Quick Install Guide - EZ
Contents
1. and while the unit is powered up press the re set button near the CAT5 cable connector using a paper clip or pin and hold for at least 15 seconds The LED s on the side of the antenna will cycle when the unit accepts the reset Power Cycle or reboot the unit 8 UPGRADE FIRMWARE For the latest firmware point your browser to http ez bridge com support support htm Download the latest firmware to your PC Go to SYSTEM and then UPDATE and then browse for the new files The EZ Bridge Ultra uses 2 different firm wares Unit A 139 and Unit B 239 use different firmware images so be sure to upload the correct firmware for each individual unit Caution If you upload other firmware from different websites and if you re set to defaults you will lose all the custom settings that make the bridge work properly Always backup your configuration settings from each antenna before attempting a firmware update 9 EXPANDING THE NETWORK You can add additional EZ Bridge Ultra units to connect 3 or more buildings together To add an EZ Bridge Ultra unit to the existing EZ Bridge Ultra network you set the Wireless mode to STATION you set the same wireless security then perform a site survey and connect to the available access point 10 The units can be used in avariety of other modes but since docu mentation for the advanced modes is too extensive to cover here 9 please retrieve the documentation online at http ez bridge com support s2. damage 2 Physical damage to the external amp internal parts 2 Products that have been opened altered or defaced 2 Water damage for units that were not sealed or mounted accord ing to user manual Units that were not properly grounded Usage other than in accordance with instructions and the normal intended use Do not return any products until you receive a Return Material Authorization RMA number Products received without a valid RMA number will be rejected and returned to sender Warranty Repairs All returns must have a valid RMA number written clearly on the outside of the box Without an RMA number the shipment will be refused For customers lo cated in United States and Canada customer pays all shipping charges in curred to ship the product to Tycon Systems Tycon Systems pays shipping charges to return the product to the original purchaser For all other countries the original purchaser shall pay all shipping broker fees duties and taxes in curred in shipping products to and from Tycon Systems Provided the goods have not been modified or repair attempted by someone other than Tycon Sys tems at the option of Tycon Systems products may be returned either as re paired or replaced If it is determined that there is no fault found NFF on a unit within warranty the customer will be charged 75 USD for testing time For products out of warranty the standard NFF charge is 200 This charge will be at the discretion of
3. you turn down the Tx Power to 20dBm This is because at close range there is too much power and it has a tendency to overload the input 8 stage of the units and performance degrades gt TECH TIP You may want to play around with different settings to see what works best for your particular link The measurement you would use to compare settings would be to measure the actual through put by timing the transfer of data across the link Under the TOOLS dropdown menu select SPEED TEST 6 SITE SURVEY The site survey is a very useful tool to determine what wireless devices are within range of your EZ Bridge and could be a source of interference that could cause degraded performance Go to the TOOLS drop down menu and then select SITE SURVEY The list will show all wireless devices and relative signal strength of all the devices within the range of the EZ Bridge 7 FACTORY DEFAULTS If at any time the system stops working because of changes made to the settings you can get back to the origi nal settings by resetting to factory defaults Go to SYSTEM then RE SET TO DEFAULTS You will need to reset both sides of the link in this way Always reset the remote unit first and the local unit second Any customized settings will be lost once this process is initiated lf you cannot access the web page on the unit you can do a manual reset on the antenna feed You will need to remove the cable door from the back of the antenna
4. Antenna Beamwidth 8 deg Hor 8 deg Vert Antenna F B gt 23dB Vertical or Horizontai Power Over Ethernet INPUT 100 240VAC 50 60Hz Inserter OUTPUT 24VDC 0 5A l f 12 84 dia x 10 326mm 15 7 dia x 10 400mm PimenSionS LAW dia x 254mm dia x 254mm System Weight 19 Ib 8 6 kg 20 Ib 9 1 kg Ethernet Connector Shielded RJ45 Mout Pole up to 2 25 dia or Wall Operating Temperature 22 to 167Deg F 30 to 75 Deg C Humidity O to 100 RH A Gi vecliiGn 100MPH 23lbs 125MPH 35lbs ne N AL in a lt X SM Azimuth Elevation 2 IP ADDRESS The units ship with DHCP enabled so they will try to get their IP Address from your router The fallback default IP addresses for the EZ Bridge are Unit A 192 168 1 139 and Unit B 192 168 1 239 To access the EZ Bridge your computer IP address must be on the same subnet ie 192 168 1 xxx gt TECH TIP Download the EZ Ultra Discovery Tool from http ez bridge bridge com support support htm This tool will assist you in finding the EZ Bridge Ultra on the network and allow you to access the web control panel of the unit to make any changes 3 SECURITY Security is pre configured with system passwords WPA2 encryption and Mac Address verification pre set This is so that you can setup a plug and play link and have confidence that the link is secure and that your data and network are safe Once you feel comfort able with the system and
5. Tycon Systems The RMA number is valid for 14 days from date of issue The product must be received by the repair depot within these 14 days or the shipment may be refused Shipping and Damage Claims All shipping damage claims are the purchaser s responsibility Inspect each shipment upon delivery and IMMEDIATELY report all damage to the carrier There may be time limits and inspections may be required 8000038 Rev 1 EZ Bridge Ultra Qwik Install Guide 12
6. Wireless EZ Bridge Ultra gt Ultra High Performance Point to Point Wireless Bridge System Shielded CAT5 cables to protect against EMI and ESD Achieve up to 150Mbit sec speed Link up to 8 miles with good line of sight Plug and Play Simple Installation Best security available WPA Field Proven Wireless Technology DANGER Avoid Powerlines You Can Be Killed When following the instructions in this guide to install the antenna take extreme care to avoid contact with overhead power lines lights and power circuits Contact with power lines lights or power circuits may be fatal We recommend to install antenna no closer than 20 feet from any power lines Safety For your own protection follow these safety rules c Perform as many functions as possible on the ground 2 Do not attempt to install the antenna on a rainy windy or snowy day or if there is ice or snow accumulation at the install site or if the site is wet c Make sure there are no people pets etc below when you are working on a roof or ladder 2 Watch out for any power lines which may be overhead under ground or behind walls keeping safely clear of them with the antenna ladders or any tools co See appendix for FCC RF exposure guidelines Recommended Tools 13mm Wrench Screws and screw X driver if mounting to a wall NOTE You should be familiar with using tools such as these before attempting installation of the antenna You should be comfort
7. able with working on a ladder y Getting Started It is recommended that you setup the EZ Bridge system in a single room to get acquainted with the operation of the units before in stalling outdoors You can just connect the Integrated radio feed to the POE Inserter You don t need to mount the feed to the antenna at this stage Connect 1 EZ Bridge to your router switch or computer and just power up the other EZ Bridge After powering up each unit you should be able to communicate with each unit by typing it s IP address into a standard browser You can find the IP Address using the Ultra discovery tool available at EZ Bridge com support Note We highly recommend connecting the EZ Bridge power supply to a surge protected outlet or an Uninterruptable Power Supply system We also recommend using only shielded and grounded CAT5 cable between the antenna and the POE Inserter and between the POE Inserter and the router or PC This will help prevent damage from lightning and electrical surges caused by lightning Qwik Install STEP 1 Choose a mounting location with good line of sight to the re mote location The unit can be mounted to a pole up to 2 25 diameter or to a wall using the included wall mount brackets If only short distanc es are needed the antenna can be mounted inside a building TECH TIP Microwaves travel in straight lines and they lose strength quickly when going thru buildings and tr
8. ees If there are objects in the microwave path then useable distance will be reduced If the target unit is less than 1 mile away then you wont have to worry too much about a couple obstructions but if over 1 mile and there are some obstructions in the microwave path the performance will be reduced STEP 2 Mount the Antenna be sure to mount so that the cable hole in the back of the installed plastic housing is pointing down To mount to a pole Use the supplied U Bolt and nuts Tighten nuts evenly by hand Set preliminary tilt angles Use a wrench to fully tighten the nuts To mount to a wall Mount the included wall mount bracket to any verti cal surface using customer supplied screws or bolts then mount the EZ Bridge unit to the wall mount bracket STEP 3 Connect the dish bracket to the dish reflector so that the 3 Antenna Feed Ethernet Port Reset Button F Release Button Dish Reflector Dish Bracket Alignment Pins 7 Rear Housing a wil lew Release Button Slot Cable Door square cutout in the bracket aligns with the square cutout in the dish STEP 4 Remove the rear housing from the antenna feed by pressing the release button and sliding the rear housing off the antenna feed STEP 5 Align the rear housing square feature to the square cutout in the dish Press the rear housing into position so that it snaps into place in the dish STEP 6 Mount the dish assembly to the pole or
9. electrical fields to be generated which can damage electronic equipment We have taken special care in the design of the EZ Bridge unit to ensure proper grounding of the electronics inside the enclosure to prevent damage from electrical storms Make sure that the POE Power Supply is plugged into a surge protected outlet such as a surge protected power strip or UPS inside the house Shielded CAT5 cable is also recom mended between the grounded POE Inserter and antenna 5 PAINTING The EZ Bridge unit can be painted to match a particu lar house color Only non metallic enamel or latex paints should be used If a paint with metal content is used it will block the microwaves and cause reduced performance 6 INTERNET ACCESS SHARING The EZ Bridge is the perfect equipment to share your internet access with a friend or family member up to 8 miles away Using the EZ Bridge provides a seamless con nection between networks and you can share the internet access avail able on the main network with the remote network Please take note 10 that certain internet service providers may not approve of this and in some cases they may consider this to be illegal Its best before shar ing your internet connection that you check with your internet service provider to make sure you aren t in violation of your service contract 7 COMMON MICROWAVE BARRIERS Tinted windows are made by applying a metallized film to the window If a window has tint
10. ence by one of the following measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interfer ence that may cause undesired operation IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an 11 uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body The antenna s used for this transmitter must not be co located or operating in conjunction with any other antenna or transmitter Limited Warranty All EZ Bridge products are supplied with a limited 12 month warranty which covers material and workmanship defects This warranty does not cover the following Parts requiring replacement due to improper installation misuse poor site conditions faulty power etc a Lightning
11. ing it will usually block the microwaves and cause reduced performance of the EZ Bridge Concrete walls are also a significant barrier to microwave signals Aluminum siding on houses is also a barrier to microwave sig nals Wood frame houses covered with brick or stucco are pretty trans parent to microwave signals and they will reduce the signal strength but the signal will still pass thru the structure We are bringing this up to you so you can better understand possible causes of performance issues 8 VOICE OVER IP VOIP The EZ Bridge supports all VOIP stand ards making it possible to use VOIP phones across any EZ Bridge link Appendix Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are de signed to provide reasonable protection against harmful interference in a resi dential installation This equipment generates uses and can radiate radio fre quency energy and if not installed and used in accordance with the instruc tions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is en couraged to try to correct the interfer
12. its operation we would recommend the fol lowing security changes a PASSWORD Change the user name and password on each side of the link by going to SYSTEM SYSTEM AC COUNTS and re setting the Administrator user name and pass word The default is user name EZTEAM and password link4me b ENCRYPTION Change the WPA2 encryption key by go ing to WIRELESS then WIRELESS SECURITY TECH TIP When setting encryption you must setup both sides of the link to have identical encryption keys You can setup the remote unit first and then the local unit last in order to be able to configure both units from one location across the wireless link HEX Encryption keys can use the letters A to F ato f and numbers 0 to 9 Passphrase keys can use any ASCII characters The more random the key the more se cure the code 4 CHANNELS The default channel is set to Auto The system will find the best channel each time it reboots You may want to set a fixed channel if you experience interference from local wireless systems or performance on Auto setting is inadequate To change the channel go to WIRELESS on Unit A and change the channel frequency Unit B will follow the channel automatically 5 TRANSMIT POWER Tx Power Normally there wouldn t be any reason to change the power setting The factory default setting is 23dBm 250mW which should be good for most applications If you have a very short link you will actually get better performance if
13. r Signal LED Thresholds The default values are shown below LED will light green when the wireless signal strength is above 65 dBm LED will light green when the wireless signal strength is above 73 dBm LED will light amber when the wireless signal strength is above 80 dBm LED will light red when the wireless signal strength is above 94 dBm lt gt Ethernet The Ethernet LED will light steady green when an active Ethernet connection is made and flash when there is activity O Power The Power LED will light green when the device is connected to a power source Software Settings We strongly recommend that you create a working plug and play link before making ANY changes to the soft ware settings 1 There is an HTML management system built into every EZ Bridge unit which is accessed thru a standard web browser The unit can com municate thru the Ethernet cable connection or thru the wireless con nection so you can manage remote units from a single location NOTE The device will usually go into a 2minute reboot cycle when APPLYING CHANGES During this time it will be unresponsive Technical Specifications Standards 802 11a n 802 119g n Certifications FCC CE Operating Frequency ae ue A 2405 2475MHz ZadBm 250m maxim a 96 14Mbps 94 14Mbps Receive Sensitivity 75 300Mbps 75 300Mbps 64 128bit WEP WPA WPA2 Remote Configuration By IP Address thru Wireless or Ethernet 22 dB 18 dBi
14. upport htm TECH CORNER Additional Information You May Find Useful 1 RAIN SNOW ICE The frequencies being used by the EZ Bridge will not be affected by heavy rain or falling snow You should not see any performance degradation due to inclement weather If snow or ice collects on the front of the antenna you may see some reduced perfor mance assuming you are shooting a long distance gt 2miles and the ice or snow buildup is greater than 1 thick on the surface of the anten na For this reason we suggest mounting under an eave of a house if feasible for your particular situation 2 SUN AND HEAT The EZ Bridge is constructed of all UV protect ed materials so it will survive for many years in the most extreme of so lar environments ie an Arizona rooftop during the summer The unit has been tested and qualified for constant operation at over 167 deg F ambient temperature Even though the EZ Bridge is designed for long term survivability in extreme environments we would still recommend that the unit be mounted in a more protected location like under a roof eave if possible Of course if line of sight is better with the antenna mounted in a non protected environment then we would recommend the better line of sight mounting location 3 LIGHTNING Lightning is the single worst enemy of outdoor elec tronics equipment No electronics will survive a direct strike but there are close proximity strikes that can cause huge
15. wall mount brack et at the mounting location Set approximate tilt and azimuth and tighten the two U Bolt nuts STEP 7 Insert the Antenna Feed into the dish It will snap into place Remove the cable door by pressing on the sides and pulling off Connect the CAT5 6 Cable to the antenna feed connector and then re place the cable door STEP 8 Install the POE inserters indoors near a source of 110VAC to 220VAC The POE output of the inserter connects to the CAT5 6 cable from the antenna The LAN in put of the inserter connects to a hub switch router or computer using a customer supplied CAT5 6 network cable STEP 8 Power up the EZ Bridge units Both units should connect with each other automatically Using the LED signal strength meters built into the antennas align the antennas on both sides of the link for peak signal strength The antennas have only an 8 degree beamwidth so they need to be aimed accurately for best performance It may take a couple adjustments on each side of the link to fine tune the signal strength STEP 9 As a last step install the included radome cover to the an tenna The cover snaps onto the antenna This cover will help protect the antenna components from snow and ice buildup as well as prevent nesting birds from degrading performance LEDs ee lt gt d Bl e le c cE Mee Signal In airOS you can modify the wireless signal strength threshold values for each LED on the Advanced tab unde
Download Pdf Manuals
Related Search