Inno Color Beam Z7 User Manual
Contents
1. len 7 User Instructions Rev 3 14 2013 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indi rect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent assembly installation rigging and operation of this product Europe Energy Saving Notice Energy Saving Matters EuP 2009 125 EC Saving electric energy is a key to help protecting the enviroment Please turn off all electrical products when they are not in2. Slave 2 Black Out No rc On Sound State Tor 0 Sound Sense H H 100 Pan Inverse Tilt Inverse Lw co On MENU Back Light ro Delay Ts Delay Function Delay Zs Delay 3s Delay _Red White Balance pH Green Blue 255 ri Pan ed tit Rea Green j Manual Test He White Zoom in lo E fe ool ho Auto Test Temp Fixture Time Firmware Version Yes PRO defaults No Reset ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 9 Inno Color Beam Z7 System Menu DMX Address Set the DMX Address 1 Press the MENU button until DMX Addresss is displayed press ENTER 2 X will now be displayed X represents the displayed address Press the UP or DOWN buttons to find your desired address 3 Press ENTER to confirm and then press and hold the MENU button for at least three seconds to assign Show Mode Show modes 1 4 Factory Shows 1 Press the MENU button until Show Mode is displayed press ENTER 2 Show X will now be displayed X representing a number between 1 4 Press the UP o
3. tons to adjust the value Once you have made your adjustment press ENTER 4 Repeat steps 2 3 until satisfied Manual Test with this function you can manually test the individual features 1 Press the MENU button until Manual Test is displayed press ENTER 2 Use the UP or DOWN buttons to find the functions or colors that you wish to test You can test the strobe function dimmer and zoom 3 Once you find a function or color you wish to test press the ENTER button the displayed value will begin to flash You can now adjust the values by pressing the UP and DOWN buttons ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 13 Inno Color Beam Z7 System Menu Once you have finished testing press the ENTER button 4 To exit the manual test mode press the MENU button Auto Test This function will run a self test program 1 Press the MENU button until Auto Test is displayed press ENTER 2 The fixture will now run a self test Press the MENU button to exit Temp With this function you can display the running temperature of the unit 1 Press the MENU button until Temp is displayed press ENTER 2 The current running temperature of the fixture will now be dis played Press MENU to exit Fixture Time With this function you can display the running time of the unit 1 Press the MENU button until Fixture Time is displayed press ENTER 2 The running time
4. A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 4 Inno Color Beam Z7 Installation When installing the unit the trussing or area of installation must be able to hold 10 times the weight without any deformation When installing the unit must be secured with a secondary safety attach ment e g and appropriate safety cable Never stand directly below the unit when mounting removing or servicing the unit Overhead mounting requires extensive experience including calculat ing working load limits installation material being used and perodic safety inspection of all installation material and unit If you lack these qualifications do not attempt the installation yourself These installaiton should be checked by a skilled person once a year The Inno Color Beam Z7 is fully operational in two different mounting positions hanging upside down from a ceiling or set on a flat level surface To avoid internal damage to the unit never mount the unit on its side as illustrated above Be sure this fixture is kept at least 0 5m away from any flammable materials decoration etc Al
5. ADJ Products LLC for service supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore 1 800 322 6337 published MANUEACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LEDs and lamps e Laser Products 90 Day Limited Warranty e L E D Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty and batteries which have a 180 day limited warranty ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 22 ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 23 Inno Color Beam Z7 Notes Inno Color Beam Z7 Notes ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 24 ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 25 Inno Color Beam Z7 Specifications SPECIFICATIONS Voltage 100V 240V 50Hz 60Hz LEDs 7 x 10W Osram Quad LEDs 4 in1 Power Consumption 104VV Beam Angle 10 60 Degrees Fuse 7Amp Power Cord Daisy Chain 4 Fixtures Max 120V 8 Fixtures Max 230V Weight 17 lbs 7 5Kgs Dimensions 10 5 L x 6 75 W x 13 5 H 262 x 167 x 340mm Colors RGBW Color Mixing DMX Channels 14 DMX
6. DMX 512 protocol 14 DMX Channels 3 Operating Modes Sound Active Show Mode or DMX Control Power Cord Daisy Chaining See Section Below Inno Color Beam Z7 Power Cord Daisy Chaining With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 4 fixtures maximum for 120V and 8 fixtures maxi mum for 240V After the maximum fixtures has been reached you will need to use a new power outlet They must be the same fix tures DO NOT mix fixtures Inno Color Beam Z7 Warranty Registration The Inno Color Beam Z7 carries a 2 year 730 days limited warranty Please fill out the enclosed warranty card to validate your purchase and warranty You may also register your product online at www americandj com All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number If the unit is under warranty you must provide a copy of your proof of purchase invoice Please contact ADJ customer sup port for a R A number ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 3 Inno Color Beam Z7 Safety Precautions To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the required volt age for your unit Do not attempt to operate t
7. light automatically turn off after one minute 1 Press the MENU button until Back Light is displayed press ENTER 2 Either ON or OFF will now be displayed Press the UP or DOWN buttons to select ON to keep the backlight on at all times or OFF to allow the backlight to turn off after 2 minutes Press any button to turn the backlight on again 3 Press ENTER to confirm Function Delay With this function the blackout func tion under 14 Channel mode can be delayed 1 Press the MENU button until Function Delay is displayed press ENTER 2 Either No Delay or time between 1s 3s will be displayed ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 12 Inno Color Beam Z7 System Menu This number represents the delay setting Use the UP and DOWN buttons to adjust the blackout delay Example If the delay is set to 3 seconds when you are in 14 Channel mode under DMX control and the channel 12 values are between 226 235 the fixture will move and then blackout after 3 seconds 3 Press ENTER to confirm White Balance with this function you can adjust the RGB colors to make your desired color 1 Press the MENU button until White Balance is displayed press ENTER 2 Use the UP or DOWN buttons to find the color you wish to adjust 3 Once you find the color you want to adjust press ENTER the displayed value will begin to flash Use the UP or DOWN but
8. of the fixture will now be displayed Press MENU to exit Firmware Version This will display the software ver sion 1 Press the MENU button until Firmware Version is displayed Press the ENTER button and the software vesion will be dis played 2 Press the MENU button to leave this function ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 14 Inno Color Beam Z7 System Menu PRO Default This function will restore the factory set tings 1 Press the MENU button until PRO Default is displayed press ENTER 2 Either YES or NO will now be displayed Press the UP or DOWN buttons to select YES to switch back to defualt set tings and press ENTER Reset Use this function to reset the motors 1 Tap the MENU button until Reset is displayed press ENTER 2 The fixture will now reset the motors Inno Color Beam Z7 UC3 Control Stand by The unit blackout Function 1 Sync Strobe Select 1 Hold to change Master Pan position 2 2 light strobe Show 2 Hold to change Master Tilt position 3 sound strobe 1 4 3 Hold to change Master Dimmer 4 Hold to change Slave Pan position 5 Hold to change Slave Tilt position 6 Hold to change Slave Dimmer Mode Sound LED off LED on LED fast blinking ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 15 Universal DMX Control Universal DMX Control This function allows y
9. only For longer cable runs we suggest a termina tor at the last fixture Set the Master unit to your desired operating mode On the slave units press the MENU button until Slave Mode is displayed and Press ENTER Choose either Slave 1 or Slave 2 and press ENTER See page 11 for more info 4 The slave units will now follow the Master unit on ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 16 Inno Color Beam Z7 ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 17 14 Channel Mode PAN 0 540 TILT 0 220 TILT FINE RED 0 100 GREEN 0 100 BLUE 0 100 WHITE 0 100 COLOR MACROS OFF MACRO 1 MACRO 2 MACRO 3 MACRO 4 MACRO 5 MACRO 6 MACRO 7 MACRO 8 MACRO 9 MACRO 10 MACRO 11 MACRO 12 MACRO 13 MACRO 14 MACRO 15 MACRO 16 MACRO 17 MACRO 18 ADJ Products LLC 73 76 77 80 81 84 85 88 89 92 93 96 97 100 101 104 105 108 109 112 113 116 1475100 121 124 125 128 129 132 133 136 137 140 141 144 145 148 149 152 153 156 157 160 161 164 165 168 169 172 173 176 177 180 181 184 185 188 189 192 193 196 197 200 201 204 Inno Color Beam Z7 14 Channel Mode OLOR MACROS MACROS MACRO 19 MACRO 20 MACRO 21 MACRO 22 MACRO 23 MACRO 24 MACRO 25 MACRO 26 MACRO 27 MACRO 28 MACRO 29 MACRO 30 MACRO 31 MACRO 32 MACRO 33 MACRO 34 MA
10. use To avoid power consumption in idle mode disconnect all electrical equipment from power when not in use Thank you Inno Color Beam Z7 Introduction Unpacking Thank you for purchasing the Inno Color Beam Z7 by ADJ Products LLC Every Inno Color Beam Z7 has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all accessories necessary to oper ate the unit has arrived intact In the case damage has been found or parts are missing please contact our toll free customer support number for further instructions Do not return this unit to your dealer without first contacting customer support Introduction The Inno Color Beam Z7 is part of ADJ s continuing pursuit for creating high quality affordable intelligent fixtures The Inno Color Beam Z7 is a high performance DMX intelligent moving head LED fixture This fixture is a great piece for retail stores displays mood architectural interior and exterior decoration and clubs This unit can be used as a stand alone or in a Master Slave configuration The unit can also be controlled via DMX controller This fixture is suitable for theaters studios retail stores and other similar locations Customer Support ADJ Products LLC provides a toll free cus tomer support line to provide set
11. worry about the correct power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fixture DMX data is sent as serial data that trav els from fixture to fixture via the DATA IN and DATA OUT XLR ter minals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compli ant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX Operation The Inno Color Beam Z7 can be controlled via DMX 512 protocol The Inno Color Beam Z7 is a 14 Channel DMX unit The DMX address is set on the front pan
12. 55 42 WIDE NARROW G 1500 430 204 125 86 ozs PAN TILT MOVEMENT SPEED Beamangie6o B 73 32 25 21 17 Lux MAX MIN MOVEMENT SPED VV 1680 480 217 132 91 14 RESET 0 NO FUNCTION RGBW 3680 980 440 265 160 10 14 RESET ALL 15 255 NO FUNCTION ee o cs res rs O O O IS ES _ re ee ee ee ee SS lo Y A ea VE VE VO DS DS IE Distance m 0 1 0 2 0 3 0 4 0 5 0 Dimmer i 100 7 50 10 t 0 Tie sl ms 0 Ramp Effect o 2 0S Fade Time o_ 8 1S Fade Time Trise ms Tdown ms Trise ms Tdown ms Standard 0 0 0 0 Stage 780 1100 1540 1660 TV 1180 1520 1860 1940 Architectural 1380 1730 2040 2120 Theatre 1580 1940 2230 2280 ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 20 ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 21 Inno Color Beam Z7 Fuse Replacement Inno Color Beam Z7 Warranty Locate and remove the unit s power cord Once the cord has been riel are a aida E i A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products removed located the fuse holder located inside the power socket to be free of manufacturing defects in material and workmanship for a prescribed period from Insert a flat head screw driver into the power socket and gently pry out the date of purchase see specific warranty period on reverse This warranty shall be valid onl
13. CRO 35 MACRO 36 MACRO 37 MACRO 38 MACRO 39 MACRO 40 MACRO 41 MACRO 42 MACRO 43 MACRO 44 MACRO 45 MACRO 46 MACRO 47 MACRO 48 MACRO 49 MACRO 50 MACRO 51 www adj com Inno Color Beam Z7 User Manual Page 18 ADJ Products LLC 205 208 209 212 213 216 217 220 221 224 225 228 229 232 233 236 237 240 241 244 245 248 249 252 253 255 0 19 20 24 25 64 65 69 70 84 85 89 90 104 105 109 110 124 125 129 130 144 145 149 150 164 165 169 170 184 185 189 190 204 205 209 210 224 Inno Color Beam Z7 14 Channel Mode Function COLOR MACROS MACRO 52 MACRO 53 MACRO 54 MACRO 55 MACRO 56 MACRO 57 MACRO 58 MACRO 59 MACRO 60 MACRO 61 MACRO 62 MACRO 63 MACRO 64 SHUTTER STROBING SHUTTER CLOSED OPEN STROBING FAST SLOW OPEN SLOW OPEN FAST CLOSE OPEN FAST OPEN SLOW CLOSE OPEN RANDOM STROBE OPEN RANDOM OPENING PULSE OPEN RANDOM CLOSING PULSE OPEN BURST PULSE OPEN RANDOM BURST PULSE OPEN PULSING www adj com Inno Color Beam Z7 User Manual Page 19 Inno Color Beam Z7 14 Channel Mode Inno Color Beam Z7 Photometric Chart OOOO Function SHUTTER STROBING R 7600 1700 917 500 328 995 229 OPEN G 19600 5300 2300 1340 830 230 244 BURST semangieio B 690 202 99 61 47 Lux 245 255 OPEN W 21800 6100 2680 1490 150 MASTER DIMMER RGBW 47500 12700 5000 3200 1950 100 ZOOM R 610 200 87
14. Channels Working Position Any safe working position Warranty 2 Year 730 days Auto Sensing Voltage This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 26 ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Junostraat 2 6468 EW Kerkrade Netherlands service adjgroup eu www adj eu Tel 31 45 546 85 00 Fax 31 45 546 85 99 Follow Us On El facebook com americandj twitter com americandj youtube com adjlighting
15. cted between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 5 Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for DATA transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion Conductor 3 Pin XLR Female Out 5 Pin XLR Male In Ground Shield Pin 1 Pin 1 Data Compliment signal Pin 2 Pin 2 Data True signal Pin 3 Pin 3 Not Used Do Not Use ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 8 Inno Color Beam Z7 System Menu 001 DMX Address i 512 Shov 1 Shov 2 Show Mode Shon3 Shov 4 Standard Stage Dimmer Curve Theatre SI 1 Slave Mode
16. el of the Inno Color Beam Z7 Your unit and your DMX controller require a approved DMX 512 110 Ohm Data cable for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all professional sound and lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split Figure 1 ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 7 Inno Color Beam Z7 Set Up Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON Figure 2 XLR Male Socket XLR Female Socket XLR Pin Configuration 1 Ll i 1 Ground 1 2 Cold 2 Cold i 2 1 Ground i Pin 1 Ground 1 za 4 4 i Pin 2 Data Compliment negative I 1 3 Hot 3 Hot PoSssssssssssss554 Pin 3 Data True positive Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 90 120 ohm 1 4 watt resistor which is con ne
17. his unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short e Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside e Never operate this unit when it s cover is removed e Never plug this unit in to a dimmer pack Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged e This unit is intended for indoor use only use of this product out doors voids all warranties e During long periods of non use disconnect the unit s main power e Always mount this unit in safe and stable matter e Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the point they exit from the unit e Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 22 for cleaning details e Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances inclu ding amplifiers that produce heat The fixture should be serviced by qualified service personnel when
18. l Sound State is displayed press ENTER 2 Either On or Off will now be displayed Use the UP or DOWN buttons to toggle between On and Off 3 Press ENTER to confirm your selection the press and hold the MENU button to activate Sound Sense In this mode you can adjust the sound sensitivity of the sound active mode 1 Press the MENU button until Sound Sense is displayed press ENTER 2 Press the UP or DOWN buttons to adjust the sensitivity level The sensitivity level can be adjusted between O the lowest and 100 most sensitive 3 Press ENTER to set you desired level ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 11 Inno Color Beam Z7 System Menu Pan Inverse Pan Inversion 1 Press the MENU button until Pan Inverse is displayed press ENTER Either Yes or No will be displayed 2 To activate the Pan inversion press the UP or DOWN buttons until Yes is displayed press ENTER to confim To deactivate Pan inversion select No and press Enter Tilt Inverse Tilt Inversion 1 Press the MENU button until Tilt Inverse is displayed press ENTER Either Yes or No will be displayed 2 To activate the Tilt inversion press the UP or DOWN buttons until Yes is displayed press ENTER to confim To deactivate Tilt inversion select No and press Enter Back Light with this function you can make the back
19. ot on some other DMX devices pin 2 may be hot Also check that all cables are connected E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured i ai i No warranty whether expressed or implied is given or made with respect to any accessory supplied with to the right connectors it does matter which way the inputs products described above Except to the extent prohibited by applicable law all implied warranties made and outputs are con nected by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or Unit does not respond to sound implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is 1 Quiet or high pitched sounds will not activate the unit expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product 2 Check the sound sensitivity level P This warranty is the only written warranty applicable to ADJ Products LLC Products and If problems are not resolved Contact
20. ou to use a Elatione universal DMX 512 controller to control the chases and patterns dimmer and strobe A DMX controller allows you to create unique programs tailored to your individual needs The Inno Color Beam Z7 has 14 DMX Channels 1 This function will allow you to control each individual fixture s traits with a standard DMX 512 controller See pages 17 20 for the DMX traits 2 To run your fixture in DMX mode set your desired DMX address following the directions on page 10 and the set up specifications that come with your DMX controller 3 Plug in the fixture via the XLR connections to any standard DMX controller 4 For longer cable runs more than a 100 feet use a terminator on the last fixture Inno Color Beam Z7 Inno Color Beam Z7 Master Slave Configuration Master Slave Configuration This function will allow you to link up to 16 units together and operate without a controller The units will be sound activated In Master Slave operation one unit will act as the con trolling unit and the others will react to the controlling units programs Any unit can act as a Master or as a Slave 1 Using approved DMX data cables daisy chain your units togeth er via the XLR connector on the rear of the units Remember the Male XLR connector is the input and the Female XLR connector is the output The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector
21. r DOWN buttons to find your desired show and press ENTER to confirm After pressing ENTER press and hold the MENU button for at least 3 seconds to activate Dimmer Curve In this mode you can select the dimmer curve 1 Press the MENU button until Dimmer Curve is displayed press ENTER 2 The current dimmer curve will be displayed 3 Press the UP or DOWN buttons to find your desired dimmer curve and press ENTER to confirm Slave Mode This will let you set unit as a master or slave in a master slave configuration 1 Press the MENU button until Slave Mode is displayed press ENTER Either Slave 1 or Slave 2 will be displayed 2 Press the UP or DOWN buttons until your desired slave mode ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 10 Inno Color Beam Z7 System Menu is displayed press ENTER to confim NOTE In a Master Slave configuration you can make one fix ture the Master and then set the next fixture to Slave 2 the fixtures will now have contrast movement to each other Black Out This will activate deactivate blackout 1 Press the MENU button until Black Out is displayed press ENTER 2 Either Yes or No will now be displayed Press the UP or DOWN buttons to toggle between Yes and No 3 Press ENTER to confirm your setting Sound State In this mode the unit will run in sound active mode 1 Press the MENU button unti
22. rial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the Cleaning frequency depends on the environment in which the fixture product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior operates i e smoke foo residue dust dew panen author iatioi Ma da to purchaser by ADJ Products LLGC if the product is damaged because not properly maintained as set forth in the instruction manual Inno Color Beam Z7 Troubleshooting D This is not a service contract and this warranty does not include maintnance cleaning or periodic check Listed below are a few common problems the user may encounter up During the period specified above ADJ Products LLC will replace defective parts at its expense A i with new or refurbished parts and will absorb all expenses for warranty service and repair labor by with solutions reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole Unit not responding to DMX discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect 1 Check that the DMX cables are connected properly and are wired correctly pin 3 is h
23. up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or suggestions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2941 E mail support americandj com To purchase parts online visit http parts americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact ADJ Products LLC PLEASE recycle the shipping carton when ever possible ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 2 Inno Color Beam Z7 General Instructions To optimize the performance of this product please read these operat ing instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Inno Color Beam Z7 Features RGBW Color Mixing 7 x 10W High Quatlity Osram LEDs Color Strobe Effect Color Mix Effect Pan Tilt Inversion Electronic Dimming 0 100 Dimmer Curve Built in Microphone
24. ways use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails see next page Never use the carrying handles for secondary attachment ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 5 Inno Color Beam Z7 Installation NOTICE The suitable enviromental temperature for this light ing fixture is between 25 C to 45 C Do not place this lighting fixture in an enviroment where the temperatures are under or above the temperatures stated above This will allow the fixture to run at its best and help prolong the fixture life 1 Omega holders 2 Clamp 3 Safety rope 4 Quick lock fastener Screw one clamp via a M12 screw and nut onto the Omega holder Insert the quick lock fasteners of the first Omega holder into the respective holes on the bottom of the Inno Color Beam Z7 Tighten the quick lock fasteners fully clockwise Pull the safety cable through the two slots located on the base under neath the Omega holder and then over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw ADJ Products LLC www adj com Inno Color Beam Z7 User Manual Page 6 Inno Color Beam Z7 Set Up Power Supply The ADJ Inno Color Beam Z7 contains a automatic voltage switch which will auto sense the voltage when it is plugged into a power source With this switch there is no need to
25. y if the A product is purchased within the United States of America including possessions and the fuse holder Remove the bad fuse and replace with a new one The territories It is the owner s responsibility to establish the date and place of purchase by acceptable fuse holder has a built in socket for a spare fuse be sure not to confuse evidence at the time service is sought the spare fuse with active fuse B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the product Inno Color Beam Z7 Cleani ng only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay Due to fog residue smoke and dust cleaning the internal and exter return shipping charges only to a designated point within the United States If the entire instrument is nal optical lenses must be carried out periodically to optimize light sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for output loss of or damage to any such accessories nor for the safe return thereof 1 Use a soft cloth to wipe down the outside casing C This warranty is void if the se
Download Pdf Manuals
Related Search