Home

User`s Manual

1. OOOO 15 1 57 51 Pin No Signal name Pin No Signal name PC1 N C 51 GND PC2 N C 82 TX PC3 N C S3 TX PC4 GND S4 GND PC5 GND S5 RX PC6 GND S6 PC7 5V 57 GND PC8 5V PC9 5V 10 GND 11 12 PC13 12V PC14 12V PC15 12V CONTEC PT S1000 User s manual 33 4 Each Component Function CONTEC 34 PT S1000 User s manual 5 BIOS Setup 5 BIOS Setup Introduction This chapter discusses American Megatrends Inc s Setup program built into the FLASH ROM BIOS The Setup program allows users to modify the basic system configuration This special information is then stored in FLASH ROM so that it retains the Setup information when the power is turned off The rest of this chapter is intended to guide you through the process of configuring your system using Setup Starting Setup The BIOS is immediately activated when you first power on the computer The BIOS reads the system information contained in the FLASH ROM and begins the process of checking out the system and configuring it When it finishes the BIOS will seek an operating system on one of the disks and then launch and turn control over to the operating system While the BIOS are in control the Setup program can be activated in one of two ways 1 By pressing Del or F2 immediately after switching the system on 2 By pressing the Del or F2 key when t
2. Ver 2 14 1219 Copyright C 2 Figure 5 7 PCH FW Configuration CONTEC PT S1000 User s manual 45 5 BIOS Setup AMT Configuration Use this menu to specify the Intel amp Active Management Technology configuration Setup Utility Copyright C 2011 Ar can Megatrends Inc Advanced Intel AMT Enabled Enable Disable Intel amp Un Configure ME Disabled Active Management Technology BIOS Extension Note iAMT H W is always enabled This option just controls the BIOS extension execution If enabled this requires additional firmware in the SPI device Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C 2011 American Megatrends Inc Figure 5 8 AMT Configuration Items that can be configured for AMT Configuration are described in the table below Table 5 7 AMT Configuraiton Explanation Enable Disable Intel Active Management Technology BIOS Extension Note that 1 H W is always enabled Disabled Enable This option just controls the BIOS extension execution Un Confi ME iDisabled Un Configure ME without password when bid Enabled Enabled CONTEC 46 PT S1000 User s manual 5 BIOS Setup USB Configuration up Utility Copyright 2 gatrends Inc Advanced USB Configuration Enabl
3. Register dedicated to write transmitted data to R Reciever Buffer Register DLAB O D7 06 D5 D4 D3 D2 bit7 MSB DO bitO LSB D1 Register dedicated to read received data from DLL Divisor Latch LSB DLAB 1 06 D5 D4 D2 bit7 MSB DO bitO LSB D1 Baud rate setting register LSB DLAB 1 D3 12 DLH Divisor Latch MSB D7 D6 D5 D4 bit7 MSB DO bitO LSB D1 Baud rate setting register MSB e Register DLAB 0 D2 DI IER Interrupt Enab D5 0 0 0 0 EMS ELSIETHREI ERDAI _ Received data Interrupt enable L_ Received data register empty Interrupt enable Receiver line status Interrupt enable status interrupt enable Always used at 0 1 Enable interrupt 0 Disable interrupt CONTEC 80 PT S1000 User s manual Table 6 6 Function of Each Register 2 4 I O address Description 03FAH IIR Interrupt D7 D6 dentification Register D D4 D2 DO 0 0 0 0 0 Interrupt details Ls 1 Do not generate interrupts 0 Generate interrupts Priority Description 1 Interrupts are not generated 0 1 high Generated by overrun parity framing error or break interrupt Cleared whe
4. SYS Smart Fan Mode System Smart Fan Mode Thermal Cruise Mode elect System Fan expect PWM Output DC Voltage Value 70 255 Note This item can setting only when SYS Smart Fan Mode Manual Mode SYSFAN expect PWM Output DC Voltage Select System Fan Target Temperature Value 1 127 SYSFAN Target Temperature Note This item can setting only when SYS Smart Fan Mode Thermal Cruise Mode Select System Fan Tolerance of Target Temperature SYSFAN Tolerance of 5 Value 1 15 Target Temperature 5 Note This item can setting only when SYS Smart Fan Mode Thermal Cruise Mode Select System Fan StartUP Stop Value Value 1 255 Note This item can setting only when SYS Smart Fan Mode Thermal Cruise Mode Manual CPU Smart Fan Mode N CPU Smart Fan Mode Thermal Cruise Mode ect CPU Fan expect PWM Output DC SYSFAN StartUp Stop Value tage Value 70 255 CPU expect PWM Output DC Voltage Note This item can setting only when CPU Smart Fan Mode Manual Mode Select CPU Fan Target Temperature Value 1 127 CPU Target Temperature 50 suni vat Note This item can setting only when CPU Smart Fan Mode Thermal Cruise Mode Select CPU Fan Tolerance of Target Temperature Value 1 15 Note This item can setting only when CPU Smart Fan Mode Thermal Cruise Mode Select CPU
5. CAUTION A board that uses the back of the board edge connector the shaded area in the figure may not be mounted The PCI bus slot is for 32 bit Operational tests are not performed for the dual purpose boards for 64bit 32bit such as ADAPTEC 39160SCSI board or Intel Pro1000 MT network board PT S1000 User s manual 29 4 Each Component Function DVI D Interface DVI D A DVI D interface is provided You can use it to connect a digital type monitor The connector is named DVI DVI I 29 pin connector CAUTION Analog RGB signal is not provided Table 4 12 DVI Connector Connector used on DVI I 29 pin the product 1 8 Cl C2 C5 aS a 9 17 2 Pin No Signal Pin No Signal Pin No Signal name name name DATA2 13 N C C1 N C DATA2 14 5V C2 N C DATA2 3 San 15 GND N C 4 N C 16 HPD C4 N C 5 N C 17 DATAO C5 GND 6 DDC CLK 18 DATAO DDC m DATAO DATA SHIELD 8 N C 20 N C 9 DATAT 21 N C DATAO 10 DATA14 22 11 SUID 23 CLK 12 N C 24 CLK Display driver Install the appropriate display driver for your OS from the CONTEC s Web site CONTEC 30 PT S1000 User s manual 4 Each Component Function Display Interface VGA Connector for display connection is provided
6. 3 Hardware Setup Distances between this product and its vicinity 50mm or more ne 50m bL 40mm or mpre orjmore d A Somm N Installation panel Figure 3 9 Distances between this product and its vicinity CAUTION Do not install this product into the fully sealed space except the case in which the internal temperature is adjustable by equipment such as air conditioner Troubles such as operational malfunctions could be occurred by the temperature increase caused by long term usage Ambient temperature In this product the ambient temperature is decided from the multiple measurement points as shown below When making use of the product the air current should be adjusted to prevent that all the temperatures measured at the measurement points exceed the specified temperature Installation panel Figure 3 10 Measurement points of ambient temperature CONTEC 18 PT S1000 User s manual 3 Hardware Setup PCI Card Installation 1 Be sure the power is turned off 2 Remove the top cover Figure 3 11 Remove the top cover 3 Remove the brace base with PCI card brace Figure 3 12 Remove the brace base with PCI card brace PT S1000 User s manual 19 3 Hardware Setup 4 Let brace base and PCI card brac
7. Intel R xxxx TM CPU xxxx CPU x xxGHz CPU Signature Microcode Patch Max CPU Speed Min CPU Speed CPU Speed Processor Cores Intel HT Technology Intel VT x Technology Intel SMX Technology 64 bit L1 Data Cache L1 Code Cache L2 Cache L3 Cache xx kB x X xx kBx X xx kB x X xxxx kB Hyper Threading Enabled Enabled for Windows XP and Linux OS optimized for Hyper Threading Technology and Disabled for other OS OS not optimized for Hyper Threading Technology When Disabled only one thread per enabled core is enabled e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Active Processor Cores All Intel Virtualization Technology Disabled Figure 5 5 CPU Configuration Items that can be configured for CPU Configuration are described in the table below There items are not displayed when using non supported CPUs Table 5 5 CPU Configuraiton Explanation Enabled for Windows XP and Linux OS optimized for Hyper Threading Technology and Disabled for other OS OS not optimized for Hyper Threading Technology Hyper Threading i Number of cores to enable in eache Active Processor Cores processor package When enabled a VMM can utilize the Disabled Enabled Intel Virtualization additional hardware capabilities provided Technology b
8. e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Figure 5 16 Smart Fan menu Items that can be configured for Smart Fan Configuration are described in the table below Table 5 14 Smart Fan Configuration Explanation Disabled Smart Fan Function Enable or Disable Smart Fan function The following sub items are available Smart Fan Mode Configuration Use this menu to specify the Mode of Smart Fan CONTEC 54 PT S1000 User s manual 5 BIOS Setup Smart Fan Mode Configuration Use this menu to specify Smart Fan Mode settings up Utility Copyright C 2011 American Megatrends Inc Advanced Smart Fan Mode Configuration SYS Smart Fan Mode Select SYS Smart Fan Mode Manual Mode SYSFAN expect PWM Output DC Voltag 255 CPU Smart Fan Mode Manual Mode CPUFAN expect PWM Output DC Voltag 255 e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C 2 Figure 5 17 Smart Fan Mode Configuration menu Items that can be configured for Smart Fan Mode Configuration are described in the table below CONTEC PT S1000 User s manual 55 5 BIOS Setup Table 5 15 Smart Fan Mode Configuration Explanation Manual
9. Exit Ver 2 14 1219 Copyright C Figure 5 10 Super I O Configuration Items that can be configured for Super I O Configuration are described in the table below Table 5 9 Super I O Configuration Explanation Enabled Enable or Disable Resume on PS2 Keyboard Resume on PS2 KB MS Disabled and Mouse function Enabled Enable or Disable Watch Dog Timer Watch Dog Timer Disabled function Watch Dog Timer Count Second Select Watch Dog Timer s Mode Mode Minute Mode Watch Dog Timer Time Select Watch Dog Timer s Time out value out Value Value 1 255 The following sub items are available Serial Port x Configuration x 1 4 Use this menu to specify settings for serial ports 1 to 4 CONTEC 48 PT S1000 User s manual 5 BIOS Setup Serial Port 1 Configuration ip Utility Copyright C Advanced Serial Port 1 Configuration Enable or Disable Serial Port COM Serial Port Enabled Device Settings IO 260h IRQ 11 Change Settings Auto e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C 11 American Megatrends Inc Figure 5 11 Serial Port 1 Configuration Items that can be configured for Serial Port 1 Configuration are described in the table below Table 5 10 Serial Port 1 Con
10. 13 bytes 32 bytes i 1 2 ytes Interrupt controller ytes ytes ytes ytes ytes ytes ytes ytes ytes ytes ytes yte byte yte yte yte bytes ytes byte ytes ytes ytes ytes ytes ytes bytes ytes ytes ytes bytes byte ytes ytes b ytes ytes ytes ytes ytes bytes ytes CONTEC PT S1000 User s manual 74 6 Appendix Table 6 2 Port Addresses 2 2 Description IDE SATA controller PCI 03 8 4 0400 043F 64 bytes Power management 0400 04D1 Interrupt controller 0500 053F 64 bytes GPIO Reserved Reset Generator 0000 OFFFF 62208 bytes PCI Bus Interrupt Level List Table 6 3 Hardware Interrupt Levels Factory Settings wa wok mas 1 wm ma jme ms Slave me mar emma man I mar 1 mew mars m mare 79m ras serien omn ms lt een ms 1 mea ma ma tow m CONTEC PT S1000 User s manual 75 6 Appendix POST Codes Table 6 4 POST Codes 1 3 POST thes lt Security SEC phase gt m Power on Reset ype detection oftware hardwar 71 AP initialization a
11. Advanced 39 PCI Subsystem Seting S 41 egent 42 43 SATA Configuration ERE 44 PCH EW Configur tion 202 ERE RENTRER 45 46 USB Configuration uon tu e t n REED EUR MEE NRI RESTER Si Han 47 S per VO Configuratio reesei ertt ER ERI RR eet ERE e e ke 48 Serial Port I Configuration 2 o ee eve e e m PRU E RR P nts 49 Serial Port 2 eese e eee Rn Runen 50 Serial Port 3 Configuratioti Jesolo E eed 51 Serial Port 4 COnfIgUratlofi eerte e tt ERR 52 H W Monitor Start 54 CONTEC iv PT S1000 User s manual Smart Fan Mode Configuration aeree e ene IN A een ER EA SERE CREER a 55 Option Rom Policy iE EEUU DIEN EGER SEEN ENERO 57 CPU PPM Configuration EEE AE ee tea ee ted epe ttd 58 Chipset iss PCEFIO Configuration E E E 5 PCH Azalia Configurat
12. Connector name is VGA HD SUB 15P Table 4 13 Display Connector 6 _L_N0 4 40UNC Inch screw threads 5 11 s omes Ds we oes s ome Dos os ome Do o Display driver Install the appropriate display driver for your OS from the CONTEC s Web site PT S1000 User s manual 31 4 Each Component Function HDMI Interface HDMI HDMI interface is provided You can use it to connect digital type monitor The connector is named HDMI HDMI 19 pin connector Table 4 14 HDMI Connector Connector used on HDMI 19 pin the product 19 1 18 2 Pin No Signal Pin No Signal name name CLK 1 DATA2 11 SHIELD DATA2 2 SHIELD 12 CLK 3 DATA2 13 GND 4 1 14 N C 5 SHIELD 15 SCL 6 DATAI 16 SDA 7 DATAO 17 GND DATAO 8 SHIELD 18 5V 9 DATAO 19 HPD 10 CLK Display driver Install the appropriate display driver for your OS from the CONTEC s Web site 32 CONTEC PT S1000 User s manual 4 Each Component Function Serial ATA S ATA It has serial ATA 3 0 compliant controller 2 5 inch SATA HDD can be connected to an onboard connector Table 4 15 SATA Connector Connector used SATA connector on the product
13. I O Port Addresses for more information on I O address and register function Serial D additionaly support RS422 485 Please change jumper settings according to next section when you use RS422 485 Table 4 8 SERIAL A B C D VO Addresses and Interrupts omm Table 4 9 Serial Port A B C Connector Connector used on the 9 pin D SUB MALE product 1 No 4 40UNC 5 Inch screw goce 6 9 s s pee s es pene s om nme PT S1000 User s manual 27 4 Each Component Function Table 4 10 Serial Port D Connector Connector used on 9 pin D SUB MALE the product 1 No 4 40UNC Inch screw RAD B sca 6 9 pese 3 om e pe RS 422 RS 485 specifications Serial port D Transmission method RS 422 RS 485 compliant asynchronous serial transmission Baud rate 50 to 115 200bps programmable Signal extensible distance 1 2km Max Termination 1200hm Table 4 11 Serial D jumper settings v mn 5 2 6 JP3 1 5 CONTEC 28 PT S1000 User s manual 4 Each Component Function Expansion slots It has two expansion slots for the implementation of PCI bus type borad Board Dimensions Allowed 185 Max lt gt 107 Max mm PCI bus board Figure 4 3 Expansion Board Dimensions
14. MERE Eee NOR 24 LED POWER HDD WE Ue DN an D SERA NITET 24 DC Power Input Connector DEIN eroe a Eco eh ie M a eee RE EU nado 24 Power switch POWER SW DAC REESE HERES ENTE REUS SURE 25 5 5 REDE Line Interface LINE O e Line in Interface EINE IN 5 5 b cadens eere tiir e Micandntertace eee een te eve E EE E USB 3 0 Potts SB 3 0 eret E ERE Le ES 25 USB 2 0 Ports USB 2 0 ED mu miss an 25 Giga bit Ethernet LAN 26 Serial Port Interface SERIAL A D nennen usa nen 27 Expansion 29 DVED Interface ionic riti re PEU EXER SIS EH TER 30 Display 31 HDMI Interface man ms 32 Semnal ATA SATA testen 33 3 BIOS SETUP 35 Introduction OU ATR 35 e en HO Ge PEREGIT EE Using SetiD D MR Getting Help Main Menu cie re oe eU e ec bye 37 Setup Items ann an isn VER EROR ERRARE MEN RE 37 luu Q 38
15. MINI DIN connector for PS 2 keyboard mouse Table 4 6 PS 2 Connector NENNEN ee Giga bit Ethernet LAN A B This product is equipped with 2 pus for giga bit Network type 1000BASE T 100BASE TX IOBASE T Transmission speed 1000M 100M 10M bps Max network path length 100m segment Controller 82579LM LAN A 82583V LAN B Table 4 7 Giga bit Ethernet Connector Pin No ome LEDs for display of network statuses Right LED Link LED Normal connection Green ON Operation Green Blinking Left LED Operation LED 10M Off 100M Green 1000M Orange LAN drivers Install the appropriate LAN driver for your OS from the CONTEC s Web site AN CAUTION If you want to use WOL function please select Enable at the item Enable PME of OS driver setting CONTEC 26 PT S1000 User s manual 4 Each Component Function Serial Port Interface SERIAL A D SERIAL A B C D The product has 4 ports of RS 232C compliant serial ports supporting up to a baud rate of 115 200bps with a 16 byte transmission dedicated data buffer and a 16 byte reception dedicated data buffer You can use Chapter 5 BIOS Setup to configure an I O address interrupt and unused state for each of the ports independently The same I O address and IRQ cannot be shared with any other device Please refer to Chapter 6
16. Securit Save amp Exit Save Changes and Exit Exit system setup after saving Discard Changes and Exit the changes Save Changes and Reset Restore Defaults Boot Override e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C 2011 American Megatrends Inc Figure 5 31 Save amp Exit menu The following items are available Save Changes and Exit Pressing Enter key shows confirmation dialog box and shows the message below Save amp Exit Setup Save configuration and exit Nol Pressing Yes saves any changes made in FLASH ROM and then restarts the system or continues to boot as necessary The next time the computer is booted the BIOS configures the system based on the configuration stored in FLASH ROM Pressing No lets you go back to setup menu CONTEC PT S1000 User s manual 71 5 BIOS Setup Discard Changes and Exit Pressing Enter key shows confirmation dialog box and shows the message below Exit Without Saving Quit without saving No Pressing Yes continues to boot the system without saving any changes made in FLASH ROM Pressing No lets you go back to setup menu without storing it in FLASH ROM Save Changes and Reset Pressing lt Enter gt key shows confirmation dialog box and shows the message below Save conf
17. dee ERREH 2 How ome pp eee pee eai ase nahe a re ea a 2 Liability E M 2 Safety Precautions SERT 3 Safety Informati n EA 3 Caut Oi E 3 2 SYSTEM REFERENCE 7 Speci CaN u eeesdeodts 7 Power Management Features unse cone pe AE eti de 1 Power Requirements tet e Re CU E DER 11 Power Consumption Ane De Ee VENERE ER ees wee 11 Physical Dimensions 5 5 enti HORE ER ENTER E Ee e 12 3 HARDWARE SETUP 13 Before Using the Product for the First 13 Hardware Setup unes e RERO ERE eee 14 Attaching the HDD eri E 14 Attaching the BG eee te Re MERE RAE NUR 15 Fastening the Cable 15 Hardware 16 Installation Requirements seite n 17 PGI Card Installationen ea pr OR LE ln Ee 19 Replace Fan nis DERNIER Drehen 22 Replace Filter tp CERE EP CUTE ERR CUERO 22 4 EACH COMPONENT FUNCTION 23 PT S1000 User s manual iii Component Nate ad te RIEN 23 Component Function er REED IGNOTUS
18. detailed function available for your system Chipset Use this menu to specify settings related to the chipset used Boot Use this menu to specify the boot settings Security Use this menu to change password to protect the security of your system Save amp Exit Use this menu to load save the setting or to exit the setup menu CONTEC PT S1000 User s manual 87 5 BIOS Setup Main Use this menu to check basic system configuration Settings that can be configured in the Main menu are described in the table below Table 5 2 Main Menu Display only General Description Explanation Set th tem date The day of thi ki System Date Month Day Year et the sys em ate The day of the week is set automatically System Time Hour Minute Second Set the system time Display access permissions for the current Access Level Administrator setup Items that can be configured depend on access permissions CONTEC 38 PT S1000 User s manual 5 BIOS Setup Advanced You can set the detailed function of system Following items are available Advanced PCI Subsystem Settings PCI PCI X and PCI Express ACPI Settings Settings CPU Configuration SATA Configuration PCH FW Configuration AMT Configuration USB Configuration Super IO Configuration H W Monitor Option Rom Policy CPU PPM Configuration gt gt gt gt gt gt gt e Select Screen T Select Ite
19. end we strongly recommend that you avoid making any changes to the chipset defaults These defaults have been carefully chosen by both AMI and your systems manufacturer to provide the absolute maximum performance and reliability If chipset settings are changed even slightly it may become necessary to repair the unit A Final Note about Setup The information in this chapter is subject to change without notice CONTEC 36 PT S1000 User s manual 5 BIOS Setup Main Menu Once you enter the AMI BIOS Setup Utility the Main Menu will appear on the screen Use the arrow keys to select among the items and press Enter to accept and enter the sub menu BIOS Information Set the Date Use Tab to BIOS Vendor American Megatrends Switch between Date elements Core Version 4 6 5 3 Compliency UEFI 2 3 PI 1 2 Project Type PT S1000xx Series Project Version QM77xxxx Build Date and Time MM DD YYYY HH MM SS System Date Sun MM DD YYYY System Time HH MM SS Access Level Administrator e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C 20 merican Megatrends Inc Figure 5 1 Main Manu Setup Items The main menu includes the following main setup categories Main Use this menu to check basic system configuration and to change system date Advanced Use this menu to set
20. manual 1 Introduction 2 5 inch HDD slot does not support hot plugging 2 5 inch HDD cannot be removed or inserted while the power is on Do not remove or install 2 5 inch HDD or connect to 2 5 inch HDDs while the unit is turned on This product may malfunction or cause a failure Component Life 1 Battery The internal calendar clock and CMOS RAM are backed by a Lithium primary battery The backup time at a temperature of 25 C with the power disconnected is 7 years or more 2 Touch panel operating lifetime of the touch panel is at least 36 millions touches as tested by mechanical touching under 250g of force at a rate of two presses per second 3 LCD backlight Display brightness decreases over time with use The operating lifetime of the backlight is 50 000 hours the time until the brightness is lowered to 50 of the initial value 4 CPU Fan 50 000h 40 5 System Fan 110 000h 40 Replacement of expendables is handled as a repair there will be a charge Component life is not guaranteed value but only referential value FCC PART 15 Class A Notice NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in commercial environment This equipment generates uses and can radiate
21. 0 User s manual 4 Each Component Function 4 Each Component Function Component Name Front view Bottom view SERIALA SERIAL SERIAL SERIAL D RESET VGA USB2 0 LANA LANB POWER LE ao NER EA sLor1 HDD LED J store oe ien s 5 gu Power su 8 EDER 2 LINE IN Q USB 3 0 LINE OUT DVI HDMH ie Figure 4 1 Component Name Table 4 1 Component Function Name Function Slot 1 2 CONTEC PT S1000 User s manual 23 4 Each Component Function Component Function LED POWER HDD There are 2 LEDs in front of this product Table 4 2 Display Contents of LED POWER LED Indicates that this product is switched off ON Green Indicates that this product is switched on HDD LED ON Orange Indicates that the HDD device is being accessed DC Power Input Connector DC IN To supply the power always use the power supply listed below Rated input voltage 12 24VDC Range of input voltage 10 8 31 2VDC Power capacity 12V 16 1A or more 24V 7 9A or more Table 4 3 DC Power Connector Connector type 9360 04P mfd by ALEX Pin No Signal name 4 3 1 GND 2 GND 2 i 3 12 24V 4 12 24V Applicable con
22. 7 9A Max Expansion board 12V 1A power supply 5V 2A capacity 3 3V 1A 12V 0 5A 5V Not supplied External device USB2 0 5 1 0 500mA x 2 power supply USB3 0 5V 3 6A 900mA x 4 capacity CONTEC 8 PT S1000 User s manual 2 System Reference Table2 3 Installation Environment Requirements PT S1000HXP2 DC7000 Model COPS 1000XSXP2 DCTONN 0 50 C 0 45 C when using 1000BASE T ren T refer to ee 3 Installation Requirements for required conditions Operating temperature Storage temperature temperature 10 S O Signal line 1kV IEC61000 4 4 Level 3 EN61000 4 4 Level 3 resistance PIRE Contact discharge 4kV TEC61000 4 2 Level 2 EN61000 4 2 Level 2 lectricit ET Atmospheric discharge 8kV IEC61000 4 2 Level 3 EN61000 4 2 Level 3 Noise resistance When HDD is turned on 10 50Hz 0 5G 25 min each in x y and z directions JIS C60068 2 6 compliant IEC60068 2 6 compliant When HDD is turned off 10 57Hz semiramplitude 0 15 mm 57 150Hz 1 5G 40 min each in x y and z directions JIS C 60028 2 6 compliant IEC 60068 2 6 compliant I m 10G half sine shock for 11 ms in x y and z directions ET JIS C60068 2 27 compliant IEC68 2 27 compliant Class D grounding SG FG continuity Vibration Sweep resistance resistance CONTEC PT S1000 User s manual 9 2 System Reference Table 2 4 Display Optical Specificati
23. Aptio Setup Utility Copyright C 2011 American M Advanced CPU PPM Configuration Enable Disable Intel SpeedStep EIST Disabled CPU C3 Report Disabled CPU C6 report Disabled CPU C7 report Disabled e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C 2011 American Megatrends Inc Figure 5 19 CPU PPM Configuration menu Items that can be configured for CPU PPM Configurations are described in the table below Table 5 17 CPU PPM Configuration Disabled EIST Enable or Disable Intel SpeedStep Enabled Disabled Enable or Disable CPU C3 ACPI C2 report PU C3 R t Enabled to OS CPU report Disabled Enable or Disable CPU C6 ACPI C3 report Enabled to OS CPU C7 report Disabled Enable or Disable CPU C7 ACPI C3 report Enabled to OS CONTEC 58 PT S1000 User s manual 5 BIOS Setup Chipset Use this menu to specify chipset settings American Megatrends Inc gt PCH IO Configuration PCH Parameters gt System Agent SA Configuration e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C 2011 American Megatrends Inc Figure 5 20 Chipset m
24. C7000 17 inch touch panel LCD SXGA Memory 4GB 2 PCI slots Option CPU OS 2 5 inch HDD Power supply Features Based on Ivy Bridge branded as 3 Generation Intel Core Processors The platform with higher performance provides further experience against heavy CPU loading for various industrial scenes CONTEC s reliable design Industrial design contributes to various uses under severe conditions such as high temperature 50 low temperature 09 vibration 1 5G and shock 106 Remote power management function to reduce operation tasks This product supports remote wake up by LAN or Serial It provides your system with high usability under your own network Rich interfaces USB3 0x4 USB2 0x2 1000BASE T x 2 Serial x 4 DVI D VGA HDMI Audio 2 5 inch SATA drive bay PCIx2 A wide range of power supplies It can be used in a variety of power environments 10 8 31 2VDC Touch panel enables keyboard less operation These products have analog touch panel enabling mouse emulation using driver software Supported OS Windows 7 Professional PT S1000 User s manual 1 Introduction Customer Support CONTEC provides the following support services for you to use CONTEC products more efficiently and comfortably Web Site Japanese _ http www contec co jp English http www contec com Chinese http www contec com cn Latest product information CONTEC provides u
25. CPU DXE initialization is started ah CONTEC 76 PT S1000 User s manual 6 6 6 Appendix Table 6 4 POST Codes 2 3 73h 7Th T8h 79h TAh 7Fh 80h 8Fh 90h 91h Driver connecting is started 92h PCI Bus initialization is started 93h PCI Bus Hot Plug Controller Initialization 94h PCI Bus Enumeration 95h 96h 97h 98h 99h 9Ah 9Bh 9Ch USBDetet 2 un vs amp 9D 9Eh 9Fh Oh h 2h Adh Abh 6h ATh h h h h h gt gt gt gt un gt an un gt h h h h h B3h w VANS 63 55 zj vel B4h B h B6h BTh B8h BFh COh CFh OEM BDS initialization codes CONTEC PT S1000 User s manual 77 6 Appendix Table 6 4 POST Codes 3 3 ACPI ASL Checkpoints CONTEC 78 PT S1000 User s manual 6 Appendix SERIAL I O Address and Register Function The following table lists the I O addresses in case of SERIAL D Table 6 5 VO Address Read Write Register 03 Transmitter holding register ww son DLAB Divisor Latch Access Bit The value in bit 7 of the line control register CONTEC PT S1000 User s manual 79 6 Appendix Table 6 6 Function of Each Register 7 4 I O address Description Register DLAB 0 D2 DI 03F8H THR Transmitter Holding D7 D6 D5 D4 bit7 MSB DO bitO LSB
26. Fan StartUP Stop Value Value 1 255 CPU Tolerance of Target Temperature CPU StartUp Stop Value Note This item can setting only when CPU Smart Fan Mode Thermal Cruise Mode CONTEC 56 PT S1000 User s manual 5 BIOS Setup Option Rom Policy Use this menu to specify Option Rom Policy settings up Utility Copyright C 2011 American Megatrends Inc Advanced Boot option filter UEFI and Legacy This option controls what Launch PXE OpROM policy Disabled devices system can boot to Launch Storage OpROM policy Legacy only e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C 2 Figure 5 18 Option Rom Policy menu Items that can be configured for Option Rom Policies are described in the table below Table 5 16 Option Rom Policy Explanation and Legac Boot option filter Legacy only UEFI only This option controls what devices system can boot to Launch PXE OpROM Disabled Controls the execution of UEFI and Legacy policy Enabled PXE OpROM Do not le h Launch Strage OpROM HE ne Controls the execution of UEFI and Legacy UEFI only policy Strage OpROM CONTEC PT S1000 User s manual 57 5 BIOS Setup CPU PPM Configuration Use this menu to specify CPU PPM Configurations
27. IPC Series PANEL PC 51000 Series Core 17 DC input 15 XGA PCI x 2 17 SXGA PCI 2 User s Manual CONTEC CO LTD Check Your Package Thank you for purchasing the CONTEC product The product consists of the items listed below Check with the following list that your package is complete If you discover damaged or missing items contact your retailer If you use driver amp utility software set download it form the CONTEC s Web site Product Configuration List Model Name PanelSize Memory CPU Storage 05 Slot A PT S1000HXP2 DC7000 15 4GB Option Option Option PCI x 2 T PT SIBDOXSXP DCTOOD Configuration A TA Name m Name Ree Pe Meme dS Screws tofinslotcover 6 2 Waterprootpacking 1 IBetewe _ 31 Number Tab 1 0 installed 8 Power supply connector set Warranty at Certificate 09 Precaution Product e xo P x4 List Guide m 2 If you need product manual driver amp utility software set download it form the CONTEC s Web site PT S1000 User s manual i Copyright Copyright 2014 CONTEC Co Ltd Rights Reserved No part of this document ma
28. LY the User s password is set then this is a power on password and must be entered to boot or enter Setup In Setup the User will have Administrator rights The password length must be in the following range Minimum length Select Screen Maximum length T Select Item Enter Select Change Opt Administrator Password F1 General Help User Password F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit American Megatrend Figure 5 30 Security menu The following items are available Administrator Password Press Enter key to input password as follows Create New Password 8 Confirm New Password Enter a password of between 3 and 20 characters twice If you want to disable password enter the input menu of Administrator Password again Enter Current Password Create New Password Confirm New Password If you input current password to the first form and input no characters to the second and the third form password will be disabled User Password Press Enter key to input password as follows Create New Password 8 Confirm New Password ERES Enter a password of between 3 and 20 characters twice The procedure for disabling the password is the same as that for the Administrator Password CONTEC 70 PT S1000 User s manual 5 BIOS Setup Save amp Exit Use this menu to load save settings changes and exit the setup menu Jtility Copyright C
29. NTEC 66 PT S1000 User s manual 5 BIOS Setup NB PCIe Configuration Copyright C American Megatrends Inc NB PCIe Configuration Configure PEGO B0 D1 FO PEGO Gen X Geni Gen3 PEGO ASPM Enable PEG e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C 11 American Megatrends Inc Figure 5 27 NB PCIe Configuration Settings that can be configured in the NB PCIe Configuration are described in the table below Table 5 23 NB PCIe Configuraiton Explanation PEGO Gen X Configure PEGO Gen 1 Gen 3 Disabled Auto Control ASPM Support for the PEGO PEGO ASPM ASPM 1 06 This has no effect if PEG is not the ASPM LI currently active device ASPM LosL1 Disabled Enable PEG Enabled To Enable or Disable the PEG CONTEC PT S1000 User s manual 67 5 BIOS Setup Memory Configuration Use this menu to check Memory Informations Aptio Setup Utility Copyright C 2 Memory Information Memory RC Version 1 1 0 0 Memory Frequency xxxx Mhz Total Memory xxxx MB DDR3 DIMMA1 DIMMB1 CAS Latency x Minimum delay time CAS to RAS tRCDmin Row Precharge tRPmin Active to Precharge tRASmin e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Def
30. P2 DC7000 External 2 port 29 pin DVI I connector display 920 x 1 200 Max output 6 770 000 colors only one or DVI D only choice port 19 pin HDMI Type A connector 920 x 1 200 Max 6 770 000 colors or HDMI1 4b 1 port 15 pin VGA connector 2 048 x 1 536 Max or VGA LINE OUT x 1 3 5 phi mini jack LINE IN x 1 3 5 phi mini jack MIC IN x 1 3 5 phi mini jack HD Audio compliant Serial ATA 2 5 inch SATA HDD Drive Bay x 1 Option 1 Drive Bay Corresponding to serial ATA 3 0 standard port RJ 45 x 2 1000BASE T 100BASE TX 10BASE T Wake On LAN support LAN Intel 82579LM LANI Intel 82583V LAN2 uss 7 UsBaiox4 USB20x2 9 pin DSUB male x 3 RS 232C general purpose SERIAL PORT1 2 3 9 pin DSUB male x 1 RS 232C 422 485 general purpose SERIAL PORT4 Baud rate 50 115 200bps PS 2 Keyboard amp Mouse General purpose Hardware monitoring Monitoring CPU temperature board temperature power voltage Watch dog timer Software programmable 255 level 1sec 255 sec Causes a reset upon time out Real time clock QM77 integrated The real time clock is accurate within 3 minutes 25 C per month Litihum backup battery life 7 years or more Expansion board slot PCI slot x 2 Usable board dimension 185 mm Max Power management setup via BIOS Power On by Ring Wake On LAN Supports ACPI Power management connector Use a DC power cable shorter than 3m consumption 24VDC
31. PCI Common Settings PCI Latency Timer 32 PCI Bus Clocks Enables or Disabled 64bit capable Devices to be Decoded in Above 4G Address Space Only if System Supports 64 bit PCI Decoding e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C Figure 5 3 PCI Subsystem Settings Items that can be configured for PCI subsystem settings are described in the table below Table 5 3 PCISubsystem Settings Explanation Disable Enabled Above 4G Decoding 82 PCI Bus Clocks 64 PCI Bus Clocks 96 PCI Bus Clocks 128 PCI Bus Clocks 160 PCI Bus Clocks 192 PCI Bus Clocks 224 PCI Bus Clocks 248 PCI Bus Clocks PCI Latency Timer CONTEC Enables or Disables 64bit capable devices to be decoded in above 4G Address space Only if System supports 64bit PCI decoding Value to be programmed into PCI Latency Timer Register PT S1000 User s manual 41 5 BIOS Setup ACPI Settings Use this menu to specify ACPI power management settings Setup Utility Copyright C 2011 American Megatrends Inc Advanced ACPI Settings Select ACPI sleep state the system will enter when the SUSPEND button is pressed ACPI Sleep State S1 Cpu Stop Clock 53 Video Repost Disabled Resume On RTC Alarm Disabled Resume On PCIE Disabled e Se
32. ation PCH Azalia Configuration CONTEC 60 PT S1000 User s manual 5 BIOS Setup USB Configuration up Utility Copyright C USB Configuration Enabled Disabled the xHCI USB3 0 Support Enabled controller for USB3 0 EHCI1 Enabled EHCI2 Enabled USB Ports Per Port Disable Control Disabled e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit 4 1219 Copyright C 2 Figure 5 22 USB Configuration Items that can be configured for USB Configurations are described in the table below Table 5 19 USB Configuration Explanation Enabled Enable or Disable the xHCI USB 3 0 Disab controller Control the USB EHCI USB 2 0 functions EHCI1 One EHCI controller must always be enabled Control the USB EHCI USB 2 0 functions USB3 0 Support EHCI2 One EHCI controller must always be enabled USB Ports Per Port E s Control each of the USB ports disabling Disable Control Disable USB Port x1 8 Note This item can setting only when USB Ports Per Port Disable Control Enabled USB Port x Disable CONTEC PT S1000 User s manual 61 5 BIOS Setup PCH Azalia Configuration etup Utility Copyright C 2011 American Megatrends Inc PCH Azalia Configuration Control Detection of the Azalia device Azalia Disabl
33. aults F4 Save amp Exit ESC Exit 2011 American Megatrends I Figure 5 28 Memory Configuration CONTEC 68 PT S1000 User s manual 5 BIOS Setup yright C Boot Configuration Number of seconds to wait for Setup Prompt Timeout setup acvivation key Bootup NumLock State On 65535 0xFFFF means indefinite waiting Quiet Boot Disabled Boot Option Priorities Boot Option 1 e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C 2011 American Meg Figure 5 29 Boot menu Use this menu to specify settings related to system startup The following items are available Table 5 24 Boot Explanation Number of seconds to wait for setup Setup Prompt Timeout 655 activation key 65535 0xFFFF means indefinite waiting Bootup NumLock State LEE Select the keyboard NumLock state Quiet Boot Enables or disables Quiet Boot opti uiet Boo Disabled nables or disables Quiet Boot option Boot Option x O Sets the system boot order CONTEC PT S1000 User s manual 69 5 BIOS Setup Security Use this menu to configure system security settings Password Description Set Administrator Password If ONLY the Administrator s password is set then this only limits access to Setup and is only asked for when entering Setup If ON
34. ch will be activated during POST Primary IGFX Boot Display LVDS This has no effect if external Secondary IGFX Boot Display CRT graphics present LCD Panel Type 1024x768 LVDS1 Secondary boot display Panel Color Depth 18 Bit selection will appear based on your selection VGA modes will be supported only on primary display e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C 20 erican Megatrends Inc Figure 5 26 LCD Control Settings that can be configured in the LCD Control are described in the table below Table 5 22 LCD Control Explanation Select the Video Device which will be activated during POST VBIOS Default 2 ER This has no effect if external CRT HDMI ILVDS DVI Primary IGFX Boot Display graphics present Secondary boot display selection will appear based on your selection VGA modes will be supported only on primary display Secondary IGFX Bott Display Select Secondary Display Device For PT S1000HX Select LCD panel used by Internal Graphics 1024x768 LVDSI Device by selecting the aooropriate setup For PT S1000XSX item Note Please don t change this item LCD Panel Type Select the LFP Panel Color Depth 000XSX Note Please don t change this item Panel Color Depth CO
35. ct and set this product STEP2 Connect cables Connect the cable of necessary external devices such as keyboard and a mouse to this product using appropriate cables STEP3 Turn on the power After verifying that you have correctly followed steps 1 and 2 turn on the power If you find any abnormality after turning on the power turn it off and check to see if the setup has been performed properly STEP4 Set up BIOS By referring to Chapter 5 set up BIOS This setup requires a keyboard Before using this product be sure to execute LOAD SETUP DEFAULTS to initialize the BIOS settings to their default values See Chapter 5 Menu CAUTION Be sure to connect the keyboard and mouse to it before turning the power on for the first time PT S1000 User s manual 13 3 Hardware Setup Hardware Setup Before you start be sure that the power is turned off Remove only those screws that are explained Do not move any other screw Attaching the HDD 1 Remove the hard disk bracket from the main body 2 Attach the hard disk to the hard disk bracket and secure it by tightening the four screws 3 Insert the hard disk bracket with the hard disk attached into the main body and secure it by tightening the screws Figure 3 1 Attaching the HDD CAUTION Insert the Hard disk face up Screw holes may be damaged if screws tightened with a torque greater than the spec
36. dog timer comes with 255 level time out interval 1 255 seconds per interval which can be adjusted by software setting There is a tolerance of 2 second for this time out interval To maintain normal system operation consider allowable error and create a program to re trigger the watchdog timer CONTEC s Web site IPC SLIB 01 which is bundled with this product contains a sample program for the watchdog timer To view the sample program for the watchdog timer decompress HWMandRTCut zip which is found under RasUtility Samples Module For example if the time out interval has been set to 30 seconds your program should trigger the watchdog timer before 28 seconds are escaped Otherwise after 28 32 seconds are escaped the system will automatically reboot The I O port is defined at address 2e 2fH You can trigger enable disable the timer by writing address 2e 2fH Here is an example for flow chart and programming how to use the watch dog timer 1 Example flow chart START WDT Initial by WDT Start system reset occurs WDT Start If WDT Stop is not performed within the limit time set up It is also possible not to perform WDT Stop instead of performing WDT Stop to WDT Start but to perform WDT Start continuously at the time of a re start PT S1000 User s manual 85 6 Appendix 2 The following example is written in Intel8086 assembly lang
37. e separate and install brace base by using 3 screws Figure 3 13 Hold brace base 5 Insert PCI card into the slot and fasten it with screws Figure 3 14 Insert PCI card 6 Make sure carefully that PCI card has been secured in the slot Fix PCI card stably by brace and Screw Figure 3 15 Fix PCI card CONTEC 20 PT S1000 User s manual 3 Hardware Setup 7 Replace the cover Figure 3 16 Replace the cover The location of brace base Brace base can be installed to 2 locations Select one according to the size of your PCI card eT 57 Figure 3 17 locaction of brace base The Installation of low profile PCI card Use attached spacer for installing low profile PCI card 84 2 gt EI ef pom wow arilosud MOT paw ow ow F 1 Figure 3 18 installation of low profile PCI card PT S1000 User s manual 21 3 Hardware Setup Replace Fan 1 Be sure the power is turned off 2 Remove the top cover 3 Replace Fan A e System Fan Figure 3 19 Replace Fan Replace Fan Filter 1 Be sure the power is turned off 2 Remove the top cover 3 Replace Fan filter Figure 3 20 Replace Fan Filter 22 CONTEC PT S100
38. ed Azalia will be unconditionally disabled Enabled Azalia will be unconditionally Enabled Auto Azalia will be enabled if present disabled otherwise e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit opyright C 2011 American Megatrends Figure 5 23 PCH Azalia Configuration Items that can be configured for PCH Azalia are described in the table below Table 5 20 PCH Azalia Configuration Item Option Explanation Disabled Azalia Enabled Control Detection of the Azalia device Auto CONTEC 62 PT S1000 User s manual 5 BIOS Setup System Agent SA Configuration p Utility Copyright C 2011 American Megatrends Inc System Agent Bridge Name Config Graphics Settings System Agent RC Version VT d Capability gt Graphics Configuration gt NBPCIe Configuration gt Memory Configuration e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C ican Megatrends Inc Figure 5 24 System Agent SA Configuration The following sub items are available Graphics Configuration NB PCIe Configuration Memory Configuration CONTEC PT S1000 User s manual 63 5 BIOS Setup Graphics Configuration etup Ut
39. ed for Serial Port 4 Configuration are described in the table below Table 5 13 Serial Port 4 Configuration Explanation Disabled Serial Port Enable or Disable Serial Port COM Enabled Auto IO 3F8h IRQ 4 IO 3F8h IRQ 3 4 5 6 7 9 10 11 12 Select an optimal setting for Super IO IO 2F8h IRQ 3 4 5 6 7 9 10 11 12 device IO 3E8h IRQ 3 4 5 6 7 9 10 11 12 IO 2E8h IRQ 3 4 5 6 7 9 10 11 12 Change Settings CONTEC 52 PT S1000 User s manual 5 BIOS Setup H W Monitor Use this menu to check CPU temperature system temperature input voltage and other system conditions Advanced PC Health Status Smart Fan function page Smart Fan System temperature CPU temperature System Fan Speed CPU Fan Speed VCORE 12V 5V 5VSB e Select Screen 3VSB T Select Item VBAT Enter Select Change Opt General Help Previous Values Optimized Defaults t Save amp Exit ESC Exit Ver 2 14 1219 Copyright C 2 America Figure 5 15 H W Monitor The following sub items are available Smart Fan Use this menu to specify settings for Smart Fan CONTEC PT S1000 User s manual 53 5 BIOS Setup Smart Fan Use this menu to specify Smart Fan settings Aptio Setup Utility Copyright C 2011 American Megatrends Inc Advanced Smart Fan Smart Fan Function Enable Disable Smart Fan Function Enabled gt Smart Fan Mode Configuration
40. enu The following sub items are available PCH IO Configuration Use this menu to specify the PCH IO configuraion System Agent SA Configuration Use this menu to specify the system agent configuration CONTEC PT S1000 User s manual 59 5 BIOS Setup PCH IO Configuration etup Utility Copyright C 2011 American Megatrends Inc Intel PCH RC Version Config Memory Frequency and Intel PCH SKU Name Timing Settings Intel PCH Rev ID USB Configuration PCH Azalia Configuration LAN1 Controller Enabled Wake on LAN1 Enabled LAN2 Controller Enabled Restore AC Power Loss Power On e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit opyright C 2011 American Megatrends Figure 5 21 PCH IO Configuration Items that can be configured for PCH IO Configurations are described in the table below Table 5 18 PCH IO Configuration Explanation Enabled LANI Controller F Enable or Disable LAN1 Controller Disabled Enable Wake on LAN1 Enable or Disable Wake on LANI Disabled Enable Controller 7 Enable or Disable LAN2 Controller Disabled Power Off Restore AC Power Loss Power Last State Select AC Power state when power is re applied after a power failure The following sub items are available USB Configur
41. es Legacy USB support AUTO option disables legacy USB Devices support if no USB devices are x Keyboard x Point connected DISABLE option will keep USB devices available Legacy USB Support Enabled only for EFI applications e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit 4 1219 Copyright C 2 Figure 5 9 USB Configuration Items that can be configured for USB Configuration are described in the table below Table 5 8 USB Configuraiton Explanation Show only Show USB Devices USB Devices ted connected Enables Legacy USB support AUTO option disables legacy support if no USB devices Legacy USB Support are connected DISABLE option will keep USB devices available only for EFI applications CONTEC PT S1000 User s manual 4T 5 BIOS Setup Super I O Configuration etup Utility Copyright C 2011 American Meg Advanced Super IO Configuration Set Parameters of Serial Port Super IO Chip F81216 Serial Port 1 Configuration Serial Port 2 Configuration Super IO Chip NCT6776F Serial Port 3 Configuration Serial Port 4 Configuration Resume on PS2 KB MS Disabled Watch Dog Timer Disabled e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC
42. eturning any product No product will be accepted by CONTEC group without the RMA number Liability The obligation of the warrantor is solely to repair or replace the product In no event will the warrantor be liable for any incidental or consequential damages due to such defect or consequences that arise from inexperienced usage misuse or malfunction of this device CONTEC 2 PT S1000 User s manual 1 Introduction Safety Precautions Understand the following definitions and precautions to use the product safely Safety Information This document provides safety information using the following symbols to prevent accidents resulting in injury or death and the destruction of equipment and resources Understand the meanings of these labels to operate the equipment safely DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury Ay CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury or in property damage Caution Handling Precautions gt WARNING Always check that the power supply is turned off before connecting or disconnecting power cables Procedures that could result in serious injury or loss of human life should never be performed f
43. figuration Explanation Disabled Serial Port miis Enable or Disable Serial Port COM Enabled Auto 10 260h IRQ 11 10 260 IRQ 10 11 12 Select an optimal setting for Super IO IO 268h IRQ 10 11 12 device 10 270h IRQ 10 11 12 10 278h IRQ 10 11 12 Change Settings CONTEC PT S1000 User s manual 49 5 BIOS Setup Serial Port 2 Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Advanced Serial Port 2 Configuration Enable or Disable Serial Port COM Serial Port Enabled Device Settings IO 268h IRQ 10 Change Settings Auto e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C 2011 American Megatrends Inc Figure 5 12 Serial Port 2 Configuration Items that can be configured for Serial Port 2 Configuration are described in the table below Table 5 11 Serial Port 2 Configuration Explanation Enabled Port COM Auto 10 260h IRQ 11 10 260h IRQ 10 11 12 Select an optimal setting 10 268h IRQ 10 11 12 for Super IO device IO 270h IRQ 10 11 12 10 278h IRQ 10 11 12 Change Settings CONTEC 50 PT S1000 User s manual 5 BIOS Setup Serial Port 3 Configuration Utility Copyright Advanced Serial Port 3 Configuration Enable or Disable Se
44. fter microcode loading alata North Bridge initialization after microcode loading South Bridge initialization after microcode loading OEM initialization after microcode loading B Cache initialization M d E nj S 5 Ei ze S gt M m jur 5 m ho 8 Pre Memory North Bridge initialization North Bridge module specific Pre memory South Bridge initialization is started Ex oji Io Io gt 1h Memory initialization Programming memory timing information gt gt N 5 5 bo n n 3 31h 33h 34h CPU post memory initialization Application Processor s AP initialization 35h CPU post memory initialization Boot Strap Processor BSP selection 37h CPU post memory initialization System Management Mode SMM initialization 38h Post Memory North Bridge initialization is started 39h 3Ah Post Memory North Bridge initialization North Bridge module specific 3Bh Post Memory South Bridge initialization is started 3Ch 3Eh Post Memory South Bridge initialization South Bridge module specific 3Fh 4Eh OEM post memory initialization codes 4Fh DXE IPL is started lt Driver Execution Environment DXE phase gt Em 61h 62h I i 63h 8h 9h NVRAM initialization nstallation of the South Bridge Runtime Services
45. he following message appears briefly at the screen during the POST Power On Self Test Press DEL or F2 to enter setup If the message disappears before you respond and you still wish to enter Setup restart the system to try again by turning it OFF then ON Restart can be initiated by pressing the Ctrl Alt and Delete keys simultaneously PT S1000 User s manual 35 5 BIOS Setup Using Setup In general you use the arrow keys to highlight items press Enter to select use the Page Up and Page Down keys to change entries press F1 for help and press lt Esc gt to quit The following table provides more detail about how to navigate in the Setup program using the keyboard Table 5 1 Using Setup Move to the item on the left menu bar Right Arrow Move to the item on the right menu bar ESC Main Menu Quit without saving changes Submenus Exit Current page to the next higher level menu Save all settings changes to the FLASH ROM and exit Getting Help Press to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item To exit the Help Window press Esc key again In Case of Problems If it is not possible to boot the computer after system settings have been changed and saved during setup this product will need to be repaired The best advice is to only alter settings which you thoroughly understand To this
46. iagnostic local loop back test 0 Disable 1 Enable R Line Status Regester D6 D5 D4 D3 D2 0 TEMT THRE BI DR E Data ready 1 for existence of received data Overrun error 1 for occurrence of an error Parity error 1 for occurrence of an error Framing error 1 for occurrence of an error Break interrupt 1 for detection of break state Transmitter holding register empty 1 for transmission buffer being empty Transmitter empty Set to 1 when both transmitter holding register and transmitter shift register are empty CONTEC 82 PT S1000 User s manual Table 6 6 Function of Each Register 4 4 I O address Description 6 Appendix 03FEH MSR Modem Status Register D6 D5 D4 D3 D2 Di DO DCD RI DSR CTS DDCD TERI DDSR DCTS SCR Scratchpad Register This is an 8 bit readable writable register which is available to the user to allow data to be saved temporarily Delta CTS Delta DSR Trailing edge RI ta data carrier detect CONTEC PT S1000 User s manual 83 6 Appendix Baud Rate Settings A baud rate is set by software by dividing the clock input 1 8432MHz The baud rate terms of hardware can be set to a maximum of 115 200 bps for SERIAL A B C D The baud rates available in practice depend on the operati
47. ified torque The specified tightening torque is 3 3 5kgf cm CONTEC 14 PT S1000 User s manual 3 Hardware Setup Attaching the FG 1 Use screws to attach the FG Attached screw M3 x 8 Figure 3 2 Attaching the FG CAUTION The FG pin of this product is connected to the GND signal of the DC power connector DC IN Note that the connection cannot be cut off Screw holes may be damaged if screws are tightened with a torque greater than the specified torque The specified tightening torque is 5 6kgf cm Fastening the Cable This product comes with cable ties for fixing cables Fastening the PS2 Audio Cable Use the cable ties appropriately to fasten cables and fix it by using the hole on a chassis Fastening the USB HDMI Cable Use the cable ties appropriately to fasten cables USB HOMI YJ 100 CABLETIE Figure 3 3 Attaching the cable ties CONTEC PT S1000 User s manual 15 3 Hardware Setup Hardware Setup 1 Cut out a panel according to the following dimensions to mount the main unit 400 289 PT S1000HX PT S1000XSX Panel thickness range 1 6 7mm mm Figure 3 4 Dimensions of Panel Opening 2 Place the waterproof packing in the groove on the front face of the main body and insert the main body into the panel from the external side Waterproof packing supplied Figure 3 5 Attaching the waterproof
48. iguration and reset No Pressing Yes saves any changes made in FLASH ROM and reboots the system The next time the computer is booted the BIOS configures the system based on the configuration stored in FLASH ROM Pressing No lets you go back to setup menu Restore Defaults Pressing Enter key shows confirmation dialog box and shows the message below Load Optimized Defaults Load Optimized Defaults No Pressing Yes loads the default values that are factory settings for optimal performance system operations This setting will not be stored in FLASH ROM before saving it Pressing No lets you go back to setup menu without loading it Boot Override Using the cursor to select the device that you want to start and pressing lt Enter gt key directly boots the selected device regardless of the order set in the Boot menu POST Beep POST Beep indicates that a video error has occurred or that no memory is installed It indicates the BIOS cannot initialize the video screen to display any additional information CONTEC 72 PT S1000 User s manual 6 Appendix 6 Appendix Memory Map Table 6 1 Memory Map PT S1000 User s manual 73 6 Appendix I O Port Addresses Table 6 2 I O Port Addresses 0000 001F 32 bytes DMA controller 0020 0021 0376 03B0 03BB 03C0 03DF 18 1 18 bo to 32 1 8 8 16 8 8 8 8 16 8 1 byte
49. ility Copyright C 2011 American Megatrends Inc Graphics Configuration Select which of IGFX PEG PCI Graphics device should be Primary Display Auto Primary Display Or select SG Internal Graphics Auto for Swithable Gfx DVMT Pre Allocated 64M DVMT Total Gfx Mem 256M LCD Control e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit opyright C 2011 American Megatrends Figure 5 25 Graphics Configuration Items that can be configured for Graphics are described in the table below Table 5 21 Graphics Configuration Select which of IGFX PEG PCI Graphics device should be Primary Display Primary Display Auto Internal Graphics Disabled Enabled Keep IGD enabled based on the setup options Select DVMT 5 0 Pre Allocated Fixed DVMT Pre Allocated Graphics Memory Size used by the Internal Graphics Device Select DVMT 5 0 Total Graphics Memory Size used by the Internal Graphics Device DVMT Total Gfx Mem CONTEC 64 PT S1000 User s manual 5 BIOS Setup The following sub items are available LCD Control Use this menu to specify the LCD Control PT S1000 User s manual 65 5 BIOS Setup LCD Control Aptio Setup Utility Copyright 2011 American Meg LCD Control Select the Video Device whi
50. ion System Agent SA Configuration 63 Graphics Config ration ee tege DER e 64 LED nm 66 ATRAER 67 Memory Configuration ha E 69 Mv MMI 70 Save Sc ER ERBEN ERREUR EXER CEP ENERO 71 5 72 6 APPENDIX 73 Memory Map iss erre de E Sa ee RE SV ERN ERES NR ENSE IIND 73 eH E OE HE OH HEURE aga 74 Interrupt Level List Oe e RE E ERN 75 POST E des RE ERE DERE IER dr EI EE BISHER EE SES 76 SERIAL I O Address and Register 79 Watch Dog Timer DD 85 Battery 89 7 LIST OPTIONS 91 PT S1000 User s manual CONTEC PT S1000 User s manual 1 Introduction 1 Introduction About the Product This product is available in the following 2 models 15 LCD panel mount type with 2 PCI slots supporting 3 Generation Intel amp Core Processors PT S1000HXP2 DC7000 15 inch touch panel LCD XGA Memory 4GB 2 PCI slots Option CPU OS 2 5 inch HDD Power supply 17 LCD panel mount type with 2 PCI slots supporting 34 Generation Intel Core Processors PT S1000XSXP2 D
51. l Doing so may scratch the touch panel resulting in malfunctions Do not subject the touch panel to shock as doing so may break it When the surface or frame of the touch panel has become dirty wipe it with neutral detergent Do not wipe the touch panel with thinner alcohol ammonia or a strong chlorinated solvent Use a protective sheet available as an option if the touch panel is used where it can easily collect dust and dirt It is a characteristic of analog touch panels that their resistance may vary with changes to the ambient environment temperature and humidity and with their own aging resulting in the deviation of the detection point If this is the case calibrate the touch panel again to re set calibration data LCD may have a few bright spots that are always on or a few black spots that are always off Color irregularity may also occur depending on the viewing angle This however is due to the structural characteristics of the LCD therefore it is not a product fault Burn in on TFT Display Burn in may occur if the same display is retained for a long time Avoid this by periodically switching the display so that the same display is not maintained for a long time Burn In Phenomenon characterized by a TFT display as a result of long time display of the same screen where a shadow like trace persists because electric charge remains in the LCD element even after the patterns are changed CONTEC PT S1000 User s
52. lect Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit er 2 14 1219 Copyright C 2011 American Megatrends Inc Figure 5 4 ACPISettings Items that can be configured for ACPI Settings are described in the table below Table 5 4 ACPI Settings Explanation Bion CPU Stop Clock Select ACPI sleep state the system will ACPI Sleep State S3 oxly Guspend to enter ad the SUSPEND button is pressed Disabled 53 Video Repost Enable or Disable S3 Video Repost Enabled Enable or disable System wake on alarm Disabled Resume On RTC Alarm event When enabled System will wake on Enabled the hr min sec specified Select 0 for daily system wake up 1 31 for RTC Wake up Day 0 81 which day of the month that you would like the system to wake up Select 0 23 For example enter 3 for 3am RTC Wake up Hour 15 for 3pm Wake up Minute Wake up Minute 59 Select 0 59 RTC Wake up Second Select 0 59 5 Resume On ed Enable or disable system wake on PCI E Disabled devices or Onboard LAN2 CONTEC 42 PT S1000 User s manual 5 BIOS Setup CPU Configuration Use this menu to specify CPU settings Aptio Setup Utility Copyright C 2011 American Megatrends In Advanced CPU Configuration
53. m Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C 2011 American Megatrends Inc Figure 5 2 Advanced menu The following sub items are available PCI Subsystem Settings Use this menu to specify the pci subsystem settings ACPI Settings Use this menu to specify ACPI power management settings CPU Configuration Use this menu to specify the cpu configuration SATA Configuration Use this menu to specify the SATA configuration PCH FW Configuration Use this menu to check the PCH Firmware configuration AMT Configuration Use this menu to specify the Intel amp Active Management Technology configuration CONTEC PT S1000 User s manual 39 5 BIOS Setup USB Configuration Use this menu to specify the usb configuration Super I O Configuration se this menu to specify the Super I O configuration H W Monitor Use this menu to check hardware monitor Option Rom Policy se this menu to specify the Option Rom CPU PPM Configuration se this menu to specify the CPU PPM configuration Cc CONTEC 40 PT S1000 User s manual PCI Subsystem Settings Use this menu to specify PCI subsystem settings Aptio Setup Utility Copyright C Advanced 5 BIOS Setup Megatrends 1 PCI Bus Driver Version V 2 05 02 PCI 64bit Resources Handling Above 4G Decoding Disabled
54. n the line status register is read Generated when the receive buffer register is ready Cleared when the receiving buffer is read Generated when the transmitter holding register is empty Cleared when the IIR is read or when transmitted data is written to THR Modem status interrupt is generated CTS DSR RI CD Cleared when the modem status register is read D6 LCR Line Contror Regester Bit table 05 D4 03 D2 Di DO 5 Lo 1 6 T 8 0 1STOP bit 1 1 5 STOP bits at 5 bit length STOP bits at 6 7 or 8 bit length 0 Disable parity 1 Enable parity 1 1 2 0 Odd parity 1 Even parity Disable stick parity Enable stick parity 0 Break signal off 1 Send break signal DLAB Divisor Latch Access Bit In order to access the divisor latch register you need to set the bit to 1 To access another register set the bit to 0 CONTEC 6 Appendix PT S1000 User s manual 81 6 Appendix Table 6 6 Function of Each Register 3 4 I O address Description 03FCH MCR Modem Control Register D6 D5 D4 D2 DO 0 IRQ X RTS DTR DTR 0 Inactive HIGH 1 Active LOW RTS 0 Inactive HIGH 1 Active LOW Interrupt control bit 0 Disable 1 Enable L D
55. nector on the connector side Housing 9357 04 mfd by ALEX or 5557 04R mfd by MOLEX Contact 4256T2 LF AWG18 24 mfd by ALEX or 5556 AWG18 24 mfd by MOLEX Applicable connector on the connector side Voltage 12V Time Figure 4 2 Graph of Rise Time of Power Supply CONTEC 24 PT S1000 User s manual 4 Each Component Function Power switch POWER SW POWER SW is provided Reset switch RESET SW RESET SW is provided Line out Interface LINE OUT A line output connector is provided You can plug a headphone or amplifier integrated speakers into this connector Line in Interface LINE IN A line input connector is provided You can plug an audio output device into this connector Mic in Interface MIC A MIC input connector is provided You can plug a microphone into this connector Audio driver The audio driver is required to use the microphone input and line output interfaces Install the appropriate audio driver for your OS from the CONTEC s Web site USB 3 0 Ports USB 3 0 This product is equipped with 4 ports for USB 3 0 interface Table 4 4 USB 3 0 Connector pw 3 1 re USB 2 0 Ports USB 2 0 This product is equipped with 2 ports for USB 2 0 interface Table 4 5 USB 2 0 Connector CONTEC PT S1000 User s manual 25 4 Each Component Function PS 2 Keyboard Mouse This product is equipped with 1
56. ng environment cable software etc The table below lists typical baud rates and their respective values to be written to the divisor latch register LSB MSB Table 6 7 Baud Rate Settings Baud rate to be set SERIAL A B C D Clock input 1 8432MHz Value to be set in the divisor register Setting error Decimal 2304 Example set 9 600 bps write 00 to the MSB divisor latch register and 12 decimal to the LSB divisor latch register CONTEC 84 PT S1000 User s manual 6 Appendix Watch Dog Timer The watchdog timer serves as a safeguard against possible system lock up in your industrial computer system In most industrial environments there are heavy equipment generators high voltage power lines or power drops that have adverse effects on your computer system For instance when a power drop occurs it could cause the CPU to come to a halt state or enter into an infinite loop resulting in a system lock up The application software created by user with the watchdog timer enabled a RESET automatically generated unless the software periodically triggers the timer within the setting time out interval That is while the system gets hung up the running program can t trigger the timer periodically The timer will generate a reset signal to reboot the system This feature allows a running program to restart in an orderly way when a power glitch or any abnormal condition occurs The watch
57. oltage 3 Nominal capacity 1000mAh Lithium content 1g or less Removing the battery 1 Be sure the power is turned off 2 Remove the top cover 3 Remove battery system Fan Figure 6 1 Removing the battery Disposing the battery Dispose the removed battery properly as instructed by local government CONTEC PT S1000 User s manual 89 6 Appendix CONTEC 90 PT S1000 User s manual 7 List of Options 7 List of Options AC adapter Please ask your retailer Hard disk PC HDD100S 2 5 inch SATA HDD 100GB Other option IPC SND 03 Desk stand Check the CONTEC s Web site for the latest information on these options CONTEC PT S1000 User s manual 91 51000 Series User s Manual PT S1000HXP2 DC7000 PT S1000XSXP2 DC7000 CONTEC CO LTD July 2014 Edition 3 9 31 Himesato Nishiyodogawa ku Osaka 555 0025 Japan Japanese _http www contec co jp English http www contec com Chinese http www contec com cn No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO LTD 07042014 Management No NA03524 Parts No LYRS551
58. ons Parameter Condition PT S1000HXP2 DC7000 PT S1000XSXP2 DC7000 Visual ET 140deg 150deg 140deg 150deg CR 10 ET Display 20deg 10deg 20deg 10deg ae 70deg 80deg 70deg 80deg 70deg 80deg 70deg 80deg Surface brightness Display in white 320cd m 400cd m 280 cd m 350 cd m at center Surface brightness represents a numerical value per display The expected brightness through a touch panel is about Visual E MI E MI 80 lower than the above value Brightness at screen center with white displayed Contrast ratio CR 5 Brightness at screen center with black displayed Z Measurement direction T 2 45 180 Module Bottom Tq Right en 90 X Figure 2 1 Definition of viewable range CAUTION The above optical specification data shows optical characteristics of the liquid crystal in the display the data does not represent the actual view on the display or its viewing angles CONTEC 10 PT S1000 User s manual 2 System Reference Power Management Features Support both ACPI Advanced Configuration and Power Interface and legacy APM power management ACPI v2 0 compliant APM v1 2 compliant Support hardware automatic wake up Power Requirements Your system requires a clean steady power source for reliable performance of the high frequency CPU on the product the quality of the power supply is even more important For the best performance makes su
59. p to date information on products CONTEC also provides product manuals and various technical documents in the PDF Free download You can download updated driver software and differential files as well as sample programs available in several languages For product information Contact your retailer if you have any technical question about a CONTEC product or need its price delivery time or estimate information Limited One Year Warranty CONTEC products are warranted by Contec Co Ltd to be free from defects in material and workmanship for up to one year from the date of purchase by the original purchaser Repair will be free of charge only when this device is returned freight prepaid with a copy of the original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office from which it was purchased This warranty is not applicable for scratches or normal wear but only for the electronic circuitry and original products The warranty is not applicable if the device has been tampered with or damaged through abuse mistreatment neglect or unreasonable use or if the original invoice is not included in which case repairs will be considered beyond the warranty policy How to Obtain Service For replacement or repair return the device freight prepaid with a copy of the original invoice Please obtain a Return Merchandise Authorization number RMA from the CONTEC group office where you purchased before r
60. packing 3 Hold the attachment fittings from the inside of the panel Panel Metal fittings REN Main body 51000 51000 5 Figure 3 6 Hardware Setup A CAUTION Screw holes may be damaged if screws are tightened with a torque greater than the specified torque The specified tightening torque is 5 6kgf cm CONTEC 16 PT S1000 User s manual 3 Hardware Setup When using VESA standard 100mm mounting holes The main body has mounting holes according to VESA standard 100mm When using a VESA standard 100mm stand or the like attach it as shown the following figure VESA arm example of reference Figure 3 7 Installation of VESA metal fittings Installation Requirements Be sure that the ambient temperature is within the range specified in the installation environment requirement by making space between the product and device that generates heat or exhaust air Installed angle which is recommended 45 Installed angle of this product which is recommended is 0 459 Except for that the temperature specification of this product might not be filled Figure 3 8 Installed angle which is recommended AN CAUTION Note that even though the ambient temperature is within the specified range an operational malfunction may occur if there is other device generating high heat the radiation will influence the product to increase its temperature CONTEC PT S1000 User s manual 17
61. radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference at his own expense WARNING TO USER Change or modifications not expressly approved the manufacturer can void the user s authority to operate this equipment PT S1000 User s manual 5 Introduction CONTEC 6 PT S1000 User s manual 2 System Reference 2 System Reference Specification Table 2 1 Functional Specification PT S1000HXP2 DC7000 PT S1000XSXP2 DC7000 Panel mounted CP Recommended Core 17 3610QE 3 30GHz Available Core i5 3610ME 2 70GHz Core i3 3120ME 2 40GHz Celeron 1020E 2 20GHz U BIOS BIOS mfd by 4GB 204pin SO DIMM x 2 DDR3 1333 1600 Option 4GB Graphic ntel HD4000 Built in Intel Core Processor Video RAM Main memory shared Video BIOS 64 LCD type LCD type 15 inch XGA 1024 x 768 17 inch SXGA 1280 x 1024 TFT color LCD 16 770 000 colors Backlight LED method The ON OFF software can control Touch panel Resolution 2048 x 2048 Emulated in 1024 x 768 mode Emulated in 1280 x 1024 mode Detection Resistive film analog type method Internal USB port CONTEC PT S1000 User s manual 7 2 System Reference Table2 2 Interface PT S1000HXP2 DC7000 PT S1000XSX
62. re your power supply provides a range of 10 8 V minimum to 31 2 V maximum DC power source Power Consumption For typical configurations the CPU card is designed to operate with at least a 60W power supply The power supply must meet the following requirements Rise time for power supply 2 ms 30 ms The following table lists the power supply s tolerances for DC voltages Table 2 5 DC voltage tolerance DC Voltage Acceptable Tolerance 12 24VDC 10 8 31 2VDC CONTEC PT S1000 User s manual 11 2 System Reference Physical Dimensions PT S1000HXP2 DC7000 358 Cut out Dimension 373 304 357 EBD e E 1045 mm SDT ML ru 0 rx Figure 2 2 Physical Dimensions PT S1000HXP2 DC7000 PT S1000XSXP2 DC7000 m 400 Cut out Dimension 113 5 45 338 354 mm 113 Camm EM ot T PER Figure 2 3 Physical Dimensions PT S1000XSXP2 DC7000 CONTEC 12 PT S1000 User s manual 3 Hardware Setup 3 Hardware Setup Before Using the Product for the First Time Follow the next steps to set up this product STEPI By referring to the information in this chapter install conne
63. rial Port COM Serial Port Enabled Device Settings IO 2F8h IRQ 3 Change Settings Auto e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C 11 American Megatrends Inc Figure 5 13 Serial Port 3 Configuration Items that can be configured for Serial Port 3 Configuration are described in the table below Table 5 12 Serial Port 3 Configuration Explanation Disabled Serial Port nias Enable or Disable Serial Port COM Enabled Auto IO 2F8h IRQ 3 IO 3F8h IRQ 3 4 5 6 7 9 10 11 12 Select an optimal setting for Super IO IO 2F8h IRQ 3 4 5 6 7 9 10 11 12 device IO 3E8h IRQ 3 4 5 6 7 9 10 11 12 IO 2E8h IRQ 3 4 5 6 7 9 10 11 12 Change Settings CONTEC PT S1000 User s manual 51 5 BIOS Setup Serial Port 4 Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Advanced Serial Port 4 Configuration Enable or Disable Serial Port COM Serial Port Enabled Device Settings IO 3F8h IRQ 4 Change Settings Auto e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit opyright C 2011 American Megatrends Figure 5 14 Serial Port 4 Configuration Items that can be configur
64. rom a touch panel Use system design methods that can guard against input errors Do not modify the product Always turn off the power before inserting or removing circuit boards or cables This product is not intended for use in aerospace space nuclear power medical equipment or other applications that require a very high level of reliability Do not use the product in such applications If using this product in applications where safety is critical such as in railways automotive or disaster prevention or security systems please contact your retailer Do not attempt to replace the battery as inappropriate battery replacement poses a risk of explosion For battery replacement contact your retailer as it must be performed as a process of repair When disposing of a used battery follow the disposal procedures stipulated under the relevant laws and municipal ordinances CONTEC PT S1000 User s manual 3 1 CAUTION Introduction Do not use or store this product in a location exposed to high or low temperature that exceeds range of specification or susceptible to rapid temperature changes Example Exposure to direct sun In the vicinity of a heat source Do not use this product in extremely humid or dusty locations It is extremely dangerous to use this product with its interior penetrated by water or any other fluid or conductive dust If this product must be used in such an environment install it on a dus
65. t proof control panel for example Avoid using or storing this product in locations subject to shock or vibration that exceeds range of specification Do not use this product in the vicinity of devices that generate strong magnetic force or noise Such products will cause this product to malfunction Do not use or store this product in the presence of chemicals To clean this product wipe it gently with a soft cloth dampened with either water or mild detergent Do not use chemicals or a volatile solvent such as benzene or thinner to prevent pealing or discoloration of the paint This product s case may become hot To avoid being burned do not touch that section while this product is in operation or immediately after turning off the power Avoid installation in a location where people may come into contact with that section CONTEC does not provide any guarantee for the integrity of data on storage Always disconnect the power cable from the receptacle before connecting or disconnecting any connector To prevent corruption of files always shutdown the OS before turning off this product CONTEC reserves the right to refuse to service a product modified by the user In the event of failure or abnormality foul smells or excessive heat generation unplug the power cord immediately and contact your retailer To connect with peripherals use a grounded shielded cable Do not use any sharp pointed object such as a mechanical pencil to touch the touch pane
66. uage Example programming MOV DXJ2EH MOV AL 87H OUT DX AL OUT DX AL MOV DX 2EH MOV AL 2BH OUT DX AL MOV DX 2FH MOV AL ODH OUT DX AL MOV DXJ2EH MOV AL 07H OUT DX AL MOV DX 2FH MOV AL 08H OUT DX AL MOV DX 2EH MOV AL 30H OUT DX AL MOV DX 2FH MOV AL 01H OUT DX AL MOV DX 2EH MOV AL F5H OUT DX AL MOV DX 2FH MOV AL 00H OUT DX AL Exit the extended function mode 86 CONTEC PT S1000 User s manual 6 Appendix MOV DX 2EH MOV AL AAH OUT DX AL gt lt WDT START counter set and a start gt MOV DX 2EH MOV AL 87H OUT DX AL OUT DX AL MOV DX 2EH MOV AL 07H OUT DX AL MOV DX 2FH MOV AL 08H OUT DX AL MOV DX 2EH MOV AL F6H OUT DX AL MOV DX 2FH The data of an example is 15 seconds 01 H 1sec FFH 255sec MOV AL OFH OFH 15Sec MOV DX 2EH MOV AL AAH OUT DX AL MOV DX 2EH MOV AL 87H CONTEC PT S1000 User s manual 87 6 Appendix A CAUTION The timer s intervals have a tolerance of 2 seconds OUT DX AL OUT DX AL MOV DX 2EH MOV AL 07H OUT DX AL MOV DX 2FH MOV AL 08H OUT DX AL MOV DX 2EH MOV AL F6H OUT DX AL MOV DX 2FH The data of 00H is stop WDT MOV AL 00H MOV DX 2EH MOV AL AAH OUT DX AL CONTEC 88 PT S1000 User s manual 6 Appendix Battery Battery Specification This product uses the following battery Type Lithium primary battery Model 1 2 Panasonic Nominal v
67. y Vanderpool Technology CONTEC PT S1000 User s manual 43 5 BIOS Setup SATA Configuration SATA Controller s Enabled Enable or disable SATA Device SATA Mode Selection IDE Serial ATA Port 1 Serial ATA Port 2 Selral ATA Port 3 Serial ATA Port 4 Cfast e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Ver 2 14 1219 Copyright C Figure 5 6 SATA Configuration Items that can be configured for SATA Configuration are described in the table below Table 5 6 SATA Configuraiton Explanation Disabled SATA Controller s Enable or disable SATA devices Enabled IDE SATA Mode Selection Determines how SATA controller s operate Indicates the maximum speed the SATA controller can support Gen3 is only SATA Controller Speed supported in SATA1 and SATA2 This item can only setting in AHCI or RAID mode CONTEC 44 PT S1000 User s manual 5 BIOS Setup PCH FW Configuration Use this menu to check the PCH Firmware configuration Advanced ME FW Version ME Firmware Mode ME Firmware Type ME Firmware SKU 8 0 4 1441 Normal Mode Full Sku Firmware 5MB e Select Screen T Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit
68. y be copied or reproduced in any form by any means without prior written consent of CONTEC Co Ltd CONTEC Co Ltd makes no commitment to update or keep current the information contained in this document The information in this document is subject to change without notice AII relevant issues have been considered in the preparation of this document Should you notice an omission or any questionable item in this document please feel free to notify CONTEC Co Ltd Regardless of the foregoing statement CONTEC assumes no responsibility for any errors that may appear in this document or for results obtained by the user as a result of using this product Trademarks Intel Intel Atom Intel Core and Celeron are registered trademarks of Intel Corporation MS Microsoft and Windows are trademarks of Microsoft Corporation Other brand and product names are trademarks of their respective holder CONTEC ii PT S1000 User s manual Table of Contents Check Your Package iesnjsulm ii Trademarks die a e etm eid ii Contents EN E ne INTRODUCTION 1 About the Products uses es ing CUR TR EDEN URN etr Rr e 1 I uui 1 S pport d OS 1 Customer Suppo Ea N 2 Web Site cce

User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents