WINDOW AIR CONDITIONER
Contents
1. any 7 minute interval the unit will beep to indicate the Follow Me mode has ended The actual temperature can be displayed at the unit by pressing the Fan only mode When in the Cool mode the unit display indicates the set temperature NOTE DISPLAYS Shows the set temperature in C or F and the Auto timer settings While on Fan only mode it shows the room temperature Error Codes AS Room temperature sensor error Unplug the unit and plug it back in If error repeats call customer service HS Electric heating sensor error Unplug the unit and plug it back in If error repeats call customer service Evaporator temperature sensor error Unplug the unit and plug it back in If error repeats call customer service e is displayed as shown in left picture NOTE In Fan only mode unit will display Lo or Hi ADDITIONAL THINGS YOU SHOULD KNOW e The Cool circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly After unit is turned off leave unit off for a minimum of 3 minutes before attempting to turn back on This prevents overheating of the compressor and possible circuit breaker tripping The fan will continue to run during this time e The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius To convert from one to the other press and hold the Up and Down Temp Timer buttons at the same time for2. filter by sliding out from the right hand side Wash the filter using liquid dishwashing detergent and warm water Rinse filter thoroughly Gently shake excess water from the filter Be sure the filter is thoroughly dry before replacing Or instead of washing you may vacuum the filter clean NOTE Never use hot water over 104 F 40 C to clean the air filter Never attempt to operate the unit without the air filter Cabinet Cleaning Be sure to unplug the air conditioner to prevent shock or fire hazard The cabinet and front may be dusted with an oil free cloth or with a cloth dampened in a solution of warm water and mild liquid dishwashing detergent Rinse thoroughly and wipe dry Never use harsh cleaners wax or polish on the cabinet front Be sure to wring excess water from the cloth before wiping the controls Excess water in or around the controls may cause damage to the air conditioner Plug in air conditioner after unit has dried completely Winter Storage If air conditioner will be stored during the winter remove it carefully from the window according to the installation instructions Cover it with plastic or return it to the original carton Always store unit in upright position 13 TROUBLESHOOTING TIPS Before calling for service please review the chart below AIR CONDITIONER NOT COOLING ROOM OR NOT BLOWING COLD AIR AIR CONDITIONER COOLING BUT ROOM IS TOO WARM ICE FORMING ON COOLING COIL BE
3. is adequate for the model you have chosen This information can be found on the serial plate which is located on the DO NOT under any side of the cabinet and behind the grille circumstances cut Be sure the air conditioner is properly grounded To minimize shock and fire remove or bypass hazards proper grounding is important The power cord is equipped with a grounding prong three prong grounding plug for protection against shock hazards Your air conditioner must be used in a properly grounded wall receptacle If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker have a qualified electrician install the proper receptacle Ensure the receptacle is accessible after the unit installation Do notrun air conditioner without side protective cover in place This could Power supply cord result in mechanical damage within the air conditioner with 3 prong grounding plug Do not use an extension cord or an adaptor plug and current detection device Operation of Current Device The power supply cord contains a current device that senses damage to the power Plug in amp cord To test your power supply cord do the following press RESET 1 Plug in the air conditioner 2 The power supply cord will have TWO buttons on the plug head Press the TEST button The RESET button will click as it pops out 3 Press the RESET button again you will noti
4. long period of time turn OFF main power switch Leaving power on may cause unit failure or fire 1 Always insert the filters securely Clean filter AT LEAST once every two weeks Operation without secured filters may cause failure A dirty filter can cause the unit to not run efficiently NEVER drink water drained from air conditioner Water from unit contains contaminants and could cause illness L If water enters the unit turn the unit off at the power outlet and switch off the circuit breaker Isolate supply by taking the power plug out and contact a qualified serviced technician There is danger of electric shock Meeting Electrical Requirements Electrical Shock and Personal Injury Hazard Electrical ground is required on this appliance DO NOT ground to a gas line If cold water pipe is interrupted by using plastic non metallic gaskets or other insulating materials DO NOT use for grounding Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded DO NOT modify power supply cord plug If it does not fit the outlet have a proper outlet installed by a qualified electrician DO NOT have a fuse in the neutral or grounding circuit A fuse in the neutral or grounding circuit could result in an electrical shock DO NOT use an extension cord with this appliance Failure to follow these instructions could result in electr
5. may e cause moisture to enter the room Do not place obstacles around air inlets or inside of air outlet Obstacles may cause appliance e failure or accident L Use only a soft cloth to clean the unit and installing Cleaners or detergents may change the color or scratch the surface of the unit Do not place heavy objects on the power cord and always ensure that the cord is not compressed There is danger of fire or electric shock Nac Do not clean with water Doing so may cause an injury Water may enter the unit and degrade the insulation causing an Do not put a pet or house plant where it will be exposed to Cleaning unit when power is ON 9 This could injure the pet or plant L Hold the plug by the head of the power plug when taking it out Failure to do so may cause electric shock and damage Periodically check installation bracket for damage Prolonged exposure to outdoor elements may cause damage to installation bracket causing unit to fall L Use caution when unpacking Sharp edges could cause injury L Ensure proper ventilation especially in rooms with a stove or other appliances 9 Failure to do so may result in an oxygen shortage Use only as intended This unit is NOT intended to preserve precision devices food pets plants and art objects It may cause deterioration of quality etc L If unit will not be used for a
6. 3 seconds Air Directional Louvers HOW TO USE The louvers will allow you to direct the air flow left or right throughout the room as needed Move the levers from side to side until the desired left right direction is obtained INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN Read these instructions completely and carefully IMPORTANT Save these instructions IMPORTANT Observe all governing codes and ordinances Note to Installer Be sure to leave these instructions with the Consumer Note to Consumer Keep these instructions for future reference Skill level Installation of this appliance requires basic mechanical skills Completion time Approximately 1 hour We recommend that two people install this product Proper installation is the responsibility of the installer Product failure due to improper installation is not covered under the Warranty You MUST use all supplied parts and use proper installation procedures as described in these instructions when installing this air conditioner window REQUIREMENTS Your air conditioner is designed to install in standard double hung windows with opening widths of 23 to 36 inches 584 mm to 914 mm OFFSET EXTERIOR WALL 23 to 36 INTERIOR WALL A CAUTION Do not under any circumstances cut or remove the third ground prong from the power cord Do not change the plug on the power cord of the air conditioner Aluminum ho
7. Auto Cool O O tow Dry O O Med ean O Hien O DO THIS Press the Mode button NOTE The unit will automatically initiate the Energy Saver function under Cool Dry and Auto only Auto Cooling and Auto Fan modes NOTE UP DOWN button Press or hold either Up A or Down button until the desired temperature is seen on the display This temperature will be automatically maintained anywhere between 62 F 17 C and 86 F 30 C If you want the display to read the actual room temperature see To Operate on Fan Only section NOTE FAN button There are four 4 fan speeds Auto Low Med or High Each time the button is pressed the fan speed mode is shifted On Dry mode the fan speed is controlled at low automatically NOTE MODE button To choose operating mode press the Mode button Each time you press the button a mode is selected in a sequence that goes from Auto Cool Dry and Fan The indicator light will be illuminated and remain on once the mode is selected The unit will automatically initiate the Energy Saver function under Cool Dry and Auto only Auto Cooling and Auto Fan modes To operate on Auto feature When you set the air conditioner in Auto mode it will automatically select cooling or fan only operation depending on what temperature you have selected and the room tem
8. For safety reasons all four 4 screws MUST be securely fastened INSTALL THE ACCORDION PANELS NOTE Top rail and sliding panels at each side are offset to provide the proper pitch to the rear of 5 16 This is necessary for proper condensed water utilization and drainage If you are not using the side panels for any reason this pitch to the rear must be maintained Em lt A Place unit on floor a bench or a table Hold the accordion panel in one hand and gently pull back the center to fill the open end See Fig 1 Fig 1 INSTALLATION INSTRUCTIONS CONTINUED Slide the free end I section of the panel directly into the cabinet as shown in Fig 2 Slide the panel down Be sure to leave enough space to slip the top and bottom of the frame into the rails on the cabinet l section Fig 2 Once the panel has been installed on the side of the cabinet make sure it sits securely inside the frame channel by making slight adjustments Slide the top and bottom ends ofthe frame into the top and bottom rails of the cabinet Fig 3 E Rail E a Fig 3 D Slide the panel all the way in and repeat on the other side Top Rail T right Top left Bottom Rail Fig 4 NOTE If storm window blocks AC see Fig 11 11 o SECURE THE ACCORDION PANELS A K
9. Gurgling or hissing noise may be heard due to refrigerant passing through evaporator during normal operation NOTE All of the pictures in this manual are for explanatory purposes only The actual shape look of the air conditioner purchased may be slightly different but the operations and functions are similar AIR CONDITIONER FEATURES ELECTRONIC CONTROL UNIT CONTROLS OPERATING INSTRUCTIONS DISPLAYS TEMPERATURE ADJUSTS TEMP TIMER OR TIME OR ERROR CODES TEMPERATURE ics SEE Rhume Before you begin thoroughly familiarize OR TIME yourself with the control panel as shown to the right and all its functions Then follow ACTIVATES the symbol for the functions you desire The TIMER unit can be controlled by the unit controls 3 CHECK FILTER SLEEP MODE alone or with the remote control RESET BUTTON SETS MODE SETS FAN SPEED REMOTE SIGNAL RECEPTOR ENERGY SAVER MODE TURNS UNIT ON OR OFF FOLLOW ME INDICATOR Follow on some models Me AIR CONDITIONER FEATURES CONTINUED NOTE The following instructions represent the Unit Controls The same instructions can be used for the Remote Control TO TURN UNIT ON DO THIS Press the On Off button TO CHANGE TEMPERATURE SETTING TEMP TIMER DO THIS Press to adjust temperature setting TO ADJUST FAN SPEEDS DO THIS Press Fan to select fan speed TO SELECT THE OPERATING MODE Auto O O
10. HIND DECORATIVE FRONT AIR CONDITIONER CYCLING ON AND OFF TOO FREQUENTLY OR NOT ENOUGH UNIT WILL NOT TURN ON UNIT BLOWS FUSES OR POPS CIRCUIT BREAKER AIR CONDITIONER IS MAKING NOISES WATER PUDDLES INSIDE UNIT OR IS COMING INTO ROOM WATER DRIPPING OUTSIDE REMOTE SENSING FOLLOW ME DEACTIVATING PREMATURELY Possible Solutions Be sure unit is not too large or too small for the area of the room e Verify that all doors windows curtains and any other openings are closed off Verify nothing is obstructing the front grille of unit such as curtains etc Allow enough time for room to cool especially if outside temp is very high e Check that the filter is not dirty and louvers are open all the way and blowing in the direction desired Check that unit is set to Cool Mode and that temperature is down enough but not too low e f unit is near a heat source such as a stove etc then relocate unit e f air coming from unit is cool to the touch then unit is working properly please double check the first three bullet points above e f using Follow Me remote feature move remote away from unit Temperature sensor behind air filter touching cold coil These two elements should not be touching Carefully straighten tube away from coil Unplug unit for at least 5 minutes Follow Reset instructions on plug Outdoor temperature is below 64 F 18 C To defrost the coil set to Fan Only mode Air filter may
11. Your Source for Home Comfort C Perfect re 5 000 BTU WINDOW AIR CONDITIONER USER MANUAL J ho FOR MODELS t PES5000 E Iz 4 22 2 i aem c Before using your window air conditioner please read this manual carefully and keep it for future reference along with your receipt CONTENTS SAFETY PRECAUTIONS eesisisitctsscannssedcdiaiencuwesedasiaeercneinceuddia nl x Orio ddas C caa 2 IMPORTANT SAFETY INSTRUCTIONS eene nennen nnns 4 NORMAL SOUNDS iscisursisinic t kkkkmixkinks Susan dn nias ua V EE DUS AREE RUE ra cv diis 5 AIR CONDITIONER FEATUNRDES 5 doris emassa eo tva Rr rii ava rok aaa agli 5 INSTALLATION INSTRUCTIONS ios csiscecewti viia liec ciii a da cac cb rv va eia rivi 9 CARE AND CLEANING iiic xanax tad x xxx ARRA ERE E ER vxuaxS xis Eu HM iHd rn 13 TROUBLESHOOTING TIPS ia iixiix cios euch ossau cpu Donors Yarro tiirb XR S ER eR prre aes kta ees 14 This manual provides the information needed for proper use and maintenance of this air conditioner Basic preventative care can help extend the life of this unit The Troubleshooting Tips section in this manual contains a chart with solutions to the most common problems Referring to this section may save time and prevent the need for a service call in the event of a problem N CAUTION eContact an authorized service technician for repair or maintenance of this unit eContact an installer for installation of this unit if n
12. be dirty Clean filter Refer to Care and Cleaning section To defrost set to Fan Only mode Thermostat is set too cold for night time cooling To defrost the coil set to Fan Only mode Then set temperature to a higher setting Be sure unit is not too large or too small for the area of the room Remove grille and make sure the temperature sensor is not too close to the coils These two elements should not be touching Carefully straighten tube away from coil e Make sure nothing is blocking the grille or side vents e Make sure there is no dirt or debris inside the unit or on the filter Reset circuit breaker Make sure there are not too many items ie lamps TV s etc working off the same breaker e Check plug connection e f plug is operating on an on off switch be sure that the switch is on Try plugging unit into another outlet Unplug unit for at least 5 minutes Follow Reset instructions on plug e Make sure there are enough available amps on the circuit for the air conditioner e Large units which run on a 230v will require a dedicated 20 or 30 amp circuit Check to be sure the unit is free from debris such as leaves sticks etc Verify nothing is obstructing the unit e Check the fan blade for cracks or chips e Make sure the unit is properly and securely mounted inside the window or wall Clean the air filter Adjust the slope of the unit so that it drains downward toward the exterior of the ho
13. ce a click as the button engages RESET 4 The power supply cord is now supplying electricity to the unit On some products this is also indicated by a light on the plug head TEST ES NOTE Some plugs have buttons on the top NOTES Do not use this device to turn the unit on or off Always make sure the RESET button is pushed in for correct operation The power supply must be replaced if it fails to reset when either the TEST button is pushed or it cannot be reset f power supply cord is damaged it cannot be repaired Please call customer service to assist with replacement NOTE This air conditioner is designed to be operated under conditions as follows Outdoor temp 18 43 C 64 109 F 18 52 C 64 125 F for special tropical models Indoor temp 17 32 C 62 90 F Cooling operation If the unit is operated beyond the conditions specified above it may cause a failure of the unit NORMAL SOUNDS High Pitched Chatter High efficiency compressors may have a high pitched chatter Vibration during the cooling cycle Unit may vibrate and make noise because of poor wall or window construction or incorrect installation Sound of Rushing Air Atthe front of the unit you may hear the sound of rushing air being moved by the fan Pinging or Switching Droplets of water hitting condenser during normal operation may cause pinging or switching sounds Gurgle Hiss
14. cess heat generation eDoing so may cause electric shock or fire due to heat generation eincorrect grounding may cause electric shock eFailure to do so may cause fire and electric shock S eDoing so may cause fire fire and burns Failure to do so may cause explosion A A WARNING G Doing so may cause electric shock or fire due to heat generation Doing so may cause electric shock Doing so may cause failure of machine or electric shock e Doing so may cause fire and electric shock S eDoing so may cause fire and electric shock Doing so may cause electric shock or fire If the power cord is damaged it must be replaced by the manufacturer or an authorized service center or a similarly qualified person in order to avoid a hazard This could cause health issues eincorrect installation may cause fire and electric shock 8 eDoing so may cause electric shock Doing so may cause failure and electric shock Doing so may cause an explosion or fire A CAUTION When removing air filter do not touch metal parts of the unit electric shock Unit and Circuit breaker fuse must be switched OFF when cleaning direct air flow may cause fire and electric shock and may cause an injury L Stop operation and close the window in severe storms or hurricanes Operation with windows open
15. densation must be allowed to drain out Removing AC From Window e Turn AC off and disconnect power cord e Remove sash seal from between windows and Fig 8 eet d unscrew safety sash lock C To secure lower sash in place attach right e Remove screws installed through frame and angle sash lock with 3 4 19 mm or 1 2 frame lock 12 7 mm screw as shown Fig 9 e Close slide side panels into frame e Keeping a firm grip on air conditioner raise sash and carefully remove e Be careful not to spill any remaining water while lifting unit from window Store parts WITH air conditioner SASH Storm window 4 1 2 min Board frame or other 38 mm thickness obstruction as required oii Y for proper D Cut Window sash seal foam and insert itin the I pitch to rear space between the upper and lower sashes A ae entire Fig 10 sill Fasten g 0 with nails or screws FOAM SEAL Fig 11 12 CARE AND CLEANING N CAUTION Clean air conditioner occasionally to keep it looking and operating like new Be sure to unplug the unit before cleaning to prevent shock or fire hazards Air Filter Cleaning The air filter should be cleaned at least every two weeks or as necessary Trapped particles in the filter can build up and cause an accumulation of frost on the cooling coils Remove the
16. ecessary eThe air conditioner is not intended for use by young children without supervision Young children should be supervised to ensure that they do not play with the air conditioner eDisabled persons may require assistance with set up elf the power cord is to be replaced replacement work should be performed by authorized personnel only einstallation and repair work must be performed in accordance with the national wiring standards by authorized personnel only eDo not operate your air conditioner in a wet room such as a bathroom or laundry room NOTE All the illustrations in this manual are for explanation purposes only Unit purchased may be slightly different The design and specifications are subject to change without prior notice for product improvement Contact customer service for details SAFETY PRECAUTIONS To prevent injury to the user or other people and property damage the following instructions must be followed Incorrect operation due to ignoring of instructions may cause harm or damage The seriousness is classified by the following indications A N WARNING This symbol indicates the possibility of death or serious injury C N CAUTION This symbol indicates the possibility of injury or damage to property E Meanings of symbols used in this manual are as shown below Q Never do this 0 Always do this J Failure to do so may cause electric shock or fire due to ex
17. eeping a firm grip on the air conditioner carefully place the unit into the window opening so the bottom of the air conditioner frame is against the window sill Fig 5 Carefully close the window behind the top rail of the unit Measure from the cabinet edge About 5 8 to 3 4 Fig 5 INSIDE C OUTSIDE Wooden Windows NOTE Check that air conditioner is tilted back about 5 8 to 3 4 tilted about 3 to 49 downward to the outside After proper installation condensation should not drain from the overflow drain hole during normal use correct the slope otherwise B Extend the side panels out against the window frame Fig 6 window frame Fig 6 Q INSTALL SUPPORT BRACKET A Place the frame lock between the frame extensions and the window sill as shown in Fig 7 Drive 3 4 19 mm or 1 2 12 7 mm locking screws through the frame lock and into the sill NOTE To prevent window sill from splitting drill 1 8 3mm pilot holes before driving screws Se m N NIE Fig 7 INSTALLATION INSTRUCTIONS CONTINUED B Drive 3 4 19 mm or 1 2 12 7 mm If AC is Blocked by Storm Window locking screws through frame holes into window sash Fig 8 Add wood as shown in Fig 11 or remove storm window before air conditioner is installed If Storm Window Frame must remain be sure the drain holes or slots are not caulked or painted shut Accumulated rain water or con
18. ical shock serious injury or death Observe all local governing codes and ordinances Do not under any circumstances remove the power supply cord grounding prong NOTE If codes permit and a separate grounding wire is used it is recommended that a qualified electrician determine that the grounding path is adequate and not interrupted by plastic non metallic gaskets or other insulating materials Receptacle Wiring Receptacle wiring should be a minimum of 14 gauge Use copper wire only It is your responsibility to provide proper and adequate receptacle wiring installed by a qualified electrician Electrical Requirements A time delay fuse or time delay circuit breaker is also required A separate circuit serving only this appliance MUST be provided IMPORTANT SAFETY INSTRUCTIONS Ne The power supply cord with eS For Your Safety this air conditioner contains a current DO NOT store or use gasoline or other flammable vapors or liquids in detection device designed to reduce the vicinity of this or any other appliance the risk of fire Avoid fire hazard or electric shock DO NOT use an extension cord or Please refer to the section Operation an adaptor plug DO NOT remove any prong from the power cord of Current Device below for details In the event that the power supply cord is damaged it MUST be replaced by ENING Electrical Information an authorized repairman e Be sure the electrical service
19. me See Installation Instructions e Make sure that there is no debris blocking the drainage area of the unit Unit is removing a large quantity of moisture from a humid room This is normal during excessively humid days Remote control not located within range Place remote control within 20 ft and 180 radius of the front of the unit Remote control signal obstructed Remove obstruction NOTE A highly recommended troubleshoot for any issue in general consists of turning off unit and unplugging for 5 minutes It is also recommended to try another wall outlet 14 ere Your Source for Home Comfort Distributed by Perfect Aire LLC 5151 Belt Line Rd Suite 878 Dallas TX 75254 877 365 6274 www perfectaire us Specification and performance data is subject to change without notice Printed in PRC
20. minates It indicates the Auto Stop program is initiated Turning the unit on or off at any time or adjusting the timer setting to 0 0 will cancel the Auto Start Stop function 7 AIR CONDITIONER FEATURES CONTINUED CHECK FILTER FEATURE TEMP TIMER DO THIS Press Check Filter button O On O off Check Filter FOLLOW ME FEATURE on some models Light flashing DISPLAYS TEMP TIMER Displays NOTE If the unit breaks off unexpectedly due to power being cut it will restart with the previous function setting automatically when the power resumes NOTE CHECK FILTER button This feature is areminder toclean theAir Filter for more efficient operation The LED light will illuminate after 250 hours of operation To reset after cleaning the filter press the Check Filter button and the light will go off NOTE FOLLOW ME indicator light This feature can ONLY be activated from the remote control The remote control serves as a remote thermostat allowing for precise temperature control at its location To activate the Follow Me feature point the remote control towards the unit and press the Follow Me button The remote displays the actual temperature at its location The remote control will send this signal to the air conditioner every 3 minutes until the Follow Me button is pressed again If the unit does not receive the Follow Me signal during
21. perature The air conditioner will control room temperature automatically around the temperature you set In this mode the fan speed cannot be adjusted It starts automatically at a speed according to the room temperature If the room does not get too warm it will stay at Low speed AIR CONDITIONER FEATURES CONTINUED TO USE THE ENERGY SAVER FEATURE SLEEP FEATURE TEMP TIMER Qon O oft M Timer TIMER AUTO START STOP FEATURE TEMP TIMER MLIA DOTHIS Press the Energy Saver button DO THIS Press Sleep button DO THIS Press Timer button To operate on Fan only not available on all models Use this function only when cooling is not desired such as for room air circulation or to exhaust stale air Remember to open the vent during this function but keep it closed during cooling for maximum cooling efficiency You can choose any fan speed you prefer During this function the display will show the actual room temperature not the set temperature as in the cooling mode To operate on Dry mode In this mode the air conditioner will reduce air humidity If the space is a closed or sealed area some degree of cooling will continue NOTE ENERGY SAVER button This function is available on Cool Dry and Auto only Auto Cooling and Auto Fan modes In this mode the fan will continue to run for 3 minu
22. tes after the compressor shuts off The fan then cycles on for 2 minutes at 10 minute intervals until the room temperature is above the set temperature at which time the compressor turns back on and cooling starts NOTE SLEEP button In this mode the selected temperature will increase cooling or decrease heating units with heater only by 2 F 1 C 30 minutes after the mode is selected The temperature will then increase cooling or decrease heating units with heater only by another 2 F 1 C after an additional 30 minutes This new temperature will be maintained for 6 hours before it returns to the originally selected temperature This ends the Sleep mode and the unit will continue to operate as originally programmed The Sleep mode program can be cancelled at any time during operation by pressing the Sleep button again NOTE TIMER button First press the Timer button The indicator light beside the word On will illuminate indicating the Auto Start program is on Press or hold the Up or Down Temp Timer arrows to change the Auto time by 0 5 hour increments up to 10 hours then at 1 hour increments up to 24 hours The control will count down the time remaining until start The selected time will register for 5 seconds and the system will automatically revert back to display the previous temperature setting When the Timer On is displayed press the Timer button again and the Timer Off indicator light illu
23. use wiring may present special problems consult a qualified electrician When handling unit be careful to avoid cuts from sharp metal edges and aluminum fins on front and rear coils TOOLS YOU WILL NEED Phillips Screwdriver Level TOOLS YOU MAY USE Screwdriver Pencil Ruler or tape measure Scissors or knife NOTE Save carton and these Installation Instructions for future reference The carton is the best way to store unit during winter or when not in use INSTALLATION INSTRUCTIONS CONTINUED PREPARE THE WINDOW Lower sash must open sufficiently to allow a clear vertical opening of 13 inches 330 mm Side louvers and the rear of the AC must have clear air space to allow enough airflow through the condenser for heat removal The rear of the unit must be outdoors not inside a building or garage Mounting Hardware gs m9 254 3 4 or 1 2 Lock Frame Sash Lock Window sash Screws 2 1 7 seal foam 1 PREPARE AIR CONDITIONER A Remove the air conditioner from the carton and place on a flat surface B Remove top rail from the rear of the packaging material as shown in Fig A Top Rail Hardware T or Oey 3 8 Screws 4 Top Rail 1 Packaging C Align the hole in the top rail with those in the top of the unit as shown in Fig B D Secure the top rail to the unit with the 3 8 screws as shown in Fig C NOTE
Download Pdf Manuals
Related Search