71-07090-000-E D202 User Guide Cards.pmd
Contents
1. Ady Je9 gun euo Julod Jug 9u0j Yoys ujod 9u0j ou 3461 o1 Ssald peuinbau d jouM Q epoossed 1913 Z 91 euo suado 100p e uauw auo e punos pue 3utod ay UJajs s yas ued 104 paps sjulod S3023eM 40 51 5 5 jno usu M Selecting Watch Points To select points to watch 1 Press 2 Lights come on to indicate watched points You cannot watch fire points They are always on 3 Enter your passcode Owner typerequired 4 Press 1 to to select and deselect points Key 1 for Point 1 and so on To select or deselect all points press 9 5 Press after selecting points System Test Press 1 and then enter your passcode to conduct a system test Besureto contact your alarm company before you begin Watch Test e Change Passcode 1 Press 5 _ If you hear the error tone your system doesn t have the Change Passcode feature Enter your passcode The light showing your code number 1 to 8 turns on and the Part light begins flashing Enter a new passcode with the same number of digits as your old code If the error tone sounds start over Try a different new passcode Enter your new passcode again The OK tone sounds and the system leaves passcode change mode If theerror tone sounds st2. Test System Weekly See Watch Test Points Med JI Turn System Off Enter your passcode to turn the system off and silence alarms Turn System On Press 9 Exit Delay begins If Error Tone sounds see Bypass Points on the card below Turn System Part On Press 0 Exit Delay begins If Error Tone sounds see Bypass Points on the card below Turn System All On No Delay Pres 9 9 UseNo Delay when you re staying home If Error Tone sounds see Bypass Points on the card below TurnSystemPartOn No Delay Pres 0 0 UseNo Delay when you re staying home If Error Tone Sounds see Bypass Points on the card below Bypass Points An open door or window is an example of a faulted point Use Bypass to turn the system on with a faulted point 1 A Pres 9 Jor C0 To turn the system All Part on The lights for faulted points blink The lights for other points are on solid The exit tone begins if there are no faulted points Press the key for the point you want to bypass For example if you want to bypass point 5 press the 5 key The point light goes off The exit tone starts when all faulted points are bypassed If you bypass a point in error press and start over at step 1 Exit now or turn the system on with No D day by pressing C9 C0 Ja second time The All or Part light blinks showing points arebypassed Turni
3. art over Show Users The Show User mode shows each user s code type on lights 1 to 8 User 115 light 1 and so on 1 Press 6 to Show Code type Flash Owner Blink User On OneTime Off Disabled 2 Press to leave Show User A Keypad Indicators On Lights when system is All or Part On No Delay Lights when the system is All or Part On without entry or exit delay 1to8 Point lights show the status of each point On Steady Point On Blink Point faulted Door or window open Flash Alarm All Lights with the On light when the system is All On When the system is off All lights when all points areready No doorsor windows open Part Lights with the On light when the system is Part On When the system is off lights when Part points are ready OK Blink see Check System Flash see Alarm Silence Reset Change Passcode oe JI Glossary Bypass To selectively remove points from the security system temporarily Entry Delay Thetime you have to enter the building and turn your system off The system emits atone during entry delay The delay for your system 15___ Exit D elay The time you have to leave the building after you ve turned your system on The system emits a tone during exit delay The delay for your system 15 ___ Faulted Point A point that is not normal a door or window is open Flashing Light A rapidly blinking light No D
4. elay Turning the system on without entry or exit delay Point A detection device or group of devices connected to your security system Trouble A service condition that needs to be corrected such asa broken wire Blinking Light A slowly blinking light D202 71 07090 000E 09 03 2003 Bosch Security Systems
5. nce Reset JI System Tones Trouble Tone A warbletone that is on briefly then followed by a pause followed by the warble tone repeatedly Error Tone The same warble tone as the Trouble Tone but it is not repeated Fire Alarm Tone A warbletone that is on for 1 second then briefly off repeatedly Burglary Alarm Tone A constant warble tone ToSilencethe TroubleTone Press Clear The trouble tone sounds and the OK light blinks when thereis a System trouble System troubles are caused by such things as low batteries or faulted detection devices The OK light stops blinking when all troubles are cleared Use Check System to identify trouble conditions If theOK light is off your system is not operational Call your alarm company Check System Press 4 then Trouble Fire Point gt 1 to view points On Trbl Blink Bypass Trouble Non Fire Point Hold 2 to view points On Trbl Blink Bypass Power Trouble Power to system is off Operating on battery Communication Fail Check telephone line Service Required Call your alarm company Alarm Memory gt Hold 6 to view points Flash Alarm On Alarm Turning the system on resets alarm memory Check System zi 9u03 Burnpejes Jaye SsoJd p QUO sueJs osje Je9 5250 Joop sJeep nun U0 Julod Juig s
6. ng the system off clears all bypassed points On Off JI To Silence an Alarm Enter Your Passcode When there alarm the OK and point lights 1 to 8 flash Thealarm tone sounds If you enter your passcode beforethe system dials your alarm company the alarm is cancelled The OK light stops flashing OK Light Flashing An alarm has been sent to your alarm company Use View Alarm M emory to see which point caused the alarm Use Reset System to reset the OK light View Alarm Memory Press 4 to enter Check System mode Hold 6 to view alarm memory Press Clear to leave Check System Reset System Press and enter your passcode to reset the system including fire points The reset takes about 20 seconds The All Part and point lights go off during the reset If points do not reset the OK light blinks Call your alarm company for help If You Lose Track If you are unsure about the status of your system do the following ChecktheOn light If it s lit your system is on Step Outside is the only function you can perform when the system is on e If the system is off press twice to exit any function and start over Step Outside Pressing bypasses your entrance doors and sounds the exit tone when your system is On with No D day You can exit and reenter without turning your System off After you reenter press to return the System to full protection and silence the tone Alarm Sile
Download Pdf Manuals
Related Search