Home

CIM 250 SMS commands

1. 3712 55 68 15 3712 53 36 35 Revised 18 04 2013 Grundfos companies be think innovate S v sojpunio 1uBuAdo PIMPLOM pamasa syu Iv ueuueg S Y sojpunio 10 S Y Aq paumo peuejsi amp e ayeaouu yury eq pue sojpunio y sojpunuo eu 96861082 0513 ECM 1113692 A n 0 L A Z 5 U www grundfos com
2. AI1NAME Illegal name Negative format acknowledgement symbolic parameters section 2 1 The text configuration of signals is accepted whether the IO 270 module is present or not as long as the command syntax is correct Seeing the status of configured signal texts is only possible with the command IOSTATUS if there is an IO 270 24 Temperature input TI1 has a fixed scaling of 50 204 C corresponding to the scaling in the corresponding Modbus register 01222 IO270 Temperature Leaving out all arguments to one of these commands will reset the scaling of the input in question to its factory setting 0 100 96 An acknowledgment SMS is replied to the phone This is shown below for command Al1SCALE Note Positive acknowledgement changed scaling AI1SCALE Changed to range lt value gt to lt value gt lt alpha string gt Positive acknowledgement reset to default AI1SCALE Scaling reset to factory scaling 0 100 Negative acknowledgement AI1NAME Illegal or missing command parameter The negative acknowledgement appears if one or more command parameters are missing or have a syntax error or if the scaling range is inconsistent The configuration of signal scaling is accepted whether the IO 270 is present or not as long as the command syntax is correct To see the status use the command IOSCALING 7 41 270 operation IOSTATUS Command to request status
3. Sets the Grundfos product to remote controlled operation The Grundfos product is controlled via the CIM 250 LOCAL Sets the Grundfos product to locally controlled operation The setpoint operating mode and control mode can be changed on the product or by means of a Grundfos R100 remote control START Starts the Grundfos product STOP Stops the Grundfos product MIN Changes the operating mode of the Grundfos product to Min It will run according to the min curve MAX Changes the operating mode of the Grundfos product to Max It will run according to the max curve SETPOINT value Sends a new setpoint value to the product If the setpoint is outside the permissible range it will automatically be changed to the nearest value within the range Due to the limited scaling range and the resolution the resultant setpoint may deviate from the one sent to the product Closed loop The setpoint is specified as a decimal point value scaled in the same unit as the feedback sensor The command STATUS provides information about the sensor scaling Note UPE and MAGNA pumps always use m Units on the MPC display can differ from unit if other units than standard SI units have been selected for sensors Open loop The setpoint is specified as a decimal point value scaled in 96 CONSTCURVE This command sets the Grundfos product to control mode Constant curve CONST
4. This fault type will probably disappear by itself as the message is typically triggered by a short power cut In case of this special fault but not the other ones the CIM 250 will send a message telling that the fault has disappeared Installation name GSM module Mains supply returned If the battery is worn out or the CIM 250 has no battery the CIM 250 will not detect if the power supply to the Grundfos product has been interrupted as it will loose power supply itself It can therefore not send a message To inform the user that there has been a power cut the CIM 250 will always send a message when the power supply has returned Installation name GSM module Power on occurred 22 6 3 Change GSM module battery If the CIM 250 detects that the battery is worn out and must be replaced it will send this message to all numbers in the phone number list Installation name GSM module error Change GSM module battery Note The CIM 250 GSM module battery is optional 6 4 GSM module battery low If the CIM 250 detects that the battery level is low it will send this message to all numbers in the phone number list Installation name GSM module error GSM module battery low Note The CIM 250 GSM module battery is optional 7 Additional SMS functionality of the CIU 251 7 1 Introduction The CIU 251 consists of a CIM 250 module and an IO 270 multipurpose I O module mounted in a CIU box See fig 1 T
5. 49 0 211 929 69 0 Telefax 49 0 211 929 69 3799 e mail infoservice grundfos de Service in Deutschland e mail kundendienst grundfos de HILGE GmbH amp Co KG Hilgestrasse 37 47 55292 Bodenheim Rhein Germany Tel 49 6135 75 0 Telefax 49 6135 1737 e mail hilge hilge de Greece GRUNDFOS Hellas A E B E 20th km Athinon Markopoulou Av P O Box 71 GR 19002 Peania Phone 0030 210 66 83 400 Telefax 0030 210 66 46 273 Hong Kong GRUNDFOS Pumps Hong Kong Ltd Unit 1 Ground floor Siu Wai Industrial Centre 29 33 Wing Hong Street amp 68 King Lam Street Cheung Sha Wan Kowloon Phone 852 27861706 27861741 Telefax 852 27858664 Hungary GRUNDFOS Hung ria Kft Park u 8 H 2045 T r kb lint Phone 36 23 511 110 Telefax 36 23 511 111 India GRUNDFOS Pumps India Private Limited 118 Old Mahabalipuram Road Thoraipakkam Chennai 600 096 Phone 91 44 2496 6800 Indonesia PT GRUNDFOS Pompa Jl Rawa Sumur Ill Blok III CC 1 Kawasan Industri Pulogadung Jakarta 13930 Phone 62 21 460 6909 Telefax 62 21 460 6910 460 6901 Ireland GRUNDFOS Ireland Ltd Unit A Merrywell Business Park Ballymount Road Lower Dublin 12 Phone 353 1 4089 800 Telefax 353 1 4089 830 Italy GRUNDFOS Pompe Italia S r l Via Gran Sasso 4 1 20060 Truccazzano Milano Tel 39 02 95838112 Telefax 39 02 95309290 95838461 Japan GRUNDFOS Pumps Gotanda Metalion Bldg
6. WARNSIM code Simulation of warning with event code 8 6 IO 270 related configuration commands Configuration Command Description Default setting 1 text Naming of analog input 1 11 Empty AI2NAME text Naming of analog input 2 AI2 Empty TI NAME text Naming of temperature input TI1 Empty DI1NAME text Naming of digital input 1 DI1 Empty DI2NAME text Naming of digital input 2 DI2 Empty DI3NAME text Naming of digital input 3 DI3 Empty DIANAME text Naming of digital input 4 D14 Empty AO1NAME text Naming of analog output AO1 Empty DO1NAME text Naming of relay output DO1 Empty Paging svalue gt scaling of analog input 1 0 100 capa seine lt value gt scaling of analog input 2 Al2 0 100 s cute lt value gt scaling of analog output AO1 0 100 IOSMS ON OFF Enable disable self triggered IO event messages OFF SETAMLEVEL value Monitor level for analog input 1 11 100 96 SETAI2LEVEL value Monitor level for analog input 2 AI2 100 96 SETTI1LEVEL value Monitor level for temperature input 1 TI1 100 96 30 8 7 IO 270 related status commands Status Command Description IOSTATUS Status of values measured by the IO 270 IOSCALING Status of the IO 270 analog signal scaling GETLEVELS Displaying monitor values of Al1 AI2 and TI1 8 8 IO 270 related contro
7. been enabled Numerical characters in front of command will generally be ignored if the access code has not been enabled A space character after access code is optional A legal command as explained in the following sections If a parameter is entered after command the command there must be one or more space characters between the command and the parameter One or more legal parameters for the command in question The use of symbolic parameters is explained here h b XX YYY ZZZ ZZZZ according to ITU T E164 For local SEGUE HUS calls and the country code XX are not required acess options LIST CODE BOTH NONE 5 P d See section 3 Configuring the CIM 250 access code Four numerical characters between 0 and 9 4 digit code zalpha Max 50 characters 2 a z 0 9 string AEN Peus eu s Max 64 characters A Z a z 0 9 and g gt Must not begin or end with and day of week ALL MON TUE WED THU FRI SAT SUN hour of day OFF 0 1 2 24 0724 parameter _ parameter installation name All printable characters except and 1 The number of digits depends on the country IP address XXX XXX XXX XXX Xxx 7 000 255 port number 1 65535 Default setting Modbus 502 GENIpro 49152 lt setpoint gt Decimal number with or without a decimal point lt event code gt Alarm warning eve
8. 250 will acknowledge the change with this message HEARTBEAT Changed to lt hour of day gt o clock on lt day of week gt or HEARTBEAT Changed to OFF Example of command HEARTBEAT 12 MON THU This command will result in a heartbeat message at 12 o clock Monday and Thursday every week A heartbeat message contains the same information as a STATUS1 message and will sent to all numbers in the phone number list Example of heartbeat message Installation name HEARTBEAT Device OK Setpoint 75 Act setpoint 6 5 m Act value 6 2 m START from GSM CONTROL Const press Continued on the next page Description Device OK will be replaced by an alarm warning text if there is a fault in the device See section 4 Status commands To perform the function the CIM 250 depends on time information being available The CIM 250 normally gets the time value from the GSM network upon initialisation after a power cut If this service is not available in the network and the heartbeat function has been activated the CIM 250 will send this message NOTICE Your GSM network does not support time information Please enter TIME yyyy mm dd hh mm for the heartbeat function to work Note If the message is sent because the heartbeat function was activated it will only be sent to the phone number that activated the function If the message is sent because of missing time information at initialisat
9. Przezmierowo Tel 48 61 650 13 00 Fax 48 61 650 13 50 Portugal Bombas GRUNDFOS Portugal S A Rua Calvet de Magalhaes 241 Apartado 1079 P 2770 153 Pago de Arcos Tel 351 21 440 76 00 Telefax 351 21 440 76 90 Romania GRUNDFOS Pompe Rom nia SRL Bd Biruintei nr 103 Pantelimon county Ilfov Phone 40 21 200 4100 Telefax 40 21 200 4101 E mail romania grundfos ro Russia 109544 39 Ten 7 495 737 30 00 564 88 00 7 495 737 75 36 564 88 11 E mail grundfos moscow grundfos com Serbia GRUNDFOS Predstavni tvo Beograd Dr Milutina Ivkovi a 2a 29 YU 11000 Beograd Phone 381 11 26 47 877 11 26 47 496 Telefax 381 11 26 48 340 Singapore GRUNDFOS Singapore Pte Ltd 25 Jalan Tukang Singapore 619264 Phone 65 6681 9688 Telefax 65 6681 9689 Slovenia GRUNDFOS landrova 8b 51 1231 Ljubljana rnu e Phone 386 1 568 0610 Telefax 386 1 568 0619 E mail slovenia grundfos si South Africa GRUNDFOS PTY LTD Corner Mountjoy and George Allen Roads Wilbart Ext 2 Bedfordview 2008 Phone 27 11 579 4800 Fax 27 11 455 6066 E mail Ismart grundfos com Spain Bombas GRUNDFOS Espa a S A Camino de la Fuentecilla s n E 28110 Algete Madrid Tel 34 91 848 8800 Telefax 34 91 628 0465 Sweden GRUNDFOS AB Box 333 Lunnagardsgatan 6 431 24 M lndal Te
10. the CIM 250 Command Description Basic status GSMSETTINGS Status of basic configuration LIST Phone number list SIGNALLEVEL GSM network signal level VERSION Version information BATTERY Battery status NETWORK GSM network status GSMDATA GSM statistics GPRS status GPRSSETTINGS GPRS settings GPRSSTATUS GPRS status GPRSDATA Modbus TCP status SCADA status SCADA SCADA settings 8 3 Control commands for the CIM 250 Command Description RESETGSM Resetting of GSM data counters RESETGPRS Resetting of GPRS data counters 8 4 Status commands for the product Command Description STATUS1 Primary status of the Grundfos product STATUS2 Secondary status of the Grundfos product 29 English GB 89 usu6u3 8 5 Control commands for the product Command Description RESETALARM Resetting of alarms and warnings REMOTE Setting to remote control LOCAL Setting to local control START or NORMAL Setting to operating mode Start STOP Setting to operating mode Stop MIN Setting to operating mode Min MAX Setting to operating mode Max SETPOINT value Setting of setpoint CONSTCURVE Setting to control mode Constant curve CONSTPRESS Setting to control mode Constant pressure PROPPRESS Setting to control mode Proportional pressure AUTOADAPT Setting to control mode AUTOApApT ALARMSIM code Simulation of alarm with event code
11. to enable and disable GPRS roaming if roaming for GSM and SMS communication is enabled with the command ROAMING Default setting OFF MODBUSPORT lt port number gt It will only be necessary to change the default setting of the Modbus port number in very special cases Default setting 502 GENIPROPORT lt port number gt Used for GPRS connection to a Grundfos PC Tool It will only be necessary to change the default setting of the GENIpro port number in very special cases Default setting 49152 13 English GB 89 usua Command Description SETGPRS 14 parameters It is possible to configure the GPRS connection with this single multiparameter command Parameters lt APN gt APN string or IP address Modbus port 1 65535 GENIpro port 1 65535 user name gt alpha numeric string lt password gt alpha numeric string lt authentication gt NORMAL SECURE connection SERVER CLIENT DISABLED lt GPRS roaming ON OFF Example 1 SETGPRS Grundfos dk2 tdc 502 49152 Grundfos 4321 NORMAL SERVER OFF Example 2 SETGPRS Grundfos dk2 tdc 502 49152 NORMAL In the second example some parameters have been omitted in the middle and at the end of the parameter string The CIM 250 acknowledges the change with the same message as for the status command GPRSSETTINGS 4 Status commands It is possible to get information about the status of the CIM 250 and the G
12. 37 C Battery charging Yes Charging suspended No Battery charging is suspended if the temperature is too high NETWORK 16 With this status command it is possible to get information about the GSM network and the network operator Example of reply Installation name Operator operator Band 900 MHz GSM roaming Yes GPRS roaming No Power on 1672 32 h Description SCADA With this status command it is possible to get information about the SCADA settings Example of reply Installation name SCADA code access code SCADA code ON Modbus address 231 Note SCADA is subject to access control if another access option than NONE has been selected GSMDATA With this status command it is possible to get information about the GSM data counters Example of reply Installation name SMS sent 4502 SMS received 37 Dial in 188 22 h Call back 44 09 h Counter time 1435 43 h Counter time in h min since last GSM counter reset The counters can be reset with the command RESETGSM GPRSSETTINGS With this status command it is possible to get information about the settings of the GPRS connection Example of reply Installation name APN Grundfos dk2 tdc MODBUSPORT 502 GENIPROPORT 49152 USERNAME PASSWORD AUTHENTICATION NORMAL CONNECTION SERVER GPRSROAMING ON SERVER 172 16 2 66 Note SCADA is subject to access control if ano
13. 4393 5533 Telefax 455 11 4343 5015 Bulgaria Grundfos Bulgaria EOOD Slatina District Iztochna Tangenta street no 100 BG 1592 Sofia Tel 359 2 49 22 200 Fax 359 2 49 22 201 email bulgaria grundfos bg Canada GRUNDFOS Canada Inc 2941 Brighton Road Oakville Ontario L6H 6C9 Phone 1 905 829 9533 Telefax 1 905 829 9512 China GRUNDFOS Pumps Shanghai Co Ltd 50 F Maxdo Center No 8 XingYi Rd Hongqiao development Zone Shanghai 200336 PRC Phone 86 21 612 252 22 Telefax 86 21 612 253 33 Croatia GRUNDFOS CROATIA d o o Cebini 37 Buzin HR 10010 Zagreb Phone 385 1 6595 400 Telefax 385 1 6595 499 www grundfos hr Czech Republic GRUNDFOS s r o Cajkovsk ho 21 779 00 Olomouc Phone 420 585 716 111 Telefax 420 585 716 299 Denmark GRUNDFOS DK A S Martin Bachs Vej 3 DK 8850 Bjerringbro Tif 45 87 50 50 50 Telefax 45 87 50 51 51 E mail info GDK grundfos com www grundfos com DK Estonia GRUNDFOS Pumps Eesti O Peterburi tee 92G 11415 Tallinn Tel 372 606 1690 Fax 372 606 1691 Finland OY GRUNDFOS Pumput AB Mestarintie 11 FIN 01730 Vantaa Phone 358 0 207 889 900 Telefax 358 0 207 889 550 France Pompes GRUNDFOS Distribution S A Parc d Activit s de Chesnes 57 rue de Malacombe F 38290 St Quentin Fallavier Lyon T l 33 4 74 82 15 15 T l copie 33 4 74 94 10 51 Germany GRUNDFOS GMBH Schl terstr 33 40699 Erkrath Tel
14. 50 an installation name of maximum 30 characters The name will then be put in front of all messages from the CIM 250 If a name consists of more than 30 characters it will be shortened automatically The CIM 250 will acknowledge the change with this message Installation name NAME New installation name stored The installation name can be deleted by storing an empty installation name The CIM 250 will send this message NAME Installation name cleared Default setting Empty English GB 89 usii65ua Description HEARTBEAT hour of day day of week week on lt day of When this function is activated the CIM 250 regularly sends an SMS in form of a STATUS1 message to all numbers in the phone number list For further information about the STATUS1 message see section 4 Status commands HEARTBEAT is a CIM 250 configuration command that can be used to set at which hour of the day and on which weekdays the message is to be sent lt hour of day gt OFF 0 1 2 24 1 is 1 00 o clock AM 12 is noon and 0 or 24 is midnight OFF disables the function lt day of week gt ALL MON TUE WED THU FRI SAT SUN If ALL is selected the message will be sent every day If the hour of day is set to OFF the parameter day of week will be ignored and can be omitted Note It is possible to select more than one specific day if they are separated by commas The CIM
15. 5F 5 21 15 Higashi gotanda Shiagawa ku Tokyo 141 0022 Japan Phone 81 35 448 1391 Telefax 81 35 448 9619 Korea GRUNDFOS Pumps Korea Ltd 6th Floor Aju Building 679 5 Yeoksam dong Kangnam ku 135 916 Seoul Korea Phone 82 2 5317 600 Telefax 82 2 5633 725 Latvia SIA GRUNDFOS Pumps Latvia Deglava biznesa centrs Augusta Deglava iela 60 LV 1035 Riga T lr 371 714 9640 7 149 641 Fakss 371 914 9646 Lithuania GRUNDFOS Pumps UAB Smolensko g 6 LT 03201 Vilnius Tel 370 52 395 430 Fax 370 52 395 431 Malaysia GRUNDFOS Pumps Sdn Bhd 7 Jalan Peguam U1 25 Glenmarie Industrial Park 40150 Shah Alam Selangor Phone 60 3 5569 2922 Telefax 60 3 5569 2866 Mexico Bombas GRUNDFOS de M xico S A de Boulevard TLC No 15 Parque Industrial Stiva Aeropuerto Apodaca N L 66600 Phone 52 81 8144 4000 Telefax 52 81 8144 4010 Netherlands GRUNDFOS Netherlands Veluwezoom 35 1326 AE Almere Postbus 22015 1302 CA ALMERE Tel 31 88 478 6336 Telefax 31 88 478 6332 E mail info_gnl grundfos com New Zealand GRUNDFOS Pumps NZ Ltd 17 Beatrice Tinsley Crescent North Harbour Industrial Estate Albany Auckland Phone 64 9 415 3240 Telefax 64 9 415 3250 Norway GRUNDFOS Pumper A S Str msveien 344 Postboks 235 Leirdal N 1011 Oslo TIf 47 22 90 47 00 Telefax 47 22 32 21 50 Poland GRUNDFOS Pompy Sp z ul Klonowa 23 Baranowo k Poznania PL 62 081
16. 8 C write this command ANALOGOUT 5 8 The resulting voltage at AO1 will be 5 8 rangemin ranges FANGEmin 10 V 2 36 V Taking the scaling range and resolution into consideration the value is mapped as precisely as possible and sent to the analog output of the IO 270 A small rounding deviation may occur The CIM 250 will send an acknowledgement in form of an IOSTATUS message to the phone from which the SMS command was sent If value is not a legal floating point number for instance if it contains illegal characters the CIM 250 will send a negative acknowledgement ANALOGOUT Illegal command parameter Must be a number If value is outside the scaling range the 250 will send a negative acknowledgement ANALOGOUT Illegal command parameter Must be inside scaling range If an IO 270 is incorrectly installed or the connection is faulty the CIM 250 will send a negative acknowledgement ANALOGOUT IO 270 module not present 26 RELAYOUT lt ON OFF gt Control command for the output relay ON means that the relay is in its activated state Terminal NO closed terminal NC open The ON or OFF value is written to Modbus register 01202 SetRelayOut with the values ON 1 and OFF 0 The CIM 250 will send an acknowledgement in form of an IOSTATUS message to the phone from which the SMS command was sent If the argument differs from ON or OFF the CIM 250 will send a
17. GRUNDFOS INSTRUCTIONS CIM 250 SMS commands Installation and operating instructions supplement be M GRUNDFOS X 89 usuBu3 English GB Installation and operating instructions Original functional profile and user manual CONTENTS Page 1 Symbols used in this document 2 2 General description 3 2 1 CIU 251 4 3 Configuring the CIM 250 5 3 1 Basic configuration 5 3 2 Configuration for monitoring and control via SMS 6 3 3 Configuration for GSM call up connection 12 3 4 Configuration for GPRS connection 13 4 Status commands 15 5 Control commands 19 5 1 CIM 250 19 5 2 Grundfos product 19 6 Messages from the CIM 250 22 6 1 No connection to product 22 6 2 No mains supply using battery 22 6 3 Change GSM module battery 22 6 4 GSM module battery low 22 7T Additional SMS functionality of the CIU 251 23 7 1 Introduction 23 7 2 Configuration of IO 270 signal names 24 7 3 Configuration of IO 270 signal scaling 24 7 4 10 270 operation 25 7 5 Self triggered IO event messages 26 8 Overview of commands 28 8 1 Configuration commands for the CIM 250 28 8 2 Status commands for the CIM 250 29 8 3 Control commands for the CIM 250 29 8 4 Status commands for the product 29 8 5 Control commands for the product 30 8 6 IO 270 related configuration commands 30 8 7 IO 270 related status commands 31 8 8 IO 270 related control commands 31 1 Symbols used in this document Notes or instructions that make the job Note easi
18. INGS English GB 89 usii65ua Description SMSALARM ON OFF With this configuration command it is possible to enable or disable the transmission of alarm messages from the product in form of a STATUS 1 message to all numbers in the phone number list For further information about the STATUS message see section 4 Status commands The CIM 250 will acknowledge the change with this message SMSALARM changed to ON OFF Example of alarm message for a Hydro MPC booster system Installation name ALARM APPEARED Water shortage 214 Setpoint 78 Act setpoint 4 2 bar Act value 4 0 bar Stopped due to alarm If the function is enabled a message will also be sent when the cause of the alarm has disappeared and the product has returned to normal state The message content will be the same the message will however read ALARM DISAPPEARED To see the setting use the command GSMSETTINGS Default setting ON SMSWARN ON OFF With this configuration command it is possible to enable or disable the transmission of warning messages from the product in form of a STATUS 1 message to all numbers in the phone number list For further information about the STATUS1 message see section 4 Status commands The CIM 250 will acknowledge the change with this message SMSWARN changed to ON OFF Example of warning message for a Hydro MPC booster system Installat
19. PRESS This command sets the Grundfos product to control mode Constant pressure PROPPRESS This command sets the Grundfos product to control mode Proportional pressure AUTOADAPT 20 This command sets the Grundfos product to control mode AUTOADAPT ul z o2 35 x zz ipti Command E Es 3 Q Description 3 ui slo 5 m gt gt 2 2 u o2 r r szo This command makes the Grundfos product simulate an ALARMSIM alarm with an event code If the product supports the alarm lt gt selected and SMSALARM is set to ON it will react accordingly for instance by sending an alarm message Only 2000 Only MAGNA Example 1 The CIM 250 has been configured to access option CODE and the access code has been set to 8977 An alarm can be reset with this command 8977 RESETALARM Example 2 The number of your mobile phone is in the phone number list of the CIM 250 and the access option is BOTH default setting The setpoint can be changed to 4 5 m with this command SETPOINT 4 5 Note that the unit of the setpoint is not to be written as a part of the command parameter as it is implicitly given by the scaling unit of the feedback value This command makes the Grundfos product simulate a WARNSIM warning with an event code If the product supports the code warning selected and SMSWARN is set to ON it will react ac
20. The CIM 250 GSM module replies with information about the status of the IO 270 The measured values are as reported by the IO 270 device Installation name AI 87 1 if used as DI1 sensor if sensor signal fault Reg 01211 AI2 if used as 012 sensor error if sensor signal fault Reg 01212 TI1 48 4 C sensor error if sensor signal fault Reg 01213 DI1 if used as AI DI2 On if used as AI2 DI3 Off DI4 On A01 55 6 Using default 0 100 scaling in this example DO1 On Terminal NO closed terminal NC open IOSMS On IO event triggered SMS is enabled This example assumes that user defined signal names section 7 2 or analog signal scaling section 7 3 has not been configured Note If signal names or analog signal scaling has been configured the reply to IOSTATUS could e g look like this Installation name 11 Tank pressure 4 59 bar if used as 011 sensor if sensor signal fault Reg 01211 AI2 Tank outlet 34 2 m3 h if used as 012 sensor if sensor signal fault Reg 01212 TI1 Air temperature 5 6 C TI1 scaling is always 50 204 C DI1 if it is used as Al1 DI2 if itis used as Al2 DI3 Burglar alarm Off DI4 Door switch Off AO1 Cooling fan 55 6 Using default 0 100 scaling in this example DO1 Light switch On Terminal NO closed terminal NC open IOSMS On IO event trigge
21. access option is not LIST as this would leave the CIM 250 unaccessible and require a hardware reset press reset button for five seconds followed by a reconfiguration For further information about hardware reset see installation and operating instructions for the CIM 2XX GSM module Description DELNUMBER phone number ALL With this configuration command it is possible to delete a number in the CIM 250 phone number list If the number exists it will be deleted and the CIM 250 will acknowledge the change with this message DELNUMBER phone number deleted from the phone number list The message will be sent to both the sender of the command and to the phone number which has been deleted If the parameter is omitted the phone number of the sender will be deleted If the parameter is ALL all phone numbers will be deleted and the CIM 250 will send this message DELNUMBER Phone number list empty To see the phone number list use the command LIST Note If all phone numbers are deleted make sure that the access option is not LIST as this would leave the CIM 250 unaccessible and require a hardware reset press reset button for five seconds followed by a reconfiguration For further information about hardware reset see installation and operating instructions for the CIM 2XX GSM module NAME installation name With this configuration command it is possible to give the CIM 2
22. and TI1 The three monitor level values are not available on Modbus value 0 0 100 0 as default if no user defined scaling is used See section 7 3 If analog signal scaling is used for AO1 see section 7 3 the scaling must also be used when specifying the signal value to send to AO1 Example The analog output signal range has been configured to 0 50 m3 h To get a monitor level of 35 m h write SETAILILEVEL 35 The CIM 250 will send this message to the phone from which the SMS command was sent SETAIILEVEL Analog input 1 level set to value alpha string The alpha string represents the unit If value is not a legal floating point number for instance if it contains illegal characters the CIM 250 will send a negative acknowledgement SETAIILEVEL Illegal command parameter Must be a number If value is outside the scaling range the CIM 250 will send a negative acknowledgement SETAIILEVEL Illegal command parameter Must be inside scaling range If an empty argument is used the monitor level will be reset to its factory default value equalling the maximum range of the input 100 96 Configuring monitor levels is possible whether the IO 270 is present or not as long as the command syntax is correct If the command parameter is illegal or missing the CIM 250 will send a negative acknowledgement IOSMS Illegal command parameter Must be ON or OFF When self triggered IO event messa
23. cordingly for instance by sending a warning message 21 English GB 89 usil65ua 6 Messages from the CIM 250 The CIM 250 will send messages in case of faults or other special conditions in the module itself These messages do not depend on the Grundfos product They can be enabled disabled with the command SMSALARM ON OFF gt If SMSALARM is set to ON they will be sent to all numbers in the phone number list Note No message will be sent if the phone number list is empty for instance if the module has not been initialised The message is triggered by an event If the CIM 250 is switched off and on the battery must be removed it will send the message again if the cause of the message still exists 6 1 No connection to product If the communication between the CIM 250 and the Grundfos product is interrupted for more than one minute the CIM 250 will send this message to all numbers in the phone number list Installation name GSM module error No connection to product Note If the cause of the interruption is the fact that the power supply to the product was interrupted the CIM 250 will send this message instead No mains supply using battery See below 6 2 No mains supply using battery If the CIM 250 detects that it is being supplied from the battery it will send this message to all numbers in the phone number list Installation name GSM module error No mains supply using battery
24. d and one of the limits is reached the CIM 250 will send this message SMS alarm warning limit of 10 identical messages per day has been reached or SMS alarm warning limit of a total of 100 messages per day has been reached To see the setting use the command GSMSETTINGS Default setting ON SETCODETEXT event code text Alarms and warnings events from a connected product are normally sent to all phone numbers in the phone number list in form of a STATUS1 message containing the standard English text belonging to the event code in question The user can configure own texts for up to ten different event codes This is done one at a time with this configuration command The event code texts to be changed are changed one by one by repeating the command Leaving out the name argument will reset the text of the event code in question to the original text Leaving out both arguments will reset all event code texts to their original text Parameters event code The event code in question text The new text for the event code If this field is left empty the text of the event code will be reset to its factory default text If both parameter fields are left empty all event code texts will be reset to their factory default text Example SETCODETEXT 3 Alarm button pressed The CIM 250 will acknowledge the command with this message SETCODETEXT Text for event code 3 changed to Alarm button pressed E
25. de and to change the setpoint The CIM 250 will acknowledge the change by sending a STATUS1 message to the mobile phone from which the command was sent Changing of control mode operating mode or setpoint for a pump will automatically set the pump to remote controlled operation These settings will be saved in the CIM 250 module in case of power cuts They can also be changed via a GSM call up connection or a GPRS connection The latest change of settings will apply Changes via GSM call up connection or GPRS connection however are not saved in the CIM 250 in case of power cuts Note The commands depend on the Grundfos product If the command is not supported by the product the product will ignore the command and the CIM 250 will send this message command Command not supported by connected device type Note The commands are all subject to access control if another access option than NONE has been selected Note Control of Hydro MPC via CIM 250 requires this setting via the control panel of the CU 351 Settings Secondary functions Control source Select From bus For further information see the installation and operating instructions for Hydro MPC on WebCAPS 89 usua Command E pumps UPE MAGNA Hydro MPC Hydro Multi E MP 204 CIU 252 Description RESETALARM Resets an alarm or a warning in the Grundfos product if the fault no longer exists The product will try to restart REMOTE
26. eet the requirements If the CIM 250 is to be re initialised at a later time for instance if you have forgotten the access code press the reset button on the module for at least five seconds This resets settings to the default settings The command INIT must be sent to the CIM 250 again For further information about hardware reset see installation and operating instructions for the CIM 2XX GSM module With this configuration command it is possible to set whether the CIM 250 is to accept roaming or not The CIM 250 will acknowledge the change with this message ROAMING changed to ON OFF ROAMING ON OFF If roaming is set to OFF this will apply to both GSM SMS and GPRS communication If roaming is set to ON this will apply to GSM and SMS communication whereas roaming for GPRS communication will only be allowed if GPRSROAMING has also been set to ON Default setting ON English GB 89 usua 3 2 Configuration for monitoring and control via SMS Command Description ACCESS access option Select the access option with this configuration command LIST Only numbers in the CIM 250 phone number list can send configuration and control messages CODE The 4 digit access code must be used in front of all configuration and control commands BOTH Both LIST phone number list and CODE access code can be used for access control Only one is required to get access NONE Th
27. er and ensure safe operation 2 General description The CIM 250 can be used as an SMS interface for control and monitoring of Grundfos products e g E pumps and Hydro MPC booster systems from a mobile phone Using simple SMS messages it is for instance possible to start and stop the pump system change the setpoint and get status of important pump system data and alarm and warning messages SMS messages which can be sent by the user and interpreted by the CIM 250 are called commands The general syntax of commands is access code command parameter parameter 1 indicates a field which is only used in certain cases indicates a mandatory field All texts sent to the CIM 250 are in English and cannot be changed 10 alarm warning texts as well as the name and scaling of the CIU 251 input output signals can be user configured All other texts sent from the CIM 250 are fixed and written in English This manual shows text message communication with mobile phones with the font Courier or in quotation marks English GB 89 usii65ua 2 1 CIU 251 The CIU 251 consists of a CIM 250 module and an IO 270 board mounted in a CIU box The IO 270 adds I O features to the functionality of the CIM 250 See also section 7 Additional SMS functionality of the CIU 251 Command Description access code Four numerical characters between 0 and 9 It will be ignored if the access code has not
28. ere is no access control All commands can be sent from a mobile phone without access control Before carrying on the configuration wait until the CIM 250 has acknowledged the change with this message ACCESS changed to access option Default setting BOTH CODE access code With this configuration command it is possible to change the 4 digit access code Before carrying on the configuration wait until the CIM 250 has acknowledged the change with this message CODE changed to access code ADDNUMBER phone number With this configuration command it is possible to add a number to the CIM 250 phone number list The number must be of international format with followed by the country code and the local number In the case of local numbers and the country code are not required Up to four numbers can be stored When a number has been added the CIM 250 will acknowledge the change with this message ADDNUMBER phone number added to the phone number list The message will be sent to both the sender of the command and to the phone number which has been added If the parameter is omitted the phone number of the sender will be added When the CIM 250 has been initialised only the number of the mobile phone used for initialisation will be in the internal phone number list of the module To see the phone number list use the command LIST Note If all phone numbers are deleted make sure that the
29. ges are enabled messages like the examples below will be sent when a digital input changes its state or an analog input value crosses the monitor level is now On high DI3 is now Off low DI4 is now Off low 11 exceeds level AI2 exceeds level TI1 falls below level GETLEVELS Status command for displaying the monitor values of AI AI2 andTI1 Below is an example of a reply Installation name Monitor level 11 8 bar Monitor level AI2 35 m h Monitor level TI1 3 5 C The levels will be shown as scaled as above if the input is scaled 100 Monitor level 5096 Hysteresis fixed 10 c Tim Send Send SMS SMS Fig Event messages triggered by the monitor level of an analog input 27 English GB 89 usuBu3 8 Overview of commands 8 1 Configuration commands for the CIM 250 Command Description Sed Basic configuration INIT access code Initialisation of the CIM 250 ROAMING ON OFF Enabling disabling of roaming ON Monitoring and control via SMS ACCESS LIST CODE BOTH NONE Change of access option BOTH STATUSPROTECT ON OFF Setting of status protection OFF CODE access code Change of access code ADDNUMBER phone number Adding a phone number DELNUMBER phone number ALL Deleting a phone number NAME installation na
30. he IO 270 adds 1 0 features to the functionality of the standard CIU 250 See fig 2 This functional profile describes the additional Modbus registers relating to the IO 270 CIM 250 IO 270 5 MO GENIbus Grundfos product TMO5 7742 1613 Fig 1 CIM 250 and IO 270 built into a CIU 251 and connected to a Grundfos product via GENIbus Relay Analog input 1 output or digital input T 001 Analog input 2 or digital input 2 AI2 DI2 AO1 ETT Tr output Digitalinput3 g DI3 10270 Digital input 4 vigital input Temperature gt TM 2 Pt100 Pt1000 J1 J2 J3 J4 Ni Signal configuration s Fig 2 IO 270 I O signals Jumpers are used to configure analog input signal types and selection between AI1 DI1 and AI2 DI2 The tables below show how to configure the analog and digital inputs using jumpers J1 J4 It also gives an overview of the options Details as how to connect sensors relays etc and the layout of the terminals can be found in the installation and operating instructions Multi purpose IO module in CIU 27X which is the IO 270 hardware manual Selection AI1 DI1 J1 J2 Signal Open Open Analog 0 10 V Open Closed Analog 0 20 mA Closed Open Analog 4 20 mA Closed Closed Digital default Selection AI2 DI2 J3 J4 Signal Open Open Analog 0 10 V Open Closed Analog 0 20 mA Closed Ope
31. ion it will be sent to all numbers in the phone number list When the time value has been set either manually with the command TIME or automatically from the network service the internal real time clock of the CIM 250 will work correctly as long as a power supply is present To see the settings use the command GSMSETTINGS Default setting OFF TIME day year hour month minute If the GSM network does not support time information for synchronising the internal real time clock of the CIM 250 this command can be used to supply the information Once synchronised the internal clock will run as long as the CIM 250 is powered or connected to its backup battery Parameters lt gt 2010 2100 lt month gt 1 12 lt day gt 1 31 lt hour gt 0 23 lt minute gt 0 59 If the setting has been done correctly the CIM 250 will send this message TIME Time has been set to lt year gt lt month gt lt day gt lt hour gt lt minute gt lt month gt A three letter truncation of month Example The command TIME 2010 5 6 9 30 results in this message TIME Time has been set to 2010 May 6 09 30 If any of the parameters are outside their specified range or missing the CIM 250 will send this message TIME Illegal or missing command parameter The real time setting only influences the heartbeat function To see the value of the internal real time clock use the command GSMSETT
32. ion name WARNING APPEARED Feedback sensor signal fault 171 Setpoint 78 Act setpoint 4 2 bar Act value 4 0 bar START from GSM If the function is enabled a message will also be sent when the cause of the warning has disappeared and the product has returned to normal state The message content will be the same the message will however read WARNING DISAPPEARED To see the setting use the command GSMSETTINGS Default setting ON STATUSPROTECT ON OFF 10 As default access control does not prevent status commands from being executed Only unauthorised configuration and control commands are blocked If access control is to be applied for all commands status protection this configuration command can be used to activate status protection To see the setting use the command GSMSETTINGS Default setting OFF Description SMSLIMIT ON OFF The same event message cannot be sent more than 10 times in a row within 24 hours This prevents the transmission of an unlimited stream of identical messages if the Grundfos product is in a condition where the same event appears and disappears continuously within a short period The total number of event messages is also limited to 100 within 24 hours The command activates or deactivates the two limitations The CIM 250 will acknowledge the change with this message SMSLIMIT changed to ON OFF If the limitations are activate
33. l 46 31 332 23 000 Telefax 46 31 331 94 60 Switzerland GRUNDFOS Pumpen AG Bruggacherstrasse 10 CH 8117 F llanden ZH Tel 41 1 806 8111 Telefax 41 1 806 8115 Taiwan GRUNDFOS Pumps Taiwan Ltd 7 Floor 219 Min Chuan Road Taichung Taiwan R O C Phone 886 4 2305 0868 Telefax 886 4 2305 0878 Thailand GRUNDFOS Thailand Ltd 92 Chaloem Phrakiat Rama 9 Road Dokmai Pravej Bangkok 10250 Phone 66 2 725 8999 Telefax 66 2 725 8998 Turkey GRUNDFOS POMPA San ve Tic Ltd Sti Gebze Organize Sanayi B lgesi Ihsan dede Caddesi 2 yol 200 Sokak No 204 41490 Gebze Kocaeli Phone 90 262 679 7979 Telefax 90 262 679 7905 E mail satis grundfos com Ukraine 01010 86 Ten 38 044 390 40 50 38 044 390 40 59 E mail ukraine grundfos com United Arab Emirates GRUNDFOS Gulf Distribution P O Box 16768 Jebel Ali Free Zone Dubai Phone 971 4 8815 166 Telefax 971 4 8815 136 United Kingdom GRUNDFOS Pumps Ltd Grovebury Road Leighton Buzzard Beds LU7 4TL Phone 44 1525 850000 Telefax 44 1525 850011 U S A GRUNDFOS Pumps Corporation 17100 West 118th Terrace Olathe Kansas 66061 Phone 1 913 227 3400 Telefax 1 913 227 3500 Uzbekistan 700000 1 5
34. l commands Control Command Description ANALOGOUT value Setting the value of analog output AO1 RELAYOUT lt ON OFF gt Operating the value of relay output DO1 Subject to alterations 31 English GB s luedwo so Argentina Bombas GRUNDFOS de Argentina S A Ruta Panamericana ramal Campana Centro Industrial Gar n Esq Haendel y Mozart AR 1619 Gar n Pcia de Buenos Aires Pcia de Buenos Aires Phone 54 3327 414 444 Telefax 454 3327 45 3190 Australia GRUNDFOS Pumps Pty Ltd P O Box 2040 Regency Park South Australia 5942 Phone 61 8 8461 4611 Telefax 61 8 8340 0155 Austria GRUNDFOS Pumpen Vertrieb Ges m b H GrundfosstraRe 2 A 5082 Gr dig Salzburg Tel 43 6246 883 0 Telefax 43 6246 883 30 Belgium N V GRUNDFOS Bellux S A Boomsesteenweg 81 83 B 2630 Aartselaar T l 32 3 870 7300 T l copie 32 3 870 7301 Belarus 220125 11 56 Ten 7 375 17 286 39 72 286 39 73 7 375 17 286 39 71 E mail minsk grundfos com Bosnia Herzegovina GRUNDFOS Sarajevo Trg Heroja 16 BiH 71000 Sarajevo Phone 387 33 713 290 Telefax 387 33 659 079 e mail grundfos bih net ba Brazil BOMBAS GRUNDFOS DO BRASIL Av Humberto de Alencar Castelo Branco 630 CEP 09850 300 S o Bernardo do Campo SP Phone 55 11
35. me gt Selection of installation name cavers of day day of gt Setting of heartbeat value OFF TIME lt year gt month day hour minute Setting of time SMSALARM ON OFF Setting of SMS alarms ON SMSWARN ON OFF Setting of SMS warnings ON SMSLIMIT ON OFF Setting of event message limit ON Seve nt code sexs Setting of user defined code texts GSM call up connection SETSCADACODE access code Setting of SCADA access code SCADACODE ON OFF Setting of SCADA access code OFF MODBUSADDR 1 247 Setting of Modbus address 231 GPRS connection APN APN string Setting of APN USERNAME alpha numeric string Setting of GPRS login user name PASSWORD alpha numeric string Setting of GPRS login password AUTHENTICATION NORMAL SECURE Setting of GPRS authentication NORMAL CONNECTION SERVER CLIENT DISABLED gt Setting of connection mode SERVER GPRSROAMING ON OFF Setting of GPRS roaming OFF MODBUSPORT port number Setting of Modbus port number 502 GENIPROPORT port number Setting of GENIpro port number 49152 SERVER lt APN string IP address gt Setting of subsystem server SETGPRS lt APN gt Modbus port GENIpro port number gt user name gt password authentication connection GPRS roaming server If connection mode is CLIENT 28 Complete setting of GPRS 8 2 Status commands for
36. n Analog 4 20 mA Closed Closed Digital default 23 English GB 89 usii65ua 7 2 Configuration of IO 270 signal names You can change the default signal names Analog input 1 AI1 Digital input 1 DI1 etc The table below shows the commands for this purpose 7 3 Configuration of IO 270 signal scaling The default scale of analog readings of the IO 270 is 0 100 96 The scaling of each analog signal can be adjusted to the actual sensor using the commands in the table below Naming of 1 AI1NAME text Naming of Al2 AI2NAME lt text gt Scaling of Ai 18 lt value gt lt value gt alpha string gt Naming of TH FNAME Scaling of aj AI2SCALE lt value gt value Naming of DI1 DI1NAME lt text gt 9 lt alpha string gt Naming of DI2 DI2NAME text AO1SCALE lt value gt value 9 Scaling of AO1 alpha ion Naming of DI3 DI3NAME text P 9 Naming of 014 DIANAME text Naming of AO1 AO1NAME text Naming of DO1 DO1NAME text Example To change the name of AI1 use the command Al 1NAME followed by the new name in lt gt If the gt field is left empty the user name will be cleared and reset to the factory default name The CIM 250 will send one of these messages Positive acknowledgement of name change AI1NAME Changed to lt name gt Positive acknowledgement of name clearing AI1NAME User defined name cleared
37. negative acknowledgement RELAYOUT Illegal command parameter Must be ON or OFF If there is no IO 270 or the connection is faulty the CIM 250 will send a negative acknowledgement RELAYOUT IO 270 module not present 7 5 Self triggered IO event messages The event that a digital input changes its state from Off low to On high or from On high to Off low can be configured to trigger an SMS informing the user about the event Similarly when an analog input becomes higher or lower than a configurable monitor level this can also trigger an SMS We will refer to such an SMS as a self triggered IO event message This function can be enabled or disabled IOSMS ON OFF Configuration command for enabling or disabling the transmission of self triggered IO event messages Factory setting OFF The CIM 250 acknowledges the change with this message IOSMS changed to lt ON OFF gt Changing the status of IOSMS is possible whether the IO 270 is present or not as long as the command syntax is correct Seeing the status of IOSMS is only possible with IOSTATUS command though and only if IO 270 is present 011 gt On DI3 gt Off DI4 Door switch gt Off Al1 Tank pressure gt High Al2 gt High TI1 Water temperature gt Low SETAMLEVEL value empty Configuration command for the GSM module It is used to configure the monitor level for Al1 A similar command exists for AI2
38. nt code from connected product lt text gt Max 50 GSM 3 38 characters except LF CR ESC Codes 00h OAh ODh 1Bh 3Ah Automatic truncation will occur It is allowed for lt text gt to be empty lt alpha string gt Max 12 ASCII characters A Z a z Automatic truncation will occur It is allowed for lt alpha string gt to be empty Floating point value according to IEEE 754 but limited to lt value gt 5 digit precision e g x Xxxx etc Extra digits will be ignored E Empty field no argument There is no distinction between Note lowercase and uppercase letters in the commands 3 Configuring the CIM 250 Before the SMS functions of the CIM 250 can be used the CIM 250 must be configured using the SMS configuration commands in this section The commands are divided into four groups One group for basic configuration and three groups for the type of connection to be established Commands for basic configuration mandatory See section 3 1 Basic configuration Commands for configuration of the CIM 250 for monitoring and control via SMS See section 3 2 Configuration for monitoring and control via SMS 3 1 Basic configuration Commands for configuration of the CIM 250 for a GSM call up connection See section 3 3 Configuration for GSM call up connection Commands for configuration of the CIM 250 for a GPRS connection See section 3 4 Configu
39. ration for GPRS connection First carry out the basic configuration as it is common to all three types of connection and required for any installation Then carry out the configuration for the type of connection to be established The default setting will work in most cases See also section 8 Overview of commands Command Description The first time the CIM 250 is used it has to be initialised with this command The number of the mobile phone used for initialising the CIM 250 will be added to the internal phone number list of the module Access via commands can now take place from this number or by using the access code which must consist of four digits between 0 and 9 Before carrying on the configuration wait until the CIM 250 has acknowledged the change with this message INIT phone number added to the phone number list Access code access code If the CIM 250 has already been initialised it will send this message INIT Already initialised Note INIT access code When the command INIT has been carried out settings can only be changed from the phone number used for initialising the CIM 250 or with the selected access code in front of the command After initialisation the CIM 250 will use the default settings and in most cases it will not be necessary to change them See section 8 1 Configuration commands for the CIM 250 However please read the rest of this table and check that the default settings m
40. red SMS is enabled If there is no IO 270 or the connection to it is faulty the CIM 250 will send a negative acknowledgement IOSTATUS IO 270 module not present IOSCALING Command for status of signal scaling The CIM 250 module replies with information about the status of the analog signal scaling of the IO 270 Installation name 11 0 0 10 0 bar Indicating with if it is used as 011 AI2 20 0 80 0 C Indicating with if it is used as DI2 TI1 50 204 C This scaling is fixed and cannot be changed by the user AO1 0 100 The example shows the default factory scaling Signal Register Scale SMS 11 10223 10270_AnalogInput1 0 1 96 11 min 1 max AI2 10224 10270_AnalogInput2 0 1 96 Al2min Al2max 1 01201 SetAnalogOutput1 0 1 96 lt 1 AOA User defined signal scaling is used by the SMS interface but the Modbus register scaling is fixed 25 English GB 89 usii65ua ANALOGOUT value Control command for setting the value of AO1 The argument value 0 0 100 0 is default if no user defined scaling is used value is written to Modbus register 01201 10270_SetAnalogOut If analog signal scaling is used for AO1 it must also be used when specifying the signal value to send to AO1 See section 7 3 Example The analog output signal range has been configured to 20 40 C To change an analog output value to for instance 5
41. replaces the addressing mechanism The default Modbus address usually works fine but it can be changed with this command if required Default setting 231 MODBUSADDR 1 247 12 3 4 Configuration for GPRS connection To see the status use the command GPRSSETTINGS Command Description lt APN string Set the Access Point Name APN according to the information from your GPRS service provider Default setting Empty USERNAME alpha numeric string Set the user name for the APN according to the information from your GPRS service provider In many cases a user name will not be necessary Default setting Empty PASSWORD alpha numeric string Set the password for login to the APN according to the information from your GPRS service provider In many cases a password will not be necessary Default setting Empty AUTHENTICATION NORMAL SECURE Select this option for login to the APN according to the information from your GPRS service provider In many cases it will not be necessary to change the setting Default setting NORMAL CONNECTION SERVER CLIENT DISABLED The CIM 250 only supports connection mode SERVER or DISABLED DISABLED can be used as a simple way to disable the GPRS connection without removing the settings in the APN string Default setting SERVER GPRSROAMING lt ON OFF gt This command makes it possible
42. rundfos product by means of status commands See table below Apart from the commands LIST GPRSSETTINGS and SCADA the commands are not subject to access control unless STATUSPROTECT ON as they do not change anything in the CIM 250 or the Grundfos product Command Description GSMSETTINGS With this status command it is possible to see the configuration status of the CIM 250 Example of reply Installation name Configuration status Access control CODE Heartbeat At 12 00 Wed Roaming OFF SMS alarm ON SMS warning ON SMS limit ON TIME 2010 Mar 29 08 35 Status protection OFF LIST With this status command it is possible to see which numbers are in the CIM 250 phone number list The CIM 250 will send a message with all phone numbers Each number takes up a line Example of reply Installation name LIST 4520509988 4521190627 4522814495 If there are no numbers in the phone number list the CIM 250 will send this message Installation name LIST Phone number list empty Note LIST is subject to access control if another access option than NONE has been selected SIGNALLEVEL With this status command it is possible to get information from the CIM 250 about the detected signal strength of the GSM network Not detected 0 96 25 96 50 96 75 100 96 Example of reply Installation name GSM signal level Actual 100 Average 50 The actual value i
43. s the value read from the CIM 250 right now the average value is the average of the signal during the last hour Note Not all network operators support this service 15 English GB 89 usuBu3 Command Description STATUS1 STATUS2 With these status commands it is possible to get information from the CIM 250 about the Grundfos product The values measured are as reported from the Grundfos product The content of the message depends on the product type Example of STATUS1 message for a pump Installation name Setpoint 65 of 0 10 bar Act setpoint 6 5 bar Act value 5 2 bar START from GSM Control Const press Example of STATUS2 message for a pump Installation name Head 8 4 m Flow 24 m3 h Power 1830 W Performance 79 Energy 4570 kWh Hours 2568 h VERSION With this status command it is possible to get pieces of information such as the software version of the CIM 250 and the type of Grundfos product Example of reply Installation name CIM 250 V01 00 00 Telit 07 03 101 Hydro MPC booster IMEI 3570220010091936 IMSI 770008945629634 IMEI is the equipment identity number and IMSI is the subscriber identity number BATTERY With this status command it is possible to get information about the battery status if the CIM 250 is equipped with a battery optional Example of reply Installation name External voltage Yes Battery voltage 3 5 V Battery temp
44. ther access option than NONE has been selected If connection mode is CLIENT GPRSDATA With this status command it is possible to get information about the Modbus TCP status Example of reply Installation name Packets 374021 Received 196684 kb Sent 183427 kb Counter time 419 51 h gt Packets The sum of Modbus TCP and GENIpro TCP Counter time The time since the last GPRS counter reset The counters can be reset with the command RESETGPRS 17 English GB 89 usuBu3 Command Description GPRSSTATUS 18 With this status command it is possible to get information about the GPRS status Example of reply Installation name GPRS CONNECTED IP 172 16 1 30 Modbus Port 502 GENIpro Port 49152 Modbus addr 231 Socket 1 OPEN Socket 2 CLOSED Socket 3 CLOSED Socket 4 CLOSED Silence timeout 60 min Socket 1 3 Modbus TCP connection Socket 4 GENIpro TCP connection 5 Control commands 5 1 CIM 250 Command Description Resets GSM data counters The CIM 250 will acknowledge the change with this RESETGSM message RESETGSM GSM data counters reset English GB Resets GPRS data counters The CIM 250 will acknowledge the change with this RESETGPRS message RESETGPRS GPRS data counters reset 5 2 Grundfos product By means of the control commands in the table below it is possible to set the Grundfos product to run in the desired control mode and operating mo
45. xample SETCODETEXT empty empty The CIM 250 will acknowledge the command with this message SETCODETEXT Text for all event codes reset to factory text The text of any event code can always be requested with this command GETCODETEXT event code English GB 89 usua Command Description This is a status command used to read the text associated with an alarm warning code event code Example GETCODETEXT 3 GETCODETEXT event code The CIM 250 will acknowledge the command with this message GETCODETEXT Text for event code 3 Alarm button pressed user defined text The last parenthesis tells if the text is a user defined text or if it is the factory default text 3 3 Configuration for GSM call up connection To see the status use the command SCADASETTINGS Command Description Sets a four digit SCADA access code If SCADA access code protection is set to ON see below the SCADA access code has to be written in the Modbus register ScadaPinCode Reg 000011 SETSCADACODE access code gt before data can be written to the CIM 250 For the use of SCADA access code protection see the functional profile and user manual for the product in question Sets SCADA access code protection to ON or OFF SCADACODE ON OFF 2 id Default setting OFF Normally the Modbus address does not play any role in a GSM or GPRS network as the SIM card phone number or the assigned IP address

CIM 250 SMS commands

Contents

Download Pdf Manuals

Related Search

Related Contents