Manual - ArtFox Lighting
Contents
1. is showing on the display Use DOWN and UP button to change the DMX512 address Once the address has been selected to go back to the functions without any change press the FUNCTION button again Please refer to the following diagram to address your DMX512 channel for the first 4 units 1 CHANNEL MODE 1 2 3 4 6 CHANNELMODE 1 7 13 19 12 CHANNEL MODE 1 13 25 27 5 DMX512 Configuration SHORT MODE 1 CH Number Channel DMX Value Description 0 7 Blackout 8 69 Show1 from slow to fast 1 SHOW 70 131 Show2 from slow to fast 132 193 Show3 from slow to fast 194 255 Show4 from slow to fast STANDARD MODE 7 CHs Number Channel DMX Value Description 1 Tilt 1 0 255 Tilt 1 move 15 to 165 degree 2 Tilt 2 0 255 Tilt 2 move 15 to 165 degree 3 Dimmer All 0 255 All dimmer 0 to 100 0 9 Blackout 4 Strobe 10 250 Strobe from slow to fast 251 255 Open 0 7 Blackout 8 22 Chase 1 23 37 Chase 2 38 52 Chase 3 53 67 Chase 4 68 82 Chase 5 83 97 Chase 6 98 112 Chase 7 113 127 Chase 8 5 Led chase 128 142 Chase 9 143 157 Chase 10 158 172 Chase 11 173 187 Chase 12 188 202 Chase 13 203 217 Chase 14 218 232 Chase 15 233 247 Cha2. when one of the units power is disconnected 3 At last fixture the DMX cable has to be terminated with a terminator to reduce signal errors Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last fixture 4 Each lighting fixture needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually O 1 are equal to 1 5 3 pin XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 11 7 Troubleshooting Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The fixture does not work no light 1 Check the connection of power and main fuse 2 Measure the mains voltage on the main connector B Not responding to DMX controller 1 Check DMX connectors cables to see if link properly 2 Check the address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the fixture or the previous one 4 Try to use another DMX controller 5 Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit C No response to the sound 1 Make sure the fixture does not receive DMX signal 2 Check microphone to see if it is good by tapp
3. SOE ser Manual Please read the instruction carefully before use CONTENTS de Safetv N trueto Sarria didas 3 2 Technical SPRINT A ad 4 3 HOW TO Set The Dn iCal oia 5 3 Rear ns 5 3 2 M in FUNCION a araa oaae AA RREA EAA EEEE eqe EEEa EEE 5 A OW toControlthe Uniten iaa anal 6 4 1 Master Slave Built In Preprogrammed Functi0ON cccococccccononancninnnananacinanananoss 7 4 2 DMX Controles ota 7 5 DMX512 Configuratio AAA SAS 9 6 DMX Connectio Nesic a a IN R AT E a N 11 Js TOMES ADO 0 iS E E 12 8 Fixture CANA A td 13 1 Safety Instructions Please read the instructions carefully which includes important information about the installation operation and WARNING maintenance PLEASE keep this User Manual for future consultation If you sell the fixture to another user make sure that they also receive this instruction booklet e PLEASE unpack and check carefully there is no transportation damage before using the fixture e It s important to ground the yellow green conductor to earth in order to avoid electric shock PLEASE disconnect main power before servicing and maintenance e Maximum ambient temperature is Ta 40 C DO NOT operate it where the temperature is higher than this e Unit s surface temperature may reach up to 85 C DO NOT touch the housing bare handed during its operation e In the event of serious operating problem stop using the fixture immediately Never try to repair the fixture by yours
4. elf Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts e DO NOT connect the device to any dimmer pack e DO NOT touch any wire during operation and there might be a hazard of electric shock e To prevent or reduce the risk of electrical shock or fire do not expose the fixture to rain or moisture e The housing must be replaced if they are visibly damaged Warning e To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture e DO NOT open the unit within five minutes after switching off e The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged Caution For 230V 50Hz power supply maximum fixtures that can be connected together from the same mains outlet is 8 For 120V 60Hz power supply maximum fixtures that can be connected together from the same mains outlet is 4 Installation The unit should be mounted via its screw holes on the bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating And make sure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit s weight Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture The equipment must be fixed by p
5. ing the microphone D One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition 12 8 Fixture Cleaning The cleaning must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics e Clean with soft cloth using normal glass cleaning fluid e Keep the lights and parts at dry condition 13
6. ply power to the next unit To select any functions press the ENTER button until the required function is showing on the display Select the function by pressing the ENTER button and the display will blink Use the DOWN and UP button to change the mode Once the required mode has been selected press the ENTER button to setup to go back to the functions without any changes press the ENTER button again Press the FUNCTION button exit the menu mode The main functions are shown below LEVEL 1 LEVEL 2 LEVEL 3 LEVEL 4 BEAM V8 Addr 001 BEAM V8 A Auto BEAM V8 M Auto BEAM V8 A Music BEAM V8 M Music BEAM V8 Slave Address Address 001 Reset Reset NO Reset YES Manual Manual Tilt 1 Tilt 1 000 Manual Tilt 2 Tilt 2 000 Manual Dimmer Dimmer 000 Manual Strobe Strobe 000 Mode Mode DMX Mode DMX Short DMX Mode Standard DMX Mode Extended Mode Auto Auto Alone Auto Master Mode Music Music Alone Music Master Mode Slave Option Option Display Display Delay Off Display Always Option Lost DMX Lost DMX Clear Lost DMX Hold Advanced Advanced Code Code 000 NOTE 008 Advanced Adjust Tilt 1 Adjust Tilt 1 000 Adjust Tili 2 Tilt 2 000 Adjust Dimmer 1 Dimmer 1 000 Adjust Dimmer 2 Dimmer 2 000 Adjust Dimmer 3 Dimmer 3 000 Adjus
7. rofessionals And it must be fixed at a place where is out of the touch of people and has no one pass by or under it 2 Technical Specification e Spider an innovative versatile pixel multi beam effects delivering outstanding sharp and long throw beams e Featuring 2 movable LED bars each with 4 pixel controlled 10W LEDs for the best lighting performance you can ever except e 3 Operation Modes DMX Mater Slave mode Sound Activation e DMX Channel modes 1 6 12 channels e Great built in programs e Electronic dimming and various strobe effects e Ideal for pubs clubs bars parties Mobile DJs and anywhere else you could possibly imagine e Input Voltage AC 100 240V 50 60Hz e Power Consumption 90 W e LED 8 x 10W white LEDs e Dimension 395 x234 x138mm 4 1 Button FUNCTION To return to the upper menu one by one DOWN UP To browse or change through the various Setup Options and change values Add or subtract ENTER To select the functions save your settings or enter the next menu LCD Display Menu Used to show the various menus and the selected functions DMX IN OUT For DMX512 links use 3 pin XLR plug cable to link the unit together Pothook Used to hook the safety cable Fuse T 3 15A Used to protect the unit from the damage of the over current POWER IN Used to connect to supply power nN Oo WwW Bb WU N POWER OUT Used to connect to sup
8. se 16 248 255 Full on 6 Chase speed 0 255 Speed from slow to fast EXTENTED MODE 13 CHs Number Channel DMX Value Description 1 Tilt 1 0 255 Tilt 1 move 15 to 165 degree 2 Tilt 2 0 255 Tilt 2 move 15 to 165 degree 3 Dimmer All 0 255 All dimmer 0 to 100 0 9 Blackout 4 Strobe 10 250 Strobe from slow to fast 251 255 Open 5 Led1 0 255 Dimmer LED1 from 0 to 100 6 Led2 0 255 Dimmer LED2 from 0 to 100 7 Led3 0 255 Dimmer LED3 from 0 to 100 8 Led4 0 255 Dimmer LED4 from 0 to 100 9 Led5 0 255 Dimmer LED5 from 0 to 100 10 Led6 0 255 Dimmer LED6 from 0 to 100 11 Led7 0 255 Dimmer LED7 from 0 to 100 12 Led8 0 255 Dimmer LED8 from 0 to 100 6 DMX Connection Tanaan WOOO DMX OUT COMMON DMX DMX INPUT Cs DMX OUTPUT DMX Termination reduces signal errors and to avoid signal E transmission problems and interference It is always advisable to connect a DMX terminal X Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture 1 Connect the fixture together in a daisy chain by XLR plug cable from the output of the fixture to the input of the next fixture The cable cannot be branched or split to a Y cable Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 2 The DMX output and input connectors are pass through to maintain the DMX circuit
9. t Dimmer 4 Dimmer 4 000 Adjust Dimmer 5 Dimmer 5 000 Adjust Dimmer 6 Dimmer 6 000 Adjust Dimmer 7 Dimmer 7 000 Adjust Dimmer 8 Dimmer 8 000 Advanced Mic Sens Mic Sens 080 View View Hours Reset H Hours 00000 H NO Reset H YES View CH 001 Dmx Value DMX 000 View 1 00F Version YYYY MM Default Load Def NO Load Def YES 4 How to control the units You can operate the unit in two ways 1 By master slave built in preprogram function 2 By DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be affected at once Each time you turn the unit on it will show Stage Light on the display After that the unit will be ready to receive DMX signal or run the built in programs 4 1 Master Slave Built In Preprogrammed Function By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an instant show You have to set the first unit in AUTO mode and select Master The other units will have to select Slave mode their DMX cables plugged into the DMX input jacks daisy chain 4 2 DMX Controller Using a universal DMX controller to control the units you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal Press the ENTER button up to when the Address
Download Pdf Manuals
Related Search