BRUSHLESS BLENDER N°62 USER AND MAINTENANCE MANUAL
Contents
1. 98162 EN 1 3 01 2010 www santos fr Assembling the bearing on the jar Place the bearing seal 16 on the bearing 12 Place the locking ring seal 18 on the locking ring 17 Place the bearing 12 inside the jar 1 Screw down the locking ring take care that the locking ring seal remains in its seating e Tighten well by hand or with a lever 98162 EN 1 3 01 2010 y www santos fr FAULT FINDING Identifying the cause of appliance stoppage with precision In all circumstances if the problem persists disconnect the electric power supply unplug the mains power cord 10 and call on someone from the maintenance department or contact an approved SANTOS dealer The appliance will not start The LCD screen does not light up e Check the mains supply the condition of the power cord 10 e Check that the On Off switch 4 is at position 1 e Check that the ammeter protection system has not been triggered due to an overload see the paragraph The appliance stops following a motor overload e Switch the appliance off then on again e After powering up the 6 key diodes should light up quickly and the screen display READY If not check on the condition of the wiring and connections in the switch 4 the component support module and the control panel this operation must be carried out by a qualified person The LCD screen shows NOT READY e This message indicates that one of the k2. 98162 EN 1 3 01 2010 www santos fr Element cross reference table 5 Control panel 6 Motor housing Protective hood 8 Hood lid 9 Jarmat Mains plug Blade Blade bearing Blade tightening nut Blade thrust washer 15 Blade shaft seal 17 Bearing tightening ring 19 Motor drive fixing screw 20 Motor drive D Table seal 29 LCD screen 29 Control panel keys 24 Blade drive Current overload protector Simplified list of appliance codes Functions Codes Universal menu 2 5 1 Coffee shop menu 2 5 2 J uice bar menu 2 5 3 Custom menu 2 5 4 Allocation of a recipe to a key 3 1 P Partial counter 4 5 2 Cleaning cycle 1 4 2 Activation of Pause Quick stop mode 4 P 1 98162 EN 1 3 01 2010 Ab www santos fr Figures 98162 EN 1 3 01 2010 www santos fr S SANTOS www santos fr 98162 EN 1 3 01 2010 Ab SANTOS y WARRANTY CERTIFICATE WARRANTY Since the 01 01 95 all our appliances comply with CE and possess the CE label Our guarantee is of 24 months from the manufacturing date mentioned on the descriptive plate except concerning the asynchronous motors consisting of a rotor and a stator which are warranted for 5 years from their manufacturing date Warranty is strictly limited to the free replacement of any part of origin recognized by us as defective due to a defect or building default and identified as belonging to th
3. e Do not hermetically close the jar when the appliance is stored away remove the lid 2 e Take care when handling the blade risk of cuts e Do not tap the jar against any surface to unstick ingredients use a flexible spatula instead You are advised to clean the appliance as soon as you have finished using it It will be easier to clean if you do not allow the remaining scraps of food to dry The motor surround 6 can be cleaned using a soft wet sponge Cleaning the jar Note Although the jar and lid can be washed in a dishwasher it is recommended not to do so in order to make them last longer 1 Empty the contents out of the jar and rinse with runnning water to remove as must solid residue as possible 2 Fill the jar with 600 ml warm water 40 to 45 C add 2 drops of household washing up liquid place the lid on the jar to close it and run the cleaning cycle code 1 4 2 30 seconds 3 Rinse thoroughly with clean water Sanitizing the jar Use the following procedure in order to be sure it is perfectly sanitized 1 Clean the jar and lid see preceding chapter 2 Fill the jar with 1 liter of sanitizing solution 75ml of sodium hypochlorite solution containing 2 6 active chlorine and top up to 1 liter with cold water 3 Close the jar using its lid and run the cleaning cycle code 1 4 2 30 seconds 4 Once the cycle has ended leave the solution to work for 2 minutes 5 Rinse thoroughly with
4. 01 2010 y www santos fr USING THE APPLIANCE CONTROL PANEL DESCRIPTION The control panel 5 is made up of e a graphic screen 22 e 6 recipe keys 23 including one P for pulse Each key corresponds to a predefined recipe USE Note the appliance will not start unless the hood lid 8 is closed Starting up 1 Power up the appliance by putting the On Off switch 4 to position 1 2 Put soft foods in the jar 1 first followed by the harder ones with ice cubes last of all Using pieces of food of even size make the recipe easier to carry out 3 Putthe lid 2 on the jar and check it is correctly positioned 4 Make sure the motor is turned off then install the jar on the jar mat 9 5 Close the sound proofing hood by lowering the lid 8 The LCD screen should show READY 6 Press one of the 6 keys 23 to start the cycle for the corresponding recipe Recipe 16 7 The lamp for the key activated will remain lit while KGG ore the cycle is in progress 8 Wait for the cycle to end Stopping the appliance The appliance will stop either e Automatically at the end of the cycle e Or by manual intervention by pressing one of the 6 keys on the control panel or by putting the switch to 0 Milkshake Small Note opening the sound proofing hood will trigger the LID OPEN ls pause mode The motor will stop When the sound proofing hood is closed again the cycle starts up again from whe
5. Never place the appliance close to or on a source of heat 98162 EN 1 3 01 2010 Le www santos fr SANTOS ELECTRICAL CONNECTION e The appliance s power supply is available in two single phase voltages 110 120 V 50 60 Hz 220 240 V 50 60 Hz Line protection the appliance must be connected to a standard 2 pole ground socket The set up must be fitted with a differential circuit breaker and a 16A fuse Grounding of the appliance is compulsory TAKE CARE Before connecting the appliance check that the mains electrical voltage is the same as the voltage for your appliance Its value is shown gt either on the identification plate under the appliance gt or on the identification plate on the last page of this manual TAKE CARE Check that the on off switch 4 is in position 0 Off before plugging the power cord in to the mains power socket 1st TIME USE Thoroughly clean all parts in contact with the food jar 1 lid 2 See the cleaning chapter RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE This appliance is marked with the symbol of the selective waste sorting system relating to waste electrical and electronic equipment This means that the product must be disposed of via a selective waste sorting system in accordance with directive 2002 96 CE DEEE Professional Appliances section so that it can be either recycled or dismantled in order to reduce any impact on the environment For
6. ANAN CT gc ese ta sa ceases ct rns es ye saw ess vst wea es ew cmon AA salves emote 9 PRE RECORDED RECIPE Kaire er A AA NA NG AA dd 9 Selecting a pre recorded Men Aa NAA NANA GAGA 9 COIN NN NA AA AA a a Race 10 CREATING C US TO MERECE Sa A AA AA 10 Creatine o o PP Ca AA AA 10 CLAN E Maa C Z e A A AA AA In 11 A a SS nt cece pace GE ERG O ANG 11 A o G ES AA 11 HOON SII PPT id AA AA 12 Modifying the safety mode connected with the hood NOI A ia AB GAIN 12 MAINTENANCE AA AANI De reta 12 DAR DORSO cards rara eee er lt A RO 12 Changing th drive o O ha een eae meer Te 12 Chant he DIGO ticas 13 FAULT INDIN Gusana A Con nat iii A ENEE 15 Tha panceta 15 NS DS does MOTOS a 16 The appliance stops as a result of an overload nr dape 16 The appliance stops further to an overload OV PRO A at A A id 16 The applhance resets while TAS Op rating aa ANA ANA a pag a EEE EEES A a a 16 Noises vibrations leaks at jar blade eL ERA EAE 16 Problemi AA 17 APPLIANCE TECHNICAL SPECIFICA TIONS usa caia N GNG BATIKANG GANGBANG 18 TECHNICAL ALECIFICATION Sr sta a ig ato 18 Wiring diagram 110 120V 50 60Hz and 220 240V 50 60HZ cccccccccecsessecececessscececeeesnnneececesseaaecececnssenaececeeeeaaeeeceseseeaaeeececneuaaececeseeaaeeceeeeneaeeeceeneaas 19 Element cross reference table AAA A e e ON OO OO 5 5 o RP A OO SSeS seses e te eeeses essene 20 Simplified list of appliance COTOS lt a us 20 WARRANTY CERTIFICATE recreia a EE aR SEEEN ANAN GAN
7. Input power 1000 Max current 5 Speed 2500 to 15000 Glass touch screen Cup capacity Pre recorded recipes Additional recipes parameterizable Partial counter Safety sound proofing hood USB Host port Motor overload safety feature Motor overheating safety feature Excess voltage safety feature Intermittent operation Dimensions Height Width Depth Weight Net weight Weight including packing Noise 2 Loa uncertainty K pa 2 5dB 1 These ratings are given for your guidance The exact electrical specifications of your appliance can be found on the rating plate 2 Noise level measured in acoustic pressure of appliance loaded as per the following standards NF EN 12852 2010 ISO 11201 1995 and ISO 4871 1996 Appliance placed on a work surface at 75cm from the floor Microphone turned towards the appliance at 1 6m from the ground and 1m from the appliance 98162 EN 1 3 01 2010 a www santos fr Wiring diagram 110 120V 50 60HZ and 220 240V 50 60Hz Control panel pee sees TM i cate GT sESE Motor vo O aa A S mam l Bundle l l l a _ O6 Th FA 1 7 option r Electronic gt O card O I O l i i E e NN eo ee l l i paa Black a ino a nn yuuiuiiuiuiiiii do ee old e e o eto oi l G l Loss sass sss ba A A Fan option Green yellow l I E Whit ite l i White Ammeter l protection Black ack White 1 z
8. clean water 98162 EN 1 3 01 2010 a www santos fr SANTOS j HOOD SAFETY FEATURE Note the appliance will not start unless the hood lid 8 is LID PEN closed Modifying the safety mode connected with the hood lid Pause mode by default While a cycle is running opening the hood makes the motor stop but does not clear the key that is active When Milkshake Small the hood is closed again the cycle resumes LID OPEN 10 Note the current cycle will be de activated if the sound proofing hood remains open for more than 30 seconds Quick stop mode Opening the hood makes the motor stop and de activates the key that was selected This code 4 P 1 provides the means for switching from one mode to the other MAINTENANCE Prior to carrying out any intervention on the appliance it must be disconnected from the mains without fail Spare parts This appliance requires no specific maintenance The bearings are lubricated for life lf any intervention is necessary to replace paris subject to wear such as the bearing blade electrical or other components please refer to the parts list see the exploded view at the end of this manual Whenever ordering spare parts see references in the exploded view at the end of this manual please quote the following gt the type gt the appliance serial number and gt the electrical specifications 16 given under the appliance Changing the
9. than double the quantities and cycle time prolonged operation heats the food due to friction and affects the desired texture with the recipe The final mixture is too hot Once an evenly mixed texture has been obtained carrying on blending will make the food heat up reduce the speed or recipe time The final mixture is not even in texture e the recipe is not appropriate for the quantity and products processed reduce the quantity of food in the jar increase the cycle time use smaller pieces of food having evenly sized pieces of food makes it easier to carry out the recipe e Liquid is needed to make the solid food reach the blade Increase the amount of liquid pour in the liquid before adding the solid foods Ice cubes remain stuck to the jar walls e Reduce the quantity of ice cubes when they are processed without any liquid e Itis better to add liquid with the ice cubes always putting the liquid in first The mixture bounces fast up and down the jar e Reduce the speed to adapt it to the quantity being processed so that the blade is constantly immersed in the mixture The recipe will take place more quickly and the mixture will be more even High speeds are not suitable for recipes with small quantities e Increase the amount of product being processed 98162 EN 1 3 01 2010 a www santos fr APPLIANCE TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS Single phase 220 240 100 120 50 60 50 60 Motor Nominal
10. the appliance without any food in the jar 5 Fill the jar beyond the maximum capacity corresponding to the amount marked on the side 1 4 liters The maximum capacity must be reduced for thick mixtures 6 The base 6 must not be immersed in water 7 Plunge the base in water or any other liquid for reasons of protection against risks of electrocution 8 Use the appliance if the power cord is damaged lt must be replaced by a special assembly available from an approved SANTOS dealer or from SANTOS itself 9 The appliance must be unplugged before any intervention on it cleaning general care maintenance 10 Use a hose nor a pressure hose for cleaning this is forbidden 11 Use an abrasive sponge to clean the plastic jar 1 12 Insert or store kitchen utensils in the jar 13 Operate the appliance if the jar or a blade is chipped cracked or broken Never use a jar if there is any play with respect to the blade 14 It is forbidden to operate the appliance on a surface with a slope in excess of 10 relative to the horizontal plane All 4 feet of the appliance must always be resting on this surface The appliance motor shaft must always be vertical relative to the surface on which it is placed 15 Use of spare parts other than certified original SANTOS parts is prohibited 16 Turn the On Off switch 4 to 0 when the appliance is not operating 17 Connect several appliances to the same power socket 18 Use the appliance outdoors 19
11. A NAGA 23 APPLIANCE IDENTIPICA TION PLATE GAGABAY ABANGAN BAGA TANANG ANAN ANAN RG AGA NI 23 98162 EN 1 3 01 2010 www santos fr CE COMPLIANCE DECLARATION THE MANUFACTURER SANTOS sas 140 150 Av Roger SALENGRO 69120 VAULX EN VELIN LYON FRANCE declares that the appliance intended for the professional market described below Description BRUSHLESS BLENDER Type number 62 complies with e the statutory provisions defined in appendix 1 of the European machines directive n 2006 42 CE and the national legislation transposing it e the statutory provisions of the following European directives and regulations o N 2006 95 CE low voltage directive N 2004 108 CE EMC directive No 2002 95 CE RoHS directive No 2002 96 CE WEEE directive N 1935 2004 CE regulation relating to materials and articles intended to come into contact with foodstuffs O O O O Harmonised European standards used to give presumption of conformity with the essential requirements of the above mentioned directives e NF EN 12852 A1 2010 Food processing machinery Food preparation equipment and blenders Safety and hygiene requirements This European standard is a type C standard as defined in EN ISO 12100 When the provisions of this type C standard differ from those stated in the type A or B standards the provisions of the type C standard override the provisions of the other standards This standard provides the means to compl
12. ON AND HANDLING Installation on a counter The appliance can be handled by a single person For ease of use it is recommended that the appliance is placed on a table or work surface so as to have the control panel in front of you recommended height 90 cm to be adapted as required for the user Installation when built into the countertop Before cutting out the countertop check the following points in order to be sure that the appliance will be perfectly usable once built in 98162 EN 1 3 01 2010 Ay www santos fr la y HITANO PA VAIL IN a Make sure there is sufficient clearance behind above below for proper installation and operation of the appliance The cut out in the countertop represents a rectangle measuring 168mm x 198mm e Make sure there is a minimum clearance of 135mm beneath the countertop e The free space above must measure at least 495mm e The minimum clearance to the rear must be 102mm distance between the cut out and the wall e The minimum clearance sideways must be 30mm Multiple cut outs It is recommended to leave a distance of 100mm between 2 cut outs Adapting the appliance to use it as a built in version e Disconnect the appliance from the mains e Remove the jar 1 and hood lid 8 e Tip the appliance backwards e Using a Torx screwdriver remove the 3 screws located between the metal casing and motor surround 6 e Remove the motor surround 6 98162 EN 1 3
13. SANTOS SAS 140 150 AVENUE ROGER SALENGRO o 69120 VAULX EN VELIN LYON FRANCE TEL 33 0 472 37 35 29 FAX 33 0 478 26 58 21 mm SANTOS E Mail santos santos fr www santos fr BRUSHLESS BLENDER N 62 USER AND MAINTENANCE MANUAL IMPORTANT documents included in this manual to be kept e CE COMPLIANCE DECLARATION e WARRANTY CERTIFICATE Read the instructions for use before unpacking the appliance Coffee grinders Fruit squeezers Mixers Blenders Drinks dispensers Mixer beaters Dough mixer Cheese graters Ice crushers Mincers Vegetable cutters INTERNATIONALLY PATENTED MODELS CONTENTS CE COMPLIANCE DECLARATION 2a AA ao nado nina ade silas avisada dades incide AA 3 SAFETY RULES RARA Er PRADO ERROS ERES PR ROS nE aeaaea E EO NANANA CR ARA RU DR RO UERR PORRA DRA ER URNA PEER 4 PONOT EEEE E EOE AE rara 4 CECT CONNECTION ari ra 5 Dom NIT asp siso O AA a e a RECYCLING THE PRODUCT AT THE END OF TES SERVICE LIBER ad adiada pasa 5 DESCRIPTION OF THE APPLIANCE sonia AAA AAA AA AA NAAANINAG 6 INSTALLATION AND HANDLING saveiro setihadnncesdaacbobysncnsdessae baat dla 6 cis A o Dj ER DS 6 Installation when built into the Contento Dalila 6 USING TUE APPERTAN Clinico AA T I A 8 CONTROL PANEL DESC RIC DON tania 8 Ey POPE CPU O UE A A ct E EE EE A A A A 8 Starine 1 0 ORAR O Pomo TEO cas creat ci nw entire E poet hee E atte cemeteries 8 Stoppins th os PP ncn cites ceca rc ga a e AA dg 8 Cyle Counter ANA
14. drive system Motor drive female Hold the motor drive 20 in position with multiple slip joint pliers and unscrew the fixing screw 19 using a TORX wrench anticlockwise 98162 EN 1 3 01 2010 ay www santos fr Blade drive male The blade drive is an integral part of the jar ball bearing assembly 12 The whole assembly must be replaced drive main bearing ball bearing e Turnthe jar upside down e Using a large flat screwdriver loosen the bearing fixing ring 17 anticlockwise e Remove the bearing fitted with the blender blade from the jar see next section for how to dismantle the blade Changing the blade Dismantle the complete bearing assembly see previous section Dismantling the blade Hold the blade coupling 24 in position with multiple slip joint pliers and unscrew the fixing nut 13 using a size 12 hexagon wrench anticlockwise Fitting the blade Take care to comply with the order given for assembly of the various components 1 lipped seal 15 be sure to install correctly with lip downwards 2 thrust washer 14 Sa CC 3 blade 11 recesses ma upwards 4 thrust washer 14 the lipped seal must be pushed far enough for the square of this washer to work with the square of the shaft 5 fixing nut 13 tighten the nut by hand checking that the washer in point 4 is correctly positioned relative to the square of the shaft Tighten the fixing nut
15. e concerned appliance Warranty does not apply to damages resulting from installation or use non complying with our appliance data sheet users manual or in case of an evident lack of maintenance or disrespect of elementary security electric rules It does not apply in case of regular wear and tear Any replacement of parts under warranty will be realized after return of the defective part in our workshops postage paid supported by a copy of a conformity statement on which appears the serial number of the appliance Every appliance is equipped with a descriptive plate conforming to the EC recommendations and of which a duplicate exists in the conformity statement serial number manufacturing date electrical characteristics In case of serious damage judged repairable only in our workshops and after prior consent from our departments any appliance under guarantee is sent by the Distributor carriage paid In case of repairs or reconditioning of appliances not under guarantee the round trip transport is payable by the distributor The parts and workforce are invoiced at the current rate A preliminary estimate can be supplied Coffee grinder not using SANTOS original burrs are not taken under guarantee The warranty conditions repairs reconditioning of the espresso coffee grinder are the object of a specific note Our guarantee does not extend to the payment of penalties the repair of direct or indirect damages and notably to any loss of inco
16. enu Your own menu can be created by assigning one of the 30 pre recorded recipes to one of the 6 keys on the control panel How to assign a recipe to one of the control panel keys Note All 6 keys can be parameterized For example to assign recipe n 34 to key n 2 select key e Type in the following sequence a 1 as p e Select the key to be programmed Press key n 2 Enter recipe codes Enter the code for the desired recipe see the table of 30 pre recorded recipes Type code 34 on the keys Change Assignment thers Escape e Press key 1 to validate or one of the other keys to cancel Once the custom menu has been set up the standard menus can be activated using the appropriate code without deleting the custom menu Use the code 2 5 4 to reactivate the Custom menu CREATING CUSTOM RECIPES Creating custom recipes Your own recipes can be created by using a special program available ffom SANTOS and a simple USB key for transfer ffom computer to the appliance Note No special casing is required 98162 EN 1 3 01 2010 Ab www santos fr CLEANING IMPORTANT e Inall cases stop the appliance and unplug the power cable 10 e The appliance must not be cleaned with a jet of water nor a high pressure spray e The motor unit 3 must not be immersed in water e Do not use an abrasive sponge to clean the jar 1 protection hood 7 and lid 8 nor the control panel 5
17. eys was already activated before powering up e Remove any item liable to activate the keys clean the control panel TORTO IO The LCD screen shows LID OPEN e Close the safety hood lid 8 LID OPEN The LCD screen shows READY e Switch the appliance off then on again e After powering up the 6 key diodes should light up quickly and the screen display READY e lf not check the connections on the cable connecting the control panel to the electronic module this operation must be carried out by a qualified person 98162 EN 1 3 01 2010 Ab www santos fr The blade does not rotate e Check that there are no foreign bodies stuck in the jar e Check the condition of the drive system motor and blade The appliance stops after the motor has overheated OVER TEMP the motor unit is hot e Put the On Off switch 4 to the O position and unplug the appliance e Wait for the motor to cool down 20 to 45 minutes then press the On Off switch 4 position 1 The appliance stops as a result of an overload The LCD screen does not light up A motor overload can occur if there is an excessive quantity or something too hard in the jar Under these circumstances either the thermal protection or the excess current protection may be activated and stop the appliance operating lf the appliance is hot refer to the section The appliance stops as a result of motor over heating Otherwise e Turn off the elect
18. further information you can contact your dealer or SANTOS For the disposal or recycling of the appliance components please refer to a specialist company or contact SANTOS Electronic products not covered by a selective sorting system are potentially dangerous for the environment The packaging material should be disposed of or recycled in accordance with regulations in force Table showing the proportions of materials making up the appliance percentage weight Total steel Total Total plastic Total copper Miscellaneous aluminum materials 31 1 19 0 33 2 13 8 Weight of miscellaneous materials e g switches electronic boards capacitors electric cables etc 98162 EN 1 3 01 2010 y www santos fr DESCRIPTION OF THE APPLIANCE e Appliance n 62 is a professional appliance designed exclusively for professional use It is not designed for household use e Appliance n 62 is made for the preparation of cocktails smoothies and all types of preparation based on crushed ice and blended fruit which may be produced in bars cafes hotels or restaurants e The appliance consists of a blender jar a motor base fitted with an On Off switch an electronic module a control panel and a sound proofing hood e Some thirty recipes show how to prepare most of the desired preparations e The appliance has a USB Host connection allowing 6 custom recipes to be updated along with the appliance s Firmware INSTALLATI
19. me resulting from the nonconformity or the defectiveness of products SANTOS s global responsibility being limited to the sale price of the delivered product and to the possible repair of the defective products In case of revelation of an imperfection during the warranty period the Distributor has to unless a different written agreement of SANTOS indicate to his customer to stop any use of the defective product Such a use would release SANTOS of any responsibility APPLIANCE IDENTIFICATION PLATE SPECIMEN For all documents not supplied with the appliance Printed Faxed and Downloaded 98162 EN 1 3 01 2010 www santos fr
20. re it stopped unless the hood remains open for more than 30 seconds 98162 EN 1 3 01 2010 Le www santos fr SANTOS y Cycle counter The stop function has a partial cycle counter which allows the number of recipes carried out over a given period to be counted This code 4 5 2 is used to view the counter e Hit the 1 key to reset the counter to zero while viewing it PRE RECORDED RECIPES The appliance is delivered with 3 basic menus loaded as standard each containing consisting of 6 recipes among the 30 recipes pre recorded in the appliance e Universal menu which allows most recipes usually needed to be carried out e Coffee shop menu which is more suited to coffee shops e Juice bar menu which is more suited to juice bars Note Each menu has 6 recipes A recipe consists of several sequences speed time here is an example of a recipe Selecting a pre recorded menu The menus are selected using the following key combinations Universal menu press the following keys in quick succession 2 5 1 Coffee shop menu press the following keys in quick succession 2 5 2 Juice bar menu press the following keys in quick succession 2 5 3 Custom menu press the following keys in quick succession 2 5 4 Note when the appliance is delivered the Custom menu is empty See the following section on how to enter parameters 98162 EN 1 3 01 2010 Le www santos fr SANTOS Custom m
21. ric power supply unplug the mains power cord 10 e Move the On Off switch 4 to the O position e Under the appliance fig O press the button 25 to reset the excess current protection If the button does not remain in the reset position allow the appliance to cool down before repeating the operation The appliance stops further to an overload OVERLOAD Reduce load OVERLOAD A motor overload can occur if there is an excessive quantity or something too hard in the jar e The recipe is not appropriate for the quantity and consistency e Reduce the quantity e Chose a different recipe with slower speeds The appliance resets while itis operating Eliminate all multiple power sockets and plug the appliance into its own individual power supply Noises vibrations leaks at jar blade level e Check the blade is correctly tightened first dismantle the blade bearing e Replace the bearing seals See the chapter Changing the blade lf the problem persists turn the appliance electric power off unplug the mains power cord 4 and call on someone from the maintenance department or contact an approved SANTOS dealer 98162 EN 1 3 01 2010 a www santos fr Problem with the recipes A few basic rules make it easier to understand how a blender works and thus know how to adapt the recipe cycles to the producis being processed Note Do not overload the appliance it is better to run a short recipe twice rather
22. y with the requirements of the machines directive n 2006 42 CE see appendix ZA e NF EN ISO 12100 1 and 2 2004 Safety of machinery General principles for design e NF EN 60204 1 2006 Safety of machinery Electrical equipment of machines General requirements e NF EN 1672 2 2005 Food processing machinery Basic concepts Hygiene requirements e NF EN 60335 1 2003 Household and similar electrical appliances Safety e NF EN 60335 2 64 2004 Particular requirements for commercial electric kitchen machines Drawn up in VAULX EN VELIN on 01 12 2010 Signatory s position CHIEF EXECUTIVE OFFICER Signatory s name Aur lien FOUQUET f a A E Fa Fi AR E ThA Eas Signature 98162 EN 1 3 01 2010 WN www santos fr SAFETY RULES At the time of use maintenance or scrapping of the appliance always ensure that the following elementary precautions are adhered to Read the explanatory instructions in full Keep this user manual Note You will find it easier to understand the next few paragraphs if you refer to the diagrams at the end of this manual DO NOT 1 Use this appliance to process anything other than foodstuffs 2 Pass the pits through the appliance Remove the pits from fruits before passing them in the appliance e g mangos apricots peaches 3 Use the appliance without first correctly installing the jar 1 fitted with its lid 2 on the motor base 3 4 Operate
Download Pdf Manuals
Related Search