WR10 user manual - OrcaTorch Technology Limited
Contents
1. the main power and put the light with the battery into the cradle the light will automatically turn off and start charging It will stop charging when the battery is fully charged and the power indicator will turn from red to green The low mode will turn on directly when a power failure happens or when the light is taken out from cradle 4 Over heat protection WR10 will accumulate a lot of heat when working at turbo mode To avoid overheating the flashlight will automatically shift to the high mode after working at Turbo mode for 20 minutes Please press the side switch to shift back to the turbo mode if you want to use it continuously 5 Over discharge protection The light will automatically shift to the middle mode when the remaining power is less than 5 to protect from over discharge lf you are using low mode then it will be still at low mode And the power indicator will turn to red to remind you to have the battery charged or changed Press the side switch to obtain different function BATTERY REPLACEMENT 1 As shown in the figure insert the battery with the anode side toward the light head 2 Please do not reverse the battery to avoid damage to the flashlight and battery 3 Please do not use battery with higher voltage than the flashlight working voltage 4 Please do not use battery with damaged surface or deformation to avoid short circuit explosion leakage etc USAGE AND MAINTENANCE Please don t di2. OFCI NI OACI User manual WR IO max DJO ramens Patent No 201330274937 4 All Rights Reserved PRODUCT INTRODUCTION ORCATORCH WR10 is the first multifunctional flashlight with wireless charging technology and intelligent recognition control technology It features the wireless charging system and can automatically stop charging when fully charged to prevent from overcharging It will recognize the failure of power or the remove of the charging cradle and automatically turn on for emergency use With the candle mode design that makes it act as a small table lamp IPX 8 waterproof and intelligent power indicator design WR10 is a super All Rounder for home security emergency escape outdoor sports law enforcement as well as search and exploration PRODUCT FEATURES Cree XM L2 U2 LED max 950 lumens output Uses 1 26650 battery or 1 18650 with a battery sleeve The latest wireless charging technology convenient in charging The intelligent recognition and control technology automatically turn on for emergency lighting when the power failure is detected Support AC charging and DC charging Intelligent power indicator High efficiency constant current circuit constant brightness Over charge and over discharge protection function Over heat protection function Reverse polarity protection to protect from improper battery installation Anti roll slip resistant body design Aircraft grade high strength aluminum AL 6061 T6 w
3. ith premium Type Ill military hard anodized anti abrasive finish Alloy aluminum reflector with professional optical analysis Toughened glass with anti reflective coating TECHNICAL PARAMETERS OSEE o hn ne Ons ansinewaris Turoo High miaa tow strobe sos 3 45V Dimension 155 5mm Length x 35mm Diameter x 45mm Head C newem OOOO 2230 Cexcusingbatte Notice 1 Stated data has been measured according to the international flashlight test standards ANSI NEMA FL1 using one ORCATORCH 26650 Li ion battery 3 7V 4000mAh under laboratory conditions The parameters are approximate and may vary between flashlights batteries and environments 2 The flashlight will shift to the high mode automatically after working at Turbo mode for 20 minutes Therefore the runtime of Turbo mode is an accumulated time at Turbo output 3 The car charger input is 12V please do not plug it in the car power higher than 12 V OPERATION INSTRUCTIONS 1 ON OFF The default low mode will be on when the battery is inserted correctly you can press the side switch lightly to turn it off 2 Mode Selection When the flashlight is on press the side switch to switch mode among turbo high middle low and off Keep pressing the side switch for 2 3 seconds to get the hidden strobe mode press again to get the SOS mode then you can get back to the previous brightness mode by pressing again 3 Charge the battery Connect the charging cradle to
4. lashlight is high intensity lighting device and capable of causing eye damage please avoid shining the light directly into the eyes ORCATORCH TECHNOLOGY LIMITED Tel 86 755 33560383 Fax 86 755 29454989 Email info orcatorch com www orcatorch com Address 5th Floor Emerson Building A 26 Zone Baoan District Shenzhen city China 518101 www orcatorch com
5. sassemble the sealed head doing so may cause damage to the flashlight and will void the warranty We recommend the use of high quality batteries If the flashlight will not be used for a long time remove the batteries to avoid damage from electrolyte leakage or battery explosion Please replace the O rings if they are damaged after prolonged use and regularly lubricate the o rings so as to not erode the rubber Doing so will keep the flashlight properly sealed against water Please clean the contacts of your light from time to time especially when the light flickers or doesn t light up There are probably several reasons for a flickering or not working light Reason A The batteries need to be replaced Solution Replace batteries Please confirm correct installation of and terminals Reason B The threads PCB board contact or other contacts are dirty Solution Clean the contact points with an alcohol soaked cotton swab If the methods above don t work please contact the distributors and refer to the warranty policy PRODUCT WARRANTY We will replace products afflicted with manufacturing defects within 30 days of purchase and repair a light free of charge within 24 months of purchase if problems develop under normal use 12 months for accessories if repair is required after 24 months from the date of purchase we will charge for parts The total repair fee is dictated by the cost of the replaced materials Warning The f
Download Pdf Manuals
Related Search