Home

Telstra Slim Digital Cordless Phone

1. Help Y Icon flashes e Is the handset registered correctly to the base See page 53 e Check that the mains power is correctly connected e Check that the handset is within range of the base e Is the battery low Place the handset on the base charger to recharge dmm LI Battery icon does appear to be filling e Try cleaning the charging contacts e Check that the mains power is correctly connected You hear the busy tone when you press e Make sure the handset is in range of the base e Another handset registered to your Telstra Slim base may be on the line 56 Answering machine does not record any messages e The memory may be full Play and delete old messages See page 45 Answering machine messages have the wrong date and time e Have you manually set the date and time See page 13 Cannot access your messages from another phone e Have you changed the remote access security PIN code See page 46 Always keep a note of the new PIN code in a safe place e Has remote access been disabled To enable remote access See page 46 Help No Calling Number Display number name displayed e Have you subscribed to Telstra Calling Number Display See page 35 e The caller may have blocked their number e An exact name number match was not found in your phonebook Check that you have stored the complete number including drea code Base unit does not ring but the lights are on e Have you co
2. Telstra Slim Digital cordless phone Digital cordless phone with integrated answering machine User Guide This telephone has been designed for ease of use Please read the instructions and keep it handy for future reference If you have any problems with your phone refer to the Help section of this User Guide 1300 369 193 Introduction To your Telstra Slim Digital Cordless Telephone Telstra Slim Digital Cordless Telephone with Answering Machine e Ultra slim handset e Phonebook lets you store up to 200 contact numbers for easy dialling e Store a phonebook entry then copy it or the entire phonebook to another Telstra Slim handset e Send and receive text messages e Quick access to a range of Telstra Network Services including Call Waiting and Call Forward e Telstra Calling Number Display lets you see who s calling Your phone stores details of the last 20 callers in a Calls list e Answering machine with up to 15 minutes digital recording time and helpful voice prompts Telstra Slim answering machine version only Call features and charges may apply IMPORTANT You need to subscribe to Telstra s Calling Number Display service to be able to see the caller s number or name when called or in the Missed and Received Calls logs See page 35 for more details IMPORTANT This equipment requires electricity to work You will not be able to make any telephone calls when the
3. Choose Back to return to the previous menu level or press GJ to return to standby mode If you have more than one Service Centre stored on your Telstra Slim you will need to select which one you want to use for sending see next section 51 Text messaging Select Send Service Centre Only service centres that have numbers stored will be displayed as Send Centres 1 Choose Menu TET is displayed Choose OK 2 Press amor EJ to select TEXT SETTINGS and choose OK 3 Press XJ to select SEHD SERVICE and choose OK 4 Press aaj or XJ to select the Service Centre and choose OK 5 Choose Back to return to the previous menu level Or press Gad to return to standby mode 52 Message alert When you receive a text message e the new message beep will sound at the handset e the new text message icon is shown on the handset display e the base indicator light flashes These alerts can be switched On or Off The default setting is On Switch new message alert on or off 1 Choose Menu TET is displayed Choose OK 2 Press emorEY to select TEXT SETTINGS and choose OK 3 Press to select HEH TEXT ALERT and choose OK 4 Press aaj or XJ to select OH or OFF and choose OK Choose Back to return to the previous menu level VI Additional handsets multi handset packs only If you have purchased a multi handset pack you are able to make internal calls transfer external calls from one handset to
4. Press E to insert a space Use ES and or KJ for other punctuation characters You must enter a name to go with a number To enter a pause in a phonebook number When storing a number press and hold KJ and a P will be displayed Phonebook empty If the phonebook is empty and you press the display shows the phonebook option HEH EHTE Once an entry has been stored the full menu is displayed Phonebook To view a name and number in the phonebook 1 Press A in standby mode The first entry in the phonebook will be displayed 2 Press Kemi Or EY to select the entry you want 3 Choose Option and scroll to IEH 4 Choose OK Press Kar EJ to view the name number and group of the selected entry 5 Choose Back to return to the previous level To check how many phonebook entries are stored 1 From standby mode press a The phonebook will be displayed 2 Choose Option Press XJ to select CAPACITY and choose OK The number of available spaces for entries in the phonebook will be displayed e g 150 200 3 Choose Back to return to the previous menu level To dial an entry from the phonebook 1 In standby mode press E The first entry in the phonebook will be displayed 2 Press Mor EJ to select the entry you want or search alphabetically using the alphanumeric keypad see tip below 3 Choose F to dial the desired number To search alphabetically Press the relevant keypad button e g for the entries
5. beginning with T press EM once then press GaorE to scroll through the entries Call groups You can assign different ringtones to different call groups see page 27 Your call group options are General Family Business Friends Utilities VIP Others No Group To edit aname and or number in the phonebook 1 Press iia in standby mode 2 Press amor EJ to select the entry you want 3 crape ua and press XJ to scroll to s and choose OK 4 Use the wieunad to enter a new name 5 Press to select HUMBER to enter a new number 6 Press EJ to select GROU group 7 Choose OK to save or Back to return to the previous menu level F to select a different When editing a name or number choose Clear to delete characters and digits 25 Phonebook Copy all phonebook entries from one handset to another 1 Press A in standby mode 2 The first entry in the phonebook will be displayed 3 Choose Option and press XJ select COFY ALL and choose OK 4 Press aa or a to select the handset you want to copy to and choose OK Note if you only have one additional handset the additional handset will be selected automatically At the receiving handset 5 Display will show RECEIVE DIF ENTRIES Choose Yes to apie or No to cancel 6 If the transfer is successful the display will show COPIED 7 Choose Back to return to the previous menu level You can copy the entire phonebook to another handset registered to the
6. replaces the oldest Your Telstra Slim can store up to a total of 20 text messages in the Inbox and Outbox combined Using the Outbox Saved draft text messages and messages you have sent are kept in the Outbox If a text message you tried to send was not successful it is stored in the Outbox and shown as FAIL 1 Choose Menu TEST is bd Choose OK 2 Press EJ to select OLUTEOX Choose OK 3 The number of messages is displayed e g 4 Press fam or EJ to select the message you want and choose Edit Templates There are five pre set templates Please call Pll be there at Thank you Pll call you Happy Birthday Receiving a call while writing a text If you are writing a text and you receive a call the text will be lost 49 Text messaging Text messaging Do you have two SMS enabled phone bases connected to the same phone line If you have two SMS enabled phones plugged into one line you are likely to experience problems receiving text messages Normally only one SMS enabled base unit DECT or cordless can be plugged into any line If you do want to use two base units and still receive written text on one phone you must delete receive service centre number from one of the phones To do this on your Telstra Slim see instructions on page 51 This will allow you to send text messages via either base station but text messages will only be received on the product with the active receive centre number If the bas
7. to advise your caller that they will not be able to leave a message Your own Answer Only message can be up to 1 minute long and will replace the pre recorded message To reinstate the pre recorded messages delete your own recorded outgoing message see opposite Answer settings 1 Choose Menu Press J to select ANSHEF HACHIHE Choose OK 2 Press EJ to select 4HS SETTINGS and choose OK 3 Press aa or Ba to select the outgoing message type ANSWER OHLY or AHS amp REI 4 Press EJ to select ANSHER DELAY Press aaj or Ka to select thes setting 5 Press to select FECORDIHG TIME Press aaj or 4 to select the ae message length 30 60 120 or 180 seconds 6 Press to select CALL SCREENING Press G or E to select On or Off 7 Choose OK to save 8 Choose Back to return to the previous menu level 43 Answering machine You cannot delete a pre recorded message If you delete your personal outgoing message the pre recorded outgoing message will be automatically reinstated as your outgoing message Answer mode Choose which outgoing message you want played to callers Answer delay Answer delay sets the number of times your Telstra Slim will ring before the answering machine answers up your call and starts playing the outgoing message You can change the Answer Delay setting to between 2 4 6 8 rings or Time Saver Time Saver When you ring in to access your messages remotely if your answering machine
8. 33 051 775 556 Trade Mark of Telstra Corporation Limited Registered Trade Mark of Telstra Corporation Limited
9. Additional handsets multi handset packs only 53 Call another handset 53 Transfer a call 53 3 Way conference call 53 Registering an additional handset 53 Select base 54 De register a handset 54 7 Important safety instructions When using your telephone equipment basic safety precautions should always be followed to reduce the risk of fire electric shock and injury including the following 1 Read and understand all the instructions 2 Follow all warnings and instructions marked on the product 3 Unplug this product from the wall outlet before cleaning Do not use liquid or aerosol cleaners Use a damp cloth for cleaning 4 Do not use this product near water for example near a bath tub kitchen sink swimming pool 5 Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock 6 Unplug this product from the wall outlet and contact TecHelp on 1300 369 193 under the following conditions e When the power supply cord or plug is damaged or frayed e If the product does not operate normally by following the operating instructions e If the product has been dropped and the outer casing has been damaged e If the product exhibits a distinct change in performance 7 Avoid using a telephone during an electrical storm There may be a remote risk of electric shock from lightning 8 Do not use the telephone to report a gas leak in the vicinity of the le
10. Choose ES to confirm or HO to cancel If you restore your handset to its original factory settings this will not affect e The phonebook e Text messages stored in the Inbox or Outbox e The Calls list Settings Sounds Handset ringer 1 Choose Menu press EY to select S0UHI and choose OK RINGER is highlighted Choose OK 3 The current external melody is highlighted Press aaj or Ba to select the ringtone you want for external calls 4 Press EJ to select IH E or a to select che ageden you want for internal calls 5 Press EJ to select RING VOLUME Press G or to select from the volume levels 1 5 or off to mute the ringer volume 6 When the ringer volume is set to off a single beep will be heard when the phone rings To turn the single beep off press KB to select SILEHT Press aaj or fk to select BEEF or OFF 7 Choose OK to confirm 8 Choose Back to return to the previous menu level You can set different ringtones for external calls and internal calls Choose from 10 polyphonic and 5 standard handset ringtones The handset also has 5 ringer volume settings plus Off You can also switch the handset ringer off by pressing and holding ad You can still hear a single beep when you receive an incoming call by changing the SILENT setting from UFF to BEEF Handset beeps 1 Choose Menu press EY to select SOUND and choose OK 2 Press EJ to select TOHES Choose OK 3 KEY BEEPS option is ica
11. OK Scroll to the entry or number you want and choose OK Choose OK again to send STORE Choose OK to save the message in the Outbox for sending later are displayed Press fmor EJ to highlight the template you want then choose OK to insert the template into your text Choose OK The template options Text messaging 4 When aie a message the es shows 5 5 Press a to cancel at any time and return to standby mode Jo lets text is not sent the display shows MESSAGE FRILET The failed message will then be cated in the Outbox Writing tips Use the keypad to enter letters and numbers eg to write today 2day Press E four times to enter 2 Press E once to enter d Press E once to enter a Press Eda three times to enter y Press E to enter a space and use ES and or KJ for other characters Choose Clear to delete incorrect characters Press aaj or fa to move the cursor to the point you want Press Mor J to move the cursor to the beginning or end of the text Upper amp lower case Press E to change between upper ABC lower abc and sentence Abc case letters Maximum number of characters in a text message is 160 The display shows a character countdown from 160 down to 0 amp message then MESSAGE SENT Sent and saved texts are stored in the Outbox Your Telstra Slim s outbox is like a redial list It holds copies of sent and saved messages When the Outbox is full a new message
12. Press aaj or XJ to select OH or OFF 4 Press EJ to select COHFIF Press aaj or Xa to m t OM or OFF 5 Press X2 to select BATTERY i Press aaj or Xa to select OH or OFF 6 Press EJ to select OUT OF RANGE Press aaj or Xa to select OH or OFF 7 Choose OK to confirm 8 Choose Back to return to the previous menu level Your handset can give a beep to confirm a successful action such as storing a new phonebook entry It can give warning beeps when you are going out of range and when the battery is low It can also beep every time you press a button You can switch these tones on or off individually as set out above 31 Settings Settings Base settings Ringer 1 Choose Menu press fami to select SETTINGS 2 Press EJ to select BASE SETTING Choose OK and choose OK 3 RINGER is HIKE Choose OK 4 The RINGTOHE option is highlighted Press orf to select the desired ringtone Press J to select FING VOLUME Press aaj or A to select thie volume or SILEHT to mute the ringer volume 6 Choose OK to save 7 Choose Back to return to the previous menu Choose from 5 base ringtones There are 6 volume levels including SILENT Handset priority 1 Choose Menu press fam to select SETTINGS and choose OK 2 Press EJ to select BASE SETTING Choose OK 3 Press EJ to select HiSET PRIORITY Choose OK 4 ALL HAHDSETS is highlighted Choose OK fdr all handsets t to aring a or press t
13. a mains power surge To obtain service during the term of this warranty call the TecHelp Information Line on 1300 369 193 or contact us by e mail at tcpsupport ingrammicro com au If it is necessary to have the product serviced the Customer Service Representative will inform you of the product return process Please ensure that a You provide proof of purchase b Your product is suitably packaged and c You have included all components from the original purchase Subject to your Statutory Rights a Any claim under this warranty is limited to the cost of repair or replacement of the product and b If the goods are found to be in sound Customer service amp Product warranty working order by the authorised service centre you may be charged a fee for service and for any other direct costs associated with having the product delivered for service For your records Date of purchase For guarantee purposes proof of purchase is required so please keep your receipt 61 www telstra com COPYRIGHT 2008 Telstra Corporation Limited This work is copyright All rights reserved Other than for purposes and subject to conditions prescribed under the Copyright Act no part of it may in any form or by any means electronic mechanical photo copying microcopuying scanning recording or otherwise be reproduced stored in a retrieval system or transmitted without prior permission from Telstra Corporation Limited ABN
14. and gives a short cut to access e Missed calls e Answering machine messages e Text messages 1 Press A The Inbox screen is displayed 2 Press Aor EJ to select the option you want and choose OK Paging calls cannot be answered by a handset 23 Phonebook You can store up to 200 names and numbers in the phonebook Names can be up to 15 characters long and numbers up to 24 digits To store a name and number To access the phonebook from standby mode press 1 When the phonebook is empty the phonebook menu is displayed 2 When storing the first entry HEH EHTRY is highlighted Choose OK to enter a new name and number When storing further entries The phonebook list is displayed with the first entry highlighted Choose Option HEH ENTE is highlighted Choose OK to enter a new name and number 3 Enter the desired name 4 Press RZ to select HUMEER and enter the desired enen somber 5 If required scroll to SELECT GROUP Press ma or Bj to set ihe group i want Choose OK Display shows SA EL 24 6 Choose Back to return to the previous menu level Entering names Use the keypad letters to enter names e g to store Tom Press K once to enter T Press Ka three times to enter o Press Kea once to enter m Writing tips Press Clear to delete the last character or digit Press iJ or Rd to move backwards or forwards through character digits Press EJ to switch between upper lower or sentence case
15. another and use the conference option Call another handset You can make internal calls between two handsets 1 Choose Int and if you have only one other handset it will ring If you have extra handsets press aaj or to select the handset 1 5 you want to call then choose OK Transfer a call You can transfer an external call to another handset registered to the base 1 During your call choose Int Your external caller is put on hold 2 If you have one only other handset it will ring If you have extra handsets press E or BQ to select the handset 1 5 you want then choose OK 3 When the other handset answers you can announce the caller 4 Choose Switch to switch between the two callers 3 Way conference call You can hold a 3 way conference call between 2 internal callers and 1 external caller 1 During your call choose Int Your external caller is put on hold 2 If you have only one other handset it will ring If you have extra handsets press Eor to select the handset 1 5 you want then choose OK 3 When the other handset answers you can announce the call Choose Conf to join all callers If the other handset does not answer choose SIMISLE to return to your original caller Registering an additional handset Your additional handset s will come pre registered but should you need to register a handset follow these steps At the handset 1 Choose Menu press to select SETTIHGS and choo
16. base If the phonebook becomes full during copying the display shows MEMORY FULL If copying is not successful the display shows DRE CORY FAILED If you copy an entry that already exists in the receiving receiving handset it will create a duplicate entry 26 To copy one phonebook entry from one handset to another 1 Press A in standby mode then press 0 or EJ to select the entry you want to copy 2 Press Option and press KZ to select COPY and press OK 3 Press aaj or BJ to select the handset you want to copy to and press OK Note if you only have one additional handset the additional handset will be selected automatically At the receiving handset 5 Display will show RECEIVE DIF ENTRIES Choose Yes to ne or No to amal 6 If the transfer is successful the display will show COFIET 7 Choose Back to return to the previous menu level You can copy an entry to another handset registered to the base If you copy an entry that already exists in the receiving handset it will create a duplicate entry Phonebook To delete one entry from the phonebook 1 Press ial 2 Press fem or J to select the entry you want to delete 3 Choose Option press XJ to select HELETE EHTE and choose OK 4 Choose Yes to confirm or No to cancel 5 Choose Back to return to the previous menu level To delete all entries in the phonebook 1 Press MA in standby mode 2 Choose Option press Mor EY to select DELE
17. easy to use menu system Each menu has a list of options as outlined on the following page When the handset is switched on and in standbu 1 Choose Menu to open the main menu 2 Then press Kemi or EJ buttons to move through the available options 3 Choose the OK option button to select a menu option or the Back button to return to the previous screen To exit a menu and return to standby press 18 Option buttons Press to select the option shown on the screen If no buttons are pressed for 30 seconds the handset returns to standby automatically g elstra Getting to know your phone Menu layout Text Write new text Inbox Outbox Template Text settings v Yv pR Answer Machine Sound Settings Play messages Ringer H S settings Delete msg Tones Base settings Answer on off Date Time Alarm Outgoing msg Ans settings Ex amp Callslistempty Calls list display Telstra menu Names menu Phonebook press Option Phonebook empty Settings e Feature displayed press Details Assistant Option New entry Delete eCall Wait On Capacity Delete all eCall Wait Off New entry Call number eCheck Call Wait Edit entry Store number eCall Return View Settings eCheck CF Copy Immed Copy all eCheckCFBusy Delete entry eCheck CF Delete all No Ans Capacity eCall Back Off Edit call grp eTecHelp Speed dial Redial Redial list displayed press Option Delete Delete all Call number Store number 19
18. is set to Time Saver and you have new messages it will answer after 10 seconds If you do not have any new messages it will answer after 20 seconds This means you can hang up knowing you have no new messages saving you time and the cost of the call Recording time Set the maximum message length 60 120 or 180 seconds or unlimited Call screening When the answering machine is on and answers a call you can listen to the caller leaving a message You can then identify the caller and decide whether to take the call in person The call can be heard through the base speaker or the handset as follows 44 1 When your Telstra Slim rings wait for the answering machine to answer the call When the caller begins leaving a message the display shows SCEEEHIHG Choose Yes to hear the caller Press fam to stop screening without talking to the caller 2 To interrupt and speak to the caller directly press F While screening you can adjust the volume by pressing or Mor EJ Message playback 1 NOORE Menu Press X2 to select AHSHER IHE Choose OK MESSAGES is highlighted Choose OK 3 The handset displays the number or name of the caller if available and the date and time it was received During playback you have the following options 1 Press El to hear the message over the handset loudspeaker 2 Press to play back through the earpiece again Press Mor EJ to adjust the volume 3 Press once to repeat the mess
19. more than one base you can select which base to use If you have a handset registered to more than one base and then deregister it from one of them you will need to re select which base to use Until the base is selected the handset will display KES ii Help Phone does not work e Have you installed the battery correctly See page 10 You have a dial tone but the phone will not dial out e If you are connected to a PABX check e Check that the mains power is correctly whether you need to dial an access code connected e Is the handset switched off To switch the handset on see page 20 Handset does not ring e The ringer volume may be switched off See page 31 e Check that the mains power is correctly connected No dial tone e Is the telephone cord of the base plugged into the phone socket e Make sure the handset is registered to the e Check that the mains power is switched on base See page 53 at the power point No display e Only use the telephone cord supplied with e The battery may be flat dead or incorrectly the phone inserted Cannot dial out or receive calls e Recharge or replace the battery e Check that the mains power is correctly connected e The battery may need recharging e Has there been a power cut If so place the handset back on the base for 10 seconds and try again If it still does not work disconnect the battery and mains power for 10 minutes then reconnect and try again 55
20. power fails Alternative arrangements should be made to access emergency services in times of power failure As a Digitally Enhanced Cordless Telecommunications DECT product your Telstra Slim provides e Digital clarity e Digital range e Digital security This product has been designed and tested for Australian conditions for use with Telstra s network This User Guide provides you with all the information you need to get the most from your phone Before you make your first call you will need to set up your phone Follow the simple instructions on the next few pages Some Telstra services such as SMS Message Bank and Calling Number Display may attract feature and usage charges Please visit Telstra com for details Need help SHOULD YOU EXPERIENCE ANY OPERATIONAL DIFFICULTIES WITH YOUR TELSTRA PRODUCT PLEASE CONTACT THE TECHELP INFORMATION LINE 1300 369 193 OR CONTACT US BY E MAIL AT tcpsupport ingrammicro com au You may also find assistance in the Help section at the end of this user guide Hearing aid Please note that the Telstra Slim works by sending radio signals between the base and handset These signals may interfere with some hearing aids causing a humming noise Got everything The package contains the following items e Telstra Slim handset e Telstra Slim base unit or Telstra Slim answering machine base unit Telstra Slim answering machine version only e AC power adaptor
21. stop playback Press adjust the speaker volume up or down during playback At the end of playback press and follow the voice prompts Press again to delete all old messages Answering machine messages that are not deleted are automatically saved Memory full If the caller is still talking when the memory becomes full the caller hears Thank you for calling and the machine will hang up You must delete messages before your machine will be able to record new ones To delete old played messages see page 45 or opposite for instructions 45 Answering machine Remote access You can operate your answering machine from any Touchtone phone by calling your Telstra Slim and entering a 4 digit security code To enable disable remote access 1 Choose Menu Press to select AHSHER MACHINE Choose OK 2 Press mor to select REMOTE ACCESS and choose OK 3 Press mal or Xa to select DISABLE or EHABLE 4 If you select EHAELE the display asks you to enter the Remote Access PIN Enter the current 4 digit PIN The default setting is BEEBE Choose OK 5 Enter a new PIN Choose OK Enter the PIN again and choose OK to save Remote access When enabled you can call in from another phone to listen to your messages and operate your answering machine You are asked to set a Remote Access PIN so that other people cannot ring up and listen to your messages 46 If you forget to switch on your answering machine 1 C
22. REN is less than 3 59 Customer service amp Product warranty IMPORTANT Please retain this booklet with your sales receipt as proof of the date of purchase Customer Service If you require assistance in operating this product please call the TecHelp Information Line on 1300 369 193 or contact us by e mail at tcpsupport ingrammicro com au If you are trying to access a Telstra Network Service and require assistance specifically related to the network service or would like to subscribe to the service contact Telstra on 132200 for residential customers or 132000 for business customers Product Warranty Subject to the conditions below Telstra guarantees this product against any defect in materials or workmanship under conditions of normal use for a period of 24 months from date of purchase The benefits conferred by this warranty are in addition to other warranties and remedies that are implied under the Trade Practices Act and similar State and Territory laws Statutory Rights Subject to your Statutory Rights the goods will not be eligible for service under this warranty if a Proof of purchase cannot be provided 60 b The defect was caused by an accident misuse abuse improper installation or operation vermin infestation lack of reasonable care unauthorised modification loss of parts tampering or attempted repair by a person not authorised by Telstra or c The product has been damaged by lightning or
23. TE ALL and choose OK 3 Choose Yes to confirm or No to cancel 4 Choose Back to return to the previous menu level To edit call group name Note You can choose your own name for a call group 1 Press MA in standby mode 2 Choose Pa press Mor EJ to select ENIT CALL GEF and choose OK 3 Choose fx Ack to select the call group you want to edit 4 Press OK The display highlights REMAMNE SROUF Choose OK 5 Choose Clear to delete the current name and enter a new name 6 Choose OK to save 7 Choose Back to return to the previous menu level To change call group ringtone Note You can assign different ring melodies to callers from different Call Groups 1 Press iil in standby mode 2 Choose Option press Aor EY to select EIT CALL GREF and choose OK 3 Choose Mor EY to select the call group you want to edit 4 Choose OK Then press to select RIMSTOHE Choose OK 5 Press aaj or Bj to choose the ringtone A sample of each one is played when highlighted 6 Choose OK to save 7 Choose Back to return to the previous menu level 27 Phonebook Speed dial Note Up to 9 of the phonebook entries can also be allocated as Speed Dial entries You can allocate a name and number from the phonebook to each of the number buttons except 1 To copy a phonebook entry to Speed dial 1 Press A in standby mode 2 Choose despa press fami or KY to select SPEED MAL and choose OK 3 Choose ft Qo to s
24. Using the phone Switch handset on or off To switch the handset off 1 Press and hold Kd 2 SKHITCH OFF to confirm will be displayed Choose Yes To switch the handset on 1 Press and hold G Make an external call 1 Press to access the line 2 When you hear the dial tone dial the number Pre dialling 1 Enter the number If you make a mistake press Clear to delete the last digit 2 Press to dial End a call 1 Press d When you make a call the charge light on the standard Telstra Slim base is extinguished On a Telstra Slim Answering Machine base the 4g In Use light flashes 20 Call timer Your handset will automatically time the duration of all external calls The handset display shows the call duration both during and for a few seconds after your call is terminated Out of range warning When the handset goes out of range of the base the antenna icon flashes If you are on a call the line will hang up When you move back within in range the handset will automatically re connect to the base Receive a call When you receive a call the phone rings The display will show the caller s number if available or the caller s name if it matches an entry in the phonebook If you do not subscribe to Telstra sees nubs Display the screen shows Es TERHAL CALL 1 Press F to answer the incoming call Auto answer As long as you have auto answer set to ON you can answer a call by lifting t
25. age or twice to play the previous message Answering machine 4 Press to play the next message 5 Press iy Or to delete the current message The display shows DELETED 6 Press Pause or to pause playback 7 Press fd to cancel playback and return to standby mode At the end of playback the handset will return to standby mode The messages are renumbered to take account of any deleted messages Each message is played back with the day and time of the call announced as well as the caller s number if available and name if stored in the phonebook If there are no messages the display shows Hi p a i et Me Ss oAisk ama Benen aus EE New unplayed messages cannot be deleted Delete all old messages 1 Choose Menu Press EY to select AHSHER MACHINE Choose OK 2 Press EJ to select DELETE MSG and choose OK If there are no old unplayed messages the display shows H OLI MESSAGES If there are old messages the display shows LETE ALL Choose ES to confirm or HO to 3 Choose Back to return to the previous menu level Using the answering machine at the base Switch on off 1 Press Gi The setting is announced Message playback 1 Press WE New messages are played first During playback Press to delete the current message Press EJ once to repeat the message Press H twice to play the previous message Press A to play the next message Press W to pause and resume playback Press d to
26. ak 9 Use only the supplied NiMH Nickel Metal Hydride battery The operation periods for the handsets are only applicable with the default battery capacity 10 The use of other battery types or non rechargeable battery primary cell can be dangerous These may Important safety instructions cause interference and or unit damage Telstra will not be held liable for damage arising from such noncompliance 11 Use only the AC power adaptors supplied with this product Please contact TecHelp on 1300 369 193 for replacement adaptors 12 Please ensure that the polarity plug is inserted correctly 13 Do not immerse the battery in water and do not place it in a fire Getting started Location Place your Telstra Slim within 2 metres of the mains power socket and telephone socket so that the cables will reach Make sure it is at least 1 metre away from other electrical appliances to avoid interference Your Telstra Slim works by sending radio signals between the handset and base The strength of the signal depends on where you locate the base Putting it as high as possible ensures the best signal Setting up 1 Plug the mains power cable into the socket marked me on the underside of the base plug the other end into the mains power wall socket and switch the power on You can place the cable behind the retaining clip to prevent the plug being accidentally pulled from the socket The base indicator will light up and th
27. all Listen for the number of your last missed call To check Call Forward Immediate 1 Press Telstra 2 Press to select CHECKE CF IM Choose OK 3 Press to call Listen for confirmation status of your instructions To check Call Forward on Busy 1 Press BBQ 2 Press EJ to select CHECK CF EBUSY Choose OK 3 Press to call Listen for confirmation status of your instructions To check Call Forward on No Answer 1 Press 2 Press to select CHECK CF HO ANS OK 3 Press to call Listen for confirmation status of your instructions Choose To turn Call Back off If you have activated the Call Back feature using D ED after you hear busy tone you can turn the feature off as follows 1 Press R 2 Press EJ to select CALL BACK OK 3 Press to call 4 Press K to finish OFF Choose To call the TecHelp Helpdesk 1 Press 2 Press J to select HELFIESK Press KA to call 39 Answering machine Telstra Slim answering machine version only Answering machine base 1 2 position handset charging contacts The handset can be placed flat on the base or can sit in an upright position 2 Delete Press to delete answering machine messages 3 Answer On Off Press to switch answering machine on or off 4 SKIP lt While listening to your messages press once to repeat the current message twice to play the previous message 5 6 Vol Vol Press to increase or decrease speaker volume during play
28. all your number from another phone and let it ring After 20 rings the machine will switch on and answer your call 2 Enter your Remote Access PIN Play back your messages as shown below in Operating your answering machine remotely If you do not choose to switch your answering machine On it will switch off when the call is ended IMPORTANT You should change the security PIN from the original setting of HEE It is advisable to make a note of your new PIN code and keep it somewhere safe Answering machine Operating your answering machine remotely 1 Dial your phone number When you hear your outgoing message press Hl You will hear Please enter your security code 2 Enter your 4 digit Remote Access PIN You will hear You have X new messages If you only have old messages you will hear You have X messages followed by To hear main menu press 1 When you have remotely accessed your Telstra Slim you can use the keypad to operate your answering machine Follow the announcements and instructions you hear Press to play main menu Press to play all messages Press to play new messages only Press to skip back to previous message Press to delete current message Press to skip forward to next message Press to set answer mode this lets you select the outgoing message to Answer amp Record or Answer Only Press to play outgoing message Press to set answering machine to On or Of
29. an set the date and time manually 9 Choose Back until you return to standby 2 The NiMH battery is already fitted in the handset Remove the battery compartment cover by sliding it downward and lifting off Locate the battery lead and connector and plug it into the socket inside the battery 12 13 Getting to know your phone gelstra a an N Telstra sA n m ZA 7 f a O E gt we A 4 Hi gK 6 no 14 Handset buttons 1 Telstra Press to open a list of Telstra network features 2 EM UP Redial In standby mode press to open and move through the Redial list When on a call press to adjust volume In menu mode press to scroll up through the options displayed on screen 3 Option button left Press to select options displayed on the screen above the left option button see diagram on page 18 In standby mode press to initiate an internal call 4 LEFT Phonebook In standby mode press to access the phonebook When on a call press to mute the handset When listening to answering machine messages press to play the previous message 5 Handsfree When on a call press to switch handsfree speakerphone on and off 6 Talk In standby mode press to make and receive calls Getting to know your phone 7 Star Press and hold to switch the handset ringer on or off 8 Option button right Press to select options displayed o
30. andset display provided it is not blocked prior to answering the call If your caller s name is stored in the phonebook and a number match is found you will see the caller s name on the display instead Call features and charges may apply Calls list When Telstra Calling Number Display is active on your service dialled numbers will be saved in the telephone s Calls list The Calls list holds up to 20 numbers The date and time of the call is also stored if available When the list is full and a new call is received the oldest entry will be deleted automatically The Calls list can hold numbers up to 20 digits and names up to 16 characters IMPORTANT To use Telstra Calling Number Display you must first subscribe to the service from Telstra For more information on Telstra Network Features call Telstra on 13 22 00 To ensure the caller s name is displayed make sure you have stored the full telephone number including the area code in the phonebook When anew call is received in the Calls list the El icon is displayed on the handset screen re omer is not available to the network UNAVAILABLE is displayed If ia ames has been blocked by the caller MITHHELT is displayed If the call is from a payphone PAYPHOHE is displayed If you do not subscribe to Telstra Calling Number peat any external call is displayed as ESTERHAL CALL When there are no calls in the Calls list the display shows E FTY and wil
31. back 7 Stop Press to stop play back 8 SKIP gt Press to skip forward to the next message 9 Play Press to play messages 10 Page Press to press to ring all registered handsets This is helpful for finding a missing handset see page 23 Also used during the registration process see page 53 40 11 Answering machine display Indicates answering machine is off 43 Indicates answering machine is on and the number of messages stored Flashes when you have new unplayed messages FA Displayed while a handset is accessing the machine FE Displayed while recording a message 12 Power light On Indicates power is on 12 In Use light Flashes when the handset has answered a call or is making a call 12 Text message SMS light On you have new text messages Flashing a text message is being sent Off all text messages have been read Answering machine ee0ee 080020808008080 eee oe Ban Pa Powers e2 e fos i ower s eee 1 RO sms y Lh gt annat y mE O o a o n n aa AA elstra o s Li I ace g I J 1 i g 41 Answering machine Your Telstra Slim can digitally record up to 59 individual messages within the maximum recording time of approximately 15 minutes You can operate your answering machine from e the handset e the base e remotely from any other Touchtone telephone see page 46 Your Telstra Slim com
32. e answering machine will be switched on 10 Slim Answering Machine Base i adaptor cable 2 The NiMH battery is already fitted in the handset Remove the battery compartment cover by sliding it downward and lifting off Locate the battery lead and connector and plug it into the socket inside the battery compartment the red wire should be on the left Tuck the battery leads in the space above the battery and slide the battery compartment cover back on until it clicks into place Ww Place the handset on the base to charge for at least 20 hours When the handset is fully charged the L icon will be displayed Getting started 4 When the battery is fully charged plug one end of the telephone line cord into the socket marked J L on the rear of the base and the other end into the telephone wall socket WARNING Do not place your Telstra Slim in the bathroom or other humid areas IMPORTANT The base station must be plugged into the mains power socket at all times Do not connect the telephone line until the handset is fully charged Only use the power and telephone cables supplied with the product Battery low warning If the L icon flashes in the handset display you will need to recharge the handse
33. e Telephone line cord e 1 NiMH rechargeable battery e 1 User manual If you have purchased a Telstra Slim multi handset pack you will also have the following for each additional handset e Telstra Slim handset e Telstra Slim charger e 1 NiMH rechargeable battery e AC power adaptor for the charger In this guide Important Safety Instructions 8 Using the phone 20 Switch handset on or off 20 Getting started 10 To switch the handset on 20 Location 10 Make an external call 20 Setting up 10 Pre dialling 20 Setting up for multiple packs 12 Endacall 20 Using your Telstra Slim on a Broadband Receive a call 20 ADSL line Earpiece handsfree volume 21 Date and time 13 Mute 21 Set date and time manually 1 Handsfree 21 Make a handsfree call 21 Getting to KNOW your prone Answer a callin handsfree mode 21 aang Switch to handsfree mode duringacall 21 gee 16 Redial 54 pepe ols Redial the last number called 21 page eer pe werd maeune as Redial a number from the redial list 22 GATE EEN Save a number from the redial list to the Option buttons 18 phonebook 22 Menu layout 19 Delete a redial number 22 Delete all redial numbers 22 Keypad lock 23 To lock the keypad 23 In this guide To unlock the keypad 23 To edit a Speed dial 28 Find handset Paging 23 To dial using a Speed dial 29 Message amp Call inbox 23 Settings 30 Phoneb
34. e unit with the active receive centre number is a DECT product then all handsets registered to that base unit will be able to receive text messages 5 The nese abil Select SEHD STORE 6 pies Avo cancel at any stage and return to standby mode Receiving messages When you receive a new text ea tig M icon is displayed along with HEH TEXT MSG and the base text indicator amp SMS aches Answering Machine version ili 50 Read een 1 Choose Menu TET is displayed Choose OK Press to sled IMEC and choose OK 2 Press amor EJ to select the text you want to read and choose Read 3 Press amor EY to scroll through the text 4 Choose Option and press Aor KY to select REPLY Choose OK Choose Hii to use a blank screen or ES to keep original text in the reply Enter your message Choose Option then choose OK The caller s number is ieee Choose Send ARI Choose OK Add more text if required Choose Option to Send CALL HUMEEE Choose OK The caller s number is displayed Edit the number if required Press to dial iUMHEER Choose OK Enter the nam Press J to select HUMBER ad edit number if eade Press to select GROUF and press EJ or to select the Group Choose OK to save LETE Choose OK The text is deleted ALL Choose OK Choose E to confirm or HO to cancel Te iin alee Bunun Seoon fonun 5 Press to cancel at any time and return to standby mode Edit or delete pk at 1 Cho
35. eft in your Telstra Home Messages 101 or MessageBank service To arrange connection of the Flashing Message Indicator service simply call Telstra on 13 2200 When a new message is left the ao icon will be displayed on the handset After you have listened to your message s the ao icon will disappear Telstra Home Messages 101 You can get messages from your Telstra fixed home phone when you are away from the phone busy on another call or using the Internet Callers will hear a standard greeting inviting them to leave a message To call Telstra Home Messages 101 Press F and dial 101 OR While the handset is in standby press and hold the key The handset will dial 125101 OR Press and then press and hold the ES key The handset will dial 125101 By selecting the Telstra Network Services menu you can access a range of useful pre stored numbers and further Telstra Network Features You can also access the TecHelp number 37 Telstra Network Services Pre stored Telstra Network Features e Feature Assistant eCall Wait On eCall Wait Off eCheck Call Wait eCall Return eCheck CF Immed eCheck CF Busy eCheck CF No Ans eCall Back Off eTecHelp To use Feature Assistant 1 Press Telstra 2 Press to select FEATURE ASSIST Choose OK 3 Press to call Listen for voice instructions To check or turn Call Waiting on off 1 Press BE 2 Press KZ to AEL ct CALL HAIT OM CALL HAIT OFF or CHE CALL T Ch
36. el To dial using a Speed dial 1 Press and hold the number dial button with the Speed dial you wish to dial 2 The display shows CALLIHG and the number being dialled 29 Settings Handset settings Display contrast Handset name 1 Choose Menu press fami to select SETTING and choose OK 2 HISET SETTINGS is highlighted Choose OK 3 Press EJ to select DISPLAY and choose OK 4 Press aaj or XJ to select the contrast setting Choose OK to save 5 Press J to select HAME Choose Clear to delete the current name Enter a new name 6 Choose OK to save 7 Choose Back to return to the previous menu level Adjust the display contrast to suit different lighting conditions There are 8 levels Set aname for your handset e g Donna or Office 30 Auto answer 1 Choose Menu press fami to select SETTINGS and choose OK 2 H SET SETTINISS is olginig eee Choose OK 3 Press EJ to select AUTO SHSHEF and choose OK 4 Press aaj or XJ to select OH or OFF 5 Choose OK to save 6 Choose Back to return to the previous menu level As long as you have auto answer set to ON you can answer a call by lifting the handset off the base If you have switched auto answer off you will need to press as well Auto answer ON is the default setting Handset reset 1 Choose Menu press EA to select SE and choose OK 2 H SET SETTINGS is highlighted Choose OK 3 Press X2 to select HAHDISET RESET and choose OK 4
37. elect the Speed dial number 2 to 0 you want to store the phonebook entry in and choose OK 4 If a name and number is already allocated to the Speed dial you have chosen they will be displayed To re use this Speed dial see To edit a Speed dial 5 If the Speed dial is empty HO HUMBER is displayed followed by the phonebook entries Press Mor J to select the entry you want to copy and choose OK to save 6 Choose Back to return to the previous menu level 28 To delete a Speed dial 1 Press A in standby mode 2 Choose an press Mor J to select SPEED MAL and choose OK 3 Press fax ee to select the Speed dial number you want to delete and choose OK 4 Once the name and number are displayed choose Option and press X3 to select 5 Choose OK to confirm Once the entry is successfully deleted DELETED will be displayed 6 Choose Back to return to the previous menu level To edit a Speed dial 1 Press MA in standby mode 2 Choose en press fami or KY to select SPEED MAL and choose OK 3 Press fax Arg to select the Speed dial entry you want to edit and choose OK 4 Once the entry is displayed choose Option and EIT is displayed 5 Choose OK to confirm and then press EMor EJ to select the new phonebook entry you want for that Speed Dial Choose OK to save Phonebook 6 This new name and number will replace the old name and number in the Speed dial 7 Choose Back to return to the previous menu lev
38. er use a dry cloth as this may cause a static shock Environmental e Do not expose to direct sunlight e The product may heat up when the batteries are being recharged or during prolonged periods of use This is normal However we recommend that to avoid damage you do not place the product on antique veneered wood e Do not stand your product on carpets or other surfaces which generate fibres or place it in locations preventing the free flow of air over its surface e Do not submerge any part of your product in water and do not use it in damp or humid conditions such as bathrooms e Do not expose your product to fire explosive or other hazardous conditions e There is a slight chance that your phone could be damaged by an electrical storm We recommend that you unplug the power and telephone line cord from the base for the duration of the storm Telstra accessories and replacement items For a full range of accessories and replacement items for Telstra products please call TecHelp Information Line on 1300 369 193 How many telephones can you have All items of telephone equipment have a Ringer Equivalence Number REN which is used to calculate the number of items which may be connected to any other telephone line Your Telstra Slim has a REN of 0 1 A total REN of 3 is allowed if the total REN of 3 is exceeded the telephone may not ring With different telephone types there is not guarantee of ringing even when the
39. es with two pre recorded outgoing messages Answer and Record or Answer Only alternatively you can record your own message Your answering machine is designed to answer calls after 20 rings when it is switched off This is to enable you to operate the remote access functions of your answering machine in the event your answering machine is switched off You will need to set the day date and time if you have not already done so so that you will know when each message was received If you have subscribed to Telstra Calling Number Display the date and time is set automatically when you receive your first call To set the date and time manually see page 13 The default day and time setting is Sunday 12 01 pm 42 Voice prompts Your Telstra Slim answering machine has voice prompts to help you use its settings and features Using the answering machine from the handset Switch the answering machine on off 1 Choose Menu Press J to select SHSKEF MACHINE Choose OK 2 Press J to select GHSWER OHSOFF Choose OK 3 Scroll a or Ra to select highlight IH or OFF and choose OK When switched on the handset display shows pg 4 Choose Back to return to the previous menu level Outgoing messages The outgoing message is the message a caller first hears when the answering machine answers their call There are 2 pre recorded outgoing messages to choose from see note right or you can record your own Record you
40. f Press E to end outgoing message recording If you enter the incorrect PIN code you will be allowed one further attempt If it is still incorrect you will hear Thank you for calling and Telstra Slim will hang up If no button is pressed for 8 seconds or more your Telstra Slim will hang up 47 Text messaging When you send your first text message from your Telstra Slim you will automatically be registered with the Telstra Text Messaging service In order to send and receive text messages you must ensure you have not blocked your number If you have a Silent Line or have blocked Calling Line Identification and attempt to send a message your message will be rejected To alter your service so that you can send text messages call the Telstra Fixed Phone text services on 0198339999 and use the set up menu to turn off Silent Line or Calling Line Identification blocking for text messaging ONLY At any time choose Back to go back to the previous screen or press K to cancel and return to standby mode 48 Sending messages Send a text message 1 Choose Menu TET will be displayed Choose OK 2 WRITE HEH TEXT is highlighted Choose OK 3 Use the keypad to enter Jy message Choose Option and press Aor EY to SEHD Choose OK Enter the phone number and choose Send Or choose Option to select a number from the phonebook Redial list or Calls list Press EMor EJ to select the option you want and choose
41. g Battery needs charging Onin standby mode indicates the handset is in range of the base Flashing indicates that you are moving out of range Off handset is out of range or cannot connect to the base On handsfree speaker is switched on On indicates a missed call is in the Calls list On answering machine is switched on Off answering machine is switched off Flashing indicates there is a new answering machine message M On a new text message has been received Flashing the text message mailbox is full Off all text messages have been read On alarm is set Flashing alarm time has been reached Off alarm off H The keypad is locked Handset ringer is switched off For this feature to work you must subscribe to Telstra s Calling Number Display service Call features and charges apply Getting to know your phone Base Non answering machine 1 2 position handset charging contacts Handset can be placed flat on the base or can sit in an upright position 2 Charging Lights up when handset is charging 3 Page Press to ring all registered handsets helpful for finding a missing handset see page 23 Also used during the registration process see page 53 On indicates a call is in progress N Flashing handset is ringing during gelstra incoming call ON 16 17 Getting to know your phone Navigating the menus Your Telstra Slim has an
42. he handset off the base If you have switched auto answer off you will need to press as well Auto answer ON is the default setting See page 30 Using the phone Earpiece handsfree volume During a call you can adjust the volume of the earpiece or loudspeaker There are 5 volume levels 1 Press Rm or KY to increase or decrease the volume level while in a call Mute During a call you can talk to someone nearby without your caller hearing 1 Press a while in a call The display shows MUTE OM and your caller cannot hear you 2 Press a again to unmute the microphone Handsfree Handsfree lets you talk to your caller without holding the handset to your ear It also enables other people in the room to join in the conversation over the loudspeaker Make a handsfree call 1 Dial the number then press El on the handset 45 is displayed You will then hear your call over the handset loudspeaker Press El to switch the call between the earpiece and the loudspeaker 2 Press Pe to end the call During a handsfree call press amp aorKE to change the volume Answer a call in handsfree mode When the phone rings 1 Press El on the handset The call is transferred to the handset loudspeaker Switch to handsfree mode during a call 1 During a call press Ed on the handset to put the call on the loudspeaker To switch handsfree off and return the call to the earpiece press Ed again Redial Up to 15 of the la
43. ing 38 To use Conference Call 39 To use Call Return 39 To check Call Forward Immediate 39 To check Call Forward on Busy 39 To check Call Forward on No Answer 39 To use Call Back off 39 6 To call the TecHelp Helpdesk 39 Answering machine answering machine version only 40 Answering machine base 40 Using the answering machine from the handset 42 Switch the answering machine on off 42 Outgoing messages 42 Record your own outgoing message 42 Check or delete your outgoing message 43 Answer settings 43 Call screening 44 Message playback 44 Delete all old messages 45 Using the answering machine at the base 45 Switch on off 45 Message playback 45 Remote access 46 To enable disable remote access 46 If you forget to switch on your answering machine 46 Operating your answering machine remotely 47 In this guide Text messaging 48 Help 55 Sending messages 48 Send a text message 48 General Information 58 Sent and saved texts are stored in the Replacing the handset batteries 58 Outbox 49 Safety 58 Using the Outbox 49 Cleaning 59 Receiving messages 50 Environmental 59 Read messages 50 Telstra accessories and replacement items 59 Edit or delete templates 51 How many telephones can you have 59 Service Centre numbers 51 Add or change Service Centre numbers 51 Product warranty amp Customer service 60 Select Send Service Centre BZ Message alert 52 Switch new message alert on or off 52
44. ional above the battery and slide the battery If this product is to be used on a broadband SETTINGS Choose OK handsets and chargers for use compartment cover back on until it clicks ADSL line then you must ensure that it is 2 Choose to select DATETIME ALARH then into place connected via an ADSL filter Using this choose OK For each additional handset and charger product on a Broadband line without an ADSL Charge the battery for at least 20 hours 3 Date Time is highlighted Choose OK 1 Insert the cable through the channel at the filter may cause problems with this product rear of the charger and insert the plug into and your Broadband service 4 The current time format is highlighted the power socket Plug the other end into Press aaj or Bj to choose 24 hour or 12 hour the mains wall power socket and switch on Date and time mode Providing you have subscribed to Telstra s 5 Choose EJ to select DATE FORMAT and press Slim Extension Charger Cling Number Display service the date ond fort choose alin or mm i 6 Choose to select ENTER TIME and enter i when you receive your first call A Ne The date and time is recorded with each ane rime 9 nee ee an ane Wer ingdnachine message uenTeCeIve 7 Choose EY to select ENTER DATE and enter the date e g 09 06 07 for 9th June 2007 8 Choose OK to save If you have not subscribed to Telstra Calling Number Display you c
45. l offer the Settings option if selected View call details 1 Press to view the most recent entry displayed at the top of the Calls list 2 Press Kor EJ to move through the list 3 Choose Option DETAILS is highlighted Choose OK 35 Telstra Network Services 4 The display shows phone number date and time of the call 5 Press fam or EY to display details about the next call 6 Choose Back to return to the previous menu level Dial from the Calls list 1 Press KB to display the Calls list The most recent entry will appear at the top of the list 2 Press mor EJ to move through the Calls list 3 Highlight the desired number and press mor J to call the number Or 1 Press EJ 2 Press amor EJ to move through the list to the entry you want 3 Choose Option Press EJ to select CALL HUMBER and choose OK 4 f eared choose Clear to edit the number first 5 Press to dial Copy a Calls list number to the phonebook 1 Press J 36 2 Press mor EJ to move through the Calls list to the entry you want 3 Choose Option Press EJ to select STORE HUMBER and choose OK 4 Enter the name 5 Press EJ to select H number if ane 6 Press Sto select SELECT GROLIF and press Eor to set the call group you want 7 Choose OK to save 8 Choose Back to return to the previous menu level F and edit the When a Calls list is open press EJ to move from the newest call to the oldest or press fai to m
46. n the screen above the right option button see diagram on page 18 In standby mode press to open the menu When using Call Waiting press to toggle between the two callers 9 RIGHT Messages amp Calls List In standby mode press to access the Calls list or answering machine messages When entering text press to move the cursor to the right When listening to answering machine messages press to skip to next message 10 J DOWN Calls In standby mode press to open and move through the Calls list When on a call press to adjust volume In menu mode press to move down through the options 11 End call Off or On In standby mode press and hold to switch the handset off on When on a call press to end the call In standby mode press and hold to switch the handset off on In menu mode press to return to standby 12 Lock In standby mode press and hold to lock unlock the keypad When entering text press to switch between upper and lower case letters 13 0 zero When storing an entry in the phonebook press and hold to enter a Pause 14 R Recall When on a call press to access dial tone Also used for Telstra s Call Back feature see page 39 15 Getting to know your phone Handset display S ET i Telstra 1 16 03 TOE Int Menu Display icons Icons can be On visible Flashing or Off not visible L Shows handset battery status Appears to be filling when the handset is chargin
47. nnected the telephone line correctly e Is the base ringer set to off e You may have a faulty line or socket Try using another socket Buzzing noise on my phone or on other electrical equipment nearby e Sometimes your Telstra Slim can interfere with other electrical equipment if it is placed too close It is recommended that you place your Telstra Slim at least one metre away from electrical appliances or metal obstructions to avoid any risk of interference e If you have an ADSL internet service ensure correct filters are installed to prevent interference Customer Helpline If you are still experiencing difficulties please call TecHelp on 1300 369 193 or email tcpsupport ingrammicro com au 57 General information Replacing the handset batteries After a time you may find that the handset battery is running out of charge more quickly This is a standard sign of wear and the battery will need replacing A replacement rechargeable Nickel Metal Hydride NiMH battery can be purchased from TecHelp line on 1300 369 193 or your local electrical retailer Slide off the battery compartment cover and remove existing battery Insert the new battery and replace the compartment cover until it clicks into place IMPORTANT This equipment requires electricity to work You will not be able to make any telephone calls when the power fails Alternative arrangements should be made for access to emergency services in times of po
48. o select SELECT HANDSET Choose OK then press to sige the handset 32 you want to ring first Choose OK The RIHG DELAY option is highlighted Press or to set the number of rings before the other handsets ring Choose OK 5 Choose Back to return to the previous menu When you have more than one handset registered to your base you can set one handset to ring before the others This allows one handset user to answer all incoming first like a receptionist Choose ALL HAHISETS if you want all handsets to ring f a LITE C T at the same time or SELECT HAHDSET to nominate a handset to ring before the others Change the Recall Time The default Recall Time is 100msec This button is used to obtain dial tone when on a call As this time setting may not work on some PABX s a selection of time setting is available using the procedure below 1 Choose Menu press A to select SETTINGS and choose OK 2 Press EJ to select BASE SETTING Choose OK 3 Press EJ to select RECALL TIME Choose OK 4 Press aaj or fa to eed the recall time option you want 5 Choose OK to save 6 Choose Back to return to the previous menu The recall time should not normally need to be adjusted from the default setting unless you are advised to do so PABX access code 1 Choose Menu press A to select SETTINGS and choose OK 2 Press to select BASE SETTING Choose OK 3 Press EJ to select FAB ate E55 Choose OK 4 Enter the c
49. ode you want then choose OK 5 Choose Back to return to the previous menu level If you enter your PABX access code your Telstra Slim will automatically enter a pause after the first digit if it matches the PABX access code If any existing code is displayed choose Clear to delete digits System PIN 1 Choose Menu press to select SETTINGS and choose OK 2 Press X2 to select BASE SETTING Choose OK 3 Press EJ to SeS SYSTEM FIH Choose OK 4 Enter the old PIN original setting 0000 and choose OK 5 Enter the new PIN and choose OK 6 Re enter the new PIN and choose OK 7 Choose Back to return to the previous menu level The System PIN is used when changing certain settings and registration deregistration The default setting is 0000 You can change this to your own preferred 4 digit number If you make a mistake choose Clear to delete digits System reset This resets your Telstra Slim to its original settings 1 Choose Menu press to select SETTIHGS and choose OK 2 Press EJ to select BASE SETTING Choose OK 3 Press J to select SYSTEM RESET Choose OK 4 Enter the G PIN and choose OK 5 Choose ES to confirm or H to cancel 6 If you select ES the handset returns to standby Choose Back to return to the previous menu level 33 Settings Date Time Alarm Set date and time Providing you have subscribed to Telstra s Calling Number Display service the date and time is set aut
50. omatically when you receive your first call 1 Choose Menu Press to select SETTINGS and choose OK 2 Press to select TATE TIMESALARM Choose OK 3 DATE TIME is highlighted Choose OK 4 Press aie to select the Time format 24 hour or 12 hour 5 Press EJ to select DATE FORI T Press aaj or A to select H Mh 6 Press to select ENTER TIME and enter the time using the 24 hour format e g 17 30 for 5 30pm If 12 hour format is chosen press ED to change between t or PH Press RS to select ENTER DAT date Choose OK to save E and enter the N O Choose Back to return to the previous menu level 34 Set alarm call 1 Choose Menu Press to select SETTINGS and choose OK 2 Press to select DATE TINESALARM OK 3 Press J to select ALARM Choose OK 4 Enter the alarm time using the 24 hour format e g 0730 for 7 30am 5 Press J to select AL as Peer Press aa or Ka to select DAILY ONCE or OFF 6 Press EJ to select RINGTONE and press GJ or 4 to select the ringtone you want for the alarm Choose 7 Choose OK to save 8 Choose Back to return to the previous menu level Stop alarm ring ven ae alarm rings the display shows ALARM The alarm rings for 60 seconds 1 Choose Stop to stop the alarm Telstra Network Services Calling Number Display If you have subscribed to Telstra s Calling Number Display service you will be able to see your caller s number on your h
51. ook 24 Handset settings 30 To store a name and number 24 Display contrast Handset name 30 To view a name and number in the Auto answer 30 phonebook 25 Handset reset 30 To check how many phonebook entries are Sounds 31 Orel 2 gt Handset ringer 31 To dial an entry from the phonebook 23 Handset beeps 31 To edit a name and or number in the Base settings 32 phonebook 25 i Copy all phonebook entries from one aan handset to another 26 e E porie cla To copy one phonebook entry from one Change the Recall Time 32 handset to another 26 PABX access code 33 To delete one entry from the phonebook 27 System PIN 33 To delete all entries from the phonebook 27 System reset 33 To edit call group name 27 Date Time Alarm 34 To change call group ringtone 27 Set date and time 34 Speed dial 28 Set alarm call 34 To copy a phonebook entry to a Speed dial28 Stop alarm ring 34 To delete a Speed dial 28 In this guide Telstra Network Services 35 Calling Number Display 35 Calls list 35 View call details 35 Dial from the Calls list 36 Copy a Calls list number to the phonebook 36 Calls list settings 36 Delete an entry in the Calls list 37 Delete entire Calls list 37 Flashing Message Indicator FMI 37 Telstra Home Messages 101 37 To call Telstra Home Messages 101 37 Pre stored Telstra Network Features 38 To use Feature Assistant 38 To check or turn Call Waiting on off 38 Using Call Waiting 38 To use Call Wait
52. oose OK 3 Press F to call Follow the spoken instructions or listen for confirmation status of your instructions 38 Call Waiting Call Waiting tells you if a new caller is trying to contact you when you are already on the phone A discreet tone alerts you to the new caller so you can answer your second incoming call by putting the first caller on hold Providing you have also subscribed to Telstra Calling Number Display and the caller has not blocked their number the screen will show the second caller s details To use Call Waiting 1 You will hear the call waiting tone and the display will show ExTERHAL CALL or the number of the caller if you subscribe to Telstra s Calling Number Display or the name if it matches an entry in your phonebook NO Choose oper The eee will show choose OK1 to answer he new call andy your first eae is put on hold Or press EJ to highlight CH JECT and choose OK Pa F E oe Ha H h LGTT Pr ee a E io ha fiia d PL i Ww Press SHTCH to toggle between the two callers 4 Press to hang up the current call Telstra Network Services To use Conference Call After accepting a Call Waiting call you can conference both external calls at the same time 1 To conference the two external calls choose 2 To Bn PENNEEN single and conference choose SIHGLE COHF To use Call Return 1 Press Telstra 2 Press to select CALL FETURH Choose OK 3 Press to c
53. ose Menu TEST is ba ages Choose OK 2 Press EJ to select TEMFLATE and choose OK 3 Press Kem or EY to select the template you want to edit or delete Choose OK MPLATE Choose OK Choose Clear to delete characters Enter your template text and choose Save TEMPLATE Choose OK Choose ES to confirm or Hi to cancel 4 Choose Back to return to the previous menu level You can change the templates to your preferred message up to a maximum of 20 characters If you delete a template without replacing the text it is marked as EMF TY All templates are restored if you reset your Telstra Slim to its default settings see page 33 Service Centre numbers To send and receive text messages you need the telephone number of Telstra s Text Messaging Service Centre If you accidentally delete the Outgoing or Incoming Telstra Service Centre numbers you will need to re enter them in order for your text service to work You can enter up to 4 Service Centre numbers two incoming and two outgoing The Outgoing Service number is 01983391 The Incoming Service number is 01983391 Add or ae service Centre numbers 1 Choose Menu TEST is spa agen Choose OK 2 Press mor KEY to select T TEST SETTINGS and choose OK 3 SERVICE CENTRE Is ip aa Choose OK 4 Press mor to select SHS CENTRE is 2 3 or 4 and choose OK 5 If necessary choose Clear to delete the current number Enter the new service centre number and choose Save 6
54. ove from the oldest call to the newest If you need to edit the number or name choose Clear to delete any unwanted characters then enter new ones using the keypad Calls list settings 1 Press EJ 2 Choose Option Press to select SETTINGS and choose OK 3 Press to select 4 5 or MIE 4 Press to select HEM CALL ALERT 5 Press aaj or 4 to select GH or OFF Telstra Network Services 6 Choose OK to save 7 Choose Back to return to the previous menu level ALL CALLS will list answered and missed calls in the Calls list HISSET CALLS will oniy list unanswered calls HEH CALL ALERT OH will cause the handset to beep when a missed call is eed When you turn the HEH CALL ALERT off you may need to clear all calls in the Calls list to stop the beep The El icon will appear in the display when a missed call is received Delete an entry in the Calls list 1 Press EJ 2 Press Kem Or J to move through the list to the entry you want 3 Choose Option Press EY to select 1 and choose OK If successful handse display shows DELETED 4 Choose Back to return to the previous menu level Delete entire Calls list 1 Press EJ 2 Choose Option Press J to select DELETE FLL and choose OK 3 Choose 4 Choose Back to return to the previous menu level to confirm or H to cancel Flashing Message Indicator FMI The Telstra Slim is designed to provide visual indication when a new message is l
55. r own outgoing mead 1 auee e Menu Press Z to select AHSHER HE Choose OK 2 Press to select QUTGOQIHG M55 and choose OK ET Bele EIT inal rid i ii Dw i ii Answering machine 3 RECORD MESSAGE is A E OK 4 Press XJ to select AHS amp REC or ANSHER OHLY and choose OK 5 Speak your announcement after the long beep Choose Save to stop recording 6 Your message is then played back If you want to delete it press during playback or choose OK to save Check or delete your outgoing menas 1 Choose Menu Press J to select AHSHEF MACHINE Choose OS 2 Press X2 to select QUTEOING MSG and choose OK 3 Press X2 to select FLAY ERE Choose OK 4 Press X2 to select ANS amp REC or AHSHER OHLY and choose OK 5 Your message is then played back If you want to delete it press during playback or choose OK to save Answer and Record The pre set Answer and Record outgoing message which allows your caller to leave a message is Hello your call cannot be taken at the moment so please leave your message after the tone Your Answer and Record outgoing message can be up to 1 minute long and will replace the pre recorded message Answer Only The pre set Answer Only outgoing message where callers hear an announcement but cannot leave a message is Hello your call cannot be taken at the moment and you cannot leave a message so please call later When recording your Answer Only message remember
56. se OK 2 HISET SETTINGS is highlighted Choose OK 53 Additional handsets 3 Press Kem Or EY to select REGISTER and choose OK 4 Press a or Ba to select the base you want Choose OK 5 Enter the ee PUN then choose OK The display shows FEGISTERING At the base 1 Press and hold The handset is automatically assigned the next available handset number Select base 1 Choose Menu press to select SETTIHGS and choose OK 2 HISET SETTINGS is highlighted Choose OK 3 Press EJ to select SELECT OK 4 BASE 1is highlighted Press a or Bj to select the base you want and choose OK BASE and choose 5 Display shows SAVED followed by the Standby screen 54 De register a handset 1 Choose Menu Press to select SETTINGS and choose OK 2 HISET SETTINGS is highlighted Choose OK 3 Press to select DE REGIST OK 4 Priten the System PIN original setting and choose OK 5 SELECT HANDSET option is highlighted Press Ai EJ to he handset you want and choose OK 6 Display shows IIE REGISTERET EF and choose 7 Choose Back to return to the a menu level If registration is not successful first time please repeat the process again in case the base registration period ran out of time If there are already 5 handsets registered to the base the registration will fail You must de register another handset before you can register the new one If your Telstra Slim handset is registered to
57. st telephone numbers called are saved in the redial list You can then select any of the numbers to redial delete or copy to the phonebook Redial the last number called 1 Press A The last number you called will be displayed 2 Press to dial the number displayed 21 Using the phone Redial a number from the redial list 1 Press fal The last number you called will be displayed 2 Press Kemi or EJ to move to the number you want to call in the redial list 3 Press to dial the selected number Save a number from the redial list to the phonebook 1 Press A then press Aor EJ to move to the number you want to save 2 Choose eepten and press J to select 3 Choose OK Use the keypad to enter a name 4 Choose EY to select H The number is displayed 5 If required press KZ to select SELECT GROUP to select a ring then press aaj or Bx to select a group 6 Choose OK The entry is saved Choose Back to return to the previous menu level 22 Delete a redial number 1 Press A The last number dialled will be displayed 2 Press Kem or EJ to select the number you want to delete 3 Choose Option DELETE is highlighted Choose OK If the phonebook is full the display shows EMORY FULL and the number will not be saved You will need to delete a number in the phonebook first See page 27 4 Choose Yes to confirm or No to cancel 5 Choose Back to return to the previous menu level Dele
58. t before you can use it again You will also hear a low battery warning beep once every 60 seconds During charging the icon will appear to be filling in the display Battery performance In ideal conditions a fully charged battery should give up to 10 hours talk time or 100 hours standby time on a single charge Note that a new battery will not reach full capacity until it has been in normal use for several days To keep the battery in the best condition leave the handset off the base for a few hours at atime Running the battery right down at least once a week will help it last as long as possible The charge capacity of the rechargeable battery will reduce with time as it wears out giving the handset less talk standby time Eventually it will need to be replaced A replacement battery pack can be obtained by contacting TecHelp on 1300 369 193 or from your local electrical retailer After charging your handset for the first time subsequent charging time is about 6 8 hours a day The battery and handset may become warm during charging however this is normal 11 Getting started Getting started Setting up for multiple packs compartment the red wire should be on Using your Telstra Slim on a Broadband Set date and time manually If you have purchased a Telstra Slim multiple the left Tuck the battery leads in the space ADSL line 1 Choose Menu and press RMA to select pack you will need to prepare any addit
59. te all redial numbers 1 Press The last number dialled will be displayed 2 Choose opion and press EJ to select ELETE ALL and choose OK 3 Choose Yes to confirm or No to cancel 4 Press K to exit and return to standby mode Using the phone Keypad lock You can lock the keypad so that it cannot be used accidentally while carrying it around To lock the keypad 1 Press and hold EX while in ae mode The handset beeps and KEYPAD LOCKED is displayed on screen To unlock the keypad 1 Press and hold EB while in standby mode The handset beeps and KEYPAD UNLOCKED is displayed on screen for 2 seconds before returning to standby mode WARNING If the keypad is locked you will not be able to dial the emergency numbers 000 until the keypad is unlocked again When the keypad is locked you can still answer incoming calls and operate the handset as normal during those calls When the call is ended the keypad lock comes on again Find handset Paging You can ring a handset to help locate it 1 Press on the base All handsets registered to the base will ring for up to 30 seconds 2 Press on the base again to stop the ringing or press a button on any handset Note If there is an incoming call during paging paging will cease and the phone will ring with the incoming call instead Message amp Call inbox Your Telstra Slim has an inbox which shows the status of your messages and calls
60. wer failure Safety e Only use the power supply included with the product Using an unauthorised power supply will invalidate your guarantee and may damage the telephone e Use only the approved rechargeable battery supplied A spare rechargeable battery can be 58 purchased from TecHelp Information Line on 1300 369 193 or your local electrical retailer e Do not open the handset except to replace the handset battery or the base This could expose you to high voltages or other risks Contact TecHelp Information Line on 1300 369 193 for all repairs e Radio signal transmitted between the handset and base may cause interference to hearing aids e It is recommended that advice from a qualified expert be sought before using this product in the vicinity of emergencuy intensive care medical equipment e Your product may interfere with other electrical equipment e g TV and radio sets clock alarms and computers if placed too close It is recommended that you place your product at least one metre away from such appliances to minimise any risk of interference e Never dispose of batteries in a fire There is a serious risk of explosion and or the release of highly toxic chemicals e Dispose of batteries as per local state requirements General information Cleaning Simply clean the handset and base with a damp not wet cloth or an anti static wipe Never use household polish as this will damage the product Nev

Telstra Slim Digital Cordless Phone

Contents

Download Pdf Manuals

Related Search

Related Contents