Manual - Hunt Electronic USA
Contents
1. HTC 65GNV HIGH RESOLUTION HTC 65CNV MED RESOLUTION DAY amp NIGHT CCD CAMERA SPECIFICATOINS ITEM NO HTC 65C HTC 65G PICK UP DEVICE CCD IMAGE SENSOR 1 3 ELEMENTS H V NTSC 512 492 PAL 512 582 NTSC 771 492 PAL 753 582 HORIZONTAL RESOLUTION More than 400 TV Lines More than 540 TV Lines SYNCHRO FREQUENCY NTSC 15 734 kHz PAL 15 625 kHz CLOCK FREQUENCY NTSC 59 94Hz PAL 50Hz SCANNING SYSTEM 2 1 INTERLANCE SENSITIVITY D N 1 0 05 Lux F 1 2 2 0 08 Lux F 1 2 SYNCHRONIZATION LINE LOCK S N RATIO MORE THAN 50 dB AGC Auto VIDEO OUTPUT 1 Vpp 75 Ohms Composite AUTO IRIS Video Driver DC Driver Switchable MOUNT LENS CS Mount POWER SUPPLY 24 VAC or 12VDC 10 POWER CONSUMPTION 3 5W for 24VAC AW for 24VAC AES ELECTRONIC SHUTTER Up to 1 100 000 sec linear ON OFF Switchable D N day amp night Normal image Day amp night ON OFF Switchable IR RAY acceptable 850 940nM INFREDRAD WAVE LENGTH DIMENSIONS mm 102 D 59 W 59 H WEIGHT 9 430 STORAGE TEMPERATURE 30 to 60 Degree C OPERATON TEMPERATURE 10 to 45 Degree C SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE ee In order to protect the camera avoid placing or using it under direct sunlight rain or dust Don t touch the CCD sensor directly with your fingers If necessary use soft cloth moistened2. with alcohol to wipe off the dust 3 When the camera is not in use keep the lens or cap being attached to protect the CCD sensor 4 DC model use a 12V regulated power source AC model directly connect to AC power source 5 Don t drop your camera or give it a strong shock or vibration raat adi Before connection make sure that power of all units are OFF and cords are unplugged a Mount a lens onto the camera 3 Connect a video terminal of the camera and the video input terminal of a monitor TV with a 75 Q coaxial cable 4 Connect the power terminal of the camera to a power supply Caution Installation should conform to all local codes Lens coaxial cable for video signal and power supply are not supplied with the camera LOCATIONS FUNCTION OF PARTS amp ACCESSORIES STEP Connect to a monitor TV V Connect a power source Adiust the back focus OPERATIONS AND ADJUSTMENTS 1 Connect the power cord and turn the power ON 2 Adjust the iris and focus of the lens to obtain the optimum image Using normal lenses CS mount lens mode is the standard type When use C mount lens Please use the CS C conversion Ring Using the zoom lens adjustment of the back focus The camera is set at the standard back focus position when shipped from factory Depending on types of zoom lenses however slight adjustment may be necessary Adjust the lens back focus by turning the focusing kn
3. e For shooting fast moving objects or high brightness environment the various electronic shutter speed can change automatically 3 D N By setting the switch to ON the image is normal situation If you choose switch to OFF color image would change to black and white automatically under low light condition SWITCH ON ON OFF USAGE p 1 BLC YES NO BACK LIGHT COMPENSATION I 2 AES YES NO WHEN NOT USE THE IRIS LENS pi COLOR IMAGE WOULD CHANGE TO B W SDI NORMAL eae NUET IMAGE UNDER LOW LIGHT CONDITION LINE LOCK When two or more cameras are switched by the video switcher quad or multiplexer for monitoring on a TV monitor The picture may fluctuate due to different AC line phase of each camera In this case please select the Line Lock function
4. ob in either direction 1 Place an object at any fixed distance and set the focus ring of the zoom lens to be used with 2 Set the zoom lens to fully TELE position and obtain the best focus Camer position by turning the focus ring of the zoom 3 Then set the zoom lens to fully WIDE position and obtain the best focus position by turning the focusing knob 4 Repeat the procedures 2 and 3 until focus remains in constant among the zoom range Using an auto iris lens NOTE Don t use both SHUTTER ON amp AUTO IRIS lens at the same time DC driver lens When auto iris lens is used set Al DRIVER switch to DC position and connect the plug of the lens for iris terminal to the IRIS terminal on the back of camera DC Drive Level When you use an DC Driver Lens you can adjust the DC Drive Level for the bright of video output Video Driver lens When auto iris is used X Ng Al DRIVER switch to VIDEO position and AX to connect the plug of the lens for iris terminal z s to the IRIS terminal on the back of the camera A V Dip Switch 1 BLC BACK LIGHT COMPENSATION As you take a picture with strong light behind the subject the picture would be looked very dim on the subject In this case you should select BLC ON to get a clear image NOTE When you select BLC ON than the SHUTTER should be in ON position or use Auto Iris Lens 2 AES By setting the AES switch to ON the AES mode Up to 1 100 000 sec is availabl
Download Pdf Manuals
Related Search