Re_ Pattern generation mode on X6
Contents
1. don t think you need to use Halt Pattern and on some products this caused problems Try this to see if it is necessary hope this helps Thanks Ron On 2 4 2015 2 46 AM Kevin Kloke wrote Hi Can you please send me some information on the Pattern generation mode of the X6 400M from the user manual it is not clear exactly what one can setup and what the limitations are would specifically like to see an example of a software defined pattern that can be played out 2 6 2015 7 59 AM Re Pattern generation mode on X6 400M 4 of 4 from the buffer memory Is this a separate mode to framed or PRI mode Kevin Kloke Senior Engineer CSIR DPSS Radar Applications Tel 0027 12 841 4848 Fax 0027 12 841 2455 Cell 0027 83 699 8671 Email kkloke csir co za This message is subject to the CSIR s copyright terms and conditions e mail legal notice and implemented Open Document Format ODF standard The full disclaimer details can be found at http www csir co za disclaimer html This message has been scanned for viruses and dangerous content by MailScanner and is believed to be clean Please consider the environment before printing this email 2 6 2015 7 59 AM2. Re Pattern generation mode on X6 400M 1 of 4 Subject Re Pattern generation mode on X6 400M From Tech Support lt techsprt innovative dsp com gt Date 2 4 2015 2 11 PM To Kevin Kloke lt KKloke csir co za gt Hi Kevin This explanation is from our firmware designer manager Pattern mode means the host loads waveforms to the on board memory and then just play them back from memory with any number of repetitions and jumps in between patterns as specified in the commands The Arb application software has some predefined patterns sine square triangle and also allows the use of a user defined pattern in a file The Arb exe example program uses pattern mode Select the type of waveform Waveform Type Freg MHz ena 10 95 0 Amplitude 4F5 Square Ramp Fie icon If you use Waveform Type File choose a file ini file not a file bin file The ini file contains the bin files used Arb exe setup Wavetom Type ne Triangle 1a Deak Sam 95 0 Amplitude FS Ram s Pe Examples 2ChannelSine ini Example ini files are located in the root folder C Innovative X6 400M Examples Example ini file contents EditPad Pro File Edit Project vB a ar ES ochannelSinaiai Block Bookmar eee i11le0 SineWave 2 bin Set the Base Address to 0x0 and Pattern Size to 0x1000 for the first pattern Give the pattern a name with Pattern Label Select Load Pattern Clic
3. k the Execute command button 2 6 2015 7 59 AM Re Pattern generation mode on X6 400M The pattern will load to the memory Pattem Information Mode Base Address Tag Value Play Pattem kt z Replay Pattem Pattem Size Events Repetition Count Halt Pattem Pattem Label 7 Enable Sine 1MHz Execute The patterns loaded are listed in the open frame next to the Waveform frame You can delete them or clear all of them in that frame Delete Clear All Select Play Pattern or Replay Pattern Enable Repeat if desired 2 of 4 2 6 2015 7 59 AM Re Pattern generation mode on X6 400M 3 of 4 S E a X6 400M PCle Module Arb Example Configure Setup stream Logging Eeprom Debug Stat Streaming Z Auto Preconfigure Wavefom Type Single Tone Two Tone Freg MHz 1 E Enable E Enable Active Ch Freg MHz Ecamples 2ChannelSine ini mm Ch 0 1 010 i i Amplitude 2F 5 Pattem Intonation Base Address Tag Value ot Load Pattem f aa 2 Replay Pattem Patter Size Events Repetition Count Halt Pattem Gel 000 10 Repeat Pattem Label W Enable Sine IMHz Execute Play the selected pattern with this sequence 1 Click Start Streaming Sta Sirepping 2 Click Execute Execute 3 Click Software Trigger in the upper right section of Arb exe GUI oftware Trigger Stop the selected pattern with this sequence 1 Click Stop Streaming __ Stop Streaming
Download Pdf Manuals
Related Search