T632 GB2 ML Rev.0315 X7.cdr
Contents
1. K Q VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING 20 POWER SUPPLY INSTALLATION Installing the FA GB2 power supply Install the power supply in a dry and protected place without risk of drip or water projections To avoid an electrical shock neither remove the primary protection cover nor handle the connected wire in the terminals The installation and handling of these equipments must be performed by authorised personnel and without the power connected To avoid damage the power supply has to be firmly fixed It s recommended to protect the power supply by using a thermo magnetic circuit breaker Mount the din rail to the wall with wallplugs and screws that are supplied with power supply Next place the power supply simply pressing it The power supply can be installed on a DIN 46277 To disassemble the power supply from the DIN rail use a plain screwdriver to lever the flange as shown on the picture The FA GB2 model uses 8 units over DIN rail DIN rail latch release IMPORTANT The maximum number of units that can be connected to a FA GB2 power supply is 20 monitors VESTA GB2 or 15 monitors THERA GB2 Replace the protection cover once the input terminals have been wired LOCK RELEASE INSTALLATION Installing the lock release 3 5 x2. VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING DOOR PANEL INSTALLATION 14 Configuration dip switch of the sound module EL632 GB2 The configuration dip switch is located on the left side ofthe rear part of the module push button Setto OFF when configuring is complete Factory default Description of the configuration jumper Important Do not change the factory default position ofthe configuration jumper Factory default Description of the door panel LED lights low light conditions The door panel LED lights will turn on during a call if there is low light allowing the person who called to be seen on the apartment s monitor Description of the visual indications on the door panel Visual indications on the door panel for people with impaired hearing While calling The led amp will turn on during the call and while in communication During communication The led will turn on during the communication process During door release The led p will turn on during door release End of communication The leds 4 and will turn off ON Door Panel Address Dip switches 1 and 2 OFF address 1 1 ON and 2 OFF address 2 1 OFF and 2 123456 ON address 3 1 and 2 ON address 4 QU LE Set to OFF for door panels with double push buttons and set to ON for door panels
3. 50121878 T632 682 EN REV 0315 VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING 2 INTRODUCTION First of all we would like to thank and congratulate you for the purchase of this product The commitment to reach the satisfaction of our customers is stated through the 150 9001 certification and the manufacturing of products like this one Its advanced technology and exacting quality control will do that customers and users enjoy with the legion of features this system offers To obtain the maximum profit of these features and a properly wired installation we kindly recommend you to expend a few minutes of yourtime to read this manual INDEX eee 2 yop EM EE 2 Starting recommendations TEE 2 Safety precautions oper a da AAN NAOS 3 IECIT EL E 3 um 3 Door panel description Modular sssssssssssssesssseeeeeeee een m e rennen nnn nennen ern nr inns sensn nennen nennen Doorpanel description aiii 4 Sound module description EL632 GB2 ssssssssssssssesee nn nan 5 Push buttons module description 26100 ici dd dd da dd ane 6 Embedding box positioning AN 7 Preparing the AA 7 Placetheembeddirg box uie eet etes erii eve ERE LY REL dE EYE EE 8 Assembly electro
4. 1 2 3 4 5 6 919 CODE 1 ON Anal 1 2 3 4 5 6 BUS 919 Distances and Sections THERA D2L GB2 THERA C DIGO 14 OF End of line ad THERA 1 a ANNY BUS NN BUS BUS SYNNY D2L GB2 ON lali 1 2 3 4 5 6 CODE 2 THERA CODE 0 BUS BUS Main 100 240Vac Cable Twisted 2x0 75mm 60m 60m ooooooooo CN2 CN1 FA GB2 Internal rele BUS M 99 BUS PL YN Twisted 2x1mm lt 1 Do not change the factory default position of the configuration jumper Take off jumper of all the distributors except in the last one Configuring the end of line in the last monitor Dip 6 to On Lock release max 12 Vdc 270mA 80m 80m Access door panel 2 P2 5 vas Rel 1 Ree2 5h S S S S S S 9 S SI ISIS SG 2 ar 2 Importan
5. 9 1 1 Lock release Lock release max 12 Vdc 270mA max 12 Vdc 270mA Access door panel 1 Access door panel 2 ao ao o op ao oo ao o swi apo SW1 ON OW ON a oO a Eat 123 4 5 6 123 4 5 6 NATAP JAP NA2 C2 AP AP P1 P2 BUSBUS NA1 AP AP NA2 C2 P1 P2 BUSBUS Toya Rel 1 Rel 2 A 11414 iovat Rel 1 fi Rel 2 l A 414 S S S S S S S S O O O B O 8S 919191919 9191919191919 1 1 1 Lock release max 12 Vdc 270mA Lock release max 12 Vdc 270mA 1 Important For connection of 12Va c lock release or a 2nd lock release see page 26 VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING 26 INSTALLATION DIAGRAMS Connexion of d c and a c Golmar locks release Connexion of 2 d c locks release without AP Access door panel a __ Oo To FA GB2 power supply Locks release max 12 Vdc 270mA 1 Important Do not use the AP push buttons door release if there are connected 2 d c locks release Connexion of 1 a c lock release with AP Access door panel FA GB2 power supply
6. oO tea TF 104 n i fe 2 C1 NA1 AP AP NA2 C2 AP AP P1 P2 BUSBUS SEC PRI 5 5 5 Rel 1 f Rel 2 fj A 44 4 mailia is S s js s s s js Ss Ss Ss S S S S Main 1 230Vac Lock release max 12 Vac 850mA Connexion of 2 a c locks release with AP Access door panel To FA GB2 power supply TF 104 Main 230Vac Locks release max 12 Vac 850mA VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING 27 NOTES Qolmar Sistemas de comunicaci n S A golmar golmar es www golmar es Golmar se reserva el derecho a cualquier modificaci n sin previo aviso C Golmar se r serve le droit de toute modification sans pr avis Golmar reserves the right to make any modifications without prior notice
7. Audible indications from the door panel for people with impaired vision indicating call is in progress resident unavailable door is open communication is finished and system is busy Door opening timed at 1 or 5 seconds 2 outputs for lock release separate activation Output Relay 1 a c or d c lock release operated by relay Output Relay 2 a c or d clock release operated by relay Input for external door release push button Relay 1 Input for external door release push button Relay 2 Maximum distance between power supply and furthest door panel 80m with a wire section of 1 mm Maximum distance between power supply and furthest distributor 80m with a wire section of 1 mm Maximum distance distributor and monitor 40m with a wire section of 1mm SYSTEM OPERATION To make a call the visitor should press the push button corresponding to the desired apartment an acoustic tone will be heard confirming the call is in progress once the push button has been pressed and the led will turn on If the vocal synthesis is enabled the message call is in progress will be heard confirming the call is in progress At this moment the apartment s monitor s receives the call During the call the visitor can correct his call by pressing a push button corresponding to a different apartment in which case the original call is cancelled In systems with several accesses doors the other s door panel s will be
8. ON 1 2 3 4 5 6 BUS BUS Main 100 240Vac 2 CN1 FA GB2 Cable Internal B D rele BUS M BUS PL FA GB2 Twisted 2x0 75mm 60m 60m 30m 10m S S S S Twisted 2x1mm oro gt 1 Do not change the factory default position of the configuration jumper Take off jumper of all the distributors except in the last one Configuring the end of line in the last monitor Dip 6 to On Lock release max 12 Vdc 270mA 80m 80m 40m 15m Access door panel 2 C2 P2 5 5 Rel 1 f Rel 2 Jo S S S S S S 9 S SI ISIS SG Za ar 2 Important For connection of 12Va c lock release or a 2nd lock release see page 26 VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING 23 INSTALLATION DIAGRAMS Video installation with 15 THERA monitors 4 DP GB2 distributors and Golmar 12Vd c lock release End of line vu THERA E ON ON 28 2 iS 28 THERA CODE 13 CODE 12
9. SYSTEM GB2 NEXA MODULAR BUILDING DOOR PANEL INSTALLATION 11 Double push button module coding P2 Code 1 Code 10 Code 8 Code 6 Code 4 Code 2 Code 20 Code 18 Code 16 Code 14 Code 12 Code 30 Code 28 Code 26 Code 24 Code 22 a a C a IONO O J OJO O OO OJO EL632 GB2 G E E E 119 Em e P1 e ba j P2 rao T row ETIGI AATA Code 0 20 D Code 1 EL610D Code 9 9 D Code 10 Pe Code 7 0 8 5 q 5 6 D Code 6 Code 3 Code 4 Code Q 9 3 D Code 2 Code19 9 D Code 20 T gt
10. deren I CN THERA THERA CODE 3 CODE 2 End of line ON Mikat 12345 6 BUS BUS DP GB2 S S S S S S SIS leg THERA CODE 1 CODEO Rug l Distances and Sections THERA DP GB2 THERA Main 100 240V 1 0 y CN1 CN2 rele BUS M BUS PL B Internal FA GB2 Cable A B Cc D Twisted 2x0 75mm 60m 60m 30m 10m Twisted 2x1mm 80m 80m 40m 15m Access door panel Configuring the end of line in the last distributor Switch to On C1 2 2 P1 P2 BUS Configuring the end of a Rel 1 k Rel 2 i line in the last monitor SlisisisisisSisisisisiss Dip 6 to On 1 Lock release 1 max 12 Vdc 270mA 1 Important For connection of 12Va c lock release or a 2nd lock release see page 26 VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING INSTALLATION DIAGRAMS 24 Video installation with 15 THERA monitors 8 D2L GB2 distributors and Golmar 12Vd c lock release 3 ON
11. is necessary when the distance between modules to connecting is greater due to the distribution of these modules in the door panel s VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING SOUND MODULE DESCRIPTION EL632 GB2 Sound module description EL632 GB2 Front side Color camera Leds visual indications for people with impaired hearing Leds environment low luminosity Speaker Microphone Sound module push buttons x2 Back side Internal use Internal use SE Push buttons connector ea Configuration dip switch Aq No modify internal use Push button number Pra Installation terminals GB2 Bus Installation terminals Positive ground 12Vdc output for Golmar 12Vdc lock release C1 C contact for lock release Relay 1 NA1 N O contact for lock release Relay 1 AP Input for external door release push button Relay 1 NA2 N O for lock release Relay 2 C2 C contact for lock release Relay 2 AP AP Input for external door release push button Relay 2 P1 Input for external call push button push button 1 P2 Input for external call push button push button 2 BUS Communication Bus without polarity BUS Communication Bus without polarity Note See installation diagrams for
12. vocal synthesis langua Je misie aina E E aAA nnns nter 16 Configuring the contact type for Relay 1 and Relay 2 door 16 Close the faM A AA A AAA ADA 16 Place thenameplate labels i 16 Door panel and double door panel 17 18 Closethe door panel e ERR SNR a aa 19 Power supply installation 2 20 Lockrelease Installation rca ra a e ka ad exa AA e E ERR RR EE 20 Installationdlagtrarms te 21 26 ees 27 STARTING RECOMMENDATIONS Donotuse excessive force when tightening the power supply connector screws Install or modify the equipment without the power connected The installation and handling of these equipments must be performed by authorised personnel The entire installation mustbe atleast 40cm away from any other installation Before to connect the system check the connections between door panel power supply distributors memory module MM GB2 camera unit D CAM GB2 interface GSM GB2 monitors and telephones Use RAP 2150 2x1 mm Golmar cable Doalwaysfollow the en
13. 10 40 D J o qe Codes 016 Op s 7 Em Y qe dO OD qe QD Codei5 40 D ila E come o Sees qe QD Code13 6 p mE e Code 12 Y qe Sb dO Ob Continue VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING DOOR PANEL INSTALLATION Coming from previous page EL610D de Codez0 010 4 me de Codei8 00 9D Code 17 Pe del coe 40 ED qo Code 25 9 m Ene de Code23 00 9D ee e Code 22 ume O de 40 2D Tu qoe Code 30 9 2 p nies ae 9 qe QD Code28 46 8 D Code27 O de Codl26 0 2D EET q e e D moe 508 q 9 T p e e do eb 40 pP S o Qi Em ice qe SP Code 31 dO 2D
14. 12345 6 with single push buttons ON x Set to OFF for door panels to be used in villas and set to ON for use in buildings 123456 07 UU Set to ON to configure the door release time to 5 seconds Set to OFF to configure 12345 6 the doorrelease time to 1 second ON cm Set to ON to configure see page 16 m The vocal synthesis language using the sound module s P1 push button 123456 The door release Relay 1 and Relay 2 to N O or N C using the sound module s P2 0 Calling at door panel while another door panel is communicating with more than one door panel The led jl will turn on for seconds While calling and the monitor is in do not disturb mode The led A will turn on for 4 seconds While calling apartment with no monitor or telephone The led A wil turn on for 4 seconds ON b 1 VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING 15 DOOR PANEL INSTALLATION Description of the vocal synthesis audible indications from the door panel Audible indications from the door panel for people with impaired vision If the vocal synthesis in the sound module is activated see pages 14 and 16 to configure a voice with the following messages can be heard from the door panel While calling Call is in progress Start communication You can speak now During door release Door is open End of communication Communication is finished C
15. 25 DIN 7972 y PA If the lock release will be installed in a metal door use a 3 5mm drill and ES tap the hole In case of wood door use a WM3mm drill ua DIN 563 We Q IMPORTANT The lock release must be of Golmar 12Vd c or a c See page 26 a clock release and pages 21 to 26 d c lock release VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING 21 INSTALLATION DIAGRAMS Video installation with 20 VESTA monitors 5 DP GB2 distributors and Golmar 12Vd c lock release VESTA VESTA CODE 19 CODE 18 End of line L3 Jr El Jr ES EL 123456 123 4 5 6 al 210 o i D ojl M 3 o 212 5 VESTA 2 lt CODE 17 CODE 16 ON al 2 En CN VESTA VESTA CODE 3 CODE 2 End of line 8 OFF rac 1 2 3 4 5 6 es ms Qo e o VESTA o lt ARAE 5 1 2 3 4 5 6 Distances and Sections VESTA DP GB2 VESTA Main Ld anes 100 240Vac o o o o i CN1 CN2 rele BUS M BUS PL B Internal FA GB2 Cable A B Cc D Twisted 2x0 75mm 60m 60m 30m 10m Tw
16. Code 17 0 18 Cod 15 5 6 D Code 16 Code 13 2 14 Code21 Q 9 3 D Code 12 Code29 9 D Code 30 Te Code 27 0 28 25 5 6 D Code 26 Code 23 4 Code 24 Code31 Q 9 3 D Code 22 VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING 12 DOOR PANEL INSTALLATION Single push button module coding EL632 GB2 Cl als 1 Ez B 55 alle B je D P 2 2 EJ Sa J cli P2 Hane oer AATA ELE Coo _ 4 EL610D qe coe5 00 D 1 i qe 016 Op dot e 2 Y IL qe Coe dO Ob RESUME qe QD Code
17. TE connection cable in the connector placed in the top part of the push buttons EL610D module as shown in the drawing q MT O Between push buttons modules EL610D of the same embedding box insert the short connection cable of the low connector of the first push buttons module to the top connector of the second push buttons module as shown in the drawing Between push buttons modules EL610D of different embeddingt boxes insert the short connection cable in the low connector of the last module EL610D of the first embedding box and the other end of the connection cable in the middle connector of the last push buttons module EL610D placed in the low part of the second embedding box as shown in the drawing VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING 10 DOOR PANEL INSTALLATION Plug the push buttons with the connection cable RAP 610D modules EL610D when the distance between modules to connecting is greater due tothe composition of the door panels Configuration of the push buttons code The push buttons module EL610D must be configured to assign a call code to the push buttons Make this configuration with the dip switch placed in the back side of the module Depending on the setting selected the push buttons are assigned to a specific call code To configure the monitor address call code it will be necessary to known the call code of each push button as shown in the
18. alling at one door panel while another door panel is communicating with more than one door panel System is busy try later While calling and the monitor is in Do not disturb mode Resident unavailable While calling apartment with no monitor or telephone Resident unavailable Adjusting the door panel communication volume If after starting the system the door panel audio volume seems inadequate follow these steps Call an apartment The call is received in the apartment Establish communication by pressing the E push button on the monitor Next press the same push button used to call the apartment for 3 seconds until a series of confirmation tones are heard and the door panel communication led s starts to blink Each press on the same call push button will increase the door panel volume and the led s blink speed There are 5 volume settings and the led s blink speed will vary for each Slow to fast blink low to high volume After reaching setting 5 that is maximum blink speed and volume the next setting is setting 1 thatis minimum blink speed and volume carousel mode To save the volume setting keep the same push button used to call the apartment pressed until a series of confirmation tones are heard and the door panel communication LED turns off Adjusting the vocal synthesis volume If after starting the system the vocal synthesis volume of the door panel seems inadequate follow t
19. automatically disconnected if a visitor tries to call from other door panel an acoustic tone will be heard and the led will turn on If the vocal synthesis is enabled the message system is busy try later will be heard confirming the system is busy The call lasts for 40 seconds Without alerting the visitor their image is displayed on master monitor to receive the call To view the picture on a slave monitor this function must first be activated in the monitor Ifthe call is notanswered within 40 seconds the led A will turn off and the system will be freed To establish communication press the push button ofany monitor to the apartment door panel led wil turn on If the vocal synthesis is enabled the message you can speak now will be heard confirming the communication is activated Communication will last for one and a half minutes or until the button is pressed again Once the communication has finished the leds amp and will turn off and the system will be freed If the vocal synthesis is enebled the message communication is finished will be heard in the door panel confirming the communication has finished To open the door press the door release push button during call or communication progresses with one press the door release operates for 5 seconds the led B will also turn on for 5 seconds If the vocal synthesis is enabled the message door is open will be heard in the door panel Forthe operation and configurati
20. closed information VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING SAFETY PRECAUTIONS Install or modify the equipment without the power connected The installation and handling of these equipments must be performed by authorised personnel The entire installation must be atleast 40 cm away from any other installation With power supply Do notuse excessive force when tightening the connector screws Install the power supply in a dry and protected place without risk of drip or water projections Avoid to place it near to heating sources in dusty locations or smoky enviroments Do not block ventilation holes ofthe unit so that air can circulate freely To avoid damage the power supply has to be firmly fixed avoid an electrical shock neither remove the protection cover nor handle the connected wire in the terminals CHARACTERISTICS Video door entry system with simplified installation 2 wire bus without polarity Upto 4 access door panel necessary DP GB2 distributor for more than 1 door panel access per installation Up to 20 monitors and apartments with Vesta monitor per installation Up to 15 monitors and apartments with Thera monitor per installation Up to 4 monitors per apartment Acoustic call acknowledgment signal Visual indications on the door panel for people with impaired hearing indicating call progress communication door open and system busy
21. hese steps Within 10 seconds of connecting power to the door panel press any call push button on the door panel Keep the call push button pressed until the synthesis volume is heard and the door panel communication led starts to blink Each press on the same call push button will increase the synthesis volume and the LED s blink speed There are 5 volume settings and the LED s blink speed will vary for each Slow to fast blink low to high volume After reaching setting 5 that is maximum blink speed and volume the next setting is setting 1 that is minimum blink speed and synthesis volume carousel mode To save the volume setting keep the same push button used to call the apartment pressed until a series of confirmation tones are heard and the door panel communication LED turns off VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING 16 DOOR PANEL INSTALLATION Selecting the vocal synthesis language To activate the voice synthesis of the door panel follow these steps Set dip 6 of the sound module s configuration dip switch to ON see page 14 a confirmation tone will be heard The desired language can be set using the sound module s P1 push button Each press will change the language Continue doing this until the desired language is heard Once finished set dip 6 on the configuration dip switch to OFF A confirmation tone will be heard Configuring the contact type for Relay 1 and Relay 2 doo
22. iring through the hole made in the bottom part of the embedding box Level and flush the embedding box Once the embedding box is placed remove the protective labels from the attaching door panel holes Assembly electronic modules Insert the sound module in the top part of the module frame Align the tabs on the sound module in their respective housings of the module frame and then exercise a light pressure until correct placement If there is push buttons module repeat the above process locating under the sound module as shown in the drawing Frame Frame 0 n Sound module EL632 GB2 __ Push buttons module EL610D 2 0 2 0 VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING DOOR PANEL INSTALLATION Hold the frame on the embedding box Insert the hinge that it is supplied with the product in the embedding box as shown in the drawing To hold the frame on the embedding box insert the hinge in the housings arranged for this purpose in the frame as shown in the drawing The frame can now be folded horizontally facilitating the connection and adjustments in the sound module and push buttons electronic module ir g 4 Insert the short connection cable that it is supplied with the product EL610D in the push buttons connector of the sound module and the other end of the
23. isted 2x1mm 80m 80m 40m 15m Access door panel Configuring the end of line in the last distributor Switch to On C1 2 2 P1 P2 BUS Configuring the end of a Rel 1 k Rel 2 i line in the last monitor SlisisisisisSisisisisiss Dip 6 to On 1 Lock release 1 max 12 Vdc 270mA 1 Important For connection of 12Va c lock release or a 2nd lock release see page 26 VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING 22 INSTALLATION DIAGRAMS Video installation with 20 VESTA monitors 10 D2L GB2 distributors and Golmar 12Vd c lock release VESTA CODE 19 EN ON noO EP da 123456 O O VESTA CODE 0800 2 VESTA CODE 1 ON a 1 2 3 4 5 6 O Distances and Sections VESTA D2L GB2 VESTA VESTA End of CODE 18 line ON alo 1 L 12345 O O a a a O a o a 8 2 a VESTA End of CODE 2 line oR OFF amp 4 BUS BUS CODEO line
24. le see picture Place the spacer module step 3 and insert the next module step 4 see picture B Repeat this procedure in case of door panels with one more module the maximum number of modules placed vertically is three To finish insert the second header step 5 in the lateral rods at the top part and fix it with the supplied screws see picture C A Lateral rod Lateral rod _ PIC i gt VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING DOOR PANEL INSTALLATION 18 Double door panel assembly Assembly the 1 door panel step as itis described in page 17 door panel assembly Bear in mind that the rod that will join the door panel and the door panel B have to be of the type door panel UNE rod see picture below Insert a header between door panel UNE rod and the second lateral rod at the bottom part and fix it with the supplied screws step lower module Place the spacer module step 2 3 then insert the module step 4 and insert the next module step 5 with one more modu
25. le the maximum number of modules placed vertically is three To finish insert the last header between door panel UNE rod and the second lateral rod at the top part and fix it with the supplied screws step 9 2 Lateral 6 Door panel UNE rod Door panel UNE rod Lateral rod 92 9 x 13 DIN 7981 d i 5 If the door panel is more than one module insert first the Repeatthis procedure in case of door panels gt Lateral rod 62 9 x 13 NDIN 7981 D gt gt IMPORTANT Once finished the adjustments stick the adhesive gasket that it is supplied with the set of closing heads N60XX CMPL in the door panel UNE rod VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING 19 DOOR PANEL INSTALLATION Close the door panel Fix the door panel in the embedding box with the supplied screws Finish the door panel assembly by placing the closing heads put the head on one side and then make a slight pressure on the other end to its correct placement Door panel Double door panel
26. nic MOdUIeS 0 cece tt nr nnn nee nens sehen nnn nenne 8 aes ads 9 Plug the push buttons with the sort connection 9 Plug the push buttons with the connection cable RAP 610D ssssesssseeeeeenn no eene nnne nnns 10 Push 10 Double push button module 11 single push button module coding let rt al 12 13 Configuration Cip SWitCh 14 deese pace eddy dic be 14 Description of the leds lighting low light CONAUIIONS ooooocooccccnnncniccnnoconconconccnnnnncnncnnnnnnnnon no nnne 14 Description ofthe visual indications on the door nnn nnne 14 Description of the vocal synthesis audible indications from the 15 Adjusting the door panel communication volume sssri iernare Aans nnne enne nnn nnns 15 Adjusting the vocal synthesis Volume note eerte ed entere ee d Pe ETRAS ERE EARUM dns ERE LARES RM E 15 Selecting the
27. on monitor see the corresponding monitor manual VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING DOOR PANEL DESCRIPTION NEXA MODULAR Door panel description General detail of parts for assembly the door panel Embedding boxes Frame modules Electronic Aluminium door panel modules A f RE a q G daa a GG d 7 227 a 2 0 LA u Door panel description P Screws of fixation of header x4 i Screws of fixation of embedding box x2 0 2 Closing heads 60xx n f e Lateral rod Door panel UNE rod 9 Grille module N1000 AL N1110 AL 1P j N2220 AL 2P Nexa spacer module 1 Push buttons module 1 1 Lateral rod x2 Door panel UNE rod It allows to join 2 door panels see page 18 Sound module EL632 GB2 on video systems with color camera Push buttons electronic module EL610D for 5 single push buttons or 10 double push buttons Short connection cable it is supplied with EL610D module 16 cm length For the connection of the push buttons between the sound module and the push buttons module EL610D and between push buttons modules EL610D Connection cable RAP 610D 27 cm length For the connection of the push buttons between the sound module and the push buttons module EL610D and between push buttons modules EL610D This cable
28. r release To change the contact type for door release activation of Relay 1 and Relay 2 of the door panel follow these steps Set dip 6 of the sound module s configuration dip switch to ON see page 14 a confirmation tone will be heard Use the sound module s P2 push button to select the desired contact type N O factory default or N C Each press will change the contact type A long confirmation tone will be heard if the selected contact is N O or two short tones if the selected contact is N C Stop pressing P2 when the desired tone is heard Description Once finished set dip 6 on the configuration dip switch to OFF A confirmation tone will Normally open N O be heard Normally closed N C Important The selected contact type will apply to both Relay 1 and Relay 2 Close the frame Once finished the works of wiring configuration and adjustments fix the frame in the embedding box with the supplied screws Important Before closing the door panel s make a test call to any apartment to ensure that it works correctly the label and close VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING 17 DOOR PANEL INSTALLATION Door panel assembly Insert a header in the lateral rods at the bottom part and fix it with the supplied screws step 1 then insert the module step 2 If the door panel is more than one module insert first the lower modu
29. t For connection of 12Va c lock release or a 2nd lock release see page 26 BUS BUS VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING INSTALLATION DIAGRAMS 25 Video installation with 4 access doors DP 62 distributor for door panels and Golmar 12Vd c lock release 1 1 Main 100 240Vac To distributors buiding s floor _ Em CN2 CN1 Internal FA GB2 rele BUS M BUS PL 91919 2 BUS BUS F DP GB2 D c B A e S S S S S S S S Access door panel 4 Access door panel 3 o o Oo ao po EE po CI yy oO om oo PDD 3 rj oO Sw1 Sw1 oo ON a D ao Jum 1 2 3 4 5 6 12234 5 6 C1 NA1 AP AP NA2 C2 AP AP P1 P2 BUSBUS NA1 AP AP NA2 C2 AP AP P1 P2 BUSBUS 5 5 5 5 5 5 5 avag Rel t Ret 2 l A441 davay Rel t Ret 2 fi APA S S S S S S O S O O O B O 8S 9
30. table below Push buttons module EL 610D Double push button module coding Dip switch Push buttons code Dipl Dip2 Dip3 Dip4 Dip5 Dip Dip7 Dip8 PS 5 P7 PS P9 P16 1 Off Off Off Off Off Off On 3 45 61718 19 10 x 2 Off On Off Off Off Off Off On 13 14 15 16 117 18 19 20 3 Off Off On Off Off Off Off On 23 24 25 26 27 28 29 30 Single push button module coding Dipl Dip2 Dip3 Dip4 Dip5 Dip Dip7 Dip8 On Off Off On Off Off On Off Off Off On Module configuration option Off Off Off On Off Off Off On Off Off Off Off On Off Off On ex 2s 25 gt Off Off Off Off Off Off On On 1 P1 P10 Push button 1 to push button 10 Note Sound module factory set the code 0 in P1 and 1 in P2 Important Select a different configuration option for each module EL610D Factory default VIDEO DOOR ENTRY
31. wiring pages 21 to 26 VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING PUSH BUTTONS MODULE DESCRIPTION EL610D Push buttons module description ELG10D Front side Push buttons module x10 Back side Input output push buttons connector Configuration dip switch Push buttons call code Push button number VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING DOOR PANEL INSTALLATION Embedding box positioning Fifa x 1030 1450 or The upper part of the door panel should be placed at 1 65m height roughly The hole dimensions will depend on the type of door panel Modules 1 2 3 Model NCEV90CS NCEV90C CEV90 W 99 99 99 mm H 135 5 238 328 mm D 40 56 56 mm The door has been designed to be placed under most of the environmental conditions However it s recommended to take additional cautions like covered places rainproof covers To obtain a good quality picture on video door entry systems avoid direct incidence from light sources Preparing the cables entry Break the bottom flange to pass the cables through In case of door panels with more than one embedding box break the side flanges and attach the embedding boxes using UC junctions VIDEO DOOR ENTRY SYSTEM GB2 NEXA MODULAR BUILDING 8 DOOR PANEL INSTALLATION Place the embedding box Pass the w
Download Pdf Manuals
Related Search