RL250S (519073) Rotating Laser User Manual
Contents
1. Automatic Self leveling Rotary Laser RL250S User Manual 5 ELECTRONIC EQUIPMENT LIMITED Maintenance and Safety While the instrument is operating be careful not to expose your eyes to the laser beam Direct xposure to a laser beam for a long time may be hazardous to your eyes The laser beam is equivalent to a class II and class 3R for HV Green Beam Operate this laser so that the laser beam plane avoids impact on the eyes of vehicle drivers or pedestrians Do not try to dismantle the instrument Have it repaired by your dealer or supplier Dismantling yourself may worsen the problem or void your warranty When attaching the instrument to a tripod make sure the instrument is securely fixed The tripod leg clamps should be securely fastened If not securely fastened or tightened the main unit could fall off or the tripod could fall over The laser should not be stored or used in extreme temperature or during rapid temperature change The laser may not function properly if used out of the ambient temperature range Store inside the carry case and place in a dry area not subject to vibration dust or high moisture If the storage temperature and ambient temperature for usage vary significantly leave the laser in its case until it can adjust to the ambient temperature The laser should be transported or carried carefully to avoid impact or vibration The laser should be stored in the carry case and packed with cushioning mater2. the laser will get back to Auto level mode and will self leveling again 4 Manual Auto indicator When Y indicator lights the slope of Y axis can be adjust when X indicator turns on the X axis slope can be adjusted 5 Head speed To change the speed of the rotating beam press the Hare Tortoise Button Speeds of Orpm 60rpm 300rpm amp 600rpm Max can be obtained 6 Tilt H I alert Enabling this mode warns the user if the laser level has been jolted 5 ELECTRONIC EQUIPMENT LIMITED 7 Tilt indicator When the light is blinking slowly the laser is in H I alert mode When the light is blinking quickly the laser level will not level as it has been jolted 8 Directional scanning Circling knob Angle of scanning includes 5 levels 0 10 45 90 180 H1 is without this function 9 Left spinning Allows the laser beam to step move counter clockwise only when the unit is in 0 RPM or scan mode H1 is without this function 10 Right spinning Allows the laser beam to step move clockwise only when the unit is in 0 RPM or scan mode H1 is without this function 11 Arrows Adjust the slope for both axis by working together with Manual Automatic button 5 ELECTRONIC EQUIPMENT LIMITED 3 Directions 3 1 Battery Installation Rechargeable and alkaline battery packs are suitable for use to power this laser To install 1 Un screw the bolt at the bottom of base part Take off the battery pack Th
3. e laser is officially c w a Ni Mh battery pack 2 Either to put the alkaline battery pack into the port or Ni Mh battery pack according to the right electrode 3 Re screw the bolt at the bottom of base part 4 H1 comes without Ni Mh battery pack 3 2 Instrument Placement 3 2 1 Horizontal scanning Place the instrument on a tripod or stable flat surface or hang it on a wall Set the unit upright and keep the slope of the instrument within the range of 5 to 5 self leveling range 3 2 2 Vertical scanning Place the instrument on the flat surface and keep the slope of instrument within the range from 5 to 5 H1 is without this function 5 ELECTRONIC EQUIPMENT LIMITED 3 3 Operations 3 3 1 Power Press the ON OFF key to switch the laser on If the power indicator light blinks the voltage of the batteries is low and batteries need to be replaced or recharged 3 3 2 Leveling When you turn the laser on it will automatically level The leveling process is indicated by a blinking laser beam After the laser has automatically leveled the laser rotating head will rotate at the speed of 600 RPM If the instrument is placed improperly or the slope of instrument exceeds the range of 5 to 5 the mode indicator and the laser beam will blink at the same time Note The instrument will shut down automatically if the unit exceeds the self leveling system range for more then 5 minutes 3 3 3 Spinning 1 Continuous spinning Pres
4. econds 1mm 10m Self leveling range 5 Operate TANGE NIT delene 500m with detector Diameter Four head speeds 0 60 300 600 R P M Four scan widths 10 45 90 180 Wavelength 635nm HV Class II Bright visible beam Wavelength 535nm HV Green Class 3R IR Remote control Available distance 20 m Operation temperature 20 C 50 C 4 F 122 F DC 4 8 6V Power supply 4xsub C NI MH battery or 4xsub C Alkaline battery Continuance working time Approx 50hr Ni MH Approx 40hr Alkaline Waterproof and dustproof IP 55 Dimension 160 L X 160 W X 185 H mm Weight 2 7kg 23
5. een A wall and B wall Tripod near Wall A Distance should follow the instructions on illustration Switch the instrument on A B Approx 30m 19 DaveBell After leveling direct the laser beam onto the close wall A Mark the centre point of the laser beam on the wall Point D A B Approx 30m Turn the instrument horizontally by 180 without changing the height after leveling direct the laser beam onto Wall B Mark the centre point of the laser beam on the opposite wall B Point II 20 DaveBell Without turning the instrument Position it close to wall B by moving the tripod Switch on the instrument and let it leveling con B Approx 30m After leveling align the height of the instrument by using tripod or by underlaying if necessary In such a manner that the centre point of the laser beam is projected exactly located the previously marked point II on wall B 21 DaveBell Approx 30m Rotate the instrument by 180 without changing the height Allow it to level in and mark the centre point of the laser beam on wall A point III Tare care that point III is as vertical as possible above or below point I The difference D of both marked points I and III on wall A amounts to the actual deviation of the plumb up beam D value should be less than 4mm 22 5 ELECTRONIC EQUIPMENT LIMITED 8 Specifications Accuracy 20 arc s
6. ep will be emitted when same level as beam a continuous pitch will sound at this point the centre of the detector is at the same alignment as the beam To get accurate results use the spirit bubble to keep the detector level The detector is powered by a standard 9v battery 16 DaveBell 7 Accuracy Checking Follow these instructions for checking axis accuracy 7 1 Horizontal surface Checking 1 Place the instrument at the point of 50m in front of wall or set a scale plate at the point of 50m away from the instrument and then adjust the level of the base approximately to aim the X1 to the wall or scale plate as depicted below H2 50 Meters 17 5 ELECTRONIC EQUIPMENT LIMITED 2 Allow the unit to level and begin rotating Mark the beam position on the wall or scale plate as H1 3 Loosen the screw of the tripod and then turn the laser 180 Allow the unit to level and rotate mark the beam position on the wall or scale plate as H2 The difference between the value of H1 and H2 should be less than 10 mm 4 Repeat the same process to check your Y axis beam Again the difference between the values of the two measurements should be less than 10 mm 5 If the difference in either axis is more than 8mm the laser should be sent to your authorized dealer for service calibration 18 DaveBell 7 2 Horizontal line checking First lay down the instrument Mount the instrument on tripod betw
7. er Frequency 50 60HZ Voltage 85 265V 3 Charging and using of the instrument can progress simultaneously 4 If keeping the instrument in storage or Leave the instrument unused for a long time the batteries dry battery or rechargeable battery needs to be taken out 5 Brand new rechargeable batteries or long time unused rechargeable batteries need to be recharged and discharged three times to attain the capacity required 14 DaveBell 5 Remote The remote control of the instrument adopts the infrared technique Aim the aperture of infrared ray to the instrument as depicted below to bring remote controlling into function Available distance indoor 30M outdoor 20M The keypad panel includes 9 keys the indicator on the RC will wink to show the operating signal has been sent out once pressing any key Functions fulfilled by the remote as follows 1 Spinning Operating method referring to 3 3 3 2 Directional scanning Operating method referring to 3 3 4 3 Slope adjustment Operating method referring to 3 3 5 15 DaveBell 6 Detector The detector will pick up a spinning beam when it crosses the electronic sensor window The detector has 3 buttons a On off button b A Sound button with 3 settings off low high c A sensitivity button This will either give a narrow or a broader range of detection When the detector is too high a slower beep will be emitted when too low a fast be
8. ial Always handle the laser with care 1 What is included with your RL250S 5 ELECTRONIC EQUIPMENT LIMITED Your RL250S includes the following parts Main Instrument Detector and Bracket Remote Control Charger Target Glasses Hard Case with Foam Insert Extra Alkaline Battery Pack c w 4xAA Alkaline batteries Wall Mount Bracket Please contact your supplier if any of the above parts are missing DaveBell 2 Find your way around the RL250S Plumb Up Beam Light House Optical Glass Rotating Head Control Panel Handle Base Plug Hole Plumb Down Beam 5 ELECTRONIC EQUIPMENT LIMITED 2 1 Control Panel Right Spin Direction Scan Left Spin Head Speed Arrow Area Manual Auto H I Alert 5 Switch ON OFF 5 ELECTRONIC EQUIPMENT LIMITED 2 2 Utilities of Panel 1 Switch ON OFF Powers the laser up or down 2 Power indicator When the light is on the instrument is on 3 Manual Automatic The laser will initially enter into self leveling mode after be powered on Press Manual Auto for once the device enter into manual mode in the meanwhile the slope of Y axis can be adjusted by up and down arrows on keypad panel while press Manual Auto again the slope on X axis can be set up by two arrows on panel In these period the other functions such as scanning left spin or right spin are also available but without accuracy When press Manual Auto the third time
9. s a Aim the Y1 beam to the direction of the slope required b Press the arrowor to move the laser beam up or down until the beam line get to its required position 3 Quit slope adjustment mode Press Manual Automatic key again After mode goes off the instrument will exit the slope adjustment mode manual mode and will start to self level again Y2 X2 Y1 DaveBell 3 3 6 Vertical Lines Once the instrument is in the position shown above The instrument will Auto level and start spinning giving a Vertical beam 12 DaveBell ELECTRONIC EQUIPMENT LIMITED 4 Power Plug Indicator Charger 5 ELECTRONIC EQUIPMENT LIMITED Insert the charger into the mains and the charging socket into the instrument or the battery pack Turn on the power The charger will show one of 3 modes Red flashing light Battery not charging Red light Battery on Charge Green light Battery charged If the red light shows check the connection If the light is flashing please wait for charging to complete Once the green light shows the instrument is fully charged charging normally takes 7 hours to give 20 hours of use Either Ni Mh battery pack the standard one or Alkaline battery pack is available to work as power supply Notices 1 Using the standard rechargeable batteries of the instrument recharging will be finished within 8 hours 4x5000mAh Ni Mh batteries 2 Power required for the charg
10. s the Key Rotational speed adjustment to control the spinning speed of the laser module If press the key repeatedly the spinning speed of the laser module will continuously change as follows 0 60 300 600 0 r p m 5 ELECTRONIC EQUIPMENT LIMITED 2 Stepping spinning Press the speed key until it is at 0 r p m the laser module will stop spinning Press the Key Right Spinning the laser module will move clockwise Press the Key Left Spinning the laser module will move counter clockwise 3 3 4 Directional scanning 1 Press the Speed key until it is at 0 r p m the laser module will stop spinning Press the Key Directional scanning the laser module will scan directionally If press the key repeatedly the angle of scanning of laser module will continuously change as follows 0 10 45 90 180 0 2 Press the Key Left spinning or the Key Right spinning to change the direction of scanning 3 3 5 Slope Adjustment When the instrument is set upright for horizontal rotation the slope of the X axis and Y axis can be adjusted by using manual mode To select manual mode Press the Key Manual Automatic the instrument will first enter into the mode of manual adjustment 1 Slope of X axis a Aim the X1 beam to the direction of the slope required 10 DaveBell ELECTRONIC EQUIPMENT LIMITED b Press the arrowl lor ito move the laser beam up or down until the beam line get to its required position 2 Slope of Y axi
Download Pdf Manuals
Related Search