SmartLog V5™ Turnstile Installation, Operation and Maintenance
Contents
1. fit Wiring Inspect all wires and contacts for exposure to any metal parts that may lead to a short EXTERIOR CARE 1 Stainless Steel Stainless steel surfaces include the turnstile arms and lid and depending on the finish ordered the cabinet Stainless steel surfaces may be cleaned using any commercially available polish or cleaner If a heavier scratch or mark is apparent a metal blend and finish pad 3M or equivalent may be used A quality automotive wax may be used to buff the cabinet after cleaning Aluminum Head The conical shaped aluminum head can be cleaned using a soft damp cloth Powdercoat Finishes Powdercoat finishes should be cleaned using a soft damp cloth Any deep scratches or chips in this type of finish should be touched up to prevent a rust spot from forming If left untreated rust will spread Touch up paint is available from Alvarado ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 20 TROUBLESHOOTING EDC ITEMS TO CHECK FIRST e Always check for and remove any debris in or around the solenoid plunger do not however lubricate the solenoid plunger It is designed to operate dry e Always check the wiring of the turnstile for any loose or bad connections Be sure to use the wiring diagram that corresponds to the turnstile model installed e REMI2. 1 opivevery dr EA uad mil Med Ta XN th ac CLG CNO CON CAT Con IE LUNG K KEY OVER AIDE KEY REMOTE UNLOCK cw REMOTE UNLOCK W ACTIVATION ACCESS E t TH Saito ACTIVATION ACTIVATION T mah 5 CCW cw hj BOLENOID COW ACTIVATION TEST SWITCH TIMED DELAY RESET TIMER Positions T3 and T4 Switch Setting 5 seconds 10 seconds I SX Clockwise Fail Safe Counter Clockwise Fail Safe Clockwise Fail Lock Counter Clockwise Fail Lock Timer see chart E IK T Timer see chart Timer see chart MR E Timer see chart 15 seconds Feedback Pulse 100ms W 2 89 Feedback Pulse 300ms 20 seconds Default Setting J53 LED Option MIB B option a S Std Optics 83 1st Sensor Optics Not Used A ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 10 ATC Controller Terminal Descriptions Activation Test Button i did O ws rorocy oRvY x a f J19 Roy ZMIMIL AIA I cm LALI G I LE m AAA Bp thie TI O e ACE GND BEI OSs GNN POS siga A ACC GND REJ CLS GND OPN CNT Solenoid VDC wire connection Left Hand Counter Clockwise Direction Solenoid VDC wire connection Left Hand Counter Clockwise Direction
3. Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 7 d d m m s A m ed wa m _ P d w m nl m ra mnm rni aa ELECTRICAL AND ACTIVATION WIRING INSTRUCTIONS TOOLS REQUIRED Wire Stripper PARTS REQUIRED Wire Nuts INSTRUCTIONS NOTE USE ONLY SKILLED ELECTRICIANS TO CONNECT POWER 1 2 Make sure that primary power to the unit is off Locate the wiring diagram for the turnstile model being installed The model number is listed on the manufacturer s serial number plate mounted near the head on the cabinet fascia e g EDC 4X R EDC AX R FS Unlock and open lid Connect 110 VAC to the transformer power switch box Connect the access control system activation leads to the board Review all electrical wiring and contacts for exposure to any metal parts that may lead to a short Manually rotate the turnstile and inspect the optical sensors for proper alignment and free rotation of the sensor feedback disk Turn ON the primary power to the unit For both fail lock and fail safe units the turnstile should be locked in the controlled direction s when power is applied Turn the primary power OFF again If the unit is fail lock confirm that the turnstile remains locked upon loss of power If the unit is fail safe confirm that the turnstile u
4. IT TECHNICAL BULLETIN TB 6582 SmartLog V5 Turnstile Installation Operation and Maintenance Figure 1 EMIT 50770 SmartLog V5 Turnstile Description Use the EMIT SmartLog V5 Turnstile to enforce ESD access control to your facility The EMIT 50770 Turnstile is constructed of high quality stainless steel and includes a SmartLog V5 with mounting fixture The turnstile will activate when a user passes their required ESD test Use the turnstile s integrated timer to set its unlock time to 5 10 15 or 20 seconds By touching the solid state switch once the SmartLog V5 tests the resistance path limits of the worn wrist strap and both worn ESD footwear independently in less than 2 seconds It may also test a worn ESD garment if it is used as part of personnel grounding path Test results are electronically stored in the SmartLog V5 and easily downloaded to a PC for logging records and evaluation This product can be used as one of the tools to fulfill the ANSI ESD 520 20 section 7 3 Compliance Verification Plan See TB 6578 for more information on the patented EMIT SmartLog V5 US Patents 6 078 875 and 6 809 522 VA s r M jp AAN Made in the United States of America ESD Association Information Compliance verification should be performed prior to each use daily shift change etc The accumulation of insulative materials may increase the foot grounder system resis
5. ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 26 EDC EXPLODED PARTS DETAIL continued ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 27 EDC EXPLODED PARTS DETAIL continued tma EDGSHOECOMPRESSONKT 1 50047280 EDGARMASSYDECELERATONKIT 1 ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 28 EDC EXPLODED VIEW PARTS LISTING ITEM KIT PARTNUMBER DESCRIPTION aTY QTY PER KIT 1 50 04 7130 EDC BASIC MECH FRAMEKIT 1 EDCBASICMECH FRMASSY 1 L 194648LOCKNUT ZNC 4 x JVA CRESENT RETAINING RING 2 pot 8 CRESCENT RETAINING RING 10 EDC BASIC MECH FRMASSY _ 4 2 50 EDC LK EDC EDCX SLT LOCKARM KIT 1 L EDOLOCK ARM KO LEFT HAND 1 pot EDOLOCK ARMKORGHTHAND 1 pot 3 8CRESCENTRETAININGRING_ 4 P88 X 1 ROLL PIN BLACK OXIDE 2 3 50 10 1070 SOLENOID 12VDC KIT 1 Solenoid 12V DC 2 Screw 8 32 X 3 8 SHCS BLK OXIDE 8 I 200 Washer 8 Internal Tooth Zine 8 4 50 EDC S1 EDCXSPRINGKIT______ 1 1 jEXSPRNGCOMPRESSON
6. 50 11 9060 EDC HYDRAULIC CLOSUREKIT 1 EDC SPRING COMPRESSION ARM T pot 1 EDCHYDRAUICCLOSUREUNT 1 EDCCLOSUREUNITSPACER_____ 1 po 4 20 5 8 SHCS BLKOXIDE 2 po 1 4 20X 3 4 BHSCS BLKOXIDE 4 __ 420 HEXNUT ZINC 4 gato 1 4 SPLIT LOCKWASHER ZINC 60 ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 29 LUBRICATION GUIDE 3LIHM MOV 19 A8 GALVOIGNI SVIYV TIV 31VI9149N1 suuds uo pup D8ID 2DJUOO 1 10404 9 xis gt A PO sais 27912 IU HH aa SV3 1V AWOS OL JANO SNOISN3 LX3 SHOLVOl ddV SVJIY4V ASAHL 31V9149N 1 OL SINYV ATILSNANL ALVLOY ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com Page 30 EDC EDCX PUD1535R4 0
7. Right Hand Clockwise Direction Providing a continuous dry contact at this terminal places the turnstile in an unlocked OPEN mode This mode overrides the access control system operation If a green entry light is installed Location J10 it will be illuminated green continuously Note this connection is shown using a key switch in the schematic Outputs a dry contact upon rotation of the turnstile This feature can be used to output a count signal to an external system such as Alvarado s GateWatch or to provide feedback to the access control system that a turnstile rotation has taken place Entry confirmation signal upon turnstile rotation Right Hand Clockwise Direction Entry confirmation signal upon Common dry contact connection for CNT count turnstile rotation Right signal output See J3 CNT description Hand Clockwise Direction Allows user to test turnstile Depressing button simulates input to Location ACC Entry Accept If turnstile solenoid fires after depressing button AND relocks after a single rotation of the turnstile arm OR upon time out the turnstile is functioning correctly in the Right Hand Clockwise Direction activation Right Hand Clockwise Direction ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 13 Connections mU J19 i 12 Mi y TT
8. 909 664 9980 Chino CA for a Return Material Authorization RMA and proper shipping instructions and address EMIT will quote repair charges necessary to bring your unit up to factory standards Warranty Exclusions THE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU OF ALL OTHER PRODUCT WARRANTIES EXPRESSED AND IMPLIED INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH ARE SPECIFICALLY DISCLAIMED The express warranty will not apply to defects or damage due to accidents neglect misuse alterations operator error or failure to properly maintain clean or repair products Limit of Liability In no event will EMIT or any seller be responsible or liable for any injury loss or damage direct or consequential arising out of the use of or the inability to use the product Before using users shall determine the suitability of the product for their intended use and users assume all risk and liability whatsoever in connection therewith TURNSTILE Limited Warranty EMIT expressly warrants that for a period of one 1 year from the date of purchase EMIT SmartLog V5 Turnstiles will be free of defects in material parts and workmanship labor Within the warranty period a credit for purchase of replacement EMIT turnstiles or at EMIT s option the turnstile will be repaired or replaced free of charge If product credit is issued the amount will be calculated by multiplying the unused portion of the expected five year life time
9. TUE C Wu Y UN I re e O gt RU Fu Of N CO 5 N J 1 hdi 25 a Cc e ANAL ledges we n 5 E AE NI mr eit c 1111118 1414 K 7 v Jp2 nm ala SI J YOU Y OK 33 Cou con ann iG 2 Wd POWER INPUT LU Connections 3 9 EVN SSS 5 J ed Doia DD a II e te l Ae 4 o s 204 BP 52 ov Ue Ow 4 Qd ds de c c9 VENE TET EL LL T3 B oroso ACC CLS GNO CNT 0 5 Y A 2 2 gt e Si oi B gt CH CNT CAL CNT RESET Location J2 CCW CNT Output of contact closure upon turnstile rotation Left hand Counter Clockwise Direction J4 Power Connection for low voltage Input power Single throw relay output for connection to Alvarado battery powered digital counter The ATC will accept 10 VAC or 13 5 VDC power If primary power is not run to the turnstile low voltage power is connected here and the green ground wire must be grounded to the chassis J5 Optical Connection for sensors The ATC uses input from the sensors to provide sensors rotation control functionality J8 CW CNT Outp
10. adjusted or disabled in the field Adjustments can be made for each electrically controlled direction ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 4 A OVERVIEW OF INSTALLATION SLAB REQUIREMENTS SLAB REQUIREMENTS MINIMUM THICKNESS 4 LEVEL SOLID CONCRETE DO NOT INSTALL ON ASPHALT OVERVIEW OF INSTALLATION STEPS TOOLS REQUIRED Determine turnstile locations taking into account power and activation wiring Heavy Duty Drill or Roto Hammer B Anchor turnstile 1 Concrete Drill Bit C Connect Power Ratchet with 15 16 D Connect Activation Wiring Socket Torque Wrench 1 8 Allen Wrench PARTS REQUIRED Hammer SUPPLIED BY ALVARADO Shop Vac 2 each All Thread Rods Tape Measure gt hC Chalk sC sz Ips s Shim Material 2 each Anchors Safety Glasses TURNSTILE LOCATION AND BARRIER SPACING Verify layout location Note the turnstile arm should be approximately 2 from the next unit or outside barrier Barrier or adjoining Turnstile Turnstile Establish Clearance NNNNNNN ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 5 INSTALLATION INSTALLING THE TURNSTILE Open the turnstile lid Place the turnstile in the desired location Remove the
11. ARM 1 EDOSPRING BACK PAWL EDOSPRING SOLENOID FAILSAFE 2 x 1DGSPRNGRETURNSOLENIDFS 2 pot EDCSPRINGLOCKARM________ RE SPRING RETURNHYD OSURE LL U L PED LINK SOLENOID FAILLOCK oo rn RS o O JEDCRATCHETS MAINSHAFTASSY 414 x EDC WHEEL OPTICALENCODER 1 ooo oc o EDCFLATBEARANGG ______ 2 po 11 420 X 1 1 4 PHPMS ZINC E po 13 6806 X 1 1 2 HHCS GRD5 ZINC 3 SPLITLOCKWASHER ZINC o 8 8 SPLITLOCKWASHER ZINC_ 3 S116 X2 ROLL AH 1 Dx 0 032 SHM BRASS Tra SEO AST pot EDCOPTICALSENSORASSY Oo HA 20HEXNU ZNC 0 2 pot HAFLATWASHERZNC J 2 O Pe SPLITLOCKWASHER ZINC 2 ___ 7 50 10 7821 ATCDRIVERBOARDKT 1 o MSTX EDCX ATC DriverBoard 1 At Standoff 1 6 32 Male Female I 4 8 50 04 7241 X EDC SHOECOMPRESSIONKT 1 EDGARMCOMPRESSIONZNCPLATE 1 1IEDGSHOECOMPRESSIONREAMD 1 EDOSPRING COMPRESSIONARM 1 pot 8 5 800 1 16 2 3 8 CRESCENT RETAINING RING 4 9 50 04 7280 EDC ARM ASSY DECELERATIONKT 1 tEDGARMASSY DECR ERATION 1 pot EDCISPRINGRETURN HYD CLOSURE 1 HE x 832X1THSMSZNO i o j f 1 amp 32HEXNU ZNC j 1 x 8 INTERNL TOOTHLCKWSHER ZINC 1 FAB RETAININGRING 2 P IA 10
12. CX PUD1535R4 0 Page 14 Connection for EL function OPTIONAL light board Support for 5 and 12 VDC LED lights Use jumper JP1 to set voltage If red green end light boards are used the green light signifies that the turnstile is ready to accept an activation for the direction shown When the CLS and GND connection is closed the red light will be illuminated and signifies that the turnstile will not accept an activation Refer to description for CLS on J3 and J7 Switches we a f o J i sd di A A Ic rh rhe NE AMAIA AA W ANE FoNTLTTILIUIPa eS Q esa 2 3 1 Y N zu ate T m x i x id DOE f CO er se 7127 x iui vas etl HW o AA XXIII U 1 5 1 5 1J151 TESES Om m w w du ja NM 9 9 E E US RI NEN CET d E I lt 2 agg pa wow L ib TM 3 io 1 a sde 1 7 0 1 k Py Om 110 79 e Wit 439525 39 9954 oro aoe 0 CNT GND OPN CNT COM 4 A con LES S 3 CLS GNO OPN ACC GNO REJ CLS Eu Dee eem a Location SW3 Reset Local Battery If blue counter wires are attached to the board depressing counters Counter Reset this button will reset the counters If two counters are Switch installed and wired both counters will be reset SW6 Allows user to test Depressing button simu
13. Connections to the SmartLog V5 right view Set the power switch located on the power box to the cover off ON position 6 Align the slots on the back of the SmartLog V5 with the hooks on the turnstile bracket 3 Install the mounting bracket onto the turnstile s cover using the three 10 32 screws washers and nuts From top to bottom the installation order is screw washer mounting bracket turnstile cover nut 4 Route the SmartLog s foot plate cable power adapter ground cord relay wires and Ethernet cable through the turnstile and bracket Figure 4 Locating the mounting hooks on the bracket Figure 2 Routing the cords and cables through the turnstile s cover and bracket 5 Follow Figure 3 and connect all of the cables to the SmartLog V5 EMIT 3651 Walnut Avenue Chino CA 91710 909 664 9980 Fax 909 627 7449 Website DescoEMIT com TB 6582 Page 2 of 5 O 2012 DESCO INDUSTRIES INC Employee Owned 7 Slide the SmartLog V5 into the bracket from top to bottom Secure the SmartLog V5 to the bracket by fastening the included 4 40 screw on the left side of the tester Operation NOTE The SmartLog V5 must first be programmed with the user ID table using the TEAM5 Software before being deployed for employee use or the default test slide down securing it into place with the 4 40 screw 8 Locate the foot plate cable at the base of the turnstile and connect it to the Dual Independ
14. NDER NOTE You can always test the functionality of the turnstile by pressing the Entry Activation Test Button s on the controller board Symptom Possible Cause Solution Turnstile The turnstile is not powered Confirm that the ON OFF switch is in the ON does Fail lock units only position not unlock Confirm that the fuse is still good If necessary replace the fuse Confirm that the LED on the controller board is on and not flickering If the LED on the controller board is not lit verify that proper voltage 110 120VAC is being provided to the Outlet Box inside the turnstile Do this by plugging in any device such as a light drill radio etc the proper voltage 110 120VAC is being provided to the outlet box verify that the controller board is receiving approximately 10 VAC from the transformer The turnstile is not receiving Ensure that the access control system is an activation signal from the properly connected to the Entry Accept Access Control System terminal s on the controller board Confirm that the access control system is providing a proper activation signal A lock arm spring is missing Replace the springs broken or worn out NOTE The springs installed in the EDC turnstile are specifically designed for use in this application Use only springs purchased from Alvarado Manufacturing Turnstile springs are not interchangeable and should only be used in their designated locations The lock arm is sticking
15. NT and COM feedback to 300ms Sets operation for when a JS3 yellow uM oets operation for when a JS2 red green red light board is used The green light board is used The red yellow light is lit when the turnstile is light will be lit when the turnstile is powered and ready for card powered and ready for card presentation When a contact is presentation When a contact is provided to Entry Accept Location provided to Entry Accept Location ACC the green light illuminates The ACC the green light illuminates green light stays on for a user The green light stays on for 20 definable time or until the turnstile is seconds or until the turnstile is rotated See the explanation rotated Requires light board provided for Switch SW4 Whena connection to J9 and or J10 contact is provided to Entry Reject Default Location REJ a Red light illuminates The red light illuminates for 3 seconds Requires light board connection to J9 and or J10 Sets operation to standard optical Sets operation to custom optical sensor configuration for passage sensor configuration for passage feedback after second sensor feedback on first sensor detection detection Default Not used Default TIMED DELAY RESET TIMER Positions T3 Switch Setting and T4 5 seconds 10 seconds 15 seconds 20 seconds Default Setting ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email
16. PENDENT FOOT PLATE Dimensions 14 0 x 16 0 x 0 9 See TB 6581 for more information 35 6cm x 40 1cm x 2 3cm Weight 7 5 lbs 3 4 kg 45 1 39 5 114 6cm 100 3cm 9 5 24 1cm 23 9 60 7cm Figure 7 Dimensions of the EMIT 50770 SmartLog V5 Turnstile EMIT 3651 Walnut Avenue Chino CA 91710 909 664 9980 Fax 909 627 7449 Website DescoEMIT com TB 6582 Page 4 of 5 O 2012 DESCO INDUSTRIES INC Employee Owned Limited Warranty SMARTLOG V5 TESTER Limited Warranty EMIT expressly warrants that for a period of five 5 years from the date of purchase EMIT SmartLog V5 s will be free of defects in material parts and workmanship labor Within the warranty period a credit for purchase of replacement EMIT products or at EMIT s option the product will be repaired or replaced free of charge If product credit is issued the amount will be calculated by multiplying the unused portion of the expected five year life times the original unit purchase price Call our Customer Service Department at 909 664 9980 Chino CA for a Return Material Authorization RMA and proper shipping instructions and address Please include a copy of your original packing slip invoice or other proof of date of purchase Any unit under warranty should be shipped prepaid to the EMIT factory Warranty replacements will take approximately two weeks If your unit is out of warranty call our Customer Service Department at
17. Solenoid VDC wire connection Right Hand Clockwise Direction Solenoid VDC wire connection Right Hand Clockwise Direction Allows user to test turnsti activation Left Hand Co Clockwise Direction gt CNT COM J12 S di die k ed Jo Kei a J3 1 ad x E lt m m lt le NSORS TEA Ex a TISTISTIC a i lo 5 7 am eS Ss ATLETI TOES ecen a d A 6 9 RELI 29 k K h a gt e 7 22222 GND OPN CNT C 8 GND REJ CLS K JP2 Lk 5 Jot FEET TEET CRET TEES i COM le unter ALVARADO X3 030522728 X R G Y 0 gt ACC GND REJ CLS GND OPN CNT COM Connection for Counter Clockwise Solenoid Universal polarity Connection for Counter Clockwise Solenoid Universal polarity Connection for Clockwise Solenoid Universal polarity Connection for Clockwise Solenoid Universal polarity Depressing button simulates input to Location ACC Entry Accept If turnstile solenoid fires after depressing button AND relocks after a single rotation of the turnstile arm OR upon time out the turnstile is functioning correctly in the Left Hand Counter Clockwise Direction 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 EDC EDCX PUD1535R4 0 Fax 1 909 628 1403 Email information alvaradomfg com Page 11 Board M GND Ground CLS Clo
18. TE By default the turnstile will remain unlocked until either the operator passes through or 20 seconds expire See page 17 in the attached Alvarado EDC Installation and Maintenance Manual for instructions on modifying the turnstile s Timed Delay Reset Timer EMIT 3651 Walnut Avenue Chino CA 91710 909 664 9980 Fax 909 627 7449 Website DescoEMIT com TB 6582 Page 3 of 5 2012 DESCO INDUSTRIES INC Employee Owned Calibration Specifications Frequency of SMARTLOG V5 TURNSTILE recalibration should Operating Voltage 110 VAC 60 Hz be based on th b Operating Temperature 32 F 104 F 0 40 C those ESD sensitive Dimensions Crated 42 x 40 x 49 items handled and x 107cm x 102cm x 124cm the risk of failure for the ESD protective Dimensions Uncrated See Figure 7 equipment and materials In general Weight Crated 385 Ibs 175 kg EMIT recommends Weight Uncrated 285 Ibs 129 kg that calibration be performed annually SMARTLOG V5 TESTER Use the EMIT 50424 Operating Voltage 100 240 VAC 50 60 Hz Limit Comparator Operating Temperature 32 F 104 F 0 40 C to perform periodic testing once every Dimensions 8 3 x 5 8 x 1 9 6 12 months of the SmartLog V5 The Limit Comparator 21 1cm x 14 7cm x 4 8cm can be used on the shop floor within a few minutes virtually eliminating downtime verifying that the tester is operating DUAL INDE
19. control for the Counter Clockwise direction in fail lock configuration Power is applied to solenoid upon activation signal to release lock arm for rotation Adjustment control of the maximum throughput time allowed for an individual to completely travel through the turnstile before the turnstile automatically relocks Used with switch position T4 Always test operation after adjusting to ensure that the set time allowed is compatible with the functionality required for the turnstile Refer to the Entry Time Adjusting Control Switch settings table below Default Adjustment control of the maximum throughput time allowed for an individual to completely travel through the turnstile before the turnstile automatically relocks Used with switch position T3 Always test operation after adjusting to ensure that the set time allowed is compatible with the functionality required for the turnstile Refer to the Entry Time Adjusting Control Switch Settings table below Default i a B a Sets solenoid control for the Clockwise direction in fail safe configuration Power is applied to solenoid for locked condition and removed upon activation signal to release lock arm for rotation Sets solenoid control for the Counter Clockwise direction in fail safe configuration Power is applied to solenoid for locked condition and removed upon activation signal to release lock arm for rotation Adjustment control of the maximum throughp
20. controlled in both directions OTHER CONFIGURATIONS DESCRIBED IN DRAWINGS Fail Lock Turnstile locks when power is removed or lost Turnstile will unlock only when both power and an activation contact are supplied This is how the turnstile leaves the factory unless specified otherwise Fail Safe Turnstile unlocks in the event of power loss Turnstile will relock when power is supplied Activation Alvarado s turnstile requires a momentary dry contact of 25 ms or greater The turnstile will not buffer activations Once activated the turnstile will not accept another activation until either the turnstile arm has been rotated or the time limit set has expired if the adjustable timed delay automatic relock feature is enabled Lock Unlock Override This option overrides the access control system allowing one or both directions of passage to be locked or unlocked with a key Locks may be located remotely or locally Local locks are generally located near the arms on the cabinet fascia When both directions have key overrides the locks are keyed alike Adjustable Timed Delay An activation signal unlocks the turnstile for one entry Once the turnstile is unlocked the user is allowed a set amount of time to pass through the turnstile If the turnstile arm is not rotated within the time frame allowed the turnstile will automatically relock The duration of time allowed before the unit automatically relocks can be
21. d with the plunger in the release position sticking ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 23 EDC PLAN amp ELEVATION VIEW DRAWINGS 40 5 34 125 DIMENSIONS Model A B C EDC 27 0 15 5 25 0 EDC Extended 34 0 20 5 30 0 EDC Bullnose 36 5 15 5 25 0 EDC Ext Bullnose 43 5 205 300 STANDARD EXTENDED EDC BULLNOSE EXTENDED BULLNOSE CABINET TOP VIEW EDC CABINET TOP VIEW lt B 4 B gt cCc 4 C gt ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 24 EDC EXPLODED PARTS DETAIL aa The turnstile model shown is an EDC 6X Fail Lock unit with Key Overrides for both directions TL HL SE OE D ue EDC SUB ASSEMBLIES EDC Frame Plate Sub Assembly EDC Head and Arms Sub Assembly EDC Hydraulic Closure Sub Assembly EDC Ratchet Sub Assembly EDC Opto Interrupter Mounting Plate Sub Assembly EDC Compression Shoe Sub Assembly ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 25 EDC EXPLODED PARTS DETAIL continued
22. elock if an entrance does not occur The turnstile automatically relocks before the user can pass through the turnstile The turnstile head does not turn smoothly The solenoid plunger is The duration of the timed delay automatic relock feature is too long The duration of the timed delay automatic relock feature is too short Increase the time duration with the dip switch settings as described on Page 17 before the unit times out The dip switch settings that control the timed delay The dip switch settings that control the timed delay are on terminals T3 and T4 on SWA4 see page 17 Clean and lubricate the pivot points as described in the Maintenance section of this document f necessary adjust the hydraulic dampening unit as described in item 5 of the Maintenance section on Page 19 The turnstile is not properly lubricated The solenoid is obstructed by Remove any dirt or debris that may be foreign matter or debris obstructing the solenoid or the plunger The solenoid bracket is out of Adjust the solenoid plunger limiting Bracket alignment NOTES 1 The EDCX turnstile is designed to receive a momentary dry contact closure The duration of the contact must be 25 ms or greater 2 Maintain a spacing of 1 75 from the face of the solenoid to the face of the bracket Bend the bracket back towards or away from the solenoid to adjust Check the 1 75 measurement with both the plunger pulled in an
23. ent Foot Plate Place the foot plate at the base of the turnstile so operators can place their feet on it while performing tests at the turnstile s entrance Figure 6 Installing the Dual Independent Foot Plate 9 Complete the installation by establishing communication to the SmartLog V5 via the Ethernet cable See the Ethernet Setup procedure in TB 6578 for more information Figure 5 Sliding the SmartLog V5 into the bracket and settings will be applied See the TEAM5 User Manual for more information 1 Initiate the test procedure by identifying yourself to the SmartLog This may be done using the keypad barcode badge scanner or proximity badge reader if supplied Follow the prompt on the SmartLog s display 3 When performing a footwear test be sure to place both feet on the dual foot plate one foot per plate When performing a wrist strap test be sure to completely plug in the wrist cord into the tester s jack Press and hold the metal touch plate on the tester to perform the test Hold your finger on the touch plate until the results of the test are displayed If performing a wrist strap test and the wrist strap status LEDs do not illuminate verify that the wrist cord is correctly inserted into the tester The relay terminal will activate and unlock the turnstile if the defined tests are passed Pass through the turnstile The turnstile Will re lock after one rotation NO
24. er Pan Head Screw 4 40 thread Pan Head Screws 10 32 thread Nuts 10 32 thread Washers Wall Mounting Anchors Wall Mounting Screws 10 x 1 1 2 Turnstile Keys Zip Ties with Adhesive Pads Certificate of Calibration CORD WWW a EMIT 3651 Walnut Avenue Chino CA 91710 909 664 9980 Fax 909 627 7449 Website DescoEMIT com TB 6582 Page 1 of 5 November 2012 O 2012 DESCO INDUSTRIES INC Employee Owned Installation Installing the Turnstile A 110VAC power line and Ethernet line are needed at the installation location of every SmartLog V5 Turnstile Be sure to route these lines to the installation site prior to anchoring your turnstile See the attached Alvarado EDC Installation and Maintenance Manual for instructions on anchoring and wiring the turnstile Do not mount the SmartLog V5 and its mounting bracket to the turnstile until it is properly anchored and wired Ground Relay Power Installing the SmartLog V5 to the xw Foot Plate Turnstile See TB 6578 to learn more about the features and components of the SmartLog V5 M EMIT recommends making any adjustments to its clock or test configurations prior to installing it to the turnstile 1 Disconnect the SmartLog V5 tester from the mounting bracket by removing the 4 40 pan head screw located on the left hand side of the tester 2 Open the turnstile s cover using the included keys Figure 3
25. functioning correctly the unit will time out and automatically relock after 20 seconds The controller board provides four different time out timer settings The available timer settings are 5 10 15 or 20 seconds The timer settings are set using terminals T3 and T4 of SW4 on the controller board NOTE Always test the turnstile after making adjustments to the timed delay feature If the adjusted time duration is too short the unit will relock too quickly and users will not be able to enter through the turnstile 16 For bi directionally controlled turnstiles Model EDC 6X units ONLY repeat steps 12 through 15 for the exit direction and confirm correct functionality 17 Close the turnstile lid and lock ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 9 Primary Power Wire Connection for 110 and 220 Options 10 7821 ATC Rev F 12V Wiring Schematic 220 VAC OPTIONAL COUNTER COUNTER Cw cow OPTICAL SENSORS E a Eke N HOVAC II eb amp 4 Bm seme 1020 5020 SS e riw 3 ad iti de 112 Position board l ocv ANS Sino os J Am i E BNMONILILILIUTIE yir ril Sis so that input ms w n T 3 terminal is r ALLLLLLIL adjacent to power supply see LE RE S du i Shas w E IET i 3 7
26. information alvaradomfg com EDC EDCX PUD1535R4 0 Page 17 Fail Safe Configuration e The dipswitches on the ATC controller board are turned to Fail Safe e The solenoid springs are configured per the above figure e Each solenoid is wired to its corresponding input on the ATC board 028 10 vm ISE USOS L OURIDE ann CCH CH Jv e ACC GND REJ CLS GND OPN CNT COM T ba suma ACC GND REJ CLS GND OPN CNT COM 1 e The dipswitches the ATC controller board are turned to Fail Lock e The solenoid springs are configured per the above figure e Each solenoid is wired to its corresponding input on the ATC board J 2 JP2 KJ E os eee TEET E t dd S C CRC EE EEN ey vie eer KORG dila gt ACC GND REJ CLS GND OPN CNT COM de OURIDE fccul Toy p ACC GND REJ CLS GND OPN CNT Reference Alvarado Field Service Document 3293 for converting from Fail Safe to Fail Lock ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 18 MAINTENANCE Inspect the installed turnstiles approximately 60 days after the initial installation Thereafter the frequency of maintenance will depend on usage and the environment We suggest inspecting and lubricating the turnstile interior approximately twice a year Interior maintenance should be performed more freq
27. lates input to Location ACC Entry turnstile activation Accept If turnstile solenoid fires after depressing button Activation Right AND relocks after a single rotation of the turnstile arm OR Test Hand Clockwise upon time out the turnstile is functioning correctly in the Button Direction Right Hand Clockwise Direction LH CCW Allows user to test Depressing button simulates input to Location ACC Entry Entry turnstile activation Accept If turnstile solenoid fires after depressing button Activation Left Hand Counter AND relocks after a single rotation of the turnstile arm OR Test Clockwise Direction upon time out the turnstile is functioning correctly in the Left Button Hand Counter Clockwise Direction D U ub J 1 CO 17 J1 13 JP2 510 MAS STE os ecocs Em ee eer OURIDET TARM s lr Ego rede ACC GND REJ CLS GND OPN CNT COM s FTE J9 fcc cw Sf e Acc GND REJ CLS GND OPN CNT ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 15 SW4 Switch Settings Explanation of switch positioned Switch Switch Explanation of switch positioned to left or OFF side Position Position to right or ON side Sets solenoid control for the Clockwise direction in fail lock configuration Power is applied to solenoid upon activation signal to release lock arm for rotation Sets solenoid
28. nd wire connection position for Entry Activation and Card Reject contact signal J7 REJ Unauthorized input This connection is used to tell the turnstile to ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 12 Board Em Location Description _ Entry Reject CLS Close Passage GND Ground CNT Passage Count COM Passage Count J OPN Open Passage T T T T T SW6 RH CW Entry Activation Test Button Explanation connection from the access control system Right Hand Clockwise Direction remain locked The access control system has determined that the card presented is unauthorized for entry Connection for placing turnstile in always locked CLOSED configuration Right Hand Clockwise Direction Providing a continuous dry contact at this terminal places the turnstile in a locked CLOSED mode This mode overrides the access control system operation If a red entry light is installed Location J10 it also will be illuminated continuously Note this connection is shown using a key switch in the schematic Ground wire connection for OPEN CLOSE passage control Ground wire connection for OPEN CLOSE Lane control Right Hand Clockwise Direction Connection for placing turnstile in always unlocked OPEN configuration
29. nlocks upon loss of power 10 Turn the primary power ON again ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 8 WIRING INSTRUCTIONS continued 11 Locate the Entry Activation Test Button s on the controller board inside the turnstile cabinet For help locating the test buttons please refer to the appropriate wiring diagram provided with this manual The test buttons are labeled SW6 and SW 7 on the wiring diagrams he SW6 Entry Activation Test Button is used to test the Clockwise CW controlled direction This is also known as the Right Hand RH direction The SW7 Entry Activation Test Button is used to test the Counter Clockwise CCW controlled direction This is also known as the Left Hand LH direction NOTE CCW and CW rotation is determined by viewing the rotation of the turnstile cam from above while the turnstile lid is open 12 Push the appropriate Entry Activation Test Button If the turnstile is functioning correctly the solenoid will fire and the turnstile will unlock 13 Rotate the turnstile arm in the appropriate direction If the turnstile is functioning correctly the turnstile will automatically relock 14 Push the Entry Activation Test Button again Observe that the turnstile unlocks but DO NOT rotate the turnstile arm 15 Wait for approximately 20 seconds If the turnstile is
30. or Clean and lubricate the lock arms binding in the locked position f necessary adjust the hydraulic dampening unit as described in item 5 of the Maintenance section on Page 19 The solenoid is defective Test and replace the solenoid as necessary The solenoid is de energizing Adjust the solenoid plunger limiting Bracket but the plunger is not firing See Note 2 on page 23 ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 21 TROUBLESHOOTING EDC continued Symptom Possible Cause Solution Turnstile does not relock The turnstile is not powered Confirm that the ON OFF switch is in the ON Fail safe units only position Confirm that the fuse is still good If necessary replace the fuse Confirm that the LED on the controller board is on and or flickering If the LED on the controller board is not lit verify that proper voltage 110 120VAC is being provided to the Outlet Box inside the turnstile Do this by plugging in any device such as a light drill radio etc the proper voltage 110 120VAC is being provided to the outlet box verify that the controller board is receiving approximately 10 VAC from the transformer The optical sensors are Remove any dirt or debris that may be obstructed or misaligned obstructing the optical sensors If necessary tighten the optical senso
31. r mounting screws so that the turnstile rotation tabs on the optical feedback disk pass through the sensors clearly The optical feedback disk is Repair or replace the feedback disk damaged or broken A lock arm spring is missing s Replace the springs broken or worn out NOTE The springs installed in the EDC turnstile are specifically designed for use in this application Use only springs purchased from Alvarado Manufacturing Turnstile springs are not interchangeable and should only be used in their designated locations The lock arm is sticking or Clean and lubricate the lock arms binding in the unlocked f necessary adjust the hydraulic dampening position unit as described in item 5 of the Maintenance section on Page 19 The solenoid is defective Test and replace the solenoid as necessary The solenoid is energizing but Adjust the solenoid plunger limiting Bracket the plunger is not firing See Note 2 on page 23 ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 22 TROUBLESHOOTING EDC continued Symptom Possible Cause Solution Decrease the time duration with the dip switch settings as described on Page 17 before the unit times out The dip switch settings that control the timed delay are on terminals T3 and T4 on SW4 see page 17 The turnstile does not automatically r
32. r Entry Activation and Card Reject contact signal This connection is used to tell the turnstile to remain locked The access control system has determined that the card presented is unauthorized for entry Providing a continuous dry contact at this terminal places the turnstile in a locked CLOSED mode This mode overrides the access control system operation If a red entry light is installed Location J10 it also will be illuminated continuously Note this connection is shown using a key switch in the schematic Ground wire connection for OPEN CLOSE passage control Providing a continuous dry contact at this terminal places the turnstile in an unlocked OPEN mode This mode overrides the access control system operation If a green entry light is installed Location J10 it will be illuminated green continuously Note this connection is shown using a key switch in the schematic Outputs a dry contact upon rotation of the turnstile This feature can be used to output a count signal to an external system such as Alvarado s GateWatch or to provide feedback to the access control system that a turnstile rotation has taken place Common dry contact connection for CNT count signal output See J3 CNT description This connection is used to tell the turnstile to unlock The ATC will accept a N O dry contact signal of 25ms or longer from the access control system and allows one turnstile rotation before relocking Grou
33. re are questions you may contact Alvarado at 909 591 8431 Monday through Friday 6 00 AM to 4 30 PM PST e Use only skilled individuals to install and service the turnstile e The turnstile is not a toy Do not allow children to play on or near the turnstile Do not allow horseplay near the turnstile e Follow a proper maintenance schedule using skilled individuals e Do not operate the turnstile if it has been damaged any manner Have the turnstile repaired or adjusted by a skilled service person before use e Do not modify or alter the turnstile e Do not operate the turnstile unless the hydraulic damping unit is operating and adjusted correctly For information on maintaining and adjusting the hydraulic damping unit please refer to item 5 of the Maintenance section on Page 19 e Do not use non Alvarado parts to repair the turnstile e For access control applications train all personnel that will be using the turnstile in the proper method of operation Ensure that as new users are properly trained as well SAVE THESE PRECAUTIONS ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 3 TURNSTILE CONFIGURATION DESCRIPTIONS Right Handed Turnstile Entry Left Handed Turnstile TURNSTILE CONFIGURATION EDC 4X Electrically controlled in one direction Locked in opposite direction EDC 6X Electrically
34. s the original unit purchase price Call our Customer Service Department at 909 664 9980 Chino CA for a Return Material Authorization RMA and proper shipping instructions and address Please include a copy of your original packing slip invoice or other proof of date of purchase Any unit under warranty should be shipped prepaid to the EMIT factory Warranty replacements will take approximately two weeks If your unit is out of warranty call our Customer Service Department at 909 664 9980 Chino CA for a Return Material Authorization RMA and proper shipping instructions and address EMIT will quote repair charges necessary to bring your unit up to factory standards Warranty Exclusions THE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU OF ALL OTHER PRODUCT WARRANTIES EXPRESSED AND IMPLIED INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH ARE SPECIFICALLY DISCLAIMED The express warranty will not apply to defects or damage due to accidents neglect misuse alterations operator error or failure to properly maintain clean or repair products Limit of Liability In no event will EMIT or any seller be responsible or liable for any injury loss or damage direct or consequential arising out of the use of or the inability to use the product Before using users shall determine the suitability of the product for their intended use and users assume all risk and liability whatsoever in connection therewith EMIT 3651 Walnu
35. se Passage GND Ground OPN Open Passage CNT Passage Count COM Passage Count GND Ground J3 J3 J3 J3 J3 J3 J3 J7 J7 Card Authorized input connection from the access control system Left Hand Counter Clockwise Direction Ground wire connection from the access control system for ACC REJ Left Hand Counter Clockwise Direction Card Unauthorized input connection from the access control system Left Hand Counter Clockwise Direction Connection for placing turnstile in always locked CLOSED configuration Left Hand Counter Clockwise Direction Ground wire connection for OPEN CLOSE Lane control Left Hand Counter Clockwise Direction Connection for placing turnstile in always unlocked OPEN configuration Left Hand Counter Clockwise Direction Entry confirmation signal upon turnstile rotation Left Hand Counter Clockwise Direction Entry confirmation signal upon turnstile rotation Left Hand Counter Clockwise Direction Card Authorized input connection from the access control system Right Hand Clockwise Direction Ground wire connection from the access control system for ACC REJ Left Hand Counter Clockwise Direction This connection is used to tell the turnstile to unlock The ATC will accept a N O dry contact signal of 25ms or longer from the access control system and allows one turnstile rotation before relocking Ground wire connection position fo
36. t Avenue Chino CA 91710 909 664 9980 Fax 909 627 7449 Website DescoEMIT com TB 6582 Page 5 of 5 O 2012 DESCO INDUSTRIES INC Employee Owned OALVARADO protecting assets and controlling the flow of people INSTALLATION AND MAINTENANCE MANUAL EDC EDCX WAIST HIGH SECURITY TURNSTILE This is the appropriate manual for EDC EDCX turnstiles manufactured on or after October 1 2010 Turnstile Serial Number ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 1 TABLE OF CONTENTS IMPORTANT SAFETY PRECAUTIONS PAGE 3 TURNSTILE CONFIGURATION DESCRIPTIONS PAGE 4 OVERVIEW OF INSTALLATION STEPS PAGE 5 CONCRETE SLAB REQUIREMENTS amp LAYOUT SPACING INSTALLATION PAGE 6 ELECTRICAL AND ACTIVATION WIRING INSTRUCTIONS PAGE 8 PRIMARY POWER CONNECTION 10 7821 ATC WIRING SCHEMATIC PAGE 10 FAIL SAFE FAIL LOCK CONFIGURATIONS PAGE 18 MAINTENANCE PAGE 19 TROUBLE SHOOTING PAGE 21 EDC PLAN amp ELEVATION VIEW DRAWINGS PAGE 24 EXPLODED PARTS DETAIL PAGE 25 NUMBERED PARTS LIST FOR EXPLODED PARTS DETAIL PAGE 29 LUBRICATION GUIDE PAGE 30 ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 2 IMPORTANT SAFETY PRECAUTIONS e Read this manual in its entirety before installing or operating the turnstile If the
37. tance If foot grounders are worn outside the ESD protected area testing for functionality before reentry to the ESD protected area should be considered ESD SP9 2 APPENDIX B Foot Grounder Usage Guidance Process monitoring measurements shall be conducted in accordance with a Compliance Verification Plan that identifies the technical requirements to be verified the measurements limits and the frequency at which those verifications shall occur Compliance verification records shall be established and maintained to provide evidence of conformity to the technical requirements The test equipment selected shall be capable of making the measurements defined in the Compliance Verification Plan ANSI ESD S20 20 2007 section 7 3 ANSI ESD 520 20 Table 1 Flooring Footwear Systems Technical Requirements Recommended Range less than 3 5 x 10E7 ohms measured per ANSI ESD STM 97 1 Typical test programs recommend that wrist straps that are used daily should be tested daily However if the products that are being produced are of such value that knowledge of a continuous reliable ground is needed and then continuous monitoring should be considered or even required ESD Handbook ESD TR 20 20 section 5 3 2 4 4 Packaging Turnstile 120VAC SmartLog V5 Turnstile Mounting Bracket Wall Mounting Bracket Connection Cover Dual Independent Foot Plate Foot Plate Cable 6 Power Adapter 12VDC 1 25A center pos DB9 Serial Adapt
38. transformer power switch box so that both welded post anchor tubes are accessible Refer to the photos on the following page for the mounting screw locations Mark the center location of the two anchors See Drawing 1 on the following page Do this by chalking the bottom of one of the all thread shaft rods and running the rod through each of the post anchor tubes welded to the inside of the cabinet Tap the rod gently to mark the concrete for drilling NOTE There are four types of EDC cabinets Standard Extended Bullnose and Extended Bullnose The EDC anchoring footprint is the same regardless of the cabinet type METAL TEMPLATES may be purchased from Alvarado which simplifies this process Move the turnstile and drill a 1 diameter hole at the center of each marked location Drill each hole 3 deep See Drawing 3 on the following page For Terrazzo ceramic tile or brick veneer installations add the thickness of the finished floor material to the anchor hole depth Vacuum out holes thoroughly If the holes are not clean the anchors will not tighten EDC EDCX PUD1535R4 0 T 10 11 12 13 14 15 Insert an anchor into each drilled hole Ensure that the anchors are flush with the concrete floor NOTE Insert anchors with threads down Return the turnstile to the install location Place a cup on each threaded shaft rod Run the cup to the top of the rod See Drawing 2 on the follo
39. tted screwdriver Put the pin back in and retest Test in increments of 1 8 of a turn If the turnstile under rotates returns to standard position very slowly decrease the hydraulic tension Follow directions as above but loosen the adjusting screw turn the adjustment screw counter clockwise Replace the pin and retest The hydraulic cylinder is adjusted at the factory to a level suitable for most standard applications however the viscosity of the hydraulic fluid is affected by extreme variations in temperature Adjustments may be necessary depending on the application or environmental factors When making adjustments ensure that the hydraulic is not adjusted so loosely that the turnstile arm hits the user in the back rear as they pass through the turnstile ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 19 MAINTENANCE continued Lubrication Apply a light grade lubricant i e Tri Flow or 3 in 1 oil with a tube extension applicator to all contact points Contact points include spring contact points Review the graphic on Page 30 for identification of lubrication areas Springs Inspect the springs for unusual wear and replace if worn or damaged When replacing springs use only Alvarado supplied parts Solenoid Do not oil the solenoid plunger The solenoid plunger is designed to have a
40. uently in high use applications and or in dusty or humid environments Periodically check the anchor bolts for tightness Exterior cleaning should be performed as necessary INTERIOR CARE 1 General Remove the turnstile lid and check the tension of the two anchoring shafts Tighten to approximately 80 ft lbs Check tension of all nuts bolts and screws Clean away accumulated dust and dirt Optical Sensors Manually rotate the turnstile and inspect the alignment of the optical sensors The sensor feedback disk should rotate freely between the sensors Tighten the sensor mounting screws if necessary Wiring Inspect all wires and contacts for exposure to any metal parts that may lead to a short Movement Verify that the compression arm and shoe move freely If the movement is not smooth remove both parts and apply 3 in 1 oil Replace parts and check movement Hydraulic Cylinder Verify that the hydraulic cylinder is properly adjusted by observing the rotation of the turnstile arms If the turnstile is electrically controlled first disengage the lock arm in the electrically controlled direction s opin the arm once rapidly in the testing direction The turnstile arm should rotate once and stop in the standard position If the turnstile over rotates increase the hydraulic tension Do this by removing the cotter type pin at the top of the hydraulic closure Tighten the adjusting screw clock wise with a slo
41. ut of contact closure upon turnstile rotation Right Hand Clockwise Direction X5RGY Connection for Entry Lights Left Hand Counter Clockwise Direction Connection for Entry Lights Right Hand Clockwise Direction I CNT Connection for counter reset RESET switch Single throw relay output for connection to Alvarado battery powered digital counter OPTIONAL Support for 5 and 12 VDC LED lights Use jumper JP2 to set voltage If a red green light board is used the red light will be lit when the turnstile is powered and ready for card presentation When a contact is provided to Entry Accept Location ACC the green light illuminates The green light stays on for time out setting or until the turnstile is rotated OPTIONAL Support for 5 and 12 VDC LED lights Use jumper JP2 to set voltage If red green light board is used the red light will be lit when the turnstile is powered and ready for card presentation When a contact is provided to Entry Accept Location ACC the green light illuminates The green light stays on for time out setting or until the turnstile is rotated N O contact connection if blue counter wires are attached to J2 and or J8 connections A 3 position electrical key switch is connected here to provide a reset to the individuals counters ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC ED
42. ut time allowed for an individual to completely travel through the turnstile before the turnstile automatically relocks Used with switch position T4 Always test operation after adjusting to ensure that the set time allowed is compatible with the functionality required for the turnstile Refer to the Entry Time Adjusting Control Switch Settings table below Adjustment control of the maximum throughput time allowed for an individual to completely travel through the turnstile before the turnstile automatically relocks Used with switch position T3 Always test operation after adjusting to ensure that the set time allowed is compatible with the functionality required for the turnstile Refer to the Entry Time Adjusting Control Switch Settings table below NOTE In order to control a Clockwise Lock Arm the solenoid leads MUST be connected to the Clockwise board inputs Likewise in order to control a Counter Clockwise Lock Arm then the solenoid leads MUST be connected to the Counter Clockwise board inputs 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com EDC EDCX PUD1535R4 0 Page 16 Explanation of switch positioned Switch Switch Explanation of switch positioned to left or OFF side Position Position to right or ON side Sets Length of time of contact closure on CNT and COM feedback to 100ms Default Sets Length of time of contact closure on C
43. wing page Run a threaded rod amp cup assembly through one of the welded post anchor tubes seating the rod into the anchor previously inserted into the drilled hole Repeat this process with the other threaded rod amp cup assembly If the turnstile is uneven or rocks shim the turnstile cabinet as necessary Tighten both threaded shaft rods Torque to approximately 40 ft Ibs initially and check the turnstile cabinet for any instability or rocking If the turnstile is still uneven or rocks back off the threaded rods and shim the turnstile cabinet as necessary Once the turnstile is firmly situated torque the threaded shaft rods to 80 ft Ibs Remount the transformer power switch box to the turnstile chassis ALVARADO 12660 Colony Street Chino CA 91710 Phone 1 909 591 8431 Fax 1 909 628 1403 Email information alvaradomfg com Page 6 TURNSTILE INSTALLATION REFERENCE PICTURES AND DRAWINGS Remove the screws as shown to access After removing the mounting screws the obstructed welded post anchor tube carefully move the transformer power switch box to the side and continue installing the turnstile Drawing 1 t 68 6cm gt 1 Post Anchor 3 2cm Tubes 22 1 8 N 27 8 25 4cmj Conduit 22 2cml openings Drawing 3 II Drawing 2 Placement of threaded rod and CONCRETE o O0 ALVARADC Ley Se eee See e Phone 1 909 591 8431
Download Pdf Manuals
Related Search