how ZXT-120 works with Vera
Contents
1. Add configuration settings 3 Please select and a default setting interface will display Note ZXT 120 does not support multiple configuration settings please do it once at a time Configuration settings Variable Data Size Desired Value Current Value 4 The configuration variable refers to parameter number 27 for code selection the desired value refer to ZXT 120 code list e g Chigo there are 4 codes try 42 please enter parameter number 27 and value of 42 Data Size you can select either 2 byte dec or 4 byte dec both works Revision Date Oct 25 2013 Page 3 of 6 Remotec ZXT 120 Technology User guide for how ZXT 120 works with Vera Gateway Configuration settings Variable Data Size Desired Value Current Value 2 byte dec SS m SAVE Click x to close the page there will be a button on the upper right corner Click it VERA will send the configuration set to ZXT 120 ZXT 120 will flash twice if the configuration is received Flash 6 times if it failed Then you can go to the thermostat control UI to control your air conditioner if it does not work please do step 1 to step 4 above to select other codes If none of the codes works please use the same steps and same parameter number 27 to select parameter value OOO 000 is a reserved code number for learning Part3 Learning 1 Set the Variable and desired value as follows then close and save Configuration settings Variable2. Data Size Desired Value Current Value 2 Back to the setup page Look up the mapping table as below IR Learning Mapping Table Parameter number 25 Thermostat Parameter Value command Location amp IR setting OFF ON resume OoOo e eoa C o eeo eeg Revision Date Oct 25 2013 Page 4 of 6 Remotec ZXT 120 Technology User guide for how ZXT 120 works with Vera Gateway pefe 3 Input the Variable number of 25 which is used for learning and the value of 0 for OFF you can also refer to the user manual page 13 Then close and save Configuration settings Variable Data Size Desired Value Current Value 4 After saving it it will display the configuration tips in the top of the website Please note when the ZXT 120 flashes once you can press the on off key on the remote control make sure your remote is ON so when you press once it will send OFF command and vice versa when you want to learn ON make sure your remote is OFF fWWave Configuring Aave devices So INSTEON Mo INSTEON 5 Press the ON OFF or power button on the original remote towards ZXT 120 within 1 3 inches 1 3 inches X Original remote ZXT 120 LED flashes twice if it s successfully flashes 6 times if failed try again 6 Repeat the step 3 to 5 for leaning other settings according to the mapping table When you learn other settings with temperature make sure your original remote is set to the desire
3. Remotec ZXT 120 Technology User guide for how ZXT 120 works with Vera Gateway Vera to ZXT 120 User Guideline PART 1 Inclusion NOTE Please do exclusion before inclusion which is to make sure the ZXT 120 is not included in other network 1 Enter the Vera User Interface and go to PENSE i d INSTEON No INSTEON a micasaverde o Thursday 2498808012 16 07 Select gateway V ogin Register C5 Reload DASHBOARD DEVICES AUTOMATION APPS ACCOUNT ENERGY SETUP All Lights Climate Sensors Cameras Windows Security Mobile Phones AY Gear Other Add Devices New user Read Getting Started quide no room SZ Show Room 2 click 99 Devices You will enter the Add Devices page DASHBOARD DEVICES AUTOMATION APPS ACCOUNT ENERGY SETUP All Lights Climate Sensors Cameras Windows Securty Mobile Phones AW Gear Other Add Devices Hew user Read Getting Started guide First you need to add the devices you want me to control like light switthes door locks cameras and so on 4 You can select Advanced wave devices 5 Before adding device we highly recommend user to do exclude firstly as follows Any tepe of Z Wave device which you can bring clase to Vera Exclude node s of vpe E i Rite ana timeout after Bd Then Click and Vera will send excluding command Revision Date Oct 25 2013 Page 1 of 6 Remotec ZXT 120 Technology User guide for how ZXT 120 works with Vera Gateway 6 You sho
4. d settings and turned off then turn on it when learn it or set to 1 degree higher or lower so later when you learn it you can press the DONW or UP button once and it will go to your Revision Date Oct 25 2013 Page 5 of 6 Remotec ZXT 120 Technology User guide for how ZXT 120 works with Vera Gateway desired temperature setting when you learn it For example you and set your original remote to 19 Cool and turned off Or set to 18 C cool and press UP button when you learn or set to 20 C cool and press DOWN button After all learning completed user can go back to the ZXT 120 control page on the gateway for normal operation Remark on Vera control UI there is no Resume or ON button as it is not dedicated for air conditioner control It is for thermostat control Some users encountered that after learned successfully OFF works fine But when try to turn to COOL mode ZXT 120 flashes 6 times and no IR code sent out The work around will be turn the temperature to 19C or whatever you have learnt it will turn on the A C In ZXT 120 V1 5 we will try to solve this issue or it will be good if Vera will add a dedicated Key for RESUME or ON This only happens on learned code Built in code does not have this issue Revision Date Oct 25 2013 Page 6 of 6
5. uld press PROG once on the ZXT 120 when you see the info board in the top of the webpage as follows If it is successful to remove the device the info board will show 7 After excluding you can do the same way to include device Any toe of 7 WWwaye device which you can bring clase to vera Include vo nodes of type any full power w and timeout after BO Then Click and Vera will send including command 8 You should press PROG button on the ZXT 120 when you see the info board in the top of the webpage as follows If it is successful to remove the device the info board will show 9 Wait a minute while system is doing save Revision Date Oct 25 2013 Page 2 of 6 Remotec ZXT 120 Technology User guide for how ZXT 120 works with Vera Gateway PART 2 Code Selection 1 Please click setup in the bellow box SA Show Room _ Thermastat 5 50c Energy Auto On Normal aa qg pH Cool Cycle Heat 2 Select Device Options and you will see the configuration user interface _ Thermostat Room S Show Room Control settings Advanced Device Options Logs Notifications Anave options for device 18 learn more Manual Z Wave route advanced explain this Update Neighbor Modes Configuration settings Add configuration settings Associations You must leave auiorniatcaly configure on before this works learn more Group ID Es Add group
Download Pdf Manuals
Related Search