Home
Manual ESC for car
Contents
1. www fliermodel com _ll FLIER ESC for 2S to 22S Update ESC Firmware 1 Plugging the USB Linker wires be sure that the USB linker wires driver was installed 2 Running the software click the Flash button after a Download ESC type OK message displays in the text box you can reboot the software the second step must be done if not the firmware types which you need for the ESC can t be recognized 3 Choose the correct port from Select COM Port 4 Choose the firmware which you need the next step is click Down Load File button File read message will appear 5 Disconnect the power of the ESC and BEC 6 Plugging 4pin of the ESC into the 4 pin of USB Linker connect OK PI message will appear 7 If any errors pull out 4pin wires then repeat step 6 still correct message 8 Clicking Write button the ESC will be updated software now 9 Waiting until update to 113 pages errors pages O appear tell you the updated software succeed 10 You can disconnect the 4pin of the ESC from the USB Linker now 89 Flier ESC update Software COM Port Website File Select COM Port coma Close ComPort 45 File OK The File Length is 40088 File read Flier ESC Hardware Ver 1 Bootloader Version 1 2 Connect OK Please press Write buttom to update Write gt FEE Es Flier ESC Update Software Version 2 0 1 www fliermodel com eee
2. wait about 5 seconds a four tone melody can be heard this indicates that a main mode programming sequence is ready 4 And then you will hear 5 groups 5 a short beep then 5 groups gt then 5 groups ppd and then 5groups P gt A 5 5 5 groups J a long beep 5 5 groups gt And these sounds of groups will circulate 5 Each group of 5 sounds stands for a different mode of ESC respectively 6 You can put the throttle stick to the middle position during one group of 5 sounds and then the corresponding mode is saved 7 1 P Forward mode gt Forward Reverse mode then you can exit the setting mode after saving the mode When the mode is saved you can disconnect the ESC to the battery pack Forward Only mode and Forward Reverse mode After gt melody Hear the gt gt 5 put the throttle stick to the middle position the mode is changed from Forward Only mode into Forward amp Reverse mode If you want to change it back please repeat the above procedures and vice versa www fliermodel com 5 FLIER ESC for Car 2S to 22S Enter Programming www fliermodel com 6 Group D F orward Mode or Forward Reverse Mode Parameter Saved and Exit Programmi ng Mode FLIER ESC for 2S to 22S O Timing motor ignition advance function value 1 Hear 5 groups P or P or D D 370222 the abo
3. FLIER ESC for 2S to 22S FLIER ESC for Car 2s to22s User s Manual www fliermodel com Tel 86 0755 27905140 Technic support James fliermodel com Sales Cathy fliermodel com Sale fliermodel com Skype Fliermodel FLIER ESC for Car 2S to 22S ESC for Car Manual Thank you for purchasing our products For the high power of this brushless system failure to use may result in injury yourself and damage of the whole device So we highly recommend you to read carefully and abide by the operating procedures of this manual before the first flight Flier is not responsible for your misuse of this product or any damage including incidental losses or indirect losses you may cause Moreover we have not any responsibility for the modification of our products without authorization We have the right to change the design features functions and operating requirement of our products without any advanced notice Feature 1 Design for car more functions 2 Battery voltage from 2S to 225 for super high voltage version 3 Two way communication while connecting it with computer 4 Firmware can be upgraded by user 5 Simply set function value by Prog Box or by PC via USB link wire 6 Li MH Li Po Ne Cd Ne mH LiFe battery can be use 7 Enables setting the voltage per cell for the point at which the controller s cut off circuitry engages Li MH Li Po from 2 0 3 6V Ne Cd Ne mH 0 4 1 0V LiFe from2 2 2 8V 8 Timing settings m
4. ay be adjusted 0 30 per degree to suit the motor type 9 3 types of throttle curve 10 Automatically detection the throttle range or can be set a fixed value by manual operation 11 Auto cut off the power within 3 seconds if no radio signs 12 ABS brake system www fliermodel com 1 FLIER ESC for 2S to 22S Catalog CONCORREN wem em m o aman m a sews em meme m e Dmm em more em e 4 225 www fliermodel com 2 FLIER ESC for 2S to 22S Function Value 1 Reverse On Off ON means forward and reverse mode Off means forward only mode 2 Timing 0 19 29 39 4 59 6 30 3 Frequency 8KHz 16 KHz 32 KHz 4 Acceleration Soft Medium Hard 5 Accumulator type NiCd NiMh Li Ion Li Pol LiFe 6 NiCd NiMH CUTOFF Min 0 4V 0 5V 0 6V 0 7V 0 8 0 9V 1 0V Min means no cut off 7 Cell Counts Auto 2S 3S 4S 5S 6S 7S 8S 9S 10S 11S 12S 16S 17S 18S 19S 20S 21S 22S 23S 24S 8 LiIo Pol LVC cut off voltage per cell 2 0V 2 1V 2 2V 2 3V 2 4V 2 5V 2 6 2 V 2 8V 2 9 3 0V 3 1V 3 2V 3 3V 3 4 3 5V 3 6V 9 LiFe cut off voltage per cell 2 2 2 3V 2 4V 2 5V 2 6V 2 7 2 8V 10 LVC cut off type Slow Cut off Hard Cut off 11 Throttle curve Logarithmical Linear Exponential 12 ABS brake Off 0 10 20 30 40 50 60 70 80 90 100 13 Power limited forward No limited 75 limited 50 limited 25 olimit
5. ed 14 Power limited reverse No limited 75 limited 50 limited 25 limited 15 FWD to REV Delay time 0 255 0 55 0 55 15 25 35 55 16 Forward point Auto fixed 1 7 5 fixed 1 8 5 fixed 1 9mS fixed 2 0mS 17 Reverse point Auto fixed 1 0mS fixed 1 1mS fixed 1 2mS fixed 1 3mS 18 Timing monitor ON Off ON means when ESC ready and the throttle in neutral the motor will beep different times according to the timing of the motor 19 start power Auto 5 10 15 20 25 30 35 40 45 50 55 60 65 0 5 80 85 90 95 100 Usually the default value auto is ok but if the motor startup www fliermodel com Em FLIER ESC for Car 2S to 22S is too violent or too powerless you can adjust the value you can from 590 begin then increase the start power percent till the motor startup performance is good a Diagram for wire connection 1 Correctly connect ESC to brushless motor receiver and battery pack correctly use the Anti spark wire while connect the ESC to battery pack 2 Electronics are correctly power on for the setting 3 Then you will hear 277 or 227 if you don t hear the first three beeps please check your motor connection The last one beep means the ESC enter to forward mode the last two beeps means the esc enter to forward and reverse mode if you can t hear the last one beep or two beeps but continues beeps please check your connection of the receiver The continues beeps means that
6. fault value will be sent to the esc So the ESC will be the Factory Defaults Value ESC www fliermodel com g FLIER ESC for 2S to 22S Function value setting by PC An excellence in this series ESC is that they can be set function value via PC By a match software designed our company via a USB Linker a ESC can communicate with PC then you can Easily set the ESC function value on PC screen r a 1 qi Flier ESC Computer Linking Software MN TE T le eo COM Ports i CONG 7 i R Instructions Download Prolific USS Driver from the Prolific website Flier ESC Type Your ESC type Car 2 85 Lar 2 025 The firmware version is Ver3 0 Write Value to ESC You can change the configuration now Configure ESC Settings Load Factory Default Values Battery LYC PWM Set Points Motor Pole HELI Cell Count Forward Point TW Lithium Ion Polymer LiPo Auto Slow Cut OF E Automatic NMH 16 kHz 6 10 poles x 32 kHz 12 14 poles LiFe A123 Cells 3 2 v Automatic Throttle Curve Acceleration Timing Monitor Delay Time CAR BOAT PWR Limit CAR BOAT Mode HELI Logarithmical Soft Forward 9 Monitor ON FWD to REV Delay Time OFF Contant RPM 9 Linear Medium 0 25S Exponenbal Hard Monitor OFF OFF X Om Start Power CAR ABS Braking CAR Motor Timing Degrees Rotation AIR Reverse CAR BOAT Start Power Off 0 50 9 0 15 30 Left 9 Reverse ON Auto
7. first function MODE TYPE setting interface automatically Then your esc type can be displayed on the LCD screen lt and buttons make no difference because the ESC type can t be changed 5 Press Forward button to enter the second function item CONTROLLER TYPE The 11 66 22 ESC type which you purchased will be displayed on the LCD screen lt and www fliermodel com 2 f FLIER ESC for Car 2S to 22S buttons make no difference because the ESC type can t be changed 6 You can press Forward button enter desired function item then press lt and button enter desired value You also can press Back button then back to the last function item 7 All setting is done The LCD screen will display Sending Data to ESC if you press Back and Forward buttons It prompt the setting value have sent to the ESC 8 Turn off the power of the esc and connect the power You can inspect whether the function values were wrote in the ESC or not O After setting over turn off the ESC disconnect the Prog Box Setting is done Notes If you need restore Factory Defaults You should disconnect the 4pins wires on the ESC after the prog box reading the esc function value Then connect the box with the 4pin wires from ESC The prog box can automatically restore the Factory Defaults after disconnecting At this time you need press Forward and Back buttons The Factory De
8. ng Software You can see a interface which the above mention Because the Flier ESC is not connected the interface isn t operated now 3 Plug your Flier USB linker into the computer and if the USB linker driver has been installed correctly The com port can be automatically selected the automatic selection usually is right but some computer have too many com port is using An error com port selection is possible in this condition you must select the correct com port which the above mention 4 Connect the 4pin wires of the USB linker to the 4pin wires of the ESC pay attention to the color of the wires must ensure the same color wires connect together or you will possibly damage the ESC If you connect correctly the Flier ESC type will display in the ESC type column If don t display correctly you can pull the 4pin wires and plug again till the display is correct 5 You can see the setting value in the Flier ESC will display the program area So you can easily know the setting value of the ESC at current 6 You can change any setting value from the program area you also can press the load factory default text to load the factory default value 7 After you finish your adjustment Press the top right write button your setting value will write into the ESC 8 Disconnect the 4pin wires 9 Exit the flier ESC computer software 10 Pull out the USB liker Now your ESC has been programmed Programming USB wires
9. no receiver signal to the ESC 4 Pushing the trigger then the motor will start to work A The anti spark wire is built in a bullet connector and a 10 ohms resistor you can separate it into two wires You must connect the end of the wire to the battery negative when you connect the ESC with the battery you can connect the red wire of ESC to the positive pole of battery at first Then connect the anti spark wires well The last step is to connect the black wire of ESC to the battery s negative pole If do so no spark will be generated and this will protect the main bullets connector from spark damage Anti spark wire www fliermodel com 4 FLIER ESC for Car 2S to 22S OPTO Function value setting by transmitter You can set some simple function values via the transmitter but want to set the more function values you have to use prog box or PC via USB link wire This ESC has two different types of main mode one is Forward Only mode Reverse Off and another is Forward amp Reverse mode Reverse On If Reverse Off mode is set the motor will spin forward only And if Reverse On mode is set the motor can spin forward and reverse Function value can be changed follow the step below 1 Move the stick of the transmitter on full throttle position power on the receiver 2 After power on the ESC you can hear gt gt melody this indicates that the motor connection is ok 3 Don t move the stick and
10. the USB to serial converter This is the port that will need to be selected in the Flier ESC Computer Linking Software Make note of it aferen ctrl ditt nui COM por remete Flier ESC Computer Linking Software Installation The installation of Flier ESC Computer Linking Software is as the same as the normal windows software In windows system you run simplify setup file and then install it easily according to the prompt After installation finish you can run the software Only after the Flier USB linker connects the Flier ESC to the computer the software can be operated Flier ESC Computer Linking Software Interface Overview 1 The top left of the interface is Select COM Port ESC type this will be for comport select and the Flier ESC type display 2 The top middle of the interface is a text box it can display some messages of the software progress 3 The middle main area of the interface is the program area You can program the setting value of the ESC here 4 The top right of the interface is a write data button You can press it to write the setting value into the ESC 5 The bottom of interface displays the copyright and company website information www fliermodel com I x FLIER ESC for 2S to 22S How to program the ESC 1 This is very important Disconnect the battery the motor and the receiver I e disconnect all connections FLIER of the ESC 2 Launch the Flier ESC Computer Linki
11. v 10 75 5 20 Other Right v 5 00 10 5 eT Copyright 2011 2013 All Rights Reserved by Flier Electronic Cor Ltd Software version 2 24 WWW n If use firstly you must install the USB Linker driver and the ESC setting software Installation of USB Linker driver The below are the instructions of how to install the driver under Windows XP 1 Firstly plug the USB linker into the USB port on the computer The computer will automatically detect the USB linker and ask for installation of the USB driver The computer screen shows the window Found new hardware wizard Press Next button 2 Please select Install from a list or special position Advanced and press Next button 3 Please select Search for the best driver in these locations and check Include this www fliermodel com 9 FLIER ESC for Car 2S to 22S location in the search In the search dialog specify the location of the USB driver that is located in the CD or driver download folder USB driver 4 The above steps probably need to be repeated If any same prompt appear please repeat the installation steps carefully until the installation process is complete 5 Open Windows Device Manager Control panel C system C device manager 6 Find Ports COM amp LPT in the list and click the sign to its left 7 Find the line that reads Prolific USB to Serial Comm Port COMX The x value is the COM port number that was assigned to
12. ve circulation put the throttle stick to the middle position 2 Timing mode 1 5 groups O 7 recommended for 2 poles and common motors 3 Timing mode 2 5 groups 8 15 recommended for 4 poles motors 4 Timing mode 3 5 groups gt gt 16 23 recommended for 8 poles motors 5 Timing mode 4 5 groups gt 24 30 recommended for more than 10 poles motors and out runner motors O Setting of Frequency 1 Hear 5 groups or 5 gt P or 5 gt the above circulation put the throttle stick to the middle position 2 Frequency 1 5 groups 8 kHz For common setting the lowest efficiency loses 3 Frequency 2 5 groups gt 16 kHz recommended for the low internal resistance of motor 4 Frequency 3 5 groups gt 32 kHz recommended for the low electrical inductance of motor Diagram for Option parameter assistant by transmitter Function value setting by program Box By the Flier Program Box you can set all of function value very simply Setting procedure as follows 1 Connect the 4pin connector of ESC with the 4PIN connector in Prog Box Make sure the direction is correct 2 Connect ESC and motor 3 Power on the ESC and you will hear a p p gt melody it prompt that the connecting is ok and you can go on 4 Great Read ESC Data will be displayed on the LCD screen on the front of the Box after 1 second it will enter the
Download Pdf Manuals
Related Search
Related Contents
製品安全データシート Emerson (K580HC-K975A) Diagrams and Drawings Samsung RL43THCSW User Manual LabelManager® Manual de instruções Océ 9300 MAJIK-I Sea Gull Lighting 15170B-965 Instructions / Assembly Copyright © All rights reserved.
Failed to retrieve file