Downloads
Contents
1. SPECIICALONS ita ana 10 Contents Chapter 1 Product Introduction Evoe Chapter 1 Product Introduction Overview JDS 1902ESP is a rugged panel display with 19 LCD which is configured with 19 wide temperature and high luminance LCD with VGA and DVI connectors the OSD keystroke on the front panel can adjust the parameters as luminance and contrast etc The box PC possesses reasonable structure al alloy panel stainless steel and closed design chassis dust proof and water proof switch and aviation plugs which could effectively prevent dust and vapor from entering the chassis With full consideration to the requirements of harsh outdoor application environments this product adopts special rugged design and vibration insulation technique high quality wide temperature materials and assemblies relevant shielding filtering and grounding measures in EMC and optimizes the heat dissipation design to improve the environment performance of the product The product complies with the requirements of military standards JDS 1902ESP is a cost effective panel display which supports panel mounting mode and rear cover VESA mounting mode It can be widely applied in the fields such as telecommunication electric power multimedia national defense industrial automation devices and manufacturing etc Main Performance EMC Complies with CE102 CS101 CS114 RE102 and RS103 of GJB151A Reliability MTBF gt 10000h MTTR lt 0 5h JD2. JDS 1902ESP Rugged Panel Display Version C00 Evoc Copyright Notice Information offered in this manual is believed to be correct at the time of printing and is subject to change without prior notice in order to improve reliability design and function and does not represent a commitment on the part of the manufacturer In no event will the manufacturer be liable for direct indirect special incidental or consequential damages arising out of improper installation and or use or inability to use the product or documentation This user manual is protected by copyright No part of this manual may be reproduced stored in any retrieval system or transmitted in any form or by any means mechanical electronic photocopied recorded or otherwise without the prior written permission from the manufacturer Trademarks EVOC is a registered trademark of EVOC Intelligent Technology Co Ltd Other product names mentioned herein are used for identification purposes only and may be trademark and or registered trademarks of their respective companies Please visit our website http www evoc com for more information Or send to the Technical Support Mailbox support evoc com or support evoc cn for consultation Evoe 10 Safety Instructions Please carefully read the User Manual before handling the product Please do not use the display with power supply other than the specified ones improper voltage may cause failure even the danger
3. S 1902ESP 1 E Evoc Chapter 1 Product Introduction Safety Meets the basic requirement of GB4943 Mechanical and Environmental Adaptability O Anti vibration 5 19Hz 1 0mm amplitude 19 200Hz 1 5g acceleration operation direction 15 minutes Anti shock 20g acceleration 11ms duration half sine wave thrice at the operation direction Requirements of Transportation and Storage e Transportation Well packaged products are suited for transportation by truck ship and plane During transportation products should not be put in open cabin or carriage When transshipping en route products should not be stored in open air without protection from the atmospheric conditions Products should not be transported together with inflammable explosive and corrosive substances and are not allowed to be exposed to rain snow and liquid substances and mechanical force o Storage Products should be stored in package box when it is not used And warehouse temperature should be 0 C 40 C and relative humidity is 20 85 In the warehouse there should be no harmful gas inflammable explosive products and corrosive chemical products and strong mechanical vibration shock and strong magnetic field affection The package box should be at least 10cm above ground and 50cm away from wall thermal source and vent 2 JDS 1902ESP Chapter 2 Installation Evoe Chapter 2 Installation Product Outline O Front View Rear V
4. er surface of the front panel where water proof silicone pad needs to be installed while silicone rubber sealant shall be applied at the root of the fixing screws on the press button pad Assemble the shielding tempered glass and L shaped sealing stripe on the front panel correctly Note the sealing stripe shall be sealed with soft silicone rubber at the joining corner and then install them on the chassis Fasten the glass plate on the front shell with 6 32 countersunk head screws of American form correctly so as to press the shielding tempered glass and L shaped sealing stripe tightly Stick the shock absorption sponge on the joining surface between the LCD bracket and the LCD screen install them on the box PC Note install the long block and the short block correctly on the box PC and fasten with M3 6 combined screws The joining part for heat dissipation shall be applied with heat dissipation silicone rubber or stuck with heat dissipation pads Install the filter power board controlling board and inverter in the box PC correctly Assemble the three aviation sockets with the IO side board and put them on the IO bracket Connect the cable and well fix them After covering the rear shell Note during installation make the IO side board rise outward and upward so as to facilitate the installation of the rear shell fasten the rear shell with M4 10L countersunk head screws and the IO side board module with M3 8 combined screws with mountin
5. g pad As it is a 6 JDS 1902ESP e Chapter 2 Installation Evoc water proof box PC O shaped sealing stripes shall be installed between the front and rear shell as well as the IO side board and the rear shell 7 Finally install the handles from front and fasten with M5 12L combined screws with mounting pads JDS 1902ESP 7 l Evoe Chapter 3 Instructions Chapter 3 Instructions Adjust OSD 1 Press MENU to enter the OSD main menu 2 Press gt lt to choose between the options If you want to adjust highlight function press MENU to activate the menu If submenus are included in the chosen function press MENU again to browse the functions of the submenu 3 Press gt lt to change the setting for the chosen function 4 To exit or save please choose off function If you want to adjust any other functions please repeat step 2 3 8 JDS 1902ESP FA Chapter 3 Instructions Evoe Instructions for Function Control Items lo Tonia Items in Submen Instruction Main Menu Main Menu Giai REE E ER 1 Offline Adjust the contrast Image SAR luminance backlight 3 Contrast Quality GAMMA of the 4 Backlight 5 GAMMA digital recorder 1 Offline Adjust the horizontal Automatic Adjustment Image Horizontal Position position vertical Position Vertical Position position focus time C
6. iew Product Appearance and Installation Dimensions E Is t P I Ts ase T NI se E usd t RA LP i i FP 09000 i i 189 MT Unit mm JDS 1902ESP 3 ak Evoe External Connectors PEPER ve Chapter 2 Installation 5 4 Lglo 4 Front View 1 POWER 2 MENU 3 gt Right Key 4 lt Left Key 5 AUTO 6 POWER LED Rear View 1 DVI 2 VGA 3 Power JDS 1902ESP de Chapter 2 Installation Evoe Critical Parts Assembly Drawing Control ling P Lu a Power Filter _ LCD Bracket Inverter I0 Side Panel LOD Short Block Long Block 7 Glass Plate L Shaped lt Sealing Stripe 7 Front Panel Shielding Tempered Glass _ Controlling Panel Inverter _ Power i A Board x Handle ae Y 7 I Filter LED Pressbutton D 2 Indicator Switch o JDS 1902ESP 5 Evoc Chapter 2 Installation Critical Parts Installation Steps 1 Firstly install the press button switch and LED indicators on the front panel Note they should be installed with water proof function therefore 3M Moisture Barrier Glue shall be stuck at the inn
7. lock sequence of the image Phase 1 Offline Automatic Color Automatically adjust Color Mod Color a the color for the Red Adjustment image Green Adjustment Blue Adjustment 1 Offline Select the display System 2 Language Selection 3 Menu Selection Time languages of the OSD Setting 4 Standby Time menu 5 Reset 1 Exit Exit 2 Choose VGA Signal Select Input Signal 3 Choose DVI Signal JDS 1902ESP Chapter 3 Instructions Evoc Specifications Display TFT Color LCD Device LCD Panel Dimensions 48 26 cm 19 Dot Pitch 0 294 mm x 0 294 mm Red blue green analog interfaces and Video Input DVI digital connector Frequency 60Hz 75Hz Maximum Resolution 1280 1024 Displaying Color 16 7 M colors Power Consumption 28 W Typ 6 5mA Input Connector Aviation Plug Power Rated Value 100 240V 50 60Hz Limit 90 264V 47 63Hz Environment Temperature and Humidity Operating Temperature 15 C 60 C Storage Temperature 40 C 65 C Shell Protection Panel is compliant with IP65 while the box PC is compliant with IP43 Net Weight 10 3Kg without cables 11 3Kg with cables Box PC Dimensions 482 6mm L x 398mm W x 69 7mm H JDS 1902ESP 10
8. of fire or electric shock Please do not use the display with the cover open Please do not insert anything into the display Please do not touch the plug with damp hands Please do not install the display where temperature might change suddenly or with great humidity dust or smog Please ensure abundant cooling and ventilation Before connecting the display with the PC please power off the PC and the display Before moving the display please make sure it is powered off and the display plug and the signal cable are removed Non professional personnel are not allowed to open the chassis Chapter 1 Product Introduction cono nnnonncnnncn nono 1 O tica ac iene ii 1 Ma PELO O fsi 1 EME ee ea dl dad ed a RE a 1 Reliability iio lali dla iii 1 diri cid avellino la diana 2 Mechanical and Environmental Adaptability iii 2 Requirements of Transportation and Storage i 2 Chapter 2 Ifistallationi udlisheigorla Geena la nas 3 Product Outline ernia leleine lara 3 Product Appearance and Installation DiMmensions i 3 External Contiectors ni giaigutalicule ne die ia ilaria e Eaa 4 Critical Parts Assembly Drawing iii 5 Critical Parts Installation StepS canon nonnnnnnnn non no nono nncnnncn nono 6 Chapter 3 INStructions cini aaa iaia alan i 8 Adj st OSD siria ail 8 Instructions for Function COntrol ii 9
Download Pdf Manuals
Related Search