Preset 10 Architectural User Manual
Contents
1. Preset 10 will stop sending DMX By going off line many moving lights and dimming systems will detect the loss of DMX and begin their shut down routine Page 6 of 7 RECORDING PRESET CROSSFADE TIME A crossfade is a fade where the new preset levels entirely replace the previous levels Each of the ten presets can have its own unique crossfade time Crossfade times default to five seconds Note Crossfade times range from a minimum of 0 second to as maximum of 999 seconds 16 Min 39 Sec Crossfade times can not be set while the Preset 10 is locked out red LED is illuminated To enter a different crossfade time 1 Disconnect the Preset Ten from any DMX512 source 2 Press the button of the preset you wish to edit The GREEN preset indicator LED will illuminate 3 Using a small blunt object i e paper clip depress the TIME SETTING MODE recessed button located adjacent to the yellow LED indicator The green indicator LED adjacent to the preset you selected to edit and yellow time will now flash You will have ten seconds to set the crossfade time If you decide after depressing the TIME SETTING MODE button that you do not wish to make an edit simply wait 10 seconds or depress the TIME SETTING MODE button a second time No changes will have been made 4 Enter the time in seconds using the PRESET SELECT buttons Use PRESET SELECT button 10 OFF to enter a zero i e 120 seconds is entered by pressing PRESET SELECT button 1 follo2. 003 800 4 900 o05 OFFOo Page 3 of 7 PRESET 10 ARCHITECTURAL INSTALLATION WIRING INFORMATION Preset 10 Architectural is designed to use daisy chain wiring topology An alternative to the daisy chain topology is the star topology To create a star a bidirectional isolated splitter model BiDi8 is required Also note that a system may contain multiple power supplies when voltage drop becomes a concern Please give us a call if you have any questions 120VAC DMX512 INPUT CABLE 120 Ohm Data Cable 1 Belden 9829 or Equivalent 2 16 AWG Stranded Wires 120 Ohm Data Cable Belden 9829 or 3 Equivalent 4 2 2 16 AWG Stranded Wires 120 Ohm Data Cable 5 Belden 9829 or Equivalent POWER SUPPLY m2 o om MS OFF o o e COLOR FROM Shield Pin 1 White Blue 5 Pin XLR Plate Pin 2 Blue White zack Power Supply Shield TB1 1 White Blue TB1 2 Blue White PRE10 Master TB1 3 Black TB1 4 Red TB1 5 Shield TB1 1 White Blue PRE10 Slave TB1 2 Blue White TB1 3 TO PRE10 Master PRE10 Slave Dimmer Cabinet DIMMERS USE TB1 Common TB1 Data TB1 Data TB1 Supply TB1 Supply hot TB1 Common TB1 Data TB1 Data TB1 Supply TB1 Supply hot Common Data Data The voltage provided to the Preset 10 Architectural must be between 9 and 24 volts DC or 10 and 16 volts AC The Preset 10 Arch
3. DOUG FLEENOR DESIGN PRESET 10 ARCHITECTURAL OWNERS MANUAL Arroyo Grande CA 93420 805 481 9599 gt Serial 05C183 DOUG FLEENOR DESIGN PRODUCT DESCRIPTION The Preset 10 Architectural is a lighting control station capable of storing up to ten presets These presets are recorded by capturing the output of a DMX512 console Each preset can then be assigned a unique fade time from 0 to 999 seconds Presets are recalled by pressing one of the buttons Systems can be created by using one or more stations and a power supply The solid aluminum faceplate is designed to install over a standard single gang electrical box Connections to the Preset 10 Architectural are power 2 wires and DMX512 3 wires Power for the Preset 10 can be supplied from a variety of sources including a 10V class 2 doorbell transformer The Preset 10 Architectural system can work in conjunction with a lighting console automatically switching between preset and console control When the console generates DMX the Preset 10 Architectural goes off line The console then operates normally Upon loss of DMX from the console the Preset 10 Architectural either returns to its pervious preset or holds the last look jumper selectable The Preset 10 system also comes in a portable version model PRE10 P that acts as a backup station for any DMX512 lighting console or as a stand alone DMX512 preset console PRESET INDICATOR LED GREEN PRESET
4. G DMX512 CURRENTLY FADING FROM PREVIOUS PRESET RECORDING PRESETS In order to set the individual dimmer levels recorded to a preset the Preset 10 must be connected to a DMX512 source When less than 512 dimmer levels are received a level of 0 will be stored for all channels above those received Note For predictable results avoid recording when the DMX levels are changing Recording of presets must be done from the MASTER faceplate Using the primary DMX512 console set a look to be recorded Using a small blunt object i e paper clip depress the RECORD MODE recessed button located next to the RED LED The RED LED will begin to flash If you decide after depressing the RECORD MODE button that you do not wish to make an edit depress the RECORD MODE button a second time No changes will have been made 3 Depress the PRESET SELECT button adjacent to the preset number you wish to record The adjacent GREEN LED will illuminate as you depress the button Example press the upper most left button to store preset 1 4 Upon releasing the PRESET SELECT button the RED LED will longer flash This Indicates recording is complete Repeat steps 1 through 4 until you have recorded as many presets as required up to ten total PRESET NUMBER 10 OFF SPECIAL FUNCTION When the levels stored in preset number 10 OFF are all zeros a special function is enabled When preset 10 OFF is selected and the crossfade is completed the
5. SELECT BUTTON RECESSED RECORD BUTTON RECESSED FADE TIME BUTTON FADE TIME INDICATOR LED YELLOW LOCKOUT RECORD INDICATOR LED RED Page 2 of 7 SPECIFICATIONS Connector Connector pin out Input Output Circuit Indicators User controls Option Jumpers Power input Color Size Phoenix Contact MSTB series 5 position two part terminal block Model MSTB 2 5 5 ST 5 08 Order Number 17 57 04 8 1 C DMX512 common 2 DMX512 data 3 DMX512 data 4 C Supply common internally tied to pin1 5 V Supply voltage hot ESD protected EIA 485 transceiver LT1785 Ten green preset indicator LEDs One yellow Fade Time LED One red Signal Record LED Ten preset push buttons One recessed record push button One recessed fade time push button For a single station installation all jumpers should be installed see figure 1 page 5 INSTALLED REMOVED JP1 Recording Enabled Recording Disabled JP2 Master Station Slave Station JP3 Architectural Mode Portable Mode JP4 Single Station Mode Multi Station Mode 9 to 24 volts DC or 10 to 16 volts AC 200mA per station A 10 volt class 2 doorbell transformer is recommended for fixed installations Black anodized with silver engraved nomenclature Faceplate 4 5 h X 2 75 w X 0 2 d Faceplate rear inset 4 05 h X 2 4 w X 0 1 d Electrical box minimum inside dimensions 3 5 h X 2 1 w X 1 25 d PE oi 600 002 700
6. ed for master slave station operation If your system contains only one Preset 10 there is no need to remove the jumper MASTER AND SLAVE SELECTION In a system with more than one faceplate only one MASTER is allowed To modify faceplate to become a MASTER the shunt located at JP2 should be installed and the shunt at JP4 should be removed For safe keeping place the shunt over only one of the pins at JP4 Opa Bd JPS en JPA le JP Figure 1 To modify a faceplate to become a SLAVE the shunts located at JP2 and JP4 should be removed For safe keeping place the shunt over only one of the pins at JP2 and JP4 NN N Figure 2 Page 5 of 7 PRESET 10 ARCHITECTURAL OPERATION INDICATORS GREEN LED ON CURRENTLY SELECTED PRESET FLASHING TIME SETTING MODE SELECTED FOR THIS PRESET YELLOW LED ON PRESET FADE IS IN PROGRESS FLASHING TIME SETTING MODE SELECTED RED LED ON STATION LOCKED OUT RECEIVING DMX512 FROM EXTERNAL CONSOLE FLASHING RECORD MODE ACTIVE GREEN LED YELLOW LED RED LED STATE OFF OFF OFF UNIT NOT POWERED OFF OFF ON RECEIVING DMX512 PRESET 1015 LOCKED OUT FROM TRANSMITTING OFF OFF FLASHING RECORD MODE ACTIVE CURRENT LOOK WILL BE STORED TO THE NEXT PRESSED PRESET FLASHING FLASHING OFF TIME SETTING MODE ACTIVE FOR SELECTED PRESET ON OFF OFF PRESET 10 TRANSMITTING DMX512 NO DMX512 INPUT ON ON OFF PRESET 10 TRANSMITTIN
7. h to play To begin autofollow of all ten presets press and hold the preset select button of preset number 1 approximately 5 seconds until all the LEDs flash once Once the fade time of a preset is complete the next preset will be selected automatically When preset number 10 OFF has been reached the next preset to be selected will be preset number 1 To exit autofollow momentarily press any preset select button Note If a static preset is playing at the time power is lost Preset 10 will return to that preset when power is restored The fade will begin with all 512 channels at 0 and fade up in the time recorded to that preset If the Preset 10 was autofollow playback atthe time power was lost the Preset 10willresume autofollow playback beginning with preset number 1 To bypass unused presets In autofollow enter the time as 999 seconds This means the longest autofollow fade time is 998 seconds PRESET NUMBER 10 OFF SPECIAL FUNCTION When the levels stored in preset number 10 OFF are all zeros a special function is enabled When preset 10 OFF is selected and the crossfade has completed the Preset 10 will stop sending DMX By ending DMX transmission many moving lights and dimming systems will enter their standby mode Page 7 of 7
8. itectural has been designed to operate on a standard class 2 doorbell transformer For example Ace Hardware s model ACE36483 10 volt 5 watt transformer Page 4 of 7 PRESET 10 ARCHITECTURAL SETUP FACEPLATE CONFIGURATION Each Preset 10 Architecturalhas four jumpers JP1 through JP4 that select different modes of operation The factory default is to have all jumpers installed JP1 JP2 JP3 JP4 When this jumper is installed on the MASTER faceplate recording of presets is enabled When removed the TIME and RECORD buttons are disabled The position of JP1 on a SLAVE faceplate has no affect When this jumper is installed the faceplate takes on the MASTER duty The MASTER faceplate is responsible for transmitting and receiving DMX storing presets and communicating with SLAVE faceplates When removed the faceplate takes on the SLAVE duty A SLAVE faceplate communicates button presses and mimics the state of the LEDs on the master faceplate When the jumper is installed the Preset 10 operates as an architectural preset station When this jumper is removed the Preset 10 operates as a console backup portable station This jumper modifies the personality of the Preset 10 software When this jumper is installed it enables SINGLE STATION MODE In this mode the faceplate will not send any alternate start code packets When this jumper is removed it enables MULTI STATION MODE This allows the alternate start code packets requir
9. wed by 2 then OFF The time setting command is completed by one of three methods a Enter a three digit ttme The TIME SETTING MODE will exit upon the entry of the third digit The GREEN preset indicator LED will illuminate steadily and the yellow LED will go off indicating success A one or two digit time may be entered with leading zeros i e five seconds as 005 or OFF OFF 5 b Enter a one or two digit time followed by pressing the TIME SETTING MODE button The GREEN preset indicator LED will illuminate steadily and the yellow LED will go off indicating success Enter one or two digit time and wait for ten seconds for the time setting mode to exit automatically The GREEN preset indicator LED will illuminate steadily and the yellow LED will go off indicating success PLAYBACK OF PRESETS Presets can be played back in one of two ways a crossfade to a static preset or an autofollow of all ten presets A crossfade is a change from the current preset to the newly selected one The time taken to fade from the current preset to the new preset is taken from the newly selected preset Once the fade has completed it will remain at that current preset static until another preset is selected When the autofollow method of playback is used once the fade time of the currently fading preset is completed the next preset is automatically selected To begin a crossfade between presets momentarily press the preset select button of the preset you wis
Download Pdf Manuals
Related Search