492 Kb Manual_L16
Contents
1. 5 _ TBE FEES RAHE EGEE olll E oja SLR SLR we le RS QUADRO L16 comes with an easy to navigate system menu This next section will detail the functions of each command in the system menu To access the main menu press the ESC button Tap the UP or DOWN buttons until you reach function you wish to change When you reach the function you wish to change press the ENTER button When a function is selected use the UP or Down buttons to change the function settings Once your changes are made press the ENTER button Addr DMX Address Setting via control board and motor setting Tap the ESC button and UP button or DOWN button until Addr is displayed press ENTER will now be displayed represents the displayed address Press the UP or DOWN buttons to find your desired address Auto This menu will let you select your desired auto mode Tap the ESC button and UP button or DOWN button until Auto is displayed press ENTER Autx will now be displayed you can confirm three modes by UP DOWN for auto mode Chnd This menu will let you select your desired DMX Channel mode Tap the ESC button and UP button or DOWN button until Chnd is displayed press ENTER Ch will now be displayed represents the displayed DMX channel mode Press the UP or DOWN buttons to find your desired Channel mode CoLo This menu will let you select your desired sound mode Tap t2. LIGHTING PROFESSIONAL LED COLOR CHANGER USER MANUAL Melis 190 See 0 909 L TE THIS MANUAL FOR FUTURE NEEDS CE Thank you for using QUADRO L 16 For the sake of safety and better operation of this projector please read this manual carefully before using and operating it lest incur any personal injury or damage to the projector SAFETY INSTRUCTIONS CAUTION careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual gt gt Important Damages caused by the disregard of this user manual are not subject to vvarranty The dealer vvill not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not svvitch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class I Therefore it is essential that the device be earthed The electric connection must carry out by qualified person No move at operating mode Make sure that the avai
3. e device was designed for indoor use Lighting effects are not designed for permanent operation Consistent operational breaks may ensure that the device will function properly for a long time Do not shake the device Avoid brute force when installing or operating the device The device shall only be used complete with its protective shield While choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust The minimum distance between light output from the projector and the illuminated surface must be more than 0 1 meter Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported For safety reasons please be aware that all modifications on the device are forbidden If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to short circuit burns electric shock crash etc INSTALLATION INSTRUCTIONS Mounting the device CAUTION Please consider the EN 60598 2 17 and the other respective national norms during the installation The installation must only be carried out by a qualified person The applicable temperature for the lignting is bet
4. he ESC button and UP button or DOWN button until CoLo is displayed press ENTER Either CoL X X representing a number between 1 9 or AtF will be displayed Press the UP or DOWN buttons to select either a static color or mode If you select a static color press ENTER and it will be confirmed AtF Make your own color by mixing and adjusting the red blue and green manually Select AtF press ENTER red Gree or blue will be displayed Red is first press ENTER then you can adjust it between 1 255 press ESC you can select other color by UP or DOWN and then press ENTER to adjust it SoUn This menu will let you select your desired sound mode Tap the MENU button until Soun is displayed press ENTER Soux will now be displayed You can confirm three modes by UP or DOWN for sound mode SLAv This menu will let you select your desired Master slave mode Tap the MENU button until SLav is displayed press ENTER Sla will now be displayed Slave mode is confirmed It will be slaved by auto mode sound mode and chase mode VEr This will display the software version the MENU button until VER is displayed Press the ENTER button and the software vesion will be displayed Press the MENU button to leave this function Universal DMX control mode Each function of this machine can be controlled by a standard DMX 512 console DMX controller allovys you t
5. lable voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more than 0 1m distance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard CAUTION Never touch the device during operation The housing may heat up CAUTION Never look directly into the light source as sensitive persons may suffer an epileptic shock Please be aware that damages caused by manual modifications to the device are not subject to warranty Keep away from children and non professionals GENERAL GUIDELINES This device is a lighting effect for professional use on stages in discotheques theatres etc This fixture is only allowed to be operated with the max alternating current which stated in the technical specifications in the last page of this manual th
6. o create unique programs tailored to your individual needs Quadro L16 can work with six configurable channel modes See the channel chart below 14 ae mode mode mode mode mode mode I SS Green 1116132114 ee Control channel 1 1 1 1 Dimmer intenal programs and functions see belovr 2 2 2 2 Speed see below DMX value and function LED 0 7 8 15 16 23 24 31 237 244 245 242 242 247 248 255 function Dimmer Strobing Mode2 Mode27 Sound1 Sound2 Sound3 Function Speed TECHNICAL SPECIFICATIONS Model QUADRO L16 Voltage 100V 240V 50Hz 60Hz LEDs 16 x 3W 3 in 1 LEDs Power Consumption80W Fuse lAmp Weight 5 3Kg Dimensions 965 x 64 x 153mm Colors RGB Color Mixing DMX Channels 3 5 8 14 24 amp 26 DMX Channel Modes
7. ween 0 C 45 C Do not use the lighting under or above the temperature The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment an appropriate safety rope Never stand directly below the device when mounting removing or servicing the fixture The operator has to make sure the safety relating and machine technical installations are approved by an expert before taking the device into operation for the first time These installations have to be approved by a skilled person once a year Cautions The effect should be installed outside areas where persons may reach it walk by or be seated Overhead mounting requires extensive experience including amongst others calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury CAUTION The electric connection must only be carried out by a qualified electrician Before mounting make sure that the installation area can hold a minimum point load of 10 times the device s weight Connect the fixture to the mains with the power plug On Board System Menu Atl tli RUE 10100 6 5 SE EF
Download Pdf Manuals
Related Search