Home

Kit for EVO4, Solo/SoloDL on Ducati 899, 1199 and 1299

image

Contents

1. To connect EVO4 and SoloDL to the ECU of the bike use the connector you find under the passenger seat Open the bike tail and remove the connector cup highlighted in the image here on the right Once the cup has been removed the connector appears as here on the right iD Connect AiM wiring to Ducati wiring as here on the right Take the cable to the logger as here on the right To reach SoloDL make the cable pass between the fuel tank and the bike frame Please avoid positions where the cable would be exposed to direct heat User Guide CTD User Guide The image here on the right shows the cable reaching SoloDL Connect the cable to SoloDL as here on the right CTD User Guide To connect AiM SoloDL to V02569170 cable use the seven pins Binder 712 female connector placed right under the logger as shown here below 4 pins FCI male connector 4x0 35mm cable 7 pins Binder 712 L_ male connector To connect AiM EVO4 to V02563150 cable use the five pins Binder 712 female connector labelled ECU of the logger third from the left on the top row as shown here below speed m SOE OC FQ 0006 Q CH1 r H2 4 pins FCI male connector 3x0 35mn cable J a 5 pins Binder 712 male connector 4 CA User Guide Configuring with Race Studio 2 Before connecting the bike ECU to EVO4 SoloDL to set these last up using AiM Race Studio 2 software The pa
2. cylinder lambda diagnosis Front brake pressure Rear brake pressure Ducati traction control intervention Ducati traction control percentage Engaged gear Ducati traction control level Map selection Technical note not all data channels outlined in the ECU template are validated for each manufacturer model or variant some of the outlined channels are model and year specific and therefore may not be applicable
3. AiM User Guide Kit for EVO4 Solo and SoloDL on Ducati 899 1199 Panigale and 1299 Panigale Release 1 04 PFPA RNIGA L E CTD User Guide 1 Models and years This user guide explains how to install AiM Solo and SoloDL on Ducati Panigale bikes and how to connect EVO4 and SoloDL to the bike Engine Control Unit ECU Supported models and years are e 899 Panigale from 2013 e 1199 Panigale 2012 2015 e 1299 Panigale 2015 Warning AiM recommends not to remove the bike stock dash 2 Solo SoIoDL kit and EVO4 ECU connection cable AiM developped an installation kit with bracket and ECU interface cable for Solo SoloDL and an ECU interface cable for EVO4 CTD User Guide 2 1 Kit and bracket for Solo SoloDL on Ducati Panigale Solo SoloDL installation kit is shown here below part number is VO2569170CSP The kit includes 1 bracket 1 2 4x10 Allen screws with countersunk head 2 1 washer 3 1 rubber distance piece 4 1 8x45 pan head Allen screw 5 1 AiM ECU interface cable for Ducati Panigale 6 AiM cable 6 and bracket 1 can also be bought separately as spare parts e SoloDL cable for Ducati Panigale V02569170 e Solo SoloDL bracket for Ducati Panigale X46KSTSDP CTD User Guide 2 2 AiM cable for SoloDL AiM cable for SoloDL on Ducati bikes is shown below its part number is V02569170 The image here below shows the cable constructive scheme 1 White CAN A Blue CAN 3 R
4. ed Vbext la lo 4 ne e e 6 AI 2 ft nc TE nc m o aM 7 pins Binder 712 male z Black GND connedor Pinout solder termination view 4 pins FCI 4 male connetor pinout contact insertion view CTD User Guide 2 3 AiM cable for EVO4 AiM cable for EVO4 on Ducati bikes is shown below its part number is V O2563150 The image here below shows the cable constructive scheme 4 ne D Blak GND 3 White CAN a O Blue CAN 44 5 pins Binder 712 ue PELI male connector pinout solder termination view 4 pins FCI male connedor pinout contact insertion view CTD User Guide 3 Installation and connection Here you find the instructions to install Solo and SoloDL on Ducati Panigale and to connect EVO4 and SoloDL to the bike ECU EVO4 cable length allows installation of the logger under the bike seat 3 1 Installation of Solo and SoloDL To install Solo SoloDL on your Ducati bike Place the washer and the rubber distance piece in line with Panigale bracket hole and insert M8 screw tightening all pieces Fix Solo bracket to Panigale one using the two countersunk screws you find in the kit Insert the assembled brackets in the handle bar hole Tighten the M8 screw and the distance piece until the assembled brackets about the bike fork Hook Solo to its bracket Tighten Solo bracket screws User Guide CTD User Guide 3 2 Connection of SoloDL and EVO4 to the bike ECU
5. rameters to select in the logger configuration are e ECU Manufacturer Ducati e ECU Model Panigale 5 Ducati protocols Channels received by SoloDL and EVO4 connected to Ducati Panigale protocol are ECU_1 ECU_2 ECU_3 ECU_4 ECU_5 ECU_6 ECU_7 ECU_8 ECU_9 ECU_10 ECU_11 ECU_12 ECU_13 ECU_14 ECU_15 CHANNEL NAME ECU_RPM ECU_SPD_REAR ECU_TPS1_ENG ECU_TPS2_ENG ECU_TPS_HAND ECU_WATER_T ECU_SPD_FRONT ECU_INT_AIR_TEMP ECU_BATTERY ECU_BRAKE_SW ECU_CLUTCH_SW ECU_NEUTRAL_SW ECU_OILP_SW ECU_TURN_RIGHT ECU_TURN_LEFT FUNCTION RPM Rear speed Throttle position cylinder 1 Throttle position cylinder 2 Manual throttle Engine coolant temperature Front speed Intake air temperature Battery supply Brake switch Clutch switch Neutral switch Oil pressure switch Right turn indicator Left turn indicator ECU_16 ECU_17 ECU_18 ECU_19 ECU_20 ECU_21 ECU_22 ECU_23 ECU_24 ECU_25 ECU_26 ECU_27 ECU_28 ECU_30 ECU_31 ECU_32 CLL ECU_SW_ENG_MAP ECU_SW_BEAM ECU_BARO ECU_LAMB_H ECU_LAMB_TMP_H ECU_DIAG_H ECU_LAMB_V ECU_LAMB_TEMP_V ECU_DIAG_V ECU_BRK_FRONT ECU_BRK_REAR ECU_DTC_RDC ECU_DTC_PERC ECU_GEAR ECU_DTC_LEV ECU_MAP_SELCT User Guide Engine MAP selector High beam switch Barometric pressure Horizontal cylinder lambda value Horizontal cylinder lambda temperature Horizontal cylinder lambda diagnosis Vertical cylinder lambda value Vertical cylinder lambda temperature Vertical

Download Pdf Manuals

image

Related Search

Related Contents

HP Wheelchair B User's Manual  Notice of Postal Ballot & poster ballot form  Documentation - Manu Lorraine  Manual de Instrucciones  79160 Gartenkultivator_cover_ES-IT-PT.indd  Yamaha DME64N/24N V2 Owner's Manual  NI PXI-1045 User Manual - Artisan Technology Group  UMO-5200  Kingston Technology ValueRAM 1GB 333MHz DDR ECC Registered CL2.5 DIMM BGA Dual Rank, x4  Hilti 3476293 Use and Care Manual  

Copyright © All rights reserved.
Failed to retrieve file