- Aplisens SA
Contents
1. In case when window is used for preview converter s condition during transmission to transmitter the window should be closed by pressing Cancel button each pressing OK will result in necessity to detect transmitter one more time and will delete collected measurement data Converter is equipped with radio module operating in band 2 4 GHz ISM Class 1 what will ensure together with Bluetooth adapter of the same class range up to 100m in open space In case when Bluetooth Class 2 or built in module adapter is used the range of radio communication is reduced to 10m in open space 27 DTR HB 01 Zalacznik A Range of radio connections can be reduced as a result of interference with near devices transmitting band 2 4 GHz such as mobile phones wireless networks even microwaves Presence of such devices will worsen quality of the radio connection what can result in repeated queries from HART communication A9 TROUBLESHOOTING CONNECTION VIA BLUETOOTH Typical examples of problems connected with converter s operation and solutions are presented below Converter does not switch on STAT diode is not flashing Press shortly POWER button e In case when there is no reaction of any LED diodes connect converter with computer or charger using USB cable gt Ifred diode lights it means that internal battery of the converter is charged User should leave device connected to USB until battery is fully charged what will2. Device driver software installed successfully and appropriate device will be displayed in device manager 20 DTR HB 01 Zalacznik A ah amzy7 9 Bluetooth Radios Z F ASUS Bluetooth v2 1 USB Adapter 53 Microsoft Bluetooth Enumerator Computer Ga Disk drives Display adapters 45 DVD CD ROM drives 53 Human Interface Devices Fe r Now computer is ready to assign remote Bluetooth devices pairing what will result in creation of virtual serial ports in the system which are matched with proper device Then user should pair HART USB Bluetooth Converter with computer To do this user should switch on converter if it is switched off make sure that it is operating correctly STAT diode must be flashing search for Bluetooth device with appropriate name and add it to registered devices Caution Searching pairing and assigning of serial port procedure can be very different from this one which is described It depends the model of USB Bluetooth dongle converter used on software used Bluetooth stack servicing Bluetooth device from computer s side as well as on operating system used Caution if it is required to install more than one converter operations for each converter are analogical case of problem with identification of the converter before installation need to obtain Bluetooth ID of individual converter see p A9 Troubleshoot
3. 2GHz 3V m 2GHz 2 7GHz 1V m Criterion A Electrical Fast Transient Burst Immunity EN 61000 4 4 1kV Criterion A Electrical Slow Transient Surge Immunity EN 61000 4 5 1kV Criterion B 5 4 2 Electromagnetic Compatibility emission According to EN 55022 radiated emission Distance to the antenna 3m quasi peak measuring 1GHz 3GHz 70dBuV m 3GHZ 6GHz 74dBuV m 5 4 3 Climatic immunity Ambient temperature EN 60068 2 1 EN 60068 2 2 Dry heat T 60 C RH max 55 Cold T 20 C 5 4 4 Mechanical immunity shocks EN 60068 2 27 500 11 5 vibrations EN 60068 2 6 test Fc up to 1 6mm for 2 25Hz up to 4g for 25 100Hz 5 4 5 Insulation Resistance gt 100 MQ 110V DC 5 4 6 Enclosure ingress protection Rating according to EN 60529 IP 20 5 DTR HB 01 ENG 6 CONSTRUCTION Device is placed in the enclosure made of polystyrene where two sockets are located on the opposite walls first for connection of USB cable equipped with B type plug second RJ45 8 type for connection of HART communication cable PLISEN HART USB Bluetooth Converter Fig 1 Front view of the converter There are two buttons RESET and POWER and two LED diodes STAT and BATT located on the front wall POWER button is intended for use of the converter Second button is intended for full reset of the converter in case of problems with establishing transmission and it is not necessar
4. Products 18 SCRAPPING DISPOSAL Waste or damaged converters should be dismantled and disposed of in accordance with Directive 2002 96 EC on waste electrical and electronic equipment WEEE or returned to the manufacturer 19 REFERENCE DOCUMENTS Raport 2 application User s manual of the device with HART interface 18 DTR HB 01 Zalacznik A ANNEX A SERVICING OF THE CONVERTER DURING WIRELESS CONNECTION VIA BLUETOOTH A1 INTRODUCTION Additional information indispensable for correct servicing of the HART USB Bluetooth Converter during wireless connection through Bluetooth interface are presented in this annex This DTR HB 01 ENG and Annex A should be used during use of this converter in wireless connection via Bluetooth interface mode A2 TECHNICAL DATA A2 1 HARDWARE REQUIREMENTS Bluetooth adapter installed in the computer together with installed drivers enabling operation in SPP Serial Port Profile mode or USB socket intended for connection of external USB Bluetooth adapter Windows 7 operating system Access the computer with USB socket power unit with USB socket voltage compatible with USB standard intended for periodic charging of the internal battery Microsoft NET Framework version 2 0 or newer for HUBC Configurator application A3 WIRELESS CONNECTION OF THE CONVERTER THROUGH BLUETOOTH INTERFACE Method of connection of the converter to the transmitter and to computer is presen
5. SOFTWARE INSTALLATION AND CHECKING OF CONNECTION A4 1 HARDWARE REQUIREMENTS In case of use of Bluetooth connectivity user should ensure devices suitable for this purposes that is make sure that computer is equipped with built in Bluetooth module or use appropriate external module In case of desktop computers or portable without built in Bluetooth module a typical solution is USB Bluetooth converter so called Bluetooth dongle USB Bluetooth converter is supplied with own drivers which should be installed if Windows OS will not offer other driver E g Sweex BT214 converter is operating correctly using Microsoft driver included in Windows 7 OS while Asus BT214 requires use of special driver it is not identified correctly by Windows Installation of USB Bluetooth converter and adding it to the system will be presented on the basis of Asus converter Installation of driver from enclosed CD is as following when disc is inserted it will attempt to automatically read its content user should allow starting autorun if system will ask installation software will be started User should select Install ASUS Bluetooth Card Utilities Driver Installation will be started after pressing OK button and will proceed automatically system will indicate that converter s drivers are installed Installing device driver software Click here for status then the fact of its installation ML Your device is ready to use
6. as operation within the range of battery s temperatures from 20 C to 60 C When boundary values are exceeded operation of the converter is stopped Return to operation is made after increasing of temperature by 5 C when lower temperature threshold operation or charging is exceeded or decreasing it by 5 C when the upper threshold was exceeded 11 4 INFLUENCE OF BATTERY CHARGING ON OPERATION OF THE CONVERTER CHARGING TIME In case when converter will detect that battery is excessively discharged it will be protected against damage by switching off majority of peripherals and switching to reduced power consumption mode Device in this state is not operating it applies also to reset LED diodes are not flashing the only possible operation is to charge the battery by connecting the converter to USB port of the computer or charger Caution user should not allow leaving the converter even switched off without charging for longer than 6 month period especially when battery has not been fully charged It can lead to activation of 2 level protection installed in the battery what will result in significant increase of time 11 DTR HB 01 ENG necessary to restore battery to usability state by charging and can have a negative influence on its durability In case when battery cannot be charged the converter should be sent to service in order to AN replace the battery Battery can be replaced only by the manufacturer or authorized unit T
7. be signaled by change of BATT diode s colour to green Converter is ready for operation after charging the battery gt If green diode is lighting and device can be switched on it means that there is different problem with battery e g too strong chilling of the battery or its natural wear If this problem will occur again user should contact service gt If after connection of USB cable device cannot be switched or diode does not light then device should be restarted by pressing RESET button If converter cannot be switched STAT diode is signaling correct operation test should be repeated In case when after performing of the above mentioned operations the converter still cannot be switched on user should contact service il It is not recommended to establish connection with converter via Bluetooth during restarting the device connection will not be established It is impossible to establish connection with the transmitter through a HART using Bluetooth Disconnect converter from computer if it was connected it blocks Bluetooth transmission Check whether converter is switched and it works STAT diode must flash Establish whether connection with converter can be established among other things in the following way e Check which serial port is assigned to converter in the Windows system It can be made in the following way gt Observing the Device Manager wind
8. cable device cannot be switched on or BATT diode does not light then device should be restarted by pressing RESET button If converter cannot be switched on and STAT diode is not signalling correct operation test should be repeated In case when after performing of the above mentioned operations the converter still cannot be switched on user should contact service It is not recommended to establish connection with converter via Bluetooth during restarting the device connection will not be established It is impossible to establish connection with the transmitter through a HART using USB Establish whether converter is switched on and STAT diode is flashing Search for serial port assigned to the converter in system It can be determined e g by observation of Device Manager window in system branch Ports during connection of the USB cable to the computer New serial port should be displayed e f converter had not been detected it can indicate that USB port is damaged cable is damaged or driver of serial port in system had not been installed e If Windows operating system is signalling device conflicts not installed drivers or unknown devices especially USB such problems should be solved first e If many USB serial devices were connected to computer and a lot of ports were installed reserved user can try to uninstall part of them Establish connection with the converter using Configurator softwa
9. it until STAT diode switches off STAT diode which is emitting short flashes during normal operation will light up during pressing the button and then it will go out Serial port remains active but it will not transmit any data Switch on converter from the standby to normal operation mode Shortly press button Converter is immediately ready for transmission through USB BATT diode will signal battery charging state by flashes and then it will change colour to red or green if charging is made through USB or it will be switched off if USB is not connected STAT diode will start to emit short flashes Check charging state of the battery Shortly press button for this purpose Converter will signal battery s state as it is presented above 10 DTR HB 01 ENG Activity of RESET button It is used for hardware reset of the device It should be used when converter is not reacting on POWER button and or connection cannot be established z Approx 30 seconds are necessary to restart the device During mentioned 30 seconds the converter will not react to POWER button and will not be ready for transmission STAT diode will signal restarting course STAT diode signaling Flashing normal operation Sequence of longer flashes device restart Constant flashing after longer pressing of the POWER button during switching of the converter to standby State Squawk different flashing which is set from the level of control software ena
10. things preview battery charging state In case when window is used for preview converter s condition during transmission to transmitter the window should be closed by pressing Cancel button each pressing OK will result in necessity to detect transmitter one more time and will delete collected measurement data 13 2 CONVERTER CONNECTED TO THE COMPUTER VIA BLUETOOTH In case of wireless connection of the converter with computer to establish connection with the transmitter user should proceed as presented in Annex A p A8 16 DTR HB 01 ENG 14 TROUBLESHOOTING CONNECTION VIA USB Typical examples of problems connected with converter s operation and solutions are presented below Converter does not switch on STAT diode is not flashing Press shortly POWER button e case when there is no reaction of any LED diodes connect converter with computer or charger using USB cable gt Ifred diode lights it means that internal battery of the converter is charged User should leave device connected to USB until battery is fully charged what will be signalled by change of BATT diode s colour to green Converter is ready for operation after charging the battery gt If green diode is lighting and device can be switched on it means that there is different problem with battery e g too strong chilling of the battery or its natural wear If this problem will occur again user should contact service gt If after connection of USB
11. AT diode is flashing Connect USB cable to the converter and computer Check connection according to the p 9 Start Raport 2 application then select menu item Program settings The following window will be displayed Program settings x Protocol Hart Modem HUBC Plugin Configuration OK Cancel Select options in turn Protocol Hart Modem HUBC Plugin Clicking selection bar Configuration will open window presented below enabling to configure the converter s setting COM Port y DTR HB 01 ENG Descriptions Aplisens HUBCrev3 Aug 10 2012 Rev 0105 00 12 6 23 8 84 USB 0x0000 0 0014 Added preambles 0 Frameslost 0 Battery Battery Battery T Battery U Time to Power Off 15 Squawk T USB Compliant Reverse CD Polarity Sensitivity Output Gain It offers the same functions as HUBC Configurator application and can be used interchangeably with HUBC Configurator application setting made by the user are stored in the converter until the device is reset Select appropriate COM port Make single data readout to ensure that there is connection with converter If changes are needed user should proceed according to the p 12 Close window by pressing OK if changes were made then use Raport 2 application according to its servicing instruction User can use settings window during work for among other
12. GPLISEN 5 DTR HB 01 ENG APLISENS MANUFACTURE OF PRESSURE TRANSMITTERS AND CONTROL INSTRUMENTS USER S MANUAL HART USB BLUETOOTH CONVERTER WARSAW JUNE 2012 APLISENS S A 03 192 Warszawa ul Morelowa 7 tel 48 22 814 07 77 fax 48 22 814 07 78 www aplisens pl e mail aplisens aplisens pl Symbols used Symbol Warning to proceed strictly in accordance with the information contained in the documentation in order to ensure the safety and full functionality of the device Information particularly useful during installation and operation of the device e Information on disposal of used equipment BASIC REQUIREMENTS AND SAFE USE The manufacturer will not be liable for damage resulting from incorrect installation failure to maintain the device in a suitable technical condition or use of the device other than for its intended purpose Installation should be carried out by qualified staff having the required authorizations to install electrical devices The installer is responsible for performing the installation in accordance with these instructions and with the electromagnetic compatibility and safety regulations and standards applicable to the type of installation The device should be configured appropriately for the purpose for which it is to be used Incorrect configuration may cause erroneous functioning leading to damage to the device or an accident If a device is not functioning correctly disconnect i
13. ION 12 1 CONVERTER CONFIGURATION VIA USB PORT AND HUBC CONFIGURATOR APPLICATION 12 2 CONVERTER CONFIGURATION VIA BLUETOOTH 13 ESTABLISHING CONNECTION WITH TRANSMITTER WITH HART PROTOCOL 13 1 CONVERTER CONNECTED TO THE COMPUTER VIA USB 13 2 CONVERTER CONNECTED TO THE COMPUTER VIA BLUETOOTH 14 TROUBLESHOOTING CONNECTION VIA USB 15 MAINTENANCE SPARE PARTS 16 PACKING STORAGE AND TRANSPORT 17 WARRANTY 18 SCRAPPING DISPOSAL 19 REFERENCE DOCUMENTS QI 8 GO GO GO Q O N N N NAAA SERVICING OF THE CONVERTER DURING WIRELESS CONNECTION VIA BLUETOOTH A1 INTRODUCTION A2 TECHNICAL DATA A2 1 HARDWARE REQUIREMENTS 4 SOFTWARE INSTALLATION AND CHECKING OF CONNECTION A4 1 HARDWARE REQUIREMENTS A4 2 WIRELESS CONNECTION OF THE CONVERTER VIA BLUETOOTH INTERFACE A5 BUTTONS AND LED DIODES 7 CONFIGURATION OF CONVERTER CONNECTED VIA BLUETOOTH INTERFACE 8 ESTABLISHING CONNECTION WITH TRANSMITTER WITH HART PROTOCOL A9 TROUBLESHOOTING CONNECTION VIA BLUETOOTH 2 DTR HB 01 ENG 1 INTRODUCTION 1 1 This Manual is intended for users of HART USB Bluetooth Converters hereinafter referred to as converters containing date and guidelines necessary to understand
14. and lost frame are intended mainly for estimation of Bluetooth connection s quality band occupancy The more preambles added the worse transmission conditions are present Detailed description of the preambles addition mechanism is included in the p 12 Switch Reverse CD Polarization can be switched during Bluetooth connection but it has no 1 application in such case CD signal is not available during radio transmission see p 12 A8 ESTABLISHING CONNECTION WITH TRANSMITTER WITH HART PROTOCOL Establishing connection with transmitter through a converter will be described on the example of Raport 2 application created by Aplisens S A To establish connection with transmitter user should perform the following operations Connect HART cable into measurement loop of the transmitter on resistor s terminals Ro 22500 according to the user s manual of the transmitter Switch on converter and make sure that STAT diode is flashing 25 DTR HB 01 Zalacznik A Do not connect USB port in computer to converter cable connection always will switch transmission to USB port switching off Bluetooth module and will make its detection impossible Make sure that Bluetooth module in computer is functioning or connect external Bluetooth adapter and that is paired with converter pairing procedure is described in p A9 Software installation Establish number of serial port e g check in device manager or in properties of added Bluetooth devic
15. bles to indicate in case of many converters which converter is currently controlled BATT diode signaling Red light battery charging through USB Green light battery charged Flashing signaling of battery charging state after short pressing of POWER button according to description in p 11 Power supply No converter s reaction on buttons and if diodes are not switched on it can be a result of battery s discharge device is protecting battery against further discharge by automatic switch to sleep mode 11 POWER SUPPLY 11 1 CHARGING CURRENT Battery is charged after connection of the converter to the computer s or charger s USB port Charging current depends on compatibility of USB module in computer host with USB 2 0 specification as well as activation of USB Compliant mode in computer see p 13 Establishing connection and is equal to in the easiest case 100 mA and maximum 330 mA In case when USB host is reporting switching to sleep mode e g user switched off the computer and USB Compliant mode is switched on then charging is stopped 11 2 TOOL INTENDED FOR CHARGING Computer with USB port Charger e g telephone with USB port Input voltage AC 100 240V 50 60 Hz or DC 12 24V Output voltage DC 5V 500 mA 11 3 INFLUENCE OF TEMPERATURE ON SUPPLY Charger built in the converter checks temperature of battery and permits charging within temperatures range of the battery from 0 C to 45 C as well
16. can try to reduce distance from the computer to converter If Bluetooth devices connected to computer and or many serial ports connected with these devices user should try to remove these devices and serial ports and then repeat searching and adding of new device Examples of correctly installed HART USB Bluetooth Converter are presented above When the correct serial port is found user should connect with it using HUBC Configurator application application is described in p A12 Configuration of converter User should press button Read in the application s window and check state of the converter 29 DTR HB 01 Zalacznik A Proceed further as described in point concerning problem with establishing connection with transmitter via USB p 14 There are many converters within the range of computer but only part of them should be installed How to recognize them It is undesirable to install all converters detected by computer e g taking into account further conflicts between computers connecting to the same converter To identify converter user can use a fact that its Bluetooth address is presented also during USB connection Connect converter via USB Start HUBC Configurator application remembering to select appropriate serial port Make a readout and note converter s address presented in window see red highlight HUBC Configurator eae x COMPot 52 gt Descriptions r
17. computer equipped with built in or connected external Bluetooth interface 3 2 Connection using the converter is point to point type and proper computer software ensures detection of the converter as virtual serial port both in case of USB and Bluetooth connection Transmitters with HART interface connected through the converter can be serviced by a software intended for communication with transmitters through a serial port e g Raport 2 PACTware or FieldCare through CodeWrights HART Communication DTM and others please note that radio communication via Bluetooth will be possible using application which are not requiring Carrier Detect CD signal The condition is that communication software HART has to correctly recognize and service virtual serial ports Thus converter enables operation on computers not equipped with RS232 port and especially on portable devices New converter should be connected to computer s or charger s USB port in order to charge internal battery Lighting green diode indicates that charging is completed User should regularly check state of internal battery s charge in the converter 3 DTR HB 01 ENG 4 IDENTIFICATION MARKING METHOD OF MARKING DURING ORDERING 4 1 Each converter is equipped with rating plate containing at least the following information CE mark name and address of the manufacturer marking of the product serial number type of battery and supply voltage Method of marking
18. during ordering acc to the Specification Sheet of the converter 5 TECHNICAL DATA 5 1 HARDWARE REQUIREMENTS 5 1 1 Wire connection through USB connector Computer equipped with USB connector USB 2 0 Full Speed compatible interface Operation system Windows XP or newer Microsoft NET Framework version 2 0 or newer for HUBC Configurator application 5 1 2 Hardware requirements concerning wireless connection via Bluetooth are presented in the Annex 4 1 5 2 ALLOWABLE AMBIENT AND OPERATION PARAMETERS Range of operation temperatures 20 C 60 C Range of charging temperatures of the internal battery 0 C 60 Relative humidity lt 95 without condensation 5 3 OPERATIONAL PARAMETERS Power supply internal battery Li lon 1950 mAh cell Panasonic type CGA 103450A Maximum charging current of battery 330mA Operation time on fully charged battery more than 8h Maximum storage time with fully charged battery converter switched off at room temperature 6 months Material of enclosure polystyrene 4 DTR HB 01 ENG 5 4 PERMITTED ENVIRONMENTAL CONDITIONS 5 4 1 Electromagnetic Compatibility EMC immunity Rating according to EN 61326 1 2 Electrostatic Discharge Immunity ESD EN 61000 4 2 S3 level Contact 6kV Air 8kV Criterion A Conducted Radio Frequency EN 61000 4 6 0 15 80MHz 10V Criterion A Radiated Electromagnetic Field EN 61000 4 3 80 2 1GHz 10V m 1 4GHz
19. e Start Raport 2 program and open settings window Protocol Hart M Modem HUBC Plugin Configuration 10 OK Cancel Select options in turn Protocol Hart Modem HUBC Plugin Clicking selection bar Configuration will open window presented below enabling to configure the converter s setting COMPort 10 y 26 Descriptions Bluetooth ID Communication via Aplisens HUBCrev3 Aug 10 2012 0105 00 12 6f 23 8a 84 Bluetooth Status 0 0000 Reset 0x0010 Added preambles 0 Frames lost 0 Battery Battery Battery T Battery U 4 11 Settings Time to Power Off Squawk USB Compliant I Reverse CD Polarity I Standard h Large js min r Sy Power Off Reset to defaults ox coma Output Gain The window offers the same functions as HUBC Configurator application and can be used interchangeably with HUBC Configurator application setting made by the user are stored in the converter until the device is reset Select appropriate COM port Make single data readout to ensure that there is connection with converter If changes are needed user should proceed according to the p 12 Close window by pressing OK if changes were made then use Raport 2 application according to its servicing instruction User can use settings window during work for among other things preview battery charging state
20. eck whether connection with converter can be established user should start application HUBC Configurator Start Menu All programs Aplisens HART USB Bluetooth Converter Application s window is presented below Appropriate COM port in this case COM10 should be selected from the list and button Read should be pressed Port comio Aplisens HUBCrev3 Aug 10 2012 Rev 0105 00 12 6f 23 83 84 Bluetooth Battery U Settings Time to Power Off Squawk USB Compliant Reverse CD Polarity Power Off Output Gai a ae Reset to defaults After several seconds information in application s window will be refreshed what means that they are correctly read from the converter and it is ready for operation Readout delay is a result of the fact that program is establishing new connection with converter each time then serial port is released switched on Troubleshooting information regarding the converter is included in the Annex A9 If data is not read and program is signaling error user should make sure that converter is Troubleshooting 23 DTR HB 01 Zalacznik A A5 BUTTONS AND LED DIODES According to the p 10 of this manual with taking into consideration of the following remarks After switching of the converter into sleep mode during operation via Bluetooth device will be 1 disconnected and serial port will be closed gt Switching the converter
21. folder To continue dick Next If you would like to select a different folder dick Browse C Program Files Aplisens HART USB Bluetooth Converte Atleast 2 0 MB of free disk space is required coa 8 DTR HB 01 ENG Then user should select version of the installation Setup HART USB Bluetooth Converter x Select Components Which components should be installed Select the components you want to install clear the components you do not want to install Click Next when you are ready to continue Full installation Ed HUBC Configurator Modem plugin for Raport 2 HUBC Plugin 126 KB Tool for upgrade firmware HUBC Flash Loader 422 KB Current selection requires at least 2 7 MB of disk space lt Back Next gt Cancel If user does not expect to update converter s firmware on his own switch next to the option Tool for upgrade firmware HUBC Flash Loader should be unchecked Detailed information about exchange of converter s firmware updates are contained in the help file of HUBC Flash Loader In case when installer will detect program Raport 2 installed in system it will install automatically plugin called HUBC Plugin This plugin enables configuration of the converter from the level of Raport 2 application During first connection of the converter via USB port the system will automatically install drivers of USB controller which is built in the converter If operating system w
22. ill not find automatically drivers these should be found manually in subfolder Drivers 9 2 CHECKING OF CONNECTION THROUGH USB CABLE After correct installation of the drivers new serial port should appear in the system visible only when USB cable is connected to switched on converter It will be discussed on the example of COM13 serial port To check whether connection with converter can be established user should start application HUBC Configurator Start Menu All programs Aplisens HART USB Bluetooth Converter Application s window is presented below 13 port should be selected from the list and button Read should be pressed 9 DTR HB 01 ENG Port y Dh Aplisens HUBCrev3 Aug 10 2012 Rev 0105 00 12 6 23 8 84 USB 0000 Battery U Settings Time to Power Off Squawk USB Compliant Reverse CD Polarity After several seconds information in application s window will be refreshed what means that they are correctly read from the converter and it is ready for operation If data cannot be readout and program is signaling error user should firstly make sure that the converter is switched on Troubleshooting information regarding the converter is included in the p 14 10 BUTTONS AND LED DIODES POWER button can be used to execute the following operations Switching off the converter that is switch it to standby mode Press button and hold
23. ime required for complete charging of new and completely discharged battery using 100 mA current is equal to about 20 hours In case of bigger voltage 330 mA this time is shortened to approx 7 hours user should get acquainted with option Compatibility with USB presented in p 12 11 5 SIGNALING OF CHARGING STATES Device is signaling battery s charging state on two ways after short pressing of POWER button the BATT diode will signal battery s charging state by flashing User can also use HUBC Configurator application to connect with the converter or use Raport 2 application HUBC Plugin and then read battery s charging state bar Battery Light code of the BATT diode is following Four flashes charging state 80 100 Three flashes charging state 50 80 Two flashes charging state 20 50 One flash charging state below 20 charge battery urgently Percentage values of charge are approximate and are based on estimation of charging state on the basis of battery s voltage and its temperature It is not recommended to use battery which is charged less than in 20 12 CONVERTER CONFIGURATION 12 1 CONVERTER CONFIGURATION VIA USB PORT AND HUBC CONFIGURATOR APPLICATION After correct installation of the USB drivers user can establish connection with the converter to read its state check connection or make a configuration HUBC Configurator application is used for this purpose Application will open single w
24. indow after start This window is presented below 12 DTR HB 01 ENG 21515 13 y m Descriptions Aplisens HUBCrev3 Aug 10 2012 Rev 0105 00 12 6 23 8 84 USB 00000 Descriptions of the individual field of the configurator s window presented the table Field name Function and operation COM Port It contains serial ports currently detected in the system User should select serial port matched with the converter switch on converter and make sure that it is operating STAT diode is flashing then press Read button Serial port will be opened and data from converter will be read and then port will be closed In case of USB it is almost immediately If incorrect data will be displayed in the program s window or program will issue message about error it means that there is connection with the converter user should get acquainted with p 9 Software installation and 14 Troubleshooting Descriptions frame The frame presents in turn Internal name of the converter Date of last software compilation firmware of the converter as well as number of revision of this software Unique Bluetooth address of the converter readout also during connection through USB even Bluetooth module is not active Currently selected communication channel USB or Bluetooth Status frame Frame contains cumulative information concern
25. ing Searched device HART USB Bluetooth Converter is displayed as Aplisens HUBC 3 during searching r 27 Add device Select a device to add to this computer Windows will continue to look for new devices and display them here a Aplisens HUBC r3 DKE CWIAKALA ii Bluetooth Bluetooth Other Desktop computer User should select this device by double clicking 21 DTR HB 01 Select a pairing option gt Create a pairing code for me The device has a keypad Enter the device s pairing code Aplisens HUBC 3 The device comes with a pairing code Check for one on the device or in the device manual Enter the pairing code for the device This will verify that you are connecting to the correct device 1234 The code is either displayed on your device or in the information that came with the device Aplisens HUBC r3 Device should be added Then it should be checked which serial port has been assigned to the device in mode SPP Serial Port Profile 4 Devices 1 This Bluetooth device offers the following services To use a service select the check box Bluetooth Services Serial port SPP SPP 22 DTR HB 01 Zalacznik A is correct in this case Then user should install the application following the procedure given in p 9 1 of this manual A4 2 WIRELESS CONNECTION OF THE CONVERTER VIA BLUETOOTH INTERFACE To ch
26. ing USB or Bluetooth transmission collected from last reset of the converter or deleting errors Labels Errors and Flags contains coded information about transmission errors with transmitter Labels Added preambles and Frames lost gives information about activity mechanism intended for adding HART preambles which eliminates the results of often occurring especially during wireless transmission 13 DTR HB 01 ENG effects of data holding what can result in transmission stoppage Label Added Preambles gives information about number of preambles added by converter to HART frame Label Frames lost gives information about number of HART frames which had been lost despite extension of preamble Reset button is used to delete data concerning errors and added preambles which are stored in the device Battery Gives information about approximate expressed in percent battery charging state frame measured voltage and temperature of battery Settings It allows to configure the following parameters of the converter frame 2 Time to Power Off value of time in min after which the converter will be switched to sleep mode in case of lack of communication Value 0 indicates switching off the function Option Squawk switches on if selected blinking of STAT diode with period of approx 2 55 and duty cycle approx Y2 diode s flashing time the same as switch off time It gives an opportunity to distinguish selected co
27. is presented in the Annex A p A3 9 SOFTWARE INSTALLATION AND CHECKING OF CONNECTION 9 1 SOFTWARE INSTALLATION Application package supplied with the converter consists of Configuration application of the converter HUBC Configurator Tool for update firmware HUBC Flash Loader USB controller s driver of the converter Drivers directory Plugin for Raport 2 application HUBC Plugin in case of installed application Raport 2 Microsoft NET Framework 2 0 optional installation in case when it is not installed in the operating system To install software user should execute file Setup exe Window where Polish or English language of installation should be selected will be displayed gt Wybierz jezyk uzywany podczas instalacji TT p E 7 DTR HB 01 ENG Installation window will be displayed after clicking OK button f Setup HART USB Bluetooth Converter xj Welcome to the HART USB Bluetooth Converter Setup Wizard This will install HARTAJSB Bluetooth Converter on your computer It is recommended that you dose all other applications before continuing Click Next to continue or Cancel to exit Setup After pressing Next gt button user should select installation path N Setup HART USB Bluetooth Converter Select Destination Location Where should HART USB Bluetooth Converter be installed k Setup will install HART USB Bluetooth Converter into the following
28. nverter from others Switching off or reset of the converter results in switching off this mode Option USB Compliant switches on if selected compatibility of the converter with advanced USB functions such as possibility to negotiate higher supply current and reaction for hibernation of USB host It allows to e g charge converter s battery quicker Option Reverse CD Polarity switches on if selected reversion of CD signal Carrier Detect of serial port during transmission via USB User should switch on this option if program for communication used requires CD signal and is signaling no connection with this transmitter Some program for communication with transmitter with HART protocol can use this signal to confirm presence of HART carrier and to avoid collision with other devices transmitting to the transmitter Because in case of HART transmission signal CD has other reference to carrier presence than in case of classic modem transmission RS232 some programs interpret activity of CD signal inversely Discussed option if selected allows solving this problem In case when Raport 2 is used and HART carrier must be checked what means selection of classic HART Modem Plugin Check carrier option switch Reverse CD Polarity should be turned off Options Sensitivity and Output Gain allow to set HART receiver and an amplitude of output voltage HART The other settings than the standard one are helpful in very distu
29. on from the sleep mode to normal operation mode serial port will be U opened again During restart of the device user should not attempt to establish connection via Bluetooth Option Squawk is useful for signaling which converter is currently controlled in case of having many converters or Bluetooth devices A6 SUPPLY According to the p 11 of this manual Fully charged battery is enough for at least 8 hours of continuous operation in room temperature with Bluetooth transmission This time can be lengthen and depends on radio conditions distance between Bluetooth distances time intended for factual radio transmission as well as of type of cooperating Bluetooth module A7 CONFIGURATION OF CONVERTER CONNECTED VIA BLUETOOTH INTERFACE Configuration should be performed similarly as presented in p 12 of this manual for USB connection After starting of HUBC configurator application single window presented below will be opened 24 DTR HB 01 Zalacznik A COM Port comio Aplisens HUBCrev3 Aug 10 2012 Rev 0105 00 12 6f 23 82 84 Bluetooth 00000 Battery U Settings Time to Power Off Squawk USB Compliant Reverse CD Polarity In case of Bluetooth connection opening of the serial port is connected with establishing of 1 radio connection and can last for several seconds User should pay attention to the Status frame Information concerning added preambles
30. ow in system branch Ports during connection of the USB Bluetooth adapter to the computer Atleast one new serial port should be displayed as it is presented below 28 DTR HB 01 Zalacznik A Monitors Network adapters 422 Ports COM amp LPT 7 Port drukarki LPT1 72 Port komunikacyjny COM1 77 Standardowy port szeregowy przez cze Bluetooth 72 Standardowy port szeregowy przez cze Bluetooth 5 Processors Sound video and game controllers lt gt Storage controllers gt Detecting connected Bluetooth devices and checking whether device named Aplisens HUBC r3 is present Check in device properties which serial ports SPP Serial Port Profile are assigned to it as presented on the below figure ee ES lt Hardware and Sound Devices and Printers Bluetooth Devices 2 Aplisens HUBC r3 Properties Add a device Add a printer Remove device General Hardware Services Bluetooth 4 Devices 1 This Bluetooth device offers the following services To us service select the check box Bluetooth Services Z Serial port SPP SPP Aplisens HUBC r3 If there is no such device in the system user should search for new Bluetooth devices and add device with proper name to the system selecting option to manually enter pairing code which is 1234 see p A9 Software installation If detection of the device is impossible user
31. rbed environment or when connection with transmitter using standard sensitivity and amplitude values is impossible Sensitivity value Higher has a common meaning it indicates better sensitivity when weaker signal HART can be received Button Power Off results in immediate switching of converter to sleep mode Another switching on can be made only using button also in case of hibernation of the converter when there is no transmission Button Reset to defaults is used for immediate restart of the converter what is connected with loss of transmission for appox 30 seconds and deleting of all settings Next switching on can be made only when STAT diode will start to flash again what is an indication that restart is finished 12 2 CONVERTER CONFIGURATION VIA BLUETOOTH To make configuration during connection via Bluetooth user should proceed according to the annex A p A7 14 DTR HB 01 ENG 13 ESTABLISHING CONNECTION WITH TRANSMITTER WITH HART PROTOCOL 13 1 CONVERTER CONNECTED TO THE COMPUTER VIA USB Establishing connection with transmitter through a converter will be described on the example of Raport 2 application created by Aplisens S A To establish connection user should perform the following operations Connect HART cable to measuring loop of the transmitter on resistor s terminals Ro 22500 or in different way according to the user s manual of transmitter Switch on converter and make sure that ST
32. re this application is described in p 12 Configuration of the converter User should press button Read in the application s window User should check sensitivity and gain settings for HART signal and set Input sensitivity Standard Output gain High Check correctness of HART circuit Check whether transmitter is supplied and operational and whether HART cable is not damaged If connection still cannot be established user should contact service 17 DTR HB 01 ENG 15 MAINTENANCE SPARE PARTS Dirt formed should be removed with damp soft cloth Do not rub enclosure through when it is dry Converter s components which can be worn USB cable and HART communication cable 16 PACKING STORAGE AND TRANSPORT Converters should be packed in such way that they are protected against damaging during transport in unit and or omnibus packages or together with other products from Aplisens S A It should be stored in packagings in covered room free from vapours and aggressive substances in conditions conforming these given in p 5 2 allowable ambient and operation parameters Storage conditions the same as in case of computer and peripheral devices 17 WARRANTY The manufactures warrants correct operation of the converters for 36 months 12 months for battery from the date of purchase as well as warranty and post warranty service General warranty conditions are presented on the manufacturer s website www aplisens pl in tab
33. s Name HUBCrev3 Read Date 14 2012 Rev 0104 Bluetooth ID 00 12 6f 23 8b de Communication via USB Disconnect USB cable and make sure that STAT diode is flashing Proceed to searching for Bluetooth devices e f many converters Aplisens HUBC r3 were detected than user can preview it unique address in properties of each device and then compare it with the noted one Example of detection of other incompatible address is presented below 30 DTR HB 01 1 2 Aplisens HUBC 13 Properties 000 Zalacznik 1 Aplisens HUBC 3 Device Information Manufacturer Unavailable Model Unavailable Model number Unavailable Categories Other Transport Bluetooth Webpage Unavailable Troubleshooting Information Connection Standard Last connected Friday 11 May 2012 Serial number Unavailable MAC address Unavailable Unique identifier IP address Unavailable As it can be seen checked converter is not the one which was connected via USB cable Check next detected converter and if the ID is compatible assign it to the computer
34. t and send it for repair to the manufacturer or to a firm authorized by the manufacturer In order to minimize the risk of malfunction and associated risks to staff the device is not to be installed or used in particularly unfavourable conditions where the following dangers occur possibility of mechanical impacts excessive shocks and vibration excessive temperature fluctuation condensation of water vapour dust icing Changes in the production of transmitters may precede a paper updating for the user the current user manuals are available at http www aplisens pl 1 DTR HB 01 ENG SPIS TRESC INTRODUCTION USER MATERIALS APPLICATIONS AND MAIN FEATURES IDENTIFICATION MARKING METHOD OF MARKING DURING ORDERING TECHNICAL DATA 5 1 HARDWARE REQUIREMENTS 5 2 ALLOWABLE AMBIENT AND OPERATION PARAMETERS 5 3 OPERATIONAL PARAMETERS 5 4 PERMITTED ENVIRONMENTAL CONDITIONS CONSTRUCTION LOCATION OF CONVERTERS INSTALLATION WIRE CONNECTION USING USB CABLE SOFTWARE INSTALLATION AND CHECKING OF CONNECTION 9 1 SOFTWARE INSTALLATION 9 2 CHECKING OF CONNECTION THROUGH USB CABLE 10 BUTTONS AND LED DIODES 11 SUPPLY 11 1 CHARGING CURRENT 11 2 TOOL INTENDED FOR CHARGING 11 3 INFEVENCE OF TEMPERATURE ON SUP PLY n u uu u asua iria 11 4 INFLUENCE OF BATTERY CHARGING ON OPERATION OF THE CONVERTER CHARGING TIME 11 5 SIGNALING OF CHARGING STATES 12 CONVERTER CONFIGURAT
35. ted on the below figure Transmitter Power with HART Ro2202 supply eg HART 89 25 2 I connecting cable HART USB A V Bluetooth Converter Hong gt y E UNIVERSAL SERIAL BUS e Bluetooth x k lt Es Rys A1 Example of connection with computer devices via Bluetooth Connection should be established according to the User s Manual of the transmitter with Hart protocol 19 DTR HB 01 Zalacznik A lt Converter has set of internal commands enabling to exchange data between it computer without connection of the transmitter It allows to simultaneously check connection of the converter with computer without connected HART circuit In given moment the converter can operate on one transmission channel via USB or via Bluetooth If converter is connected to USB port in the computer establishing of Bluetooth 1 connection is not possible Bluetooth module is disconnected and relevant serial port is inactive In case of connection to the USB charger Bluetooth connection can be established Provided application HUBC Configurator is intended for configuration of the converter This application can be also used for quick confirmation of the communication For communication with HART transmitters through the converter any software dedicated for this purpose can be used Converter s manufacturer recommends using Raport 2 application A4
36. the functioning of converters and how to operate them It includes essential recommendations concerning installation and use as well as emergency procedures 1 2 Converters fulfill the requirements of the Directive 2004 108 EC according to the marking on plate and to the relevant Declaration of Conformity 1 3 In case of use of wireless communication through the Bluetooth interface also information contained in the Annex A to this manual should be taken into account 2 USER MATERIALS Buyers receive devices in unit packages or packed together with other devices manufactured by Aplisens S A User will get together with the converter with internal battery a Communication cable HART enabling connection of the converter to pressure and temperature transmitter b USB cable enabling connection of the converter with computer or charger equipped with the USB connector c External adapter USB Bluetooth with installation software d Software installation version with electronic User s Manual on CD e Product certificate which is also a warranty card f Declaration of Conformity EC on request g User s Manual marked as DTR HB 01 ENG Items d f g are available on the website www aplisens pl 3 APPLICATIONS AND MAIN FEATURES 3 1 Converter is intended for communication with components of the automatics system equipped with HART interface wired with computer equipped with USB connector wireless with
37. y for normal operation of the device therefore button s socket in the enclosure is formed in such way that accidently pressing of it is very difficult STAT diode is signaling state of the converter while BATT diode state of internal rechargeable battery 7 LOCATION OF CONVERTERS INSTALLATION This converter is intended for used in rooms with conditions described in p 5 2 8 WIRE CONNECTION USING USB CABLE Method of connection of the converter to the transmitter and to computer is presented on the figure Ro gt 2500 HART connection cable Ver UNIVERSAL SERIAL BUS Fig 2 Example of connection with the computers using USB 6 DTR HB 01 ENG Connection of the converter with transmitter should be realized according to the User s Manual of this 1 transmitter Converter has a set of internal commands enabling to exchange data between it and computer without connection of the transmitter It allows checking connection of the converter with computer without 1 connected HART circuit Provided application HUBC Configurator is intended for configuration of the converter This application can be also used for quick confirmation of the communication For communication with HART transmitters through the converter any software dedicated for this purpose can be used Converter s manufacturer recommends using Raport 2 application Wireless connection of the converter using Bluetooth
Download Pdf Manuals
Related Search