F Series Indoor IP User`s Manua
Contents
1. optic component directly You can use the blower to clean the dust or dirt on the lens surface Please use a dry cloth wetted by alcohol to wipe away the dust gently if it is necessary to clean Always use the dry soft cloth to clean the device If there is too much dust please use the water to dilute the mild detergent first and then use it to clean the device Finally use the dry cloth to clean the device Don t use volatile solvent like alcohol benzene thinner and etc or strong detergent with abrasiveness otherwise it will damage the surface coating or reduce the working performance of the device Dome cover is an optical device please don t touch or wipe cover surface directly during installation and use please refer to the following methods to deal with once dirt is found Stained with dirt Use oil free soft brush or hair dries to remove it gently Stained with grease or fingerprint Use soft cloth to wipe the water drop or oil gently to make it dry then use oil free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center to outward It is ok to change the cloth and wipe several times if it is not clean enough Warning Please use the standard accessories provided by manufacturer and make sure the device is installed and fixed by professional engineers Please prevent the device surface from the radiation of laser beam when using laser beam device Please do not provide two or more power supply mod2. otherwise it may cause overexposure It is not the device malfunction which will affect the longevity of CCD or CMOS Please transport use and store the device within the range of allowed humidity and temperature Please don t keep the device in a place which is wet dusty extremely hot and extremely cold and with strong electromagnetic radiation or unstable lighting Please do not allow water and other liquid falling into the camera in case that the internal components are damaged Please do not allow rain or damp to the indoor device in case fire or lightning may occur Please keep the sound ventilation in case of heat accumulation Please pack the device with standard factory packaging or material with same quality when transporting the device Heavy stress violent vibration or water splash are not allowed during transportation storage and installation 3 Operation and Daily Maintenance Please do not touch the heat dissipation component of the device directly in order to avoid scald Please do not dismantle the device there is no component which can be fixed by users themselves in the machine It may cause water leakage or bad image for the device due to unprofessional dismantling It is recommended to use the device with thunder proof device in order to improve thunder proof effect The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera Do not touch the CCD CMOS
3. 0 172 29 0 1 90 02 a9 42 20 07 172 29 2 3 255 255 0 0 172 29 0 1 90 02 49 42 0b 6d 169 254 1 46 9F F2 37 BA Login PS 172 29 2 8 a9 1c 6e d2 172 29 2 5 IP Address 172 29 2 34 2 a9 09 13 62 172 29 27 02 a9 7c 1 39 Username admin 172 29 2 4 2 a9 2b 3f a4 Password cocco 172 29 2 4t 2 29 42 63 76 Port 37777 O 172 29 2 5 2 a9 3d b8 79 g 172 29 2 3 we OK ecCancel y 2 a9 09 4b 38 12 ic 172 29 2 2 a9 42 0b 4a xe 13 irc 172 29 2 38 37777 255 255 00 172 29 0 1 00 12 34 56 78 9a we 14 wc 172 29 2 47 3777 255 255 0 0 172 29 0 1 90 02 39 42 28 70 e 15 c 172 29 2 80 ar77 255 255 0 0 172 29 0 1 90 02 09 42 08 72 e 16 irc 172 29 2 83 3777 255 255 0 0 172 29 0 1 90 02 29 34 24 03 we 17 irc 172 29 2 102 larr 255 255 0 0 172 29 0 1 90 02 29 34 b8 7e xe Figure 3 1 Step 3 Modify the camera IP address on the Net interface click Save to finish modification See Figure 3 2 for more details Figure 3 2 3 2 Login WEB Interface Note Different devices may have different WEB interfaces the figures below are just for reference please refer to the document lt lt W EB Operation Manual gt gt in the disk and the actual interface for more details Step 1 Open IE and input the modified camera IP address in the address bar Step 2 The login interface is shown below please input your user name and password Default user name is admin and password is
4. 22c202o0e Puen O Rae eR AM Gui RE stone ad 3 1 3 1 Device end to PC end ica ic sciesssssedaiuasetleiadetetiidseenianasanents 3 1 3 2 PC end to Device end ss ssssessessesseseesesessestesessessestesseseesesseseeseese 3 1 4 Alarni nt Umea ue nen We E AAEE ARARA A 4 NS Eel AON 25 sate ee ciate eee en to ot tl ok hod lad EAREN ERAAN 6 2 1 Device Installallonsituuaceecalhueleiitnnanunsninneunn nana 6 2 2 Micro SD Card NstallatOnitssscistcssssisiseatina sanacia tugudnaannee 8 Network COntiguratlonicc ndwlnnnd adn dala tee Ah hk Nae 9 3 1 ModiivIP Addi eSShnerererennanana e a aides 9 3 2 Login WEB INL Cr ae Ss scisteinisiuteinaniuininreuutainiontulereatues iia aawsa 10 1 Structure 1 1 Device External Cables Note The following figures are for reference only which are used to know each structure component and cable port function Different models may have different structure components and cables please refer to the actual product for more details i bg a 3 WY Figure 1 1 Please see Sheet 1 1 for more details about external cable functions SN_ Port Portname _ Connector Function Description a Network port Ememet Gonnect o standard Eteret cable Comeet to standard theme cable to standa
5. HD Fisheye Panorama Network Camera Quick Start Guide Version 1 2 0 Welcome Thank you for purchasing our network camera This user s manual is designed to be a reference tool for your system Please read the following safeguard and warnings carefully before you use this series product Please keep this user s manual well for future reference 1 Electrical safety All installation and operation here should conform to your local electrical safety codes Please check if the power supply is correct before operating the device The power shall conform to the requirement in the SELV Safety Extra Low Voltage and the Limited power source is rated 12V DC DC5V or AC24V in the IEC60950 1 Power supply requirement is subject to the device label Please install easy to use device for power off before installing wiring which is for emergent power off when necessary Please prevent the line cord from being trampled or pressed especially the plug power socket and the junction from the device Note Do not connect these two power supplying sources to the device at the same time it may result in device damage We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation We are not liable for any problems caused by unauthorized modification or attempted repair 2 Environment Please don t aim the device at strong light such as lighting sunlight and so on to focus
6. admin respectively click login See Figure 3 3 for more details 10 IP Camera Username Password Figure 3 3 Step 3 Install controls according to the system prompt see Figure 3 4 for the WEB main interface Please modify the administrator password as soon as possible after you successfully logged in IP Camera Ce ee seun f aom T Losowi ae l e SB E O Figure 3 4 11 Note This users manual is for reference only Slight difference may be found in user interface All the designs and software here are subject to change without prior written notice All trademarks and registered trademarks mentioned are the properties of their respective owners If there is any uncertainty or controversy please refer to the final explanation of us Please visit our website for more information 12
7. am Make sure the 3 fixture holes on chassis face the three plastic expansion bolts on the surface Take 3 self tapping screws out from the accessories bag and fix them on the three plastic expansion bolts to secure the dome on installation surface Step 4 Take up the dome protection enclosure aim the cable exit and cover the enclosure Then use the inner hex wrench from the accessories bag to fasten the 3 hex screws So far installation is completed Note Please refer to Micro SD card installation steps if you need to install Micro SD card and operate step 4 after the installation Connect the host GND to ground lead which may improve device reliability The GND locates next to exit hole on the rear side of the chassis and the GND screw is M3 2 2 Micro SD Card Installation Take down the 3 inner hex screws on the upper enclosure by using the inner hex wrench in the accessories bag find the location of Micro SD card slot according to the following figure and fasten the 3 screws on the upper enclosure after inserting Micro SD card Note Please make sure the wire connection between power panel and device motherboard is firm otherwise it may cause abnormity Make sure the 3 screws are fastened firmly after installation to prevent dust for the device Figure 2 3 3 Network Configuration The IP address of all the cameras is the same when leaving factory default IP192 168 1 108 in order to make the camera get access to the netwo
8. ce end input the voice info to the speaker or MIC and then receive the voice info sent via earphone and other devices at the pc end 1 3 2 PC end to Device end Device Connection Please connect the speaker or the MIC to the audio input port of the PC and then connect the earphone to the audio output port of the device Login the Web and then click the Talk button to enable the bidirectional talk function You can see the button becomes orange after you enabled the bidirectional talk function Click Talk button again to stop the bidirectional talk function Bidirectional talk function and on site listening function can t be used at the same time for the device Listening Operation At the pc end input the voice info to the speaker or MIC and then receive the voice info sent via earphone and other devices at the device end 1 4 Alarm Setup Note Alarm function is only supported by some models Please refer to Figure 1 5 for more details IP Camera Camera Relay Activation Network T Enable Event lay Alarm1 gt Video Detect Relay st n Working Period Setup gt Abnormality Anti Dither 0 Second 0 100 Sensor Type NO M Storage Vv system Record Information Record Delay Second 10 300 M Relay out Alarm Delay Second 10 300 T Send Email T Snapshot Default Refresh Figure 1 5 Please follow the steps listed below for alarm input and output connection Step 1 Conn
9. ect alarm input device to the alarm input of I O cable Step 2 Connect alarm output device to the alarm output of I O cable alarm output is collector open circuit output which connects 10K resistor to 3 3V externally Step 3 Open the Web set alarm input and output correspondingly Alarm input on WEB corresponds to I O cable on device When there is alarm alarm input device will generate signal of high and low level Set corresponding NO and NC inputs Step 4 Set the WEB alarm output The alarm output is for the alarm output port of the device It is the alarm output port of the I O cable Alarm input output figures Alarm Input 5 Collecting GND Figure 1 6 Alarm input When the input signal is idle or grounded the device can collect the different statuses of the alarm input port When the input signal is connected to 3 3V or it is idle the device collects the logic 1 When the input signal is grounded the device collects the logic 0 External Device Figure 1 7 When alarm output is OC it needs to increase pull up resistance externally to work normally output signal is high and low level After external pull up resistance is increased the default of output signal is high level and it switches to low level when there is alarm output The working current of alarm output port is recommended as lt 10mA The max current which is used to drive external circuit is 80mA it is advised to add a relay if it i
10. es for the device otherwise it may cause damage to the device Statement Please refer to the actual product for more details the manual is just for reference The manual will be regularly upgraded according to the product update the upgraded content will be added in the manual without prior announcement Please contact the supplier or customer service if there is any problem occurred when using the device Please contact the customer service for the latest procedure and supplementary documentation There may be deviation between the actual value of some data and the value provided in the manual due to the reasons such as the real environment is not stable and so on Please refer to the company s final explanation if there is any doubt or dispute The company is not liable for any loss caused by the operation which is not followed by the manual Before installation please open the package and check all the components are included Contact your local retailer ASAP if something is broken in your package Accessory Name Amount Network Camera 1 Quick Start Guide 1 as Installation Accessories Bag CD 1 1 Table of Contents SWIG FA tsa a Mia Ms a Naas tsa R URA A R a R EE 1 1 1 Device External Cables ssessssseeeeessessesstestesressessresrrestesressessresresressess 1 1 2 DIMENSIONS ieli ee eiretat erine oveitnetats ates ates ataeateiatetatetgtesetes ated aed 2 1 3 BIGIFeGtiOMall Valk 2e2
11. rd Ethernet cable Power input POWER poti Connect to DC 12V power input power AUDIO Adra Lpi Output audio signal to speaker and other devices OUT port AUDIO IN a input a Input audio signal receive analog audio signal from pick up and other devices Sheet 1 1 See Sheet 1 2 for more details about I O port functions Port Name Name Port Connector name Function Description Function Description Alarm input port receive the on off signal ALARM_IN1 put p g from external alarm source I O Port Alarm output port output alarm signal to 2 ALARM_OUT1 i alarm device Port Name Port SN Port Connector name Function Description Sheet 1 2 1 2 Dimensions Note The following figures are for reference only different models may have different appearances according to the figures below please refer to the actual product according to Figure 1 2 to Figure 1 4 Figure 1 2 Figure 1 3 Figure 1 4 1 3 Bidirectional Talk 1 3 1 Device end to PC end Device Connection Please connect the speaker or the MIC to the audio input port of the device and then connect the earphone to the audio output port of the PC Login the Web and then click the Talk button to enable the bidirectional talk function You can see the button becomes orange after you enabled the bidirectional talk function Click Talk button again to stop the bidirectional talk function Listening Operation At the devi
12. rk smoothly please plan the useable IP segment reasonably according to the actual network environment 3 1 Modify IP Address IP address can be acquired and modified through quick configuration tool for the cameras which are accessed via wired network it needs to connect wired network to configure wireless parameters before using wireless network cameras In this chapter it will introduce the approach of modifying IP address via Quick Configuration Tool also you can modify the IP address in the network parameters of the WEB interface please refer to the document in the disk lt lt WEB Operation Manual gt gt for more details Note Currently the quick configuration tool only supports the cameras which apply to the same network segment with computer IP address Step 1 Double click the ConfigTools exe and open the quick configuration tool Step 2 Double click the device to be configured the system will pop out the Login dialog box Enter the IP address user name password and port number of the camera and click Confirm Note The default user name and password are admin and admin respectively the default of port is 37777 See Figure 3 1 for more details QConfigtool om Refresh login Setting Upgrade Find number of devices 34 1Pv4 v ey Subnet Mask Gateway 172 29 2 6 255
13. s beyond the value 2 Installation Important Before the installation please make sure the installation surface can sustain at least 3X weight of the bracket and the camera 2 1 Device Installation Wall Mount Effect Figure 2 1 Ceiling or Wall Expansion Bolt Dome Body ST3 Self tapping Screw Dome Enclosure 8 Enclosure Set Screw Figure 2 2 Step 1 Use the inner hex wrench from the accessories bag to unfasten the 3 hex screws on the dome camera enclosure and then open the dome enclosure Step 2 Take the installation position diagram from the accessories bag and then paste it on the installation ceiling or the wall according to the monitor area Please dig three bottom holes of the plastic expansion bolts according to the diagram Take three expansion bolts from the accessories bag and then insert them to the holes you just dug and then fix firmly Note f you need to dig a hole to pull through the cable on top of installation surface you need to dig a cable exit hole on the installation surface according to the installation positioning diagram f you need to pull through the cable on the side you need to dig through the U shape exit hole on the side of chassis to form a cable access and then pull the cable through the side exit hole on the chassis Step 3 Adjust the device chassis and pull the cable through the exit hole Make TOP direction of the device identical with installation diagr
Download Pdf Manuals
Related Search