GSM-3E S & SK - SRS single button
Contents
1. GSM SIM not 3G or 4G only SIM If you are unsure contact your SIM card provider to verify Frequency of operation should be any one of the international quad band standards 850 900 1800 1900 MHz Check the reception is good Poor reception is not sufficient Check the antenna has been mounted as high as possible not near large metal objects or wet green shrubs etc Check the antenna connection Visually inspect that the centre pin inside the antenna is intact and has not been pushed back inside the fitting Q The unit calls the first number but there is not enough time to answer before it diverts to the next number A Increase the no answer time as per programming instructions Q The unit calls the first number but voicemail comes on before it can ring the second number A Decrease the no answer time as per programming instructions Q The caller ID part does not work A Be sure to program the caller ID part under 72 feature If your number is a private or number withheld then it will not work Even if you have already programmed a number to receive a call from the intercom if you also want that number to have caller ID access it must be programmed under the 72 feature also Ensure the number is entered as you would normally dial it from another phone Do not put the country code in front of the number Enter the country code in which the unit is operating in separate under the 71 feature International callers2. is default programmers code Note Pressing again will exit programming mode For most installations it is sufficient to add a single keypad code for all users However you can program up to 99 codes for relay 1 and 10 codes for relay 2 To do this you need to first put the unit into multi mode 9 0 0 Set to SINGLE USER mode and refresh system 9 0 Set to MULTI USER mode and refresh system Programming User codes for SINGLE USER mode 0 Enter NEW MASTER programming code Enter user code for relay 1 Enter user code for relay 2 Programming User codes for MULTI USER mode Enter NEW MASTER programming code 4 8 digits for all multi codes Enter up to 100 user codes for relay output 1 Code 4 8 digits User number 00 99 BIA e e Ll Code 4 8 digits Enter up to 10 user codes for relay output 2 User number 0 9 Programming Relay output modes Output 1 in momentary mode Can be 1 3 i digits 1 999 seconds 4 d L Output 2 in momentary mode Can be 1 3 digits 1 999 seconds 5 e Restore Defaults Output 1 in latching or toggle mode Output 2 in latching or toggle mode 1 Disconnect the power supply 2 Put the DAP jumper in the ON position 3 Re connect the power supply The buzzer will be activated 4 Put the DAP jumper back in the OFF position 5 The keypad is now in programming mode ready to receive data Additional k
3. password allows users not in caller ID list TE eE to call intercom and use pass code to activate relay 03 Change monitoring mode password dial to listen in mode Delete a button calling number where n number 1 2 or 3 N A gt Optional Speaker volume Where level 0 4 3 input limit 3 222 005 i Connect shield of CAT5 to OV Connections SK model amp gt power supply switch 4 Microphone volume Where level 0 4 Advanced keypad To functions See additional exit puton 51 Relay time Where 1 9999 seconds 1 sec detail overleaf Output 5327 Max call time Where 005 999 seconds 3 digit code 60 sec 12 24y OUT1 OUT2 552 Max monitoring time for listen in mode when calling the intercom ac dc ie 00 60 mins 00 no limit 572 2H Unit can call or SMS service number by set duration to prevent S M card _ SIM card deactivation if seldom used 00 60 days 00 no inform 5 Register your SIM card with the network and check it works in a mobile 58 2 phone first If you are using a Pre pay or Pay amp Go SIM it will need topped Seice NUMDIL Moree eed P P intercom 6 Ensure the power is OFF before inserting the SIM card 7 Carefully slide the SIM holder in the OPEN direction insert the SIM 77 NIA use a screwdriver 65 answer the call amp wait for pass code 2 answer the call amp y i t ticall tivate 2 h 8 After a final
4. ringing the intercom may not work Q There is no audio from the gate but the person at the gate can hear ok A This can be due to low reception Check reception level by 20 Change SIM card if necessary to another network which may have better coverage Purchase a high gain antenna This may also be caused by either a defective microphone or incorrect microphone wiring or a short circuit by whiskers between the centre core and the shielding or excessive microphone cable length Q The audio quality that can be heard on the remote telephone is poor or humming buzzing A A small amount of GSM buzz can be considered normal on GSM intercoms but not so much that causes inability to hear the person speaking This can be caused by the GSM antenna being mounted too close to the speech panel or not mounted high enough Try earthling the speech panel chassis to OV of the power supply This is also a symptom of poor reception Try above steps on checking and improving reception Q The or key does not work when the intercom calls a phone A Check if you can hear the relay clicking at the gate when the or key is pressed during a call If it can be heard then the system is working check wiring between the relay and the lock or gate panel If the relays do not make a clicking sound then check this feature on a different mobile cell phone or landline If it works on a different phone check the settings on the phone in q
5. END SMS SEND SMS x22 21 Reply will indicate O dial out number opened or closed Dial in number for caller ID access 33 56 8 Option 1 If your number is saved inside the intercom Option 2 If your number is not saved in the intercom memory just dial it and it will activate the door or gate memory it will answer the call Enter the code on without answering your call The intercom will end the your telephone keypad to activate the door or gate call for you default code shown
6. GSM 3S amp SK V3 5 Installation Manual Programming Programming is best done by SMS text It can also be done by DTMF from a normal telephone 1 First check reception Send the following SMS to the unit 20 Installation 1 Before you install this equipment please read this full manual 2 Ensure that there is good network reception at the location where it will be installed 3 For medium or low reception areas Whore 2 wil be beween tanda1 SS MADD DNDDDI r io interferen n Il l i in install an optional external antenna Below 14 can cause problems with relay Td ot Ensure it is kept as high as possible operation or no voice from the gate to the 1 12 13 20 21 31 ae and ABOVE all electronics house Take action to improve reception Poor Medium Good 2 Program the numbers you wish the unit to dial when the call button is lenuanee pressed up to a maximum of 3 numbers Each SMS must start with the pass Pillar code default 1234 in the following format 12 1234 followed immediately Side View by a command E g to program the telephone number 0987654321 enter the following SMS a Wi ri ng ma to 3 numbers can be sent together in a single SMS as 12 1234 110987654321 ONS 4 Carefully follow the wiring instructions Additional wiring suggestions ee amare Grane for electric strike lock and magnetic lock are shown overleaf Pass code Data i2 Telephone number Function code 13 Telephone number 3 O
7. check of wiring switch on the power a 13 Delete phone number for caller ID access 9 Allow 20 30 seconds for the unit to boot up and detect the network Once successful connection has been made the unit will sound a 73 confirmation tone and the status LED will begin flashing If there is a fault or problem the unit will emit a series of bleeps or warning 999 tones If this occurs check Check stored numbers Note no pass code needed for this 1 That the SIM card has been activated and has credit command O dial out number Dial in number 2 That the SIM card does not require a PIN code disable this in a phone 3 That the SIM card can make and received a call on a phone eee Remember m agit ay see a NOP a ote rogramming is done by calling the unit amp entering the pass code first then after a 4 If the SIM card was purchased with a phone that it is not locked to that long single confirm tone commands can be entered A fault is indicated by 3 short bleeps phone Call the network operator to check 5 Switch off power remove and reseat the SIM card and try again Keypad Programming only SK models The amber LED indicates standby mode flashing or programming mode ON Green LED indicates output 1 active Red LED indicates output 2 active Enter Programming mode ellei Lo loys Choosing single user mode or multi user The unit is now in programming mode Amber LED will remain ON 0000
8. eypad information EG IN EGRESS INPUT A Normally Open N O input terminal refers to ground with the help of a normally open button to activate the Output 1 for the same time period as the user code Egress button is usually put inside the house near the door More than one egress buttons can be connected in parallel to the terminal Leave this terminal open if it is not used KEY ACT KEYPAD ACTIVE OUTPUT An NPN transistor open collector output It switches to ground for 10 seconds on each key touching This can be used to turn on lights CCTV camera or buzzer to notify a guard The rating of this output is lc max 100mA sink Vc max 24VDC DU OUT DURESS OUTPUT An NPN transistor open collector output It switches to ground after the Duress Code is entered Use it to trigger an alarm zone or turn on a buzzer to notify a guard Ic max 100mA sink Vc max 24VDC Fault finding amp FAQs Q The unit will not power up No LEDs on A Check power supply voltage is within 11 5V 12 5V DC Q The unit powers up but there is a bleeping from the door station A This means the unit is not able to detect the network for some reason Check the SIM card is activated and has calling credit Power off the unit remove the SIM and check it in a mobile phone to verify it can make a call Check the SIM does not ask for a PIN code when put in a phone If it does then disable the PIN code request Check the SIM is a standard
9. ptional Antenna Elevated position 3 It is recommended to change the no answer time if there is more than 1 number stored This stops the unit ringing a number after a set time and can be used to prevent voicemail answering the call Send the following SMS 42 1234 52 Where can be 2 digits from 10 99 seconds default is 20 Speech panel Intercom The unit can allow up to 100 telephone numbers to be stored for users to be able to ring the system for automatic entry This uses caller ID like a Shielded CATS5 cable GSM 3E phone to determine the identity of the caller First the unit must know what country it is operating in 4 Program the country code as follows 4 ox 99 Where can be 1 3 digits For uk insert 44 for Ireland 353 Do not TAN 234871224 use any leading zeros Transmitter GSM LED nnnm JL 5 Enter the telephone numbers required to have access control Do not enter searching country code just the complete number as you would dial it Power LED Up to 3 numbers can be sent together in the same SMS Just 12 1234 720987654321 add 72 then the number then each time The pass code only needs to be put at the beginning of each new messge Mm re Network found CPU LED nnnm Standby a Busy E Additional Programming Parameters Code Description Default Call 9999 Button Hl 01 2 Change programming password 292274 Change access control
10. uestion under DTMF tones Failure of DTMF tones to operate correctly is also a symptom of low reception Check steps above on improving reception Try pressing the buttons longer when attempting to activate the gates or door User Manual For GSM 38E S amp GSM 3E SK Wireless Intercom This GSM intercom system will call up to 3 telephone numbers in sequence when the call button is pressed There are several modes of operation depending on how the unit has been programmed by your installer The following instructions will assume default programming Intercom calling your phone My Gate Call button CALLING pressed ANSWER DECLINE J Answer call sending SMS Commands Press to open OR Press to hold open and Press 1 to release again Only some gate systems allow hold open control depending on manufacturer Default pass code 5678 is shown in all examples This may have been changed by your installer Trigger Gate Latch or hold Unlatch Door open gate door gate door SEND SMS SEND SMS SEND SMS 33 56 8 34 56 8 35 56 8 aa 3 Leaf i 2 3 HOLD OPEN FEATURE OR PARTY MODE Some gate systems allow hold open control depending on manufacturer Send the following SMS commands to control the gates Calling the intercom options Dialling MY GATE nN s END If limit switch fitted Check stored check gate status numbers S
Download Pdf Manuals
Related Search