User Manual
Contents
1. ps a Guangzhou China 510600 Thanks for purchasing NITECORE2. 0UV is switched off 2 Loosen the head of the torch 3 Press and hold the STROBE READY switch on the tailcap while simultaneously tightening the head 4 Once the head has been tightened the P20UV will indicate the mode that has been selected by flashing once for Tactical Mode twice for Law Enforcement Mode and three times for General Mode 5 To cycle through all three modes simply repeat the above procedures Strobe Ready 1 With batteries loaded and the light turned off press and hold STROBE READY switch on the tailcap to enter Strobe mode To exit simple release the switch 2 With the light turned on in any state press and hold STROBE READY switch on the tailcap for more than 0 5 second to enter strobe mode To exit simply press STROBE READY switch again Power Tips Two integrated LEDs built into the tail switch blink to indicate remaining battery power when the tail cap is tightened after battery installation The power indicators will blink three times when power levels are above 50 twice when power levels are below 50 and once when battery power is close to depletion NOTE When batteries are already installed and a precise power reading is required ensure the P20UV is powered down for 20 seconds before retightening the tail cap to detect battery power status Replacing Batteries Batteries should be replaced when any of the following occurs The power indicators blink rapidly output appears to be dim or the fl
3. NITECORE The All Round Flashlight Expert Features e Features dual light sources one main LED plus four secondary ultraviolet LEDs Purpose built for authentication forensics and identification applications e White CREE XM L2 T6 LED provides maximum output of 800 lumens e Four ultraviolet LEDs provide 320mW at 365nm e Maximum runtime of 15 5 hours on lowest output e Metal micro textured reflector provides a wide cone of peripheral light e Dual tail switches ensure ease of use and tactical advantages e STROBE READY provides direct access to strobe mode in any state patented e Features three selectable modes e Tail switch features integrated power indicator to display remaining battery power patented e Anti rolling design e Two way titanium steel clip included e Toughened ultra clear mineral glass with anti scratch coating e Constructed from aero grade aluminum alloy with HAIII military grade hard anodized finish e Waterproof in accordance with IPX 8 two meters submersible e Impact resistant to 1 5 meters Accessories Length 134mm 5 28 Included quality holster CR123 battery Bezel Diameter 31 8mm 1 25 magazine clip tactical ring lanyard spare Tail Diameter 25 4mm 1 O ring Weight 104grams 3 670z without battery Optional holster NTH30B remote switch RSW2 tactical lanyard NTL10 NTL20 Dimensions Battery Options Compatible Y Recommended Y Recommended NOTE
4. The above data has been measured in accordance with the international flashlight testing standards ANSI NEMAFL1 using 1 x 3 7V 2600mAh Nitecore 18650 400 battery and 2 x 3V 1700mAh LUMENS LUMENS Nitecore CR123 batteries under gt F O Fl laboratory conditions The data may vary slightly during real world use due to battery type individual usage habits and environmental factors 400 70 LUMENS LUMENS 1 5M Impact Resistant IPX 8 2m Waterproof AND Submersible NITECORE SYSMAX is a member of PLATO participating in and helping to develop the ANSI FL1 standard of measurement Product testing data is in accordance with these internationally recognized scientific standards Operation instructions Battery installation Install one 18650 Li ion battery or two CR123 Li ion batteries with the positive pole pointing forward toward the bezel NOTE Integrated LEDs within the tail switch will blink to indicate remaining battery power after battery installation Please refer to Power Tips for more information WARNING 1 Install batteries as instructed Incorrect batteries installation will stop the torch from functioning 2 The NBM1618 battery magazine holds 2 x CR123 batteries inhibits batteries movement inside the compartment and helps maintain electrical continuity 3 This product CANNOT be powered by flat top batteries 4 AVOID direct eye exposure Momentary Illumination Simply half press and hold the tail switc
5. ashlight becomes unresponsive Maintenance Every 6 months threads should be wiped with a clean cloth followed by a thin coating of silicon based lubricant Warranty Service All NITECORE products are warranted for quality DOA defective products can be exchanged for replacement through a local distributor dealer within 15 days of purchase After 15 days all defective malfunctioning NITECORE products will be repaired free of charge for a period of 60 months 5 years from the date of purchase Beyond 60 months 5 years a limited warranty applies covering the cost of labor and maintenance but not the cost of accessories or replacement parts The warranty is nullified in all of the following situations 1 The product s is are broken down reconstructed and or modified by unauthorized parties 2 The product s is are damaged through improper use 3 The product s is are damaged by leakage of batteries For the latest information on NITECORE products and services please contact your national NITECORE distributor or send an email to service nitecore com The Nitecore official website shall prevail in case of any product data changes SYSMAX ina SYSMAX Industry Co Ltd i Please follow our facebook for more info NITECORE Flashlights TEL 86 20 83862000 E ee a aa ae a a a a FAX 86 20 83882723 E mail info nitecore com Web www nitecore com Address Rm1401 Glorious Tower 850 East Dongfeng Road
6. h to turn on the flashlight and release to turn it off PZOUV User Manual Switching ON OFF To switch ON press the tail switch until a click is heard To switch OFF with the light turned on press the tail switch again until a click is heard Mode Selection The P20UV offers three different modes of illumination for different users and situations Tactical Mode this mode only provides turbo and ultraviolet outputs and is ideal for self defense emergencies and tactical operations Law Enforcement Mode this mode provides medium turbo and ultraviolet outputs Turbo is the default state This mode is designed for law enforcement officers and patrol guards General Mode default mode for first time use this mode provides low medium turbo and ultraviolet outputs With the light turned on press the STROBE READY switch on the tail to cycle through all four outputs General mode provides an intelligent memory function to ensure direct access to the setting last used when reactivated NOTE 1 When using ultraviolet output the P20UV is capable of sustaining a constant output for 13 hours with 1 x 3 7V 2600mAh 18650 Li ion battery 2 When in medium and turbo mode the P20UV will reduce output luminance automatically after 3 minutes of use to prevent batteries from overheating and extends battery longevity N WARNING Avoid eye or skin exposure to the ultraviolet light How to select a desired mode 1 Ensure the P2
Download Pdf Manuals
Related Search