Fluke 709/709H Precision Loop Calibrator
Contents
1. Data Log and Configuration Log Screen Configuration Log Screen Configuration Log Showing Storage Position viii Contents continued Data Log Screen Logging Interval Screen Active Logging SCHOEN eicere tte tren tente cuente rue ERE Ruins ce eae tke see kp dra a YR pace e Battery Replacement 709 709H Users Manual Introduction The Fluke 709 Precision Loop Calibrator and 709H Precision HART Loop Calibrator the Product or the Calibrator can be used for installation calibration and troubleshooting of field transmitters valves and other control system components at process plants Primary functions are source and measure mA signals in the 0 mA to 24 mA range The Product can also produce 24 V dc loop power The 709H includes HART communication functionality and supports a select set of HART universal and common practice commands The Product can be used as a loop calibrator or basic function communicator Product functions include e Current measurement sourcing and a selectable 24 V supply e 30V dc measurement e Valve test capability e Aselectable HART 250 Q loop resistor e Output step and ramp 709 709H Users Manual Product features include Large backlit display Digital selection knob with selectable decade control for easy data entry Interactive menus Communicator mode reads basic device information does2. a PTi12234 yY FT1zz34 EU Uma inh amp aF PY 226 8 inWAC PM m 13 6016 mA PV mcm zn v gzx40 eps Figure 31 Sample Screen This screen shows all of the data retrieved from the data acquisition procedure The tag name is truncated to fit on one line when necessary flashes in the upper right corner to show a live connection 32 Each screen holds a maximum of 6 data points An item can span more than one line when necessary to show the full text If a data item is not supported in the HART device it is marked n a not available Data items that change dynamically in the HART device are updated as often as possible on the screens Turn the selection knob to go from screen to screen Push to go to the Function Select menu Precision Loop Calibrator Write LRV and URV Values Write LRV and URV Values Note For the screens in this section tag names can be truncated to fit on one line if necessary flashes in the upper right corner to show a live connection If the HART write commands are not active these functions are not available and an error message is shown instead of the screen in Figure 32 Taa Hame Write LEV gzx41 eps Figure 32 Write LRV and URV Screen Use the selection knob to choose the necessary function Push the selection knob to choose the highlighted action and go to the corresponding screen These screens are explained in the Write LRV and
3. 709 709H Precision Loop Calibrator Users Manual January 2013 2013 Fluke Corporation All rights reserved Specifications are subject to change without notice All product names are trademarks of their respective companies LIMITED WARRANTY AND LIMITATION OF LIABILITY This Fluke product will be free from defects in material and workmanship for three years from the date of purchase This warranty does not cover fuses disposable batteries or damage from accident neglect misuse alteration contamination or abnormal conditions of operation or handling Resellers are not authorized to extend any other warranty on Fluke s behalf To obtain service during the warranty period contact your nearest Fluke authorized service center to obtain return authorization information then send the product to that Service Center with a description of the problem THIS WARRANTY IS YOUR ONLY REMEDY NO OTHER WARRANTIES SUCH AS FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSED OR IMPLIED FLUKE IS NOT LIABLE FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES ARISING FROM ANY CAUSE OR THEORY Since some states or countries do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages this limitation of liability may not apply to you Fluke Corporation Fluke Europe B V P O Box 9090 P O Box 1186 Everett WA 98206 9090 5602 BD Eindhoven U S A The Netherlands 11 99 Table of Contents
4. attrrefe Urol 1101n eran E T E How to Contact Fluke arcere vit reo e a a r i O AEAEE E eee EEE STA EEROR cfe Eai Standard Equipment rcr oret rre teret tno etat elec chives eroe aste Ea Eo p e Lene Ee TER Eua The ProdUGt NE E TOUR OTI E ra aE aaae A NEEE S Ells Meljen P TT E E E E E The Selection KNOD wessdsscs seca scasscassactucentsoaisadusansosaoaasead ncaasandeaandadeisedasesansapoaddwanpuateauneass Main Oe PE TP EET MMA SOURCO MART TERNI MASIMU ROTEN MA WT cccccccseseecececececeessececeenseaueaseceeeeeseauesseeeeeeeseaueaeeeeeseeseaueaseeeeseeseaaenseeeas mA Measure with 24V Volts Measure cccccccccesessecececcceeneesececeeeceaaeeeeeececeaeeaesseeeeeeeaueaseeeseeeseaueaseeeeeeeeeanenss Calibrator Setup MENU suco tpe eati ti io ip narret nosis setamennstetenduartieaedoct taser Re REDE tates 709 709H Users Manual Auto Ramp Time Auto Step TIME E aaita Step and Ramp Operation Automatic Step and Ramp WAIVE TeS erae LLLI OT LESS HART 250Q Resistor mA Span COMMAS E E E E E E E Auto Shutdown Time HART Write Enables eeina aeaea aaeain ei iaeaea sake su E EES aE HART Device Communication HART COMMECtHONS aeae ar aara E E r a E E In Circuit External Loop Power In Circuit Product Loop Power ssssssssesese enne nnneneernt nnne Across Circuit Communicator Only Communications Setup and Selection g
5. to 100 and back The 100 value is always 20 mA but the 0 value can be 0 mA or 4 mA This depends on how the mA span is set The 25 step size is 5 mA or 4 mA accordingly To use the manual step function 1 Use the Main menu to set the Product to source or simulate current 2 Push to set the output to 0 96 of span Push to set the output to 100 96 of span 4 Push to step the output in 25 96 of span increments from 0 of span to 100 of span and back 18 Automatic Step and Ramp To use the automatic step and automatic ramp functions 1 Usethe Main menu to set the Product to source or simulate current 2 The Product has separate auto ramp and step times Use the menu to set the ramp or step time 3 Push once to continually step the output from 0 96 of span to 100 96 of span and back in increments of 25 of span at the specified interval 4 Push once more to go to auto ramp Push one of the percent keys and twice to turn off the auto step and ramp 6 Push twice to continually ramp the output from 0 96 of span to 100 of span over the specified interval and then back over the specified interval 7 Push one of the percent keys or once more to turn off the auto step and ramp Precision Loop Calibrator Calibrator Setup Menu Valve Test The Valve Test function turns on or off the valve test feature See Figure 13 Valve Test Enable cr D Figure 13 Valve Test Enab
6. 709 709H Users Manual vi List of Figures Figure 1 Standard Equipment sssssssssseseenene nenne nennen nennen nennen nne en nennen ens 2 ButtoliS x neteto citet eeeateton teer tes tis uretecu ton tede tete E cant sak fs tecta ce ovd esere espe ue EEE 3 Mai PEE 4 mA Source Connections esssssesessssesesee eene enne nnn nn nne n nnne nni nsn esse ann se nsns anra n nen 5 mA Simulate Connections oit ratore to e rea ao Ese S Ea Y ER ra To s Fa ava Fav CE LY a Fa Vea a edidere eiiiai Cb v CE ua YS 6 mA Measure Connections cccccccccceaseseececeeececueseeceeeeeceauesseceeeeeaeaaeeeeeeeeseauaaseeeeeesseaneaseees T mA Measure with 24 V Connections 8 Volts Measure Connections ccccsesceccccceccesseeecececeaueaseceeeeeseauensecceeeeseaaeaeeeeeseesuaaeeeeseeseeaa 9 Setup Menu Screen 1 ce enintra aieas pedeo aaae ee iaaiiai a pidea ea a Erain 10 Setup Menu Screen 2 cccccccccceccceccce cece eeceeeaneeceeeeeeeesanaeceseeeceeseaaaaeeceeeseeeeaaeaeaeeeseeeeeeeaeeeees 11 Auto Ramp Time Screen ieina AEAEE DDR riaria 12 Auto Ramp Step Time Screen sssssssssseeeeee eene nenne enne en nennen 13 Valve Test Enable ScFe8r iic re cobenscecvadased esctins sas shes sand ceseedee c Ge beue Fue eda Eua 14 HART Resistor Enable Screen ccccccccccccsseseseecececeaecececeseaueseececeeseauesseceeeeeseaaeeeeeeeeeeaeaas 15 mA Span Selection creen ecco itcr
7. Write URV sections Push to go to the Function Select menu Write LRV The Product warns you to change the loop to MANUAL before you proceed Push the selection knob to proceed Push to go to the Write LRV and Write URV menu The present LRV value and units are shown See Figure 33 Tag Hame 2 Hrite LEV degrees F 300 5 Press hold to Write gzx42 eps Figure 33 Write LRV Screen 1 Push the selection knob to move the decade cursor 2 Turn the selection knob to increment or decrement the value in steps indicated by the selected decade 3 Push and hold the knob to send the new value to the HART device An error is shown if the HART device rejects the value 33 709 709H Users Manual 4 Push to go to the Function Select menu A reminder to change the loop to AUTOMATIC is shown first Write URV The Product warns you to change the loop to MANUAL before you proceed Push the selection knob to proceed Push to go to the LRV and URV menu The present URV value and units are shown See Figure 34 C Tag Hame v Write URW degrees F 300 50 Press amp hold to Write gzx43 eps Figure 34 Write URV Screen 1 Push the selection knob to move the decade cursor 2 Turn the selection knob to increment or decrement the value in steps indicated by the selected decade 34 3 Push and hold the knob to send the new value to the HART device remaining on this displa
8. Send Figure 38 Set Fixed mA Output Screen gzx47 eps 37 709 709H Users Manual PV Zero A warning to change the loop to MANUAL before you proceed is shown Push the selection knob to proceed Push to go to the Trim Set and Zero menus The screen shown in Figure 39 prompts you to set the PV process input signal to zero and then monitors the result with the Product measurement The measurement is updated once a second When the operation mode is Communicator Only the mA measurement is not available and the message mA not available in Comm Only mode is shown instead C b 4 065mA se knob to zero Fr Imi gzx48 eps Figure 39 PV Zero Screen 38 Push the selection knob to zero the HART device and stay on this screen to evaluate the result An error is shown if the HART device rejects the zero command Push to go to the Trim Set and Zero menu A prompt to restore the PV process input signal to normal operation configuration and change the loop to AUTOMATIC is shown first Precision Loop Calibrator Device Diagnostic Device Diagnostic Note For the screens in this section tag names can be truncated to fit on one line if necessary V flashes in the upper right corner to show a live connection If the HART write commands are not active this function is not available and an error message is shown A warning to change the loop to MANUAL before you proceed is shown
9. The write enable selection is saved only when the correct password is given Otherwise an error message is shown Push the selection knob to move the decade cursor Turn the selection knob to adjust the value in steps indicated by the decade selected Push and hold the selection knob to save the write enable setting Push to restore the previous HART enable selection and go to the Main Screen Password ic Press S hold to Save gzx31 eps Figure 19 Password Screen Precision Loop Calibrator HART Device Communication HART Device Communication The HART functions are only available in the 709H Auto shutdown is disabled when the HART menus are used Auto shutdown is restored to its previous state when you exit the HART menus Note Loop current trim is supported for transmitter devices but is not supported for actuator devices These functions can be disabled with the HART Write Enable selection on the Product e write LRV write URV device diagnostic tiim4 mA trim 20 mA e fixed output PV zero functions can be disabled with the HART Write Enable selection on the Calibrator Setup menu See the Calibrator Setup Menu section of this manual If these functions are necessary they must be enabled before you enter the HART menus HART Connections See the subsequent sections for HART connections 23 709 709H Users Manual In Circuit External Loop Power HART resistor is enabled If t
10. diagnostic tests and can be used to trim the calibration of most HART enabled transmitters Note All figures in this Manual show the 709H How to Contact Fluke To contact Fluke call one of the following telephone numbers e Technical Support USA 1 800 44 FLUKE 1 800 443 5853 e Calibration Repair USA 1 888 99 FLUKE 1 888 993 5853 e Canada 1 800 36 FLUKE 1 800 363 5853 e Europe 31 402 675 200 e Japan 81 3 6714 3114 e Singapore 65 6799 5566 e Anywhere in the world 1 425 446 5500 Or visit Fluke s website at www fluke com To register your product visit http register fluke com To view print or download the latest manual supplement visit http us fluke com usen support manuals Precision Loop Calibrator Safety Information Safety Information A Warning identifies conditions and procedures that are dangerous to the user A Caution identifies conditions and procedures that can cause damage to the Product or the equipment under test AA Warning To prevent possible electrical shock fire or personal injury e Read all safety Information before you use the Product e Use the Product only as specified or the protection supplied by the Product can be compromised e Examine the case before you use the Product Look for cracks or missing plastic Carefully look at the insulation around the terminals e Do not use test leads if they are damaged Examine the test leads for damaged i
11. iii brine ns ie aE ta sp Denis FE Coen eR eases aaa vii 709 709H Users Manual 16 17 18 19 20 21 22 23 24 25 26 2T 28 29 30 31 32 33 34 35 36 3T 38 39 40 41 42 43 44 Contrast Adjustment Screen Auto Shutdown Screen ssssss Hart Write Enable Screen Password Screen sssseseeeeee In Circuit External Loop Power Connections In Circuit 709H Loop Power Across Circuit Communicator Only Connections HART Comm Menu Screen Mode Selection Screen ssss 2500 Resistor Screen Polling Screen ene Tag Selection Screen ssss Acquiring Data Screen sesessss Disconnect from Loop Screen Function Select Menu ssssse Sample Screen esee Write LRV and URV Screen Write LRV Screen ssssssssssss Write URV Screen sssssssssss Trim Set and Zero Screen Trim 4 mA Screen sssssssssss Trim 20 mA Screen sssssssssss Set Fixed mA Output Screen PV Zero Screen ssssssssssseee Self Test Screen sssssssussss Self Test Results Screen
12. knob to highlight and select the correct function Push to go to the Log Select menu SAVE operation e lfthe position is empty save the present device configuration data into the storage position e fthe position is in use confirm that the existing data is to be replaced with the present tag data before you save it into the storage position RECALL operation e Ifthe position is empty an error message is shown e If the position is in use the data is shown in a sequence of screens identical to the Device Data Screen ERASE operation e lfthe position is empty an error message is shown e Ifthe position is in use confirm that the existing data is to be permanently deleted before doing so 41 709 709H Users Manual SEND operation e Ifthe position is empty an error message is shown e Ifthe position is in use send the data to the RS232 port in a report format Data Log Process data can be stored for a single tag for later upload to a PC with the 709H TRACK Windows Software See the Configuration Log section of this manual for more Data can be logged in multiple sessions but all sessions must be from the same HART device as determined by the long tag name A different logging interval can be selected for each session Each data sample has the Product measurement device mA and all four process variables There are 9810 records available Each data sample uses one record Each session uses two r
13. of this external power supply This function can test a loop manual with the transmitter removed e 2500 is shown in the lower right corner when Figure 5 shows the mA Simulate home screen and typical the HART resistor has been enabled on the connections for this mode setup menu To use mA Simulate 1 Select mA Simulate from the Main menu Power Supply 30 V dc Max 2 Push the selection knob to move the decade cursor 3 Turn the selection knob to increment or decrement the output in steps indicated by the selected decade 4 Push J z or to set the output to preset 4 mA 20 mA values Input Device 5 Push to select and stop these advanced modes When automatic step or ramp is active one of the subsequent icons is shown in the lower left corner e Automatic step iT e Automatic ramp A 6 Push to go to the Main menu 7 Push again to go to the mA Simulate home Screen gzx004 eps Figure 5 mA Simulate Connections 12 Precision Loop Calibrator The Product mA Measure In the mA Measure mode the Product shows the loop current measurement This mode is without 24 V Figure 6 shows the mA Measure home screen and typical connections for this mode To use mA Measure Select mA Measure from the Main menu Once selected the Product changes to the mA Measure home screen 2500 is shown in the lower right corner when the HART resistor has been enabled on the setup menu 4 mA 20 mA Output De
14. 500 resistor selection defaults to n a not applicable 28 250 2 Resistor The 250Q Resistor function lets you turn the 250 Q resistor on or off Use the selection knob to change the resistor to the highlighted selection and return to the Setup and Selection screen See Figure 25 z586 Resistor OFF ON in gzx34 eps Figure 25 2500 Resistor Screen Precision Loop Calibrator HART Device Communication HART Connect The HART Connect function locates the HART device in the loop Before an operation with a HART device the device must be located on the loop This is done by polling all of the possible device addresses and selecting a device from those addresses that respond to the search If a HART protocol revision 5 or earlier device is found on the loop polling stops at poll address 15 If not found the Product continues to poll address 63 Polling stops after 10 devices are found on the loop If multiple devices are found on the loop a tag list is shown From the list select the correct device If only one device is found on the loop it becomes the selected device by default When a selected device is found all relevant data is read from the device and the operations described in the Function Select Menu and Device Setup and Data sections of this manual become available Polling Loop The Polling Loop function searches the loop for HART devices This function starts immediately The screen c
15. A prompt to change the loop to AUTOMATIC is shown first An error is shown if the device rejects the mode change command Precision Loop Calibrator Trim Set and Zero Menu Set Fixed mA Output If the operation mode is Communicator Only this function is not available and an error message is shown A warning to change the loop to MANUAL before you proceed is shown Push the selection knob to proceed 1 Push to go to the Trim Set and Zero menu As the HART device is changed to fixed output mode an information screen is shown An error is shown if the HART device rejects the mode change command When the mode change is successful the screen in Figure 38 is shown cr v 4 865 m Select Fixed output This screen is used to set a fixed output and monitor the result with the Product measurement The measurement is updated once a second The range of values that can be set is 3 0 mA to 21 0 mA Use the selection knob to select and increment or decrement the value in steps shown by the selected decade Push and hold the selection knob to send the new value to the HART device and stay on this screen An error is shown if the HART device rejects the value Push to change the HART device to normal output mode and go to the Trim Set and Zero menu A warning to change the loop to AUTOMATIC is shown first An error is shown if the device rejects the mode change command 4 000 m Fress amp hold to
16. H Quick Reference Guide 709 709H Safety Information Precision Loop Calibrator Standard Equipment gzx002 eps Figure 1 Standard Equipment 709 709H Users Manual The Product The subsequent sections are about the features and functions of the Product The Buttons Figure 2 and Table 3 show the location and brief descriptions of the Product buttons gzx001 eps Figure 2 Buttons Table 3 Buttons Function Push to enable step or ramp Push to turn on or turn off the backlight Push to turn on and turn off the Product Uu T c OBIE Push to set the output to 20 mA when in mA Source or mA Simulate modes In Measurement mode the button does not set the output current Push to step the output up or down by 25 increments 4 8 12 16 20 mA Push to set the output to 4 mA when in mA Source or mA Simulate mode In Measurement mode the button does not set the output current Push to enter the Main menu Push a second time to exit the Main menu See the Main Menu section Precision Loop Calibrator The Product The Selection Knob The selection knob lets you select and control necessary functions and navigate through the Product menus Turn the selection knob to highlight a menu item or adjust a value When the necessary selection is highlighted push the selection knob to do the selected action or push and hold to s
17. Push the selection knob to proceed Push to go to the Function Select menu Push the selection knob to select and start the self test See Figure 40 Tag Hame v un iT IF Test Press knob to test gzx49 eps Figure 40 Self Test Screen As the self test is done the bottom line of the screen changes to Testing and a string of dots extends once per second to show the operation progress At the end of the self test the screen in Figure 41 is shown It shows No errors or the first error is reported Tag Hame gzx50 eps Figure 41 Self Test Results Screen The lower left corner shows VW when additional errors follow the present error A is shown when additional errors precede the present error V and A show when additional errors follow and precede the present error 39 709 709H Users Manual Turn the selection knob to step between errors 1 Push to go to the Function Select menu A reminder to change the loop to AUTOMATIC is shown first Configuration Log and Data Log Configuration Log and Data Log are only available when connected to a HART device Use the selection knob to choose either the Configuration Log or Data Log See Figure 42 Tao Hame Y Configuration Log lata Log lt d gzx51 eps Figure 42 Data Log and Configuration Log Screen 40 Configuration Log Configuration data for a maximum of 20 tags can be stored for later recall
18. SE operation Logging e e If there is no logged data an error message is Interval 38 seconds shown Elapsed 2 15 25 e Otherwise confirm that the present data is to be Records used zra permanently erased before doing so Records Free di Select the logging interval See Figure 46 02H e 208 mn V me Bcl mh Select Interval L2 sitios p serena Figure 47 Active Logging Screen T seconds Push to stop logging and go to the first data log S seconds Screen 1B seconds 3B seconds BE seconds gzx55 eps Figure 46 Logging Interval Screen 43 709 709H Users Manual The data items shown are 44 The top line indicates is logging is in progress Logging or is stopped Stopped Logging stops automatically when storage is full or before the Product is turned off when the battery reaches its low voltage automatic shutoff limit of 5 6 V Interval is the item previously selected Elapsed is the time since the log was started updated each time a new sample is saved Records used is the total number used to date for all sessions updated each time a new sample is saved Records free is the total number that remain unused updated each time a new sample is saved 709H is the present measurement updated as often as possible PV mA is the last HART device measurement updated as often as possible Maintenance AAWarning For safe operation and maintenance of the Product Repair the Product before use if the ba
19. The configuration data saved is the same as that shown on the Device Data screen The initial Configuration Log screen spans more than one screen and shows a list of the tags held in storage If a storage position is not used the tag name area shows empty See Figure 43 Configuration Loa 5 Tag 1 on two lines 2 empty lf Tag 3 ii Tag 4 VA gzx52 eps Figure 43 Configuration Log Screen After a storage position is selected data can be saved or recalled from it It can be erased or sent to the USB port The data can also be uploaded to a PC with the 709H TRACK Windows Software Precision Loop Calibrator Device Diagnostic It is recommended that you use a Lemo to USB cable with 709H TRACK Software It has a USB Serial adapter that uses an FTDI chipset This combination gives consistent and reliable communication between the Product and PC The USB Drivers are included on the 709H TRACK Software CD Use the selection knob to highlight and select the correct storage location Push to go to the Log Select menu When a storage position is selected the menu in Figure 44 is shown Select the necessary action Lo mb o Tt om GE du SIMI Ch it oi Tm Io Ea XQ d gzx53 eps Figure 44 Configuration Log Showing Storage Position The number and contents of the storage position are shown at the top The tag number is empty if the storage position is empty Use the selection
20. an Selection Screen Precision Loop Calibrator Calibrator Setup Menu Contrast The Contrast function adjusts the display contrast Turn the selection knob to adjust the contrast The range is shown by the bar graph Higher contrast is shown by a longer bar The sample normal and reverse video selections let you evaluate both text modes See Figure 16 Contrast TT TTT Sample normal video gzx28 eps Figure 16 Contrast Adjustment Screen Auto Shutdown Time The Auto Shutdown Time function sets or turns off the time before the Product automatically shuts itself down if the keypad is not used The value can be set to Disabled or from 1 minute to 30 minutes See Figure 17 Auto Shutdown Time 10 Min gzx29 eps Figure 17 Auto Shutdown Screen 21 709 709H Users Manual HART Write Enable HART Write Enable is the last function in the Calibrator Setup Menu See Figure 18 G D HART Write Enable Figure 18 Hart Write Enable Screen gzx30 eps This function is available only on the 709H It protects the Write LRV Write URV Device Diagnostic Trim 4mA Trim 20mA Set Fixed Output and PV Zero functions The default setting is ON but it may be turned off to protect the Product against unauthorized use 22 Before the setting is changed a password is required The password is set to 617 at the factory The range of values that can be set is 000 to 999 See Figure 19
21. ave any changes that have been made Push to go to the main screen with no action In the output modes mA Source mA Simulate e Push the selection knob to move the display cursor to the next digit e Turn the selection knob to increment or decrement the output in steps shown by the selected decade e Push J z or to set the output to preset values e Push A to select and stop these advanced modes Main Menu Push to show the Main menu choose the primary operation mode of the Product access the Product setup menu or to use HART mode See Figure 3 gzx20 eps Figure 3 Main Menu The first five items shown on the Main menu change the Product operation mode accordingly and once selected change the Product menu to a home screen for the selected function The operation modes are explained in the subsequent sections of this manual For the last two items of the Main menu see The Calibrator Setup Menu and Hart Comm Menu sections Note The HART menu items only apply to the 709H 709 709H Users Manual 10 Note Some menus have multiple screens When this is the case the lower left corner of the menu shows W when additional screens follow the current screen amp is shown when additional screens precede the current screen Both icons are shown when additional screens follow and precede the present screen mA Source In the mA Source mode the Product outputs a signal f
22. cifications Specifications Ranges MA e 0 mA to 24 mA NOMS H 0 V dc to 30 V dc Resolution mA Ranges ssssssssee 1 uA Voltage Range eoe 1 mV ACCURACY 5 5 5202 EQ 0 01 2 LSD all ranges 23 C 5 C Stability eae eea roe 20 ppm of F S C from 10 C to 18 C and 28 C to 55 C Operating Temp Range 10 C to 50 C 14 F to 122 F Storage Temp Range 20 C to 60 C 4 0 F to 140 F AUG 2 rrr tremens 3000 meters Ingress Protection Rating IEC 60529 IP40 Humidity Range 10 96 to 95 non condensing DIS AY C 128 x 64 pixels LCD Graphic with backlight 8 6 mm high digits POW E tiroteo a Six AAA alkaline batteries Battery Life Alkaline Batteries 240 hours continuous use measure mode Loop Compliance Voltage 24 V dc 20 mA Loop Drive Capability 1200 Q without HART resistor 950 Q with HART resistor 49 709 709H Users Manual Electromagnetic Environment IEC 61326 1 portable equipment Dimensions LXWXD 152 x 93 x 44 mm 6 0 x 3 7 x 1 7 in Welght rre 0 3 kg 9 5 oz 50
23. ct Category With reference to the information See manual equipment types in the WEEE Directive Annex I this product is classed as category 9 Monitoring and Control Instrumentation product Do not dispose of this product as unsorted municipal waste Go to Fluke s website for recycling information Hazardous voltage Risk of electrical shock Examined and licensed by TUV Product Services Precision Loop Calibrator Symbols Table 1 Symbols cont Battery Double insulated Measurement Category II is applicable to test and measuring Measurement Category III is applicable to test and circuits connected directly to CAT III measuring circuits connected to the distribution part of utilization points of low voltage the building s low voltage MAINS installation mains installation Measurement Category IV is applicable to test and measuring circuits connected at the source of the CAT IV AED building s low voltage MAINS installation The CAT ratings apply to the handheld accessories only The Product is rated to 30 V maximum 709 709H Users Manual Standard Equipment Items included with the Product are listed in Table 2 and shown in Figure 1 Table 2 Standard Equipment m o Pee Tasses OOOO 75X 8014 stackable lead set 709H TP220 4201 test probes 709H AC280 5001 Suregrip hook clips 709H 2 Soft Case Six AAA batteries installed 709 709H Product Manual CD ROM Not Shown 709 709
24. ecords for overhead data that is common to all of the data samples in that session There can be from 1 to 99 sessions The total number of data samples that can be logged is 9810 less 2 times the number of sessions started and stopped See Figure 45 42 ot tu i on tuo lines START ERASE Battery 6 Y gzx54 eps Figure 45 Data Log Screen The number of free records is shown on the first line If data has already been logged the tag number is shown below it The present battery voltage is shown at the bottom so that you can tell if the batteries should be changed before a log session starts The log is stopped before the Product is turned off when the battery reaches its low voltage automatic shutoff limit of 5 6 V e Use the selection knob to highlight and select the correct function e Push the knob to do the operation Push to return to the Log Select menu Precision Loop Calibrator Device Diagnostic START operation Turn the selection knob to move the highlight and select e f no free records or free sessions remain or the present HART device does not match the HART the necessary interval Push the selection knob to start logging at that interval Push to go to the first data log Screen device already logged an error message is shown e Otherwise proceed to interval selection described below While logging the screen in Figure 47 is shown to monitor progress ERA
25. hanges to show the string of dots that is extended once per second to as the operation progresses See Figure 26 Polling Loop Fress knob to skip remainder gzx35 eps Figure 26 Polling Screen The number of devices found on the loop during polling is shown The selection knob can be pushed to stop polling early if itis known that all of the devices on the loop have been found Push to stop polling disconnect from HART mode and go to the function home screen An error is shown if no device is found If multiple devices are found a list of tags is shown Use the list of tags to select the necessary device If only one device is found the tag selection step is skipped 29 709 709H Users Manual Tag Selection The tag selection screen lists all of the long tag names found during polling Tag names can span two lines if necessary to show all of the text If the long tag name is not available or it is blank a short tag name is used If the short tag name is blank the text Poll address x is used Use the selection knob to go to the necessary tag See Figure 27 Long Tag i on tuo lines Long Tag 2 Long Tag 3 Long Tag 4 aon two lines vA gzx36 eps Figure 27 Tag Selection Screen 30 Acquiring Data The Acquiring Data screen is shown while the Product acquires all of the configuration data from the device The string of dots extends once per second to show the operation pr
26. he Product measurement The measurement is updated once a second 1 Push the selection knob to trim the HART device Stay on this screen to evaluate the result An error is shown if the HART device rejects the trim command 2 Push to change the HART device to normal output mode and go to the Trim Set and Zero menu A warning to change the loop to AUTOMATIC is shown first An error is shown if the device rejects the mode change command 35 709 709H Users Manual Trim 20 mA If the operation mode is Communicator Only this function is not available and an error message is shown A warning to change the loop to MANUAL before you proceed is shown Push the selection knob to proceed Push to go to the Trim Set and Zero menu While the HART device is changed to fixed output mode an error is shown if the HART device rejects the mode change command When the mode change is successful the screen in Figure 37 is shown Tag Hame E Trim D A at 28 mA 19 965mA Press knob to trim gzx46 eps Figure 37 Trim 20 mA Screen 36 As the output to settles at 20 mA the screen shows the Product measurement The measurement is updated once a second 1 Push the selection knob to trim the HART device Stay on this screen to evaluate the result An error is shown if the HART device rejects the trim command 2 Push to change the HART device to normal output mode and go to the Trim Set and Zero menu
27. he loop already has 250 Q In mA Measure mode the Product is in circuit and loop do not enable the HART resistor power is supplied externally In Figure 20 the 250 Q B B2 4 000mA gzx008 eps Figure 20 In Circuit External Loop Power Connections 24 Precision Loop Calibrator HART Device Communication In Circuit Product Loop Power the 250 Q HART resistor is enabled If the loop already In mA Measure with 24V mode the Product is in circuit has 290 0 donor erable Ne HAST resistor and loop power is supplied by the Product In Figure 21 gzx009 eps Figure 21 In Circuit 709H Loop Power 25 709 709H Users Manual when in Communicator Only mode there must be 250 Q Across Circuit Communicator Only resistance present in the loop In Communicator Only mode the Product is across the circuit and loop power is supplied externally In Figure 22 4 mA to 20 mA RL 2 250 Q gzx010 eps Figure 22 Across Circuit Communicator Only Connections 26 Precision Loop Calibrator HART Device Communication Communications Setup and Selection For all Main screen operation modes except mA Measure with 24V or Volts Measure the operation mode is set to mA Measure when you enter the HART Comm Menu The operation mode remains the same as the main screen when it is Measure with 24V If Volts Measure was selected from the Main menu the menu defau
28. le Screen gzx25 eps The valve test verifies correct operation of valves In valve test the output can be stepped to these values 3 8 mA 4 0 mA 4 2 mA 8 0 mA 12 0 mA 16 0 mA 19 8 mA 20 0 mA 20 2 mA The valve test mA values are not affected by the mA span setting 1 Use the Main menu to set the Product to source or simulate current If valve test is not enabled use the menu to enable it Push fA or to step the output to verify the proper valve operation Use the menu to disable valve test when done 19 709 709H Users Manual HART 2502 Resistor The HART 250Q Resistor Enable function turns on and turns off the HART resistor See the HART Resistor section of this manual See Figure 14 gt HART Resistor Enable OFF ON S p gzx26 eps Figure 14 HART Resistor Enable Screen The Product can insert a 250 O resistor in series with the power supply in order to use a HART communicator The HART resistor is enabled through the menu To get to the second Calibrator Setup Screen highlight Other Parameters and push the selection knob 20 mA Span mA Span is the first item on the second Calibrator Setup Menu The mA Span function sets the step interval for the mA Auto Step feature The value can be set from 5 seconds to 300 seconds See the Step and Ramp Operation section of this manual See Figure 15 ma Span Selection gzx27 eps Figure 15 mA Sp
29. lts to communicator mode only and the 250 Q resistor selection shows n a The 250 O resistor selection cannot be edited in communicator mode The mode and resistor will change from the last selections made in the HART Comm Menu when you exit the menu The mode and 250 Q resistor settings must correspond to how the test leads are connected before you connect See Figure 23 HABET Comm fer 4 123mA Mode mhz4 v Sot Resistor UH CONNECT gzx32 eps Figure 23 HART Comm Menu Screen Select a function from the menu and push the selection knob to do the function Push to disconnect from HART mode and go to the function home screen without action An error is shown and no action is taken if the measured input is out of range OL or OL 2500 Resistor and HART CONNECT functions are described in subsequent sections 27 709 709H Users Manual Mode The Mode function from the HART Comm Menu lets you select what mode to work in See Figure 24 A hode mm Measure mA Measure with z4 Communicator Only gzx33 eps Figure 24 Mode Selection Screen Use the selection knob to choose the necessary mode mA Measure The Product is in circuit and loop power is supplied externally mA Measure with 24V The Product is in circuit and the loop power is supplied by the Product Communicator Only The Product is across the circuit and the loop power is supplied externally The 2
30. nsulation and measure a known voltage e Do not use and disable the Product if it is damaged e Do not use the Product around explosive gas vapor or in damp or wet environments Do not touch voltages gt 30 V ac rms 42 V ac peak or 60 V dc Do not apply more than the rated voltage between the terminals or between each terminal and earth ground Do not connect directly to mains Do not exceed the Measurement Category CAT rating of the lowest rated individual component of a Product probe or accessory Keep fingers behind the finger guards on the probes Remove all probes test leads and accessories before the battery door is opened Remove the batteries if the Product is not used for an extended period of time or if stored in temperatures above 50 C If the batteries are not removed battery leakage can damage the Product Replace the batteries when the low battery indicator shows to prevent incorrect measurements The battery door must be closed and locked before you operate the Product 709 709H Users Manual Symbols Symbols used on the Product and in this manual are explained in Table 1 Table 1 Symbols sme ems ome em EET TNI CNET TT Tc NN This product complies with the WEEE Directive 2002 96 EC marking requirements The affixed label indicates that you must not discard this electrical electronic product in domestic household Risk of danger Important waste Produ
31. nu Screen 1 gzx21 eps ma Span Contrazt Auto Shutdown Time HART Write Enable Figure 10 Setup Menu Screen 2 Note The HART Write Enable menu item only is shown on the 709H gzx22 eps Precision Loop Calibrator Calibrator Setup Menu Auto Ramp Time The Auto Ramp Time function sets the full scale ramp time for the mA ramp feature The value can be set from 5 seconds to 300 seconds Push the selection knob to move the decade cursor Turn the selection knob to adjust the value in steps indicated by the decade selected See Figure 11 Auto Eamp Time 10 Sec Fress amp hold to Save gzx23 eps Figure 11 Auto Ramp Time Screen Auto Step Time The Auto Step Time function sets the step interval time for the mA Auto Step feature The value can be set from 5 seconds to 300 seconds Push the selection knob to move the decade cursor Turn the selection knob to adjust the value in steps indicated by the decade selected See Figure 12 Auto Step Time 10 Sec Press hold to Save gzx24 eps Figure 12 Auto Ramp Step Time Screen 17 709 709H Users Manual Step and Ramp Operation For step and ramp operation the percent keys can be used to set the milliamp output to 0 of span 100 of span or step the output by 25 of span Hands free operation is possible with TA Set the Product to automatically and continuously step or ramp the milliamp output from 0
32. ogress flashes in the upper right corner to show a live HART connection The screen in Figure 28 shows the name of the tag that is accessed v Acquiring Data Tag Hame gzx37 eps Figure 28 Acquiring Data Screen Push to stop data acquisition disconnect from HART mode and go to the function home screen When data acquisition is complete the Function Select Menu is shown Precision Loop Calibrator HART Device Communication Disconnect from Loop The Disconnect from Loop screen is shown before the Product returns to the function home screen so the Product can be disconnected from the Loop See Figure 29 Disconnect Press Menu Exit to exit HART mode L SSS d Figure 29 Disconnect from Loop Screen gzx38 eps Function Select Menu The Function Select menu is shown in Figure 30 U Tag Hame d r1 tu ct hi eroe Imi ua m E in p zu LE r Ed cu Ii bu ui mo t hi un a ua gzx39 eps Figure 30 Function Select Menu The tag name is truncated to fit on one line when necessary flashes in the upper right corner to show a live connection Use the selection knob to choose the necessary action Push to disconnect from HART mode and go to the function main screen 31 709 709H Users Manual Device Setup and Data The Device Setup and Data screen spans 11 screens with the format shown in Figure 31
33. ollar Meo T brasce TAG SEC CU ON E tient AGC QUINING Data cocse c Disconnect from LOOP e Function Select Menu sssssssseeene enn enne nn eene emen nre Device Setup and Data ccce eeice eiieeii nennen Write LRV and URV Values Write LRV Write URV Trim Set and Zero Menu Contents continued TAMA MA e Up ers Id ceungsUE E Ac Device Di gNoStG esise Configuration Log and Data Log ro jio diez ire goo TN Data Oi C E MAINTENANCE c Clean the pc Battery Replacemerit 2 eee Lee RU EP eta iere SER Ls Den ANni User Replaceable Parts cccccccecceceeeeeeeceeeeeeeeeeeeeceeeaeeeeeeesececaeeeeeeeeesenceeeeeeeeeneeeeeea jeu ii iii 709 709H Users Manual Table Bow List of Tables Title Page Mose I A Standard Equipment sete i aiiai tesdees tenebo aaie ai de eee ecce nte abra 6 SIDE ERE E E E E E E 8 User Replaceable Parts tret testi tniad austeni aiiis tior saiae tiiis
34. ore information about these items and their prices contact a Fluke representative See the Contact Fluke section Table 4 User Replaceable Parts Item Fluke Part Number Fluke 709 2005 Knob 4282155 Fluke 709 2001 Case Top 4252536 Fluke 709 2002 Case Bottom 4252549 Fluke 709 2003 Battery Door 4257167 Fluke 709 2004 Connector Panel 4257171 Fluke 709 2006 Holster Fluke 709 4241437 Fluke 709H 2006 Holster Fluke 709H 4241443 Fluke 709 2007 Bail Fluke709 709H 4241455 Fluke 709 8003 Keypad Fluke 709 709H 4252551 TL75 4201 TEST LEADS 855742 47 709 709H Users Manual Table User Replaceable Parts cont Item Fluke Part Number AC280 5001 01 175 277 011 AC280 SUREGRIP HOOK CLIP BLACK BULK 2063165 AC280 5001 175 277 013 SUREGRIP HOOK CLIP RED BULK 1613782 AC72 1 01 ALLIGATOR CLIP 30V 2MM JACK RED BOOT 4209063 AC72 1 02 ALLIGATOR CLIP 30V 2MM JACK BLACK BOOT 4209074 TP220 4201 TEST PROBES RED 2047206 TP220 4201 01 TEST PROBES BLACK 2063129 FLUKE 754 8016 ALLIGATOR CLIP SET EXTENDED TOOTH 3765923 FLUKE 75X 8014 CABLE ASSEMBLY STACKABLE LEAD SET 3669716 CD Users Manual Fluke 709 709H 4240654 Safety Sheet Fluke 709 709H 4240668 Quick Reference Guide Fluke 709 709H 4255201 709H TRACK Datalogging Software amp Cable 4281225 SOFTCASE POLYESTER BLK YEL 10 00 7 50 3 00 C115 2643273 48 Precision Loop Calibrator Spe
35. rom 0 mA to 24 mA into a load of up to 1000 Q 750 Q if the internal HART resistor is switched on Figure 4 shows the mA Source home screen and typical connections for this mode Precision Loop Calibrator The Product To use mA Source 1 2 3 Select mA Source from the Main menu Push the selection knob to move the decade cursor Turn the selection knob to increment or decrement the output in steps indicated by the selected decade Push J amp z or to set the output to preset values Push to select and stop these advanced modes When automatic step or ramp is active one of the subsequent icons is shown in the lower left corner Automatic step iT Automatic ramp A Push to go to the Main menu Push again to go to the mA Source home screen Valve Test is shown in the lower center when the valve test function has been enabled on the Setup menu See the Valve Test section of this manual 2500 is shown in the lower right corner when the HART resistor has been enabled on the setup menu 4 mA to 20 mA Input Device Recorder Indicator etc 4 mA to 20 mA gzx003 eps Figure 4 mA Source Connections 11 709 709H Users Manual mA Simulate e Valve Test is shown in the lower center when In the mA Simulate mode the Product functions like a the valve test function has been enabled on the 2 wire transmitter and controls the loop current from an Setup menu See the Valve Test section
36. ttery leaks Be sure that the battery polarity is correct to prevent battery leakage Remove the input signals before you clean the Product Use only specified replacement parts Have an approved technician repair the Product Precision Loop Calibrator Maintenance Clean the Product Clean the Product and pressure modules with a soft cloth dampened with water or water and mild soap ACaution To prevent possible damage to the Product e Do not use solvents or abrasive cleansers e Do not allow water into the case Fuse The Product is protected from overcurrent condition by an internal self resetting fuse The fuse will automatically reset within a few seconds The fuse cannot be repaired manually 45 709 709H Users Manual Battery Replacement Replace the batteries when the battery indicator is shown on the display To replace the batteries 1 Remove the holster 2 Turn the Product over so the display is face down 3 With a flat head screwdriver remove the battery door screws Remove the batteries Replace the old batteries Note the correct polarity as the new batteries are installed 6 Attach the battery door Tighten the two battery door screws 8 Put the Product back into the holster See Figure 48 46 Figure 48 Battery Replacement gzx011 eps Precision Loop Calibrator User Replaceable Parts User Replaceable Parts User replaceable parts are shown in Table 4 For m
37. vice 4 mA to 20 mA gzx005 eps Figure 6 mA Measure Connections 13 709 709H Users Manual mA Measure with 24V Figure 7 shows the home screen and typical connections In the mA Measure with 24V mode the Product outputs for this mode 24 V dc as it shows the loop current The mode can power a transmitter without a separate power supply gzx006 eps Figure 7 mA Measure with 24 V Connections 14 Precision Loop Calibrator The Product To use mA Measure with 24 V 1 Select mA Measure with 24 V from the Main menu Once selected the Product changes to the mA Measure with 24 V home screen 2500 is shown in the lower right corner when the HART resistor has been enabled on the setup menu Volts Measure In the Volts Measure mode the Product shows the loop voltage Figure 8 shows the Volts Measure home screen and typical connections for this mode To use the Volts Measure mode Select Volts Measure from the Main menu Once selected the Product changes to the Volts Measure home screen Voltage Output Device gzx007 eps Figure 8 Volts Measure Connections 15 709 709H Users Manual Calibrator Setup Menu The Calibrator Setup Menu has two screens To go to the second screen select Other Parameters from the first screen Screen 1 is shown in Figure 9 and screen 2 is shown in Figure 10 Fa Auto Eamp Time 16 Figure 9 Setup Me
38. y An error is shown if the HART device rejects the value 4 Push to go to the LRV and URV menu A prompt to change the loop to AUTOMATIC is shown first Trim Set and Zero Menu Note For the screens in this section tag names can be truncated to fit on one line if necessary flashes in the upper right corner to show a live connection If the HART write commands are not enabled these functions are not available and an error message is shown instead of the screen shown in Figure 35 Tag Hame Trim O A at 4 mh Trim L at zB ma Set Fixed mA Dutput Zero gzx44 eps Figure 35 Trim Set and Zero Screen Precision Loop Calibrator Trim Set and Zero Menu Use the selection knob to select and start the necessary action Push to go to the Function Select menu Trim 4 mA If the operation mode is Communicator Only this function is not available and an error message is shown A prompt to change the loop to MANUAL before you proceed is shown Push the selection knob to proceed Push to go to the Trim Set and Zero menu While the HART device is changed to fixed output mode An error is shown if the HART device rejects the mode change command When the mode change is successful the screen in Figure 36 is shown C Y Tag Hame v Trim OA at 4 mA 4 OBSmA Press knob to trim gzx45 eps Figure 36 Trim 4 mA Screen While the output to settles at 4 mA the screen shows t
Download Pdf Manuals
Related Search