receiver Collar delivers the safe Static Correction when your cat moves into the Static Correction Zone Power Jack The jack where the Power Adapter plugs into the Fence Transmitter The Fence Transmitter is powered by a standard 120 volt outlet Boundary Control Switch The switch to adjust according to the length of Boundary Wire used Boundary Wire Terminals The terminals where the Boundary Wires connect to the Fence Transmitter in order to complete a continuous loop Loop Indicator Light The light that indicates that the Boundary Wire makes a complete loop enabling the signal to be transmitted Boundary Width Control The knob that adjusts the width of the Warning and Static Correction Zones Note Adjusting the knob does not change the level of Static Correction on the Receiver Collar Fence Transmit 0 Receiver Collar ter Fence Static Correction Transmitter Zone Correction Level Button x N Warning N Receiver Indicator Bottom Terminals Loop Indicator Light Power Light Boundary Width Control Boundary Width A Battery Module 1 800 732 2677 Operating Guide Locate the Fence Transmitter Place the Fence Transmitter In a dry well ventilated protected area 1A 1B
30. or designing your layout is provided in the back of this guide e Fence Planning Software is available online at www petsafe net fence After you have planned and saved your layout online contact our Customer Care Center to review and refine your layout e Twisting two sides of the Boundary Wire cancels the signal and allows your cat to cross over that area safely Plastic or metal piping will not cancel the signal Twist the Boundary Wire 10 to 12 times per foot to cancel the signal 2A e Always use gradual turns at the corners to produce a more consistent boundary 2B Do not use sharp turns as this will cause gaps in your boundary e Avoid making passageways too narrow for your cat to move about freely e g along the sides of a house e The Receiver Collar can be activated inside the house if the Boundary Wire runs along the outside wall of the house If this occurs remove your cat s Receiver Collar before bringing him inside decrease the range using the Boundary Width Control Knob or consider an alternative layout www petsafe net 5 Sample Layouts Double Loop Sample 1 Perimeter Loop Single Loop The Perimeter Loop is the most common layout This will allow your cat to freely and safely roam your entire property 2C It can also protect gardens pools and landscaping 2D Sample 2 2E Perimeter Loop Using Existing Fence Single Loop This layout allows you to include your existing fence as part
31. ry Therefore if you have reason to believe that your pet may pose a danger to others or harm himself if he is not kept from crossing the boundaries you should NOT rely solely upon the PetSafe Deluxe In Ground Cat Fence to confine your pet Radio Systems Corporation shall NOT be liable for any property damage economic loss or any consequential damages sustained as a result of any animal crossing the boundary 20 1 800 732 2677 Product Warranty Please register your product online at www petsafe net All parts are covered under warranty for the life of this product Labor is covered for the first year of ownership Thereafter there is a minimum service charge for the repair or replacement of the product Misuse loss damage by pet or improper use or handling is not covered PetSafe will not pay for loss of time inconvenience loss of use of your product or any incidental or consequential damage Warranty void if product resold Please contact the Customer Care Center at 1 800 732 2677 if you need service or for help in troubleshooting and if needed to arrange a repair for your product a service charge may apply Also please visit our website www petsafe net for Frequently Asked Questions and Troubleshooting Tips Perchlorate Battery Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate www petsafe net 21 Layout Grid 22 1 800 732 2677 www petsafe net 23 Mounting Templat
32. the wire from A back to the Fence Transmitter Sample 6 2J Wire Loop Attached to Existing Fence Double Loop This layout allows you to include your existing fence as part of your layout and keep your cat from jumping out or digging under your existing fence It reduces the amount of wire which will need to be buried Run the wire from the Fence Transmitter to A A to B B to C C to D D to E E to F make a U turn and follow your path all the way back to A keeping the wire separated 3 to 5 feet Twist the wire from A back to the Fence Transmitter See the Install the Boundary Wire section for more information on attaching the wire to a fence Position the Boundary Wire Lay out the Boundary Wire using your planned boundary and test the system BEFORE burying the wire or attaching it to an existing fence This will make any layout changes easier Running the Boundary Wire parallel to and within 5 feet of electrical wires neighboring containment systems telephone wires television or antenna cables or satellite dishes may cause an inconsistent signal If you must cross any of these do so at 90 degree angles perpendicularly If separating your Boundary Wire by at least 5 feet from a neighboring containment system s wire does not reduce the inconsistent signal contact the Customer Care Center at 1 800 732 2677 To Twist the Boundary Wire 3A Twisting the Boundary Wire cancels the signal and allows your cat to cross over that
33. ties e Wooden Split Rail or Privacy Fence 7A Use staples to attach Boundary Wire Avoid puncturing the insulation of the Boundary Wire e Double Loop with an Existing Fence Run the Boundary Wire on top of the fence and return it on the bottom of the fence to get the 3 to 5 foot separation needed e Gate Single Loop 7B Bury the Boundary Wire in the ground across the gate opening Note The signal is still active across gate Your cat cannot pass through an open gate e Gate Double Loop 7B Bury both Boundary Wires across the gate opening while keeping them 3 to 5 feet apart WEAVE WIRE INTO FENCE STAPLE WIRE TO FENCE TT A ae STAPLE WIRE TO FENCE DOUBLE LOOP www petsafe net 11 12 To Cross Hard Surfaces driveways sidewalks etc e Concrete Driveway or Sidewalk 7C Place the Boundary Wire in a convenient expansion joint or create a groove using a circular saw and masonry blade Place the Boundary Wire in the groove and cover with an appropriate patching compound For best results brush away dirt or other debris before patching e Gravel or Dirt Driveway 7D Place the Boundary Wire in a PVC pipe or water hose to protect the Boundary Wire before burying Place the Boundary Flags The Boundary Flags are visual reminders for your cat of where the Warning Zone is located 1 Hold the Receiver Collar at your cat s neck height 2 Walk towards the Warning Zone u
34. to reinforce training The Receiver Collar has to be held on top of the Boundary Wire to activate e Replace battery e Adjust Boundary Width Control knob clockwise to increase the distance from the Boundary Wire that the Receiver Collar activates You can also adjust the Boundary Control Switch to another setting e If using a Double Loop make sure Boundary Wires are separated 3 to 5 feet If the Receiver Collar still has to be held on top of the Boundary Wire perform the Short Loop Test The Receiver Collar activates inside the house e Turn the Boundary Width Control knob counterclockwise to decrease the distance from the Boundary Wire that the Receiver Collar activates e Make sure the Boundary Wire is not running too close to the house The signal can transmit through the walls of your house e Make sure Boundary Wires are twisted from Boundary to the Fence Transmitter I have an inconsistent signal e Make sure the Fence Transmitter is at least 3 feet from large metal objects or appliances e Make sure all Boundary Wire turns are gradual e Make sure the Boundary Wire is not running parallel to and within 5 feet of electrical wires neighboring containment systems telephone wires television or antenna cables or satellite dishes If a neighboring containment system may be causing an inconsistent signal contact the Customer Care Center at 1 800 732 2677 to see if a different frequency system will he
35. ucing a radio signal from the Fence Transmitter through up to 4000 ft of Boundary Wire The Boundary Wire is buried or attached to a fixed object to enclose the Pet Area You temporarily define this Pet Area with Boundary Flags for a visual aid in training your cat Your cat wears a Receiver Collar with Contact Points that touch his neck and once trained is allowed to roam freely in the Pet Area When your cat reaches the Warning Zone the Receiver Collar gives a warning beep If your cat continues into the Static Correction Zone a safe Static Correction will be delivered through the Contact Points to get his attention until he returns to the Pet Area Key Definitions Fence Transmitter The device that transmits the radio signal through the Boundary Wire Pet Area The area within the Warning Zone where your cat can roam freely Warning Zone The outer edge of the Pet Area where your cat s Receiver Collar begins to beep warning him not to go into the Static Correction Zone Static Correction Zone The zone beyond the Warning Zone where your cat s Receiver Collar will emit a Static Correction signaling him to return to the Pet Area Boundary Width The combination of the Warning Zone and the Static Correction Zone Receiver Collar The device that receives the radio signal from the Boundary Wire Correction Level Button The button to adjust the level of Static Correction your cat receives in the Static Correction Zone Receiver Indicat
Download Pdf Manuals
Related Search