ZDAC-2501A User`s Manual
Contents
1. alarm output and alarm registered general card or the card with a oS s c2 3 output low level password can be registered passwords ge 22 g B ST OSTATUS door magnetism input setup by cardholders Door Button o 3 ae Sol Bs terminal their own input in the first time 5 2 q YOR they Aann Bol 5 w Maga BT BUTTON go button terminal door state detection only after p gt low level unlock close stable then start locking signal Door Magnetism DO Weigand 26 reader data lines preventing the door in the swing when data 0 the latch resulting in on the impact of Q 3 D1 Weigand 26 reader data lines electric locking bolt data 1 A with door magnetism interface O Q NC normally closed relay points with the alarm when open the door current load capacity DC1A 120V NO normally open relay point current load capacity DC1A 120V violence FEATURES This model ZDAC 2501A looks generous stable performance use for the office office buildings and so on 500 cards has adequate capacity to meet users need a variety of ways to open the door allows you to set permissions arbitrary Indicator Note Red light Power instructions the red A machine does not have this feature Power is red light means normal Different models registered capacity Green light the green light said from 100 to 5 000 range unlock put out that state lock Yellow light yellow light flashing said2. waiting for keyboard input always Working environment Voltage DC 8 V 15 V standard 5 kinds of open door mode card to open 12V the door Password to open the door yellow light open said that the Current when Do not drive electric lock card password to open the door programming mode lt 70mA card card to open the door 4 gt Reset the system Back to factory default setting Turn off the power supply then press Exit Button BT and hold it then turn on the power supply after about 3 seconds the buzzer will give a long sound you can release Exit Button then the system initialization is finished and comes back to factory default setting Initial password 12345 Temperature 0 C 70 C password password to open the door Humidity 30 90
3. 1 Card Password refers to open the door 2 User passwords setup enter when user use card to open door in the first time 3 Other Notes please refer accession card users 2 8 5 button the system initialization in the programming mode effective 1 By 50 key 2 By ENT key buzzer gives a bell all user data to delete the success the factory password recovery password is 12345 2 9 The introduction of System Programming mode two kinds of methods choose one 1 according to different state on many occasions by ENT key know MODE orange lights went out access control system programming exit and the machine introduced into the normal working condition 3 The installation of wiring diagram No 1 Red 2 Black 3 Yellow 4 Gray 5 Blue 6 Green 7 White Door Go off External Punguon FOWE pon alan magnetism button Card reader Tab 12V GND ALM ST BT D1 DO 8 Brown 9 Purple 10 Pink 11 Pink ElectricLock control Doorbell switch NC NO Bell1 Bell2 gt ZDAC 2501A Wiring Diagram No BELL BELL 12 V power supply anode the effective range DC 8 V 12 V GND power supply cathode public Wiring port definition and performance Features 500 people registered capacity high cost performance digging every hardware resources land Quick issuers mode whether it is a 3 DE ALM
4. Standalone Access Controller ZDAC 2501A User s Manual 1 Access to use the machine Directly in the sensor area corresponding switch use card or enter a password ENT key 2 Access control machine programming methods 2 1 ENT key function keys enter the programming mode 1 Press ENT button MODE orange lights 2 Input five digit system password and then ENT key gives a short buzzer out MODE orange lights always open access control machine programmed into the system state Note The password is 4 8 bit random figure if forget password please reset the system then it will come back to the initial password 12345 See 4 Click commands are only in a state of the implementation of programming after the completion of each order must be exit programmed state No 9 orders and then re enter the command to run other 2 2 0 button to open the door to amend delay time in the programming mode effective 1 0 button 2 According to 5 for 5 seconds delay delay here range of 1 255 seconds 3 By ENT key buzzer gives short sound delay modify success 2 3 1 key modify system password in the programming mode effective 1 Press 1 key 2 Input five bit number passwords 3 By ENT key buzzer gives short sound password modification success Note The password length bit arbitrary figures for the 4 8 2 4 2 key adding card users in the programming mode effective 1 Press 2
5. key 2 Input card number or card 3 By ENT button if by card do not need to press ENT a short buzzer sound the success of the registration card Note 1 Support 10 bit Number 8 bit number or card down right side that 5 bit 2 Card record is a comma of right side of the card that 5 numbers by virtue of this string of numbers you can write off this user card Recommends when users card issuers the profile number save 2 5 2 key adding a password based users in the programming mode effective 1 Press 2 key 2 Enter the number of passwords password length 6 bit 3 By ENT key buzzer gives short sound password registered success Note when registration multi number of the password simply in order to repeat steps 2 3 can register a maximum of 500 passwords 2 6 3 key to delete a single user in the programming mode effective 1 nor key 2 Enter the registration number or password 3 By ENT key buzzer gives short sound the success of user write off Note The number in support of 10 8 5 digit write off of more than a card or password simply repeat steps 2 3 2 7 4 key adding card password type users card card users password password users with the same type of set in programming mode effective 1 By 4 key 2 Input card number or card 3 By ENT button input card then do not need to press ENT buzzer gives short sound a successful user registration Note
Download Pdf Manuals
Related Search