English CF77 User Manuals
Contents
1. Makro Detector www makrodetector com You have to follow local legislation and regulations while using the device This device must not be used in military zones residential areas and ruins Related authorities must be informed about the historical and cultural findings encountered in searches This device must only be repaired by authorized service the warranties of devices unpacked by the user or third parties are void The device and coils should not be stored in extreme cold or hot environments for a long time Suitable range of temperature 15 0 to 45C The device should not be installed or operated without reading the user manual Device and the accessories should not be submerged into water or stored in excess moisture except for the coil The device should be protected against the impact that may occur in transport CONTENTS System control unit Assembly Settings Ground setting Search and metal detection Troubleshooting and maintenance Technical specifications Thank You for Choosing Makro Detektor 10 11 13 SEARCH COILS C28 Coil and Cover Standard Package 28 cm 11 Standard coil Water resistant Double D designed for surface and deep searches C23 Coil and Cover Pro Package 23 cm 9 Water resistant Double D coil mainly designed for surface and beach searche2. MAKRO DETECTOR info makrodetector com www makrodetector com DEALER J n 1 1 WARRANTY ISO 9001 Registered MANAGEMENT
3. At the same time the device produces single type of sound without metal discrimination Iron Audio button is not active in this mode MODE 1 The device discriminates metals in this mode This is for deeper searches than MODE 2 Produces 3 different sounds to metals 2 similar sounds for non ferrous metals and gold a deeper sound for ferrous metals MODE 2 In this mode the device provides metal discrimination as well as providing more convenient operation in beaches and areas rich in minerals It is recommended that this device is used in areas rich in iron mineral beach and tillage where ground setting is not possible GROUND SETTING This is a setting done to eliminate noise and interference caused by minerals in the ground Ground setting provides the device with a higher performance and prevents it from transmitting wrong signals caused by the area rich in minerals SENSITIVITY Sensitivity setting is made to prevent noise from the ground or wrong signal sounds caused by some electromagnetic interference electrical machines radar radio TV electric lines in the environment Sensitivity setting is also the depth setting When sensitivity is set to be at maximum level depth will increase to maximum too IRON AUDIO This is a part providing ferrous metal detection setting and allowing to turn on off the sounds of these metals Iron audio is only active in Mode 1 and 2 audio is also used to eliminate misleading signals cause
4. check the signal again If no signal is received the target is in the dig part If the target is still in the ground cut the section which you think includes the target using a sharp tool This prevents the material to be scattered around and makes it easier to fill in the hole Check if the target is in the hole dig If the target is not in the hole place the detector on the ground by maintaining parallel position of the head and grasp some soil and move it around the bobbin Make sure you do not have ring watch bracelet etc on you Repeat this action till you find the target Fill the hole back when you make sure no more targets are left in the ground 12 TROUBLESHOOTING and MAINTENANCE Device is not operating at all 1 Check the battery power and connections 2 Make sure that the battery terminals are placed correctly Device receives interference 1 Make sure that the coil is tightened and wrap the bobbin wire around the shaft 2 Walls or ground might have metals if you are using the device indoor 3 There might be another detector operating and you might be close to power grid 4 Set the sensitivity 5 Ground is rich in minerals Device receives signals with uncertain intervals Intervals might mean different angle or very deep targets Do the search from different angles or dig by 5 10 cm CF77 that you have purchased does not require extensive maintenance as it is manufac tured with high quality material Foll
5. d by iron minerals in the ground VOLUME This button controls device sound level It allows the detection of weak signal sounds received by the deep or small metals by magnification Level 10 is the level where sound is the highest as this level turns all the sounds up misleading signals and ground noise will also go up Gradually turning the volume down from level 10 weakens the sound and turns it off in the end GROUND SETTING In order to switch on the device on off switch should be brought to the desired operati on position General Mode 1 or 2 A short sound will be heard showing that the device is ready to use You can switch the device off by turning the switch to OFF position 7 5em GROUND SETTING is set to 0 and SENSITIVITY is set to 10 Search is done by lifting the coil by 5 cm from the ground and moving it right to left in a parallel fashion Meanwhile in order to eliminate ground effects GROUND SETTING button is turned from left to right slowly and released when the sound stops Your ground setting is completed In case the ground being searhed has a variable nature you should do the ground setting in areas where the most ground effect is received such as rock or hole in order to minimize the ground effect while searching It should be noted that ground setting level does not exceed level 7 In these levels the device provides most stable search Over level 7 device detects iron and gold but ma
6. market may differ in operating life LOW BATTERY POWER When battery is low device sounds alarm approximately every minute When this is heard the device operates 3 4 more hours ASSEMBLY As seen in the picture fasten the S Tube by passing it through armrest and adjusting the length By holding the metal button on the upper tube mount it on the S Tube and tighten its sleeve by inserting the metal button in the socket 1 Insert the seals in the sockets at the end of the extension tube 2 Insert the extension tube in the connection port on the coil 3 Place the screw in the hole on the coil and tighten with a nut on the other side ASSEMBLY By winding coil wire as seen in the picture fasten and tighten the connector at the end of the wire in the coil input under the system box In case you want to use the battery on the device mount the belts to the cover in bottom up direc tion as seen on the picture then fasten the cover on the system box with the belts In case you want to carry the batteries on you remove the belts from the cover and fasten it to your belt Plug the battery connector with the battery socket under the system box and fasten by tightening USAGE Failing to keep the coil in a position parallel to the ground may cause faulty results USAGE 1234409 SETTINGS GENERAL In this mode the device runs at maximum depth search
7. owing are the recommendations in order to get the best performance and be able to operate the device for a long time If you will not use the device for some time remove the batteries If batteries leak serious damages may occur in battery box Your device warranty will be void becau se of user error Keep the device clean if there is dust and sand accumulation around the device wipe with a wet cloth and dry with a dry cloth Sand and dust may damage function buttons Do not rub the head on the ground Replace the protective cover if it is worn in order not to damage coil Control box is designed resistant to humidity but it is not water resistant Therefore control box should not contact water Never let the device contact petroleum based products 13 TECHNICAL SPECIFICATIONS 23 Coil 28 Coil 45 Coil System Unit and Pro Package Standard Package Pro Package Handset 23 28 cm 39 x 45 cm 460 550 gr 1 090 Total weight including standard 23 coil battery exluded 1 640 gr 3 6 lb 57 8 oz AA Alkaline or AA NiMh Rechargeable Battery Operating voltage 10V 16V Battery weight 190 gr 0 4 Ib 6 7 oz 8 pieces f AA batteries Battery box weight 180 gr 0 39 Ib 6 3 07 80 gr 0 17 Ib 2 8 oz battery box cover 2 years of warranty NOTE Battery bags and headphone are not in the scope of warranty 14 del g S
8. s Does not tire the user thanks to the lightness and provides better movement capability in narrow areas It is used to detect small metals in the surface or close to the surface Its performance and success in metal separati on make it suitable in waste metal rich areas C45 Coil and Cover Pro Package 39 x 45 cm 16 x 18 Water resistant Double D coil designed for users requiring deeper search It provides more advantage compared to standard coil It helps you to reach your targets in large areas with its large area scanning feature in searches PARTS and ACCESSORIES System Unit S Tube Extension Tube and Armrest Headphone Coil Connection Parts System Unit Connection Parts 3s Battery Box Battery Box Carry Bag Pro Package oo Cover SYSTEM CONTROL UNIT BATTERY 7 o ra 38 2 On Off 6 Coil Input Mode Selection switch 7 Battery Input Sensitivit ensitivity 8 Headphone Output Ground Setting Iron Audio Volume BATTERY Your device is delivered with AA Alkaline battery and battery box Place the batteries in the battery box considering and terminals AA Alkaline batteries are recommended for best performance Besides good quality NiMH Rechargeable batteries can be used High mA batteries provide longer use compared to low Ma batteries Fully charged alkaline batteries last maximum 30 hours Other type and brand of batteries in the
9. s will make the search more convenient for the user Moving the device both right to left and left to right on the ground will make it easier to detect the metals difficult to detect 11 SEARCH AND METAL DETECTION Interference Elimination In case there is still interference even after other settings are done ground setting iron audio it is necessary to turn sensitivity down As sensitivity setting will affect depth it should be done gradually Eliminating ferrous metals In case you do not want ferrous metals to be detected IRON AUDIO button should be set to the minimum In this way device does not produce sounds for ferrous metals in search When iron audio is turned right it will provide a deeper sound to ferrous metals If you are searching in areas rich in minerals and would like to detect ferrous metals IRON AUDIO is first set to maximum Then turned left till iron sound coming from the ground is not heard anymore This process will eliminate iron mineral sounds and allow the device to detect ferrous metals As in all metal detectors the device may not provide 100 accuracy because metals send different signals depending on their positions depth mineral intensity conductivity and shapes For example rusty sheet or can in the ground may send gold like signals In these cases it is best to dig to find out T lt Digging the target out When the target is detected dig the surface by 3 5 cm and
10. y cause depth loss for some other nn ferrous metals In these cases ground setting should be repeated by gradually decreasing sensitivity Ground setting in areas with minerals In case ground setting cannot be achieved and the device produces deep sounds when iron sound is over level 5 this means the ground being searched includes iron minerals Another case when ground setting cannot be achieved is when the ground is abundant in minerals In these areas if the ground setting cannot be still achieved even if the sensitivity is decreased you should change to Mode 1 or 2 and IRON AUDIO must be in minimum NOTE When there are changes in effects received from the ground or the environ ment sensitivity and ground settings should be repeated 10 SEARCH AND METAL DETECTION Upon completion of the settings you can start exploring by lifting the head by 5 cm from the ground and moving it right to left in a parallel fashion CF77 is a device that operates depending on the motion That s why it should be moving to detect metals As the device operates on the principle of automatic reset it does not detect the metal if you hold it steady on the metal Device provides metals with single sound in GENERAL MODE and 3 different sounds in MODE 1 and 2 2 similar sounds for non ferrous metals and gold a deeper sound for ferrous metals It is recommended that you test the device with different metals to be able to recognize the sounds Thi
Download Pdf Manuals
Related Search