gds-8000 bioimaging system
Contents
1. Note For more specific information about the Thermal Printer refer to the Operation Manual supplied with the printer WWW UVP COM 18 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 The printer power cable should plug directly into the wall or a power strip The data cable for the printer is a 25 parallel connector This 25 pin connector will plug into the female equivalent in the back of the computer This plug looks identical to that of the Image Acquisition Board where you should have already plugged in the camera Do not plug this into the slot adjacent to the monitor plug or the video board will be rendered useless Find the open 25 pin female slot this is the printer port As soon as this port has been identified locate the Security Dongle supplied with the software package This will be a small key that will fit between the computer and the printer cable When you have secured this dongle onto the printer port on the back of the computer plug the printer cable directly into the back of the dongle Once the computer end of the cord is secured locate the other end and plug it into the designated port on the printer Plug in and secure the clips WWW UVP COM 19 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 Section 4 8 BIT MONOCHROME CAMERA A Camera 8 BIT MONCHROME 1 The camera power should plu2. 5 position Filter Control oo m m o Uu Master Darkroom Power Switch Darkroom Dor r gt J Fold Away Chemi Tray K Compression Door Lock L Sliding Transilluminator Drawer Note The transilluminator is powered from the inside of the darkroom which allows the transilluminator to be controlled from external darkroom switches 1 Unpack the EpiChemi Il Darkroom and Benchtop transilluminator from the packaging materials 2 Assemble the two together by placing the transilluminator on the sliding tray of the darkroom Plug the Transilluminator in by using the internal power cord found inside the darkroom WWW UVP COM 12 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 C Software Computer The computer power cable should plug directly into a power strip or surge protector Find and locate the mouse keyboard and other accessories plug in and secure all connections Start up the computer once all of the connections have been made and the power is attached Software Installation Windows 98 1 Insert the UVP software CD in to the CDROM drive to load the image acquisition software found on the LABWORKS CD Windows 98 should automatically detect and bring you to the SET UP OPTIONS menu of the software If this does not work double click on the main computer icon usually called My Computer on the desktop Then double click on the CD ROM
3. 452 6788 UK Technical Support 44 0 1223 420022 4 Then slide the camera into the c camera bracket with the serial numbers facing forward e Serial Numbers 5 Elevate the camera assembly 1 8 and screw the mounting bolts into the camera Tighten straighten and secure Make sure the zoom lens and the light sealing gasket are situated properly WWW UVP COM 23 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 C Zoom Lens Zoom lens features Components of the zoom lens are as follows 1 Top Ring f stop This ring controls how much light the camera will see tt 2 Middle Ring Zoom This ring controls the field of view that the camera will image M 3 Bottom Ring Focus This will adjust the sharpness of the image the camera will image I 4 Diopters A 2 diopter is included This is necessary to enable Auto Focus 5 Filters The colored filters will remove unwanted wavelengths from being passed through to the image The filters are attached by screwing on to the end of the zoom lens WWW UVP COM 24 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 Section 5 SYSTEM CHECK OUT A Camera Configuration The camera will need to be configured once the system is operational The settings are factory set on systems bought with computers Otherwise some necessary adjustments may be needed If the c
4. Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 D ACCESSORIES Printer and Security Dongle Unpack the Thermal Printer and place this alongside the computer The printer is supplied with a separate instruction manual giving full operation and service details The printer driver is preloaded on the computer You have been supplied with a printer cable that should be connected at one end to the security dongle provided with the software which is connected to the LPT1 parallel out port of the computer and into the Centronics port of the printer at the other end A power cable should be connected between the electrical supply and the printer Power ON OFF Press the switch at the top left hand corner of the front panel The indicator light glows while the power is on Loading Paper Ensure the power is ON Press the open close lever to open the paper door Place the paper roll in the printer ensuring that the thermosensitive side is up 4 Pull out the first 15 20cm of paper to remove any slack in the roll 5 Push the paper door closed Qmm PRINTER DRIVER INSTALLATION To add a printer to the GDS 8000 the procedure is as follows Go to the START menu SETTINGS PRINTERS Choose ADD PRINTER This will take you through the printer set up wizard When appropriate choose HAVE DISK Select BROWSE Select the appropriate operating system and choose O K Follow the wizard s instructions
5. assist you in any way possible How to use this manual The following compilation is intended to help the user install and upgrade their darkroom systems in a step by step procedure The first section will discuss setting up the computer hardware computer boards monitor printer Once you have completed that step we will guide you through your darkroom and camera system From there the manual will outline software installation including video board settings and acquisition software installation The final step is setting up the capture As there are several products available please make sure you are following the instructions for your particular system Important Features of your system 1 CCD Camera e GDS 8000 8 bit monochrome offers great image quality with varying focus and multiple darkroom options UV White Mini Darkroom EpiChemi 11 2 Computer e Minimum specifications e Standard 8 bit camera operation Pentium II processor or equivelant 1 GB Hard drive 16MBRAM in floppy drive CD ROM drive 8MB Video 3 LabWorks Software e Combines powerful image capture capability with sophisticated analysis options Acquire calibrate and quantitate molecular weights intensities mass and object counts on DNA RNA and Protein gels Slides and specimen selections Colony culture and microtiter plates Dot and Slot blots Films and Membranes WWW UVP COM 4 US Technical Support 1 800 452 6788 UK Technical
6. the Capture button to capture image If the image captured is not satisfactory adjust the integration tab and repeat steps 9 11 WWW UVP COM 27 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 Appendix A Troubleshooting Guide Can not capture Image When selecting the Camera Icon on the toolbar there is a tab named Signal tab which has an option called External Trigger please make sure this option is NOT checked The only way to capture image if this option is checked is to press any key on the keyboard this acts as the external trigger Can not view live preview or image shows red or gray Remove all PCI ISA or EISA boards the situation that we had arise within a PC came from a third party sound card which was an ISA board Macros become Disabled When naming a file to print do not name the file PRINT or else the Macros will be disabled When select live preview get an image of black dots on a white background Check your camera settings by clicking on the camera icon Make sure the appropriate camera driver is selected do not see a live preview through my camera Check to make sure you have power going to your camera and that all of your cables are properly connected Also make sure your aperture is opened all the way to get the most light in Appendix B Maintenance Cleaning Zoom or fixed lens gently wipe the glass surfaces with a lens cloth do not use any abra
7. GDS 8000 Image Acquisition and Analysis System Set Up and User Manual SUVP BiolMAGING SYSTEMS GDS 8000 Image Acquisition and Analysis System Set Up and User Manual UVP Inc 2066 W 11 Street Upland CA 91786 800 452 6788 or 909 946 3597 Fax 909 946 3597 E Mail uvp uvp com WWW UVP COM SUVP Ultra Violet Products Ltd Unit 1 Trinity Hall Farm Estate Nuffield Road Cambridge CB4 1TG UK 44 0 1223 420022 Fax 44 0 1223 420561 E Mail uvp uvp co uk http www uvp com 81 0145 02 2 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 GDS 8000 BIOIMAGING SYSTEM Table of Contents 1 Introduction 2 Safety Information 3 GDS 8000 System Set Up A Camera Stand 1 Assembly Adjustment B Darkrooms 1 Mini Darkroom 2 UV White Darkroom 3 EpiChemi Il Darkroom C Software D Accessories 4 8 bit monochrome camera A Camera B Assembly instructions C Zoom Lens 5 System Check Out A Camera configuration B Focusing 6 Image Capture Methodologies A Non Fluorescent Gels B Fluorescent Gels Appendix A Troubleshooting Appendix B Maintenance WWW UVP COM US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 SECTION 1 Introduction Congratulations You have selected the most comprehensive Biolmaging Systems GDS available on the market today UVP strives to keep up with the advancements in technology and wishes to
8. InstallShield Wizard WWNW UVP COM 13 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 2 Click on the button with the camera icon to select capture driver installation Click NEXT Exit all open programs 3 The capture driver needs to be installed into the LABWORKS folder If the listed location is not the correct folder click BROWSE and locate the LABWORKS folder Once you have found the correct folder click OK and then NEXT The driver will be installed 4 When installation is complete click on FINISH Windows NT 1 First load the software found on the LABWORKS CD This is done by loading the UVP software CD Win NT should initially detect and bring you to the SET UP OPTIONS menu of the software If this does not work go to the My Computer icon and double click Double click on the CD ROM drive The dialogue box should now appear 2 Install the software first by double clicking the LABWORKS icon This will take you through an INSTALL SHIELD WIZARD and guide you through installation 3 Choose next and follow the instructions closely The destination directory should be LABWORKS Click on Next Selection of Installation Type should be Typical Program folders should be LABWORKS4 choose NEXT This will go through LABWORKS Setup After this is completed the dialogue box reads Installation completed Would you like to install the Capture Kit now Choose Yes This takes you through anoth
9. OL PANEL and double click on MULTIMEDIA Goto the DEVICES tab and make sure Add unlisted or update drivers is highlighted and choose OK Browse at the Install Drivers window double click on C LabWorks WinNT Click OK until the Install Driver box reads C LabWorks Win NT Click OK Add unlisted or updated drivers Select Capkit Video Choose OK until finished estart the computer for these changes to take place Co WWW UVP COM 15 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 Installing the Capture Kit Board Note The Capture Kit Board is relatively easy to install If however you have reservations about installing it we recommend that you ask an experienced technician to do so If someone is not available call UVP technical support for further instructions 1 Be sure the power to your computer monitor and other peripheral devices are turned off You can cause damage to the components in your computer if you attempt to remove or insert boards with the power on Ground yourself to remove static electricity Static electricity can cause damage to your system components To discharge your body s static electricity touch a grounded surface This might be a grounding mat or grounding wrist strap Or before unplugging the computer power cord you can usually ground yourself by touching any part of the system s bare metal unpainted chassis Discharge st
10. Support 44 0 1223 420022 For EpiChemi Il Darkroom customers 4 EpiChemi Il Darkroom e Overhead 254 nm UV 365 nm UV and fluorescent white light e Enables the user to view the setup of the experiment in the darkroom while the darkroom door is open e Concealed viewer with UV blocking safety glass e Enables the user to view the experiment while in progress while protecting from UV exposure e Completely light tight darkroom e Allows for best analysis of experiments under low levels of phosphorescence e Retractable sliding transilluminator tray e Allows for easier facilitation of experiments e Five Position Filter Wheel e The filter wheel allows the user to select the specific bandpass wavelengths for the experiments the researcher would like to view This enables the user to increase the contrast and optimize the view of their experiments under different excitation wavelengths e 1 stained glass bandpass filter e dichroic interference filters for greater contrast e 1 Visible White light pass filter WWW UVP COM 5 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 SECTION 2 Safety Information Warning All UVP High Performance Transilluminators are powerful sources of Ultraviolet UV radiation that can cause damage to unprotected eyes and skin Be sure all personnel in the area are properly trained and protected before operating any unit that uses UV radiation It is further recommend
11. amera is not working properly Click on the camera icon Go to SETUP Make sure the type of camera is correct either NTSC or PAL CONFIGURE Make sure the correct camera is selected Check by clicking on START PREVIEW If the camera is still not working make sure that the driver for the video board has been installed properly mo Focusing e Turn on the white lights in the darkroom e Inserta printed piece of text with black and white lettering e Open LabWorks and click on the Camera Icon Video Digital Capture e Select live preview e Locate the f stop adjustment top lens ring and turn it counterclockwise until light is seen on the image e f you have a zoom lens locate the zoom adjustment middle lens ring and turn it clockwise so the image is as large as possible Note image will in most cases not be in focus If you have a fixed lens there is no need for adjustment e Locate the Focus adjustment the bottom ring and turn it until text appears clear and in focus e Adjust the f stop again to the correct amount of light which will make the blacks appear black and the whites appear white Note once the camera is in focus you may adjust the zoom without losing the focus WWW UVP COM 25 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 Section 6 Image Capture Methodologies A Non Fluorescent Gels Protein Gels Transmitted White Light Coomassie Blue S
12. atic electricity periodically while installing your Capture Kit Board Unplug the computer from its power outlet This will ensure that no power is available to the computer while you are exchanging boards Note however that you will no longer be able to use the computer chassis for discharging static electricity WWW UVP COM 16 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 4 To remove the computer cover remove the screws from the back of the case and slide the case off the computer Note A tower shaped computer is illus trated here If you have a desktop computer the motherboard is on the bottom rather than the side as shown in the next picture 5 Install the Capture Kit board into the PCI slot Take the new board out of the anti static bag Hold it by the edges to prevent damage to the components or the edge connectors the gold colored fingers that extend from the board Still holding it by its edges gently but firmly seat the fingers into the PCI slot Avoid touching the fingers themselves or any component part on the board When the board is seated in the slot secure the card to the chassis with the screw provided Place the VGA board you just removed into the anti static bag for protection Replace the computer cover by sliding the cover back into place and use the screws that you removed in Step 5 to refasten it onto the chassis WWW UVP COM 17 US
13. chnical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 4 With the camera facing the baseboard insert the bottom side of the square into the bottom of the recessed square on the camera arm Push in It should snap and secure into place ADJUSTABLE CAMERA TRIANGLE 2 in the picture C above 1 Place the triangle onto the Adjustable Camera Arm J and tighten the bolt Position the camera lens down and serial numbers facing out Reach around locate and tighten the securing bolt of the camera to the mount Adjust as necessary B Darkrooms The GDS 8000 system is a flexible system allowing users to choose from 3 darkroom options to use alongside an 8 bit non cooled CCD camera The Mini Darkroom is designed to digitally document test results within the laboratory By placing a benchtop style transilluminator beneath the darkroom you are able to capture low light fluorescent and visibly stained media of various types with brightness and clarity The UV White Darkroom is designed to digitally document results within the laboratory By placing either a standard format UV White or a high performance transilluminator beneath the darkroom you are able to capture low light level media of various types with brightness and clarity The UV White darkroom allows for use with the UV White combination and larger transilluminators The EPICHEMI II Darkroom is designed specifically for low light and fluorescence ima
14. drive The installation wizard will run the installation program now 2 The installation dialogue box will appear 3 Install the software first by double clicking on either the LABWORKS icon This will take you through an Install Shield Wizard and guide you through installation 4 Choose NEXT and follow the instructions closely The destination directory should be LABWORKS 5 Click on NEXT 6 The Installation Type should be TYPICAL Program folders should be LABWORKS4 choose NEXT 7 This will go through the LABWORKS or Setup After this is completed the dialogue box will prompt you with Installation completed Would you like to install the Capture Kit now Choose YES 8 This takes you through another Install Shield Wizard Under the dialogue box WELCOME click on BROWSE 9 Choose the folder LABWORKS that you installed the software in 10 Choose OK and then NEXT This will install the Pro Series MV Capture Kit 11 When installation is complete click on FINISH 12 The computer will ask you if you would like to reboot the computer for the changes to take effect Select YES and allow the computer to reboot in order for the desired software to be operational If you need to install the Capture Driver only 1 Insert the LABWORKS CD and allow it to autorun If your computer does not take you to the InstallShield Wizard double click on your main computer icon typically My Computer and select the CD ROM drive to run the
15. ed that the transilluminator be installed and operated in a darkroom where access and exposure is limited while the unit is in operation If a darkroom is unavailable UVP offers a wide selection of darkrooms or a shroud which provide protection from accidental exposure For your safety and for the safety of those around you the transilluminator in a UVP darkroom is controlled through the darkroom and each darkroom is equipped with a safety switch that controls the power to the transilluminator to prevent accidental exposure Each transilluminator is shipped with an ultraviolet blocking cover Even though the cover blocks out the UV radiation emitted by the unit we recommend the usage of UV blocking eyewear for additional protection WWW UVP COM 6 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 Section 3 GDS 8000 System Set Up IF YOU RECEIVED YOUR BIOIMAGING SYSTEM WITH A COMPUTER DIRECTLY FROM UVP PLEASE SKIP TO SECTION 4 DARKROOM AND CAMERA SYSTEMS A CAMERA STAND Crank for vertical adjustment Setscrew for vertical adjustment Crank for adjustment of the camera bracket Setscrew for camera bracket Camera platform with rubber lining and line pattern for correct positioning of the camera Ya camera screw adjustment screws Sliding carrier Camera bracket Adjustable camera arm mooo r z al H un unm LUNA m xw 2 WWW UVP COM 7 US Technical Suppor
16. er Install Shield Wizard Under the dialogue box Welcome click on Browse 8 Choose the directory LABWORKS that you originally installed the software in Choose OK and then NEXT This will install the Pro Series MV Capture Kit 9 When installation is complete click on FINISH ome N If you need to install the Capture Driver only Click on the BROWSE button Change the lookup file drive designation to the CD ROM drive Click on the CAPTURE FOLDER Click on DISK 1 Chose Winnt40 Run OEMSETUP Click OK 3 times YES you wish to proceed The display properties window should still be open 10 Change the color palette setting to 16777216 colors 11 Change the desktop area to 1024x768 recommended 12 Click on APPLY 13 Do not restart gt WWW UVP COM 14 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 14 Click on START 15 Click on SETTINGS 16 Click on CONTROL PANEL 17 Select MULTIMEDIA 18 Choose DEVICES tab 19 Click on the ADD button 20 Highlight the UNLISTED OR UPDATED driver then click ok 21 Install driver window 22 Click BROWSE and double click on C 23 Double click on LABWORKSA folder then double click on WinNT folder and click OK twice 24 Click OK with the listed driver Close all windows and reboot the computer For Win NT one further configuration is required 1 Updating the Capture Kit drivers 2 to START SETTINGS CONTR
17. g directly into the back of the computer Locate the camera cable This will have a 25 pin male parallel connector on one end a BNC connector an 8 pin connector as well as 2 open wires on the other end The BNC video connector plugs into the video socket on the camera 8 pin connector connects into the AUX port on the camera Loosen the two screws to the right of the video port Insert the power cables and tighten the screws Be sure the cables do not wiggle loose Once these connections are secure plug the other end into the Image Acquisition Board This 25 female connector on the computer is adjacent to where the monitor cord is plugged in If you purchased a computer with your system you have completed hooking up your camera Please proceed to the Camera Assembly section Power Cables plug either wire into either slot Video Cables POWER LAMP dJar 1 UNE LOCH SECT AS SETUP LAMP Rear Panel WWW UVP COM 20 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 The Camera you have purchased comes equipped with an internal power supply that should be installed in the computer as follows 2 Turn off and unplug the computer and any peripherals 3 Remove protected plate and insert power supply into the open slot 4 Locate the power supply on the computer and the wires that connect to it there should be a 4 pin female con
18. ging The special design incorporates a convenient accessible sliding tray for a benchtop transilluminator Its many dynamic features make this the darkroom suitable for most every imaging application WWW UVP COM 9 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 MINI DARKROOM gt Camera UJ Mounting bolts and washers Camera mount Zoom lens m Rubber light tight seal F Darkroom door G Transilluminator LN Trad mdi NOTE THE TRANSILLUMINATOR POWER CORD PLUGS INTO THE DARKROOM THIS ENABLES THE DARKROOM DOOR CONTROL THE POWER SWITCH OF THE TRANSILLUMINATOR OPEN OFF CLOSED ON WWW UVP COM 10 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 UV WHITE DARKROOM A Camera B Mounting bolts and washers C Interchangeable Camera Mount D Zoom lens E Optional Mounting Positions and Plugs F Darkroom Door G Transilluminator NOTE THE TRANSILLUMINATOR POWER CORD PLUGS INTO THE DARKROOM THIS ENABLES THE DARKROOM DOOR TO CONTROL THE POWER SWITCH OF THE TRANSILLUMINATOR OPEN OFF CLOSED ON WWW UVP COM 11 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 EPICHEMI II DARKROOM A Mounting knobs and washers Camera Camera mount Zoom lens Rubber light tight seal White Light Power Switch
19. liver Stain SYPRO Red SYPRO Orange NO INTEGRATION NECESSARY 1 2 3 O gt 10 Make sure the Ethidium Bromide filter is not on the lens or selected on the darkroom Open up LabWorks Click on the Camera Icon Open up the Integration tab Click on the start Preview icon Place the UVP gel cutter on the transilluminator Zoom in all the way and focus Adjust the light shutter on the zoom lens Make sure Accumulate Integrate and Dynamic Integration are NOT checked Click the Capture button to capture the image Fluorescent Gels DNA RNA Gels Transmitted UV Light Ethidium Bromide SYBR Green SYBR Gold Fluorescein Rhodamine Texas Red WWW UVP COM 26 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 Usually requires integration to make stained bands appear To increase the brightness of the bands increase the integration time 1 2 3 O 0 N D 11 12 Make sure the appropriate filter for the right stain is on the lens or selected on the darkroom Open up LabWorks Click on the Camera Icon Open up the Integration tab Click on the Start Preview Icon Place the UVP Gel cutter on the transilluminator Zoom in all the way and Focus Adjust the light shutter on the zoom lens Check the Integration box and set the integration seconds to the desired exposure Make sure Accumulate and Dynamic Integration are not checked Click
20. nector on one end Plug in the 4 pin male connector from what you have just installed to the 4 pin female connector The computer should now supply power to the camera Then connect the 8 pin camera power cable and the internal Power Plug that was just installed 5 Once these connections are secure plug the other end into the Image Acquisition Board This 25 pin female connector on the computer is adjacent to where the monitor cord is plugged into WWW UVP COM 21 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022 B 8 bit Monochrome CCD Assembly and Installation instructions MOUNTING THE CAMERA 1 Unpack the camera and zoom lens from their protective boxes and remove the protective plugs 2 Screw the zoom lens into the end of the camera housing Make sure that the UV filter is on the end of the lens if doing Ethidium Bromide work Note When using the EpiChemi II darkroom the UV filter is not necessary on the lens 3 To attach the camera bracket to the top of the darkroom place the black rubber gasket over the four screw holes and align the camera mount Screw in the 4 provided screws to attach the camera mounting bracket and light sealing gasket to the top of the darkroom The slots for the mounting bolts should face the front and back of the darkroom e Light Sealing se WWW UVP COM 22 US Technical Support 1 800
21. sives or detergents Transilluminator gently wipe with a non abrasive cloth to clean You can use distilled or deionized water to rinse the surface Folddown platform wipe with a non abrasive cloth to clean You can use distilled or deionized water to rinse the surface WWNW UVP COM 28 US Technical Support 1 800 452 6788 UK Technical Support 44 0 1223 420022
22. t 1 800 452 6788 UK Technical Support 44 0 1223 420022 ASSEMBLING INSTRUCTIONS 1 2 Mount the column the baseboard using the screws washers and wing nuts see drawings A and Mount the two cranks on the hexagonal studs in such a way that the pin of the studs engages in the recess of the cranks see drawing ADJUSTMENT 1 2 3 Vertical adjustment is by means of crank A the sliding carrier is fixed in position with Setscrew B Horizontal adjustment of the camera bracket J is done by crank it is fixed in position with Setscrew D The recessed adjustment screws G are used to control smooth movement of the horizontal and vertical adjustment An Allen type wrench is required to turn screws MOUNTING THE CAMERA 1 Unpack the camera and fixed lens from their protective boxes and E remove the protective plugs 2 9 Screw the fixed lens onto the end of we the C mount of the camera Make sure that the UV filter is on the end a of the lens if doing Ethidium p Bromide work QUICK SNAP ON MOUNT 1 in picture C above Place the triangle onto the Adjustable Camera Arm J and tighten the bolt Detach the recessed square with the mounting screw by disengaging the locking lever Screw the camera onto the side that has one mounting hole Secure the connection well Do not worry about the spring loaded tab WWW UVP COM 8 US Te
Download Pdf Manuals
Related Search