USER MANUAL - Kramer Electronics
Contents
1. EDID revision 3 Input signal type Digital Color bit depth Undefined Display type RGB color Screen size 1020 x 570 mm 46 0 in Power management Not supported Extension blocs 1 CEA EXT Color characteristics Default color space Non sRGB Display gamma 2 20 Red chromaticity Rx 0 625 Ry 0 340 Green chromaticity Gx 0 280 Gy 0 595 Blue chromaticity Bx 0 155 By 0 070 White point default Wx 0 283 Wy 0 298 Additional descriptors None Timing characteristics Horizontal scan range 15 68kHz Vertical scan rang 50 80Hz Video bandwidth 150MHz CVT standard Not supported GTF standard Not supported Additional descriptors None Preferred timing Yes Native preferred timing 1280x720p at 60Hz Modeline 1280x720 74 250 1280 1390 1430 1650 720 725 730 746 hsync vsync Detailed timing 1 Modeline 1280x720p at 50Hz 16 9 1280x720 74 250 1280 1720 1760 1980 720 725 730 750 hsync vsync Standard timings supported 720 x 400p at 70Hz IBM VGA 640 x 480p at 60Hz IBM VGA 640 x 480p at 67Hz Apple Mac II 640 x 480p at 72Hz VESA 640 x 480p at 75Hz VESA 800 x 600p at 56Hz VESA 800 x 600p at 60Hz VESA 800 x 600p at 72Hz VESA 800 x 600p at 75Hz VESA 1024 x 768p at 60Hz VESA 1024 x 768p at 70Hz VESA 1024 x 768p at 75Hz VESA 1280 x 1024p at 75Hz VESA EIA CEA 8612. Figure 4 Local Area Connection Properties Window 6 Select Use the following IP Address and enter the details as shown in Figure 5 You can use any IP address in the range 192 168 1 1 to 192 168 1 255 excluding 192 168 1 39 that is provided by your IT department 6 1 2 6 2 Internet Protocol TCP IP Properties General the appropriate IP settings Obtain an IP address automatically Use the following IP address Use the following DNS server addresses Preferred DNS server Alternate DNS server IP address 192 168 1 Subnet mask 255 255 255 0 Default gateway 9 0 0 0 You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for 38 Cancel Figure 5 Internet Protocol TCP IP Properties Window 7 Click OK Connecting to the Ethernet Port via a Network Switch Hub To connect to the Ethernet port on the KDS EN1 via a network switch hub e Connect the PC to the Ethernet network switch hub using a straight through cable Connecting the Balanced Unbalanced Stereo Audio Input This section illustrates how to wire the devices to the balanced audio input e A balanced stereo input connection e An unbalanced stereo input connection see Figure 7 see Figure 6 L L G R R Figure 6 Balanced Stereo Audio Connection L L G R R Figure 7 Unbalanced Stere
3. Load Default Load the default configuration Restore Initial Load the factory default configuration Codec Version Displays the codec version 7 3 Changing the Video Input Selection To change the video input selection 1 Press the Enter button to display the menu The menu is displayed 2 Press the Enter button to select the Video Input sub menu The Video Input sub menu is displayed 3 Press the Enter button to enable changing the parameter The current video input selection flashes 4 Using the right or left lt 4 button move through the parameter options until the required video input is displayed 5 Press Enter to save the selection The Updating message flashes for a few seconds and the change is saved Note If the media player does not display correctly following input resolution or selection changes refresh the media player 7 4 To Reset the Device to Factory Default Configuration To reset the device to the factory default configuration 1 Press Enter The menu is displayed Press down repeatedly until the Advanced sub menu is displayed Press Enter to enter the Advanced sub menu The first option in the Advanced sub menu is displayed Press down Y repeatedly until the Restore Initial option is displayed Press Enter The Updating message flashes for a few seconds and the factory defaults are loaded Press Esc twice to exit the menu 8 Operating the
4. left 4 and right buttons to navigate the menu and modify parameters or values 6 ESC Button Press to move back one level through the menu Figure 2 defines the rear panel of the KDS EN1 INPUTS OO 6508 BE to t t F er eee i DGA ODDO OW 42 Figure 2 KDS EN1 HD Video Encoder Streamer Rear Panel Feature Function a z jaan AUDIO Balanced Stereo 5 Pin Terminal Block Connect to the balanced stereo audio source Audio Connector EI EE ASI OUT A BNC Connector 5 Installing the KDS EN1 in a Rack This section provides instructions on rack mounting the KDS EN1 Before installing in a rack be sure that the environment is within the recommended range 0 to 40 C 32 to 104 F 40 to 70 C 40 to 158 F 10 to 90 RHL non condensing OPERATING TEMPERATURE STORAGE TEMPERATURE HUMIDITY T CAUTION When installing on a 19 rack avoid hazards by taking care that 1 Itis located within the recommended environmental conditions as the operating ambient temperature of a closed or multi unit rack assembly may exceed the room ambient temperature 2 Once rack mounted enough air will still flow around the machine 3 The machine is placed straight in the correct horizontal position 4 You do not overload the circuit s When connecting the machine to the sup
5. selection e Resolution e GOP e Encoding mode e Average maximum and minimum bitrates i ee STATUS STATUS Mon Nov 5 10 27 14 UTC 0200 A 2012 Video Setting GOP Audio Setting Mode System Setting Average Bitrate Kbps TS IP Setting Host IP Setting Bex iaren sys Info Min Bitrate Kbps Save Default a Saari Load Default Submit Reset Reset Restore Initial SW Upgrade User Manual Web Site Figure 10 Video Parameters Page For video parameter descriptions see Se 8 1 2 Audio Settings Page The following audio parameters are included e Input port selection e Audio format bitrate and gain Mon Nov 4 UTC 0200 Analog xl MPEG 1 Layerll 2012 Video Setting Audio Setting System Setting TS IP Setting Host IP Setting Sys Info Save Default Load Default Restore Initial SW Upgrade User Manual Web Site Figure 11 Audio Parameters Page For audio parameter descriptions see Section 7 2 2 8 1 3 System Settings Page The following system parameters are included e PMT PID e PCR PID e VID PID e AUD PID e Service name and provider name e TSID e Service ID e Packet size e System bitrate KDS EN1 Operating the KDS EN1 Using the Web Pages System Parameters 0 27 14 UTC 0200 Video Setting Audio Setting System Setting TS IP Setting Host IP Setting Sys Info Save Default Load Default Restore Initia
6. 01 CE audio data formats supported LPCM 2 channel 16 20 24 bit depths at 32 44 48 kHz CE audio data formats supported AC 3 8 channel 448k max bit rate at 32 44 48 88 96 176 192 kHz CE vendor specific data VSDB IEEE registration number 0x000C03 CEC physical address 1 0 0 0 Supports Al ACP ISRC No Supports 48bpp No Supports 36bpp No Supports 30bpp No Supports YCbCr 4 No Supports dual link DVI No Maximum TMDS clock 165MHz Report information Date generated Software revision Data source Operating system 03 02 2013 2 60 0 972 File 6 1 7601 2 Service Pack 1 Raw data 00 FF FF FF FF FF FF 00 2E 4D 19 06 01 00 00 00 09 17 01 03 80 66 39 78 0A 0D C9 A0 57 47 98 27 12 48 4C BF CF 00 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 1D 00 72 51 D0 1A 20 6E 28 55 00 7E 88 42 00 00 14 01 1D 00 BC 52 D0 1E 20 B8 28 55 40 C4 8E 21 00 00 18 00 00 00 FC 00 4B 44 53 20 45 4E 31 20 20 20 20 20 20 00 00 00 FD 00 32 50 0F 44 0F 00 0A 20 20 20 20 20 20 01 EF 02 03 20 70 4C 01 02 04 05 06 0E 10 11 13 14 19 1F 23 09 07 07 23 17 7F 38 66 03 0C 00 10 00 00 01 1D 80 18 71 1C 16 20 58 2C 25 00 C4 8E 21 00 00 9E 01 1D 80 D0 72 1C 16 20 10 2C 25 80 C4 8E 21 00 00 9E 8C 0A D0 90 20 40 31 20 0C 40 55 00 13 8E 21 00 00 18 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 13 8E 21 00 00 18 D6 09 80 A0 20 E0 2D 10 08 60 22 00 12 8E 21 08 08 21 08 08 21 08 08 72 LIMITED WARRANTY The warranty obliga
7. 68 1 1 Stream MAC Sets the physical MAC address Any valid MAC address Default 12 34 56 78 B0 6D Protocol Transport stream protocol selection UDP RTP Pro MPEG Default UDP Destination IP Sets the transport stream destination IP address Any valid IP address Default 226 1 1 1 Destination Port Sets the transport stream destination IP port Any valid IP port Default 1234 IGMP IGMP enable Enable Disable Default Disable FEC Col Offset Sets the FEC col offset From 4 to 16 Default 10 FEC Col NA Sets the FEC col NA From 4 to 16 Default 10 7 2 5 Host IP Sub menu The parameters in the Host IP sub menu display the device network IP parameters Parameter Host IP Sets the IP network address of the device All valid IP addresses Default 192 168 1 21 Host Netmask Sets the IP network mask of the device All valid subnets Default 255 255 255 000 Host Gateway Sets the IP gateway address of the device All valid gateway addresses Default 192 168 1 1 Host MAC Sets the IP port number of the device All valid TCP ports Default 12 34 56 78 B0 6C 7 2 6 Advanced Sub menu The parameters in the Advanced Settings sub menu allow you to save and load configurations reset to factory defaults and display the codec version Parameter Description Save Default Save the current configuration as the default configuration
8. Information Revision number 3 IT underscan Basic audio Supported YCbCr 4 4 4 Supported YCbCr 4 2 2 Native formats Detailed timing 1 Supported 0 1920x1080i at 60Hz 16 9 Modeline 1920x1080 74 250 1920 2008 2052 2200 1080 1084 1094 1124 interlace hsync vsync Detailed timing 2 1920x1080i at 50Hz 16 9 Modeline 1920x1080 74 250 1920 2448 2492 2640 1080 1084 1094 1124 interlace hsync vsync Detailed timing 3 720x576p at 50Hz 4 3 Modeline 720x576 27 000 720 732 796 864 576 581 586 625 hsync vsync Detailed timing 4 720x480p at 60Hz 4 3 Modeline 720x480 27 000 720 736 798 858 480 489 495 525 hsync vsync Detailed timing 5 640x480p at 60Hz 4 3 Modeline 640x480 25 180 640 648 744 800 480 482 484 525 hsync vsync CE video identifiers VICs timing formats supported 640 x 480p at 60Hz Default 4 3 1 1 720 x 480p at 60Hz EDTV 4 3 8 9 1280 x 720p at 60Hz HDTV 16 9 1 1 1920 x 1080i at 60Hz HDTV 16 9 1 1 720 x 480i at 60Hz Doublescan 4 3 8 9 1440 x 480p at 60Hz DVD 4 3 4 9 1920 x 1080p at 60Hz HDTV 16 9 1 1 720 x 576p at 50Hz EDTV 4 3 16 15 1280 x 720p at 50Hz HDTV 16 9 1 1 1920 x 1080i at 50Hz HDTV 16 9 1 1 2880 x 576i at 50Hz Console 4 3 2 15 20 15 1920 x 1080p at 50Hz HDTV 16 9 1 1 NB NTSC refresh rate Hz 1000 10
9. KDS EN1 Using the Web Pages The embedded Web pages can be used to remotely operate the KDS EN1 using a Web browser and an Ethernet connection over a LAN The menu appears on the left side of the screen There are ten Web pages e Video Settings Page see Section 8 1 1 e Audio Settings Page see Section 8 1 2 e System Settings Page see Section 8 1 3 e TS IP Settings Page see Section 8 1 4 e Host IP Settings Page see Section 8 1 5 e System Information Page see Section 8 1 6 e Saving the Default Configuration Page see Section 8 1 7 e Loading the Default Configuration Page see Section 8 1 8 e Load the Factory Defaults Page see Section 8 1 9 e Software Upgrade Page see Section 8 1 10 After making changes on any of the pages click Save to save the changes 8 1 Accessing the KDS EN1 Web Pages To access the KDS EN1 Web pages 1 Open your Internet browser 2 Enter the IP address of the device see Section 10 in the address bar of your browser see Figure 8 le 192 168 1 21 Figure 8 Web Browser Address Bar The home page similar to that shown in Figure 9 appears Kramer KDS EN1 STATUS Mon Nov 5 10 27 14 UTC 0200 2012 Video Setting Audio Setting System Setting TS IP Setting Host IP Setting Sys Info Save Default Load Default Restore Initial SW Upgrade User Manual Web Site Figure 9 Home Page 8 1 1 Video Settings Page The following video parameters are included e Input port
10. KRAMER ELECTRONICS LTD USER MANUAL MODEL KDS EN1 HD Video Encoder Streamer P N 2900 300150 Rev 3 in EN1 HD Video Encoder Streamer Auick Start Guide mE a This guide helps you install and use your product for the first time For more detailed information go to http www kramerelectronics com support product downloads asp to download the latest manual or scan the QR code on the left Step 1 Check what s in the box K KDS EN1 HD Video Encoder Streamer 1 Quick Start Guide Power cord 2 Rack ears 4 Rubber feet Step 2 Install the KDS EN1 Mount the device in a rack using the supplied rack ears or place it on a shelf Step 3 Connect the inputs and outputs Switch off the power to all devices before connecting them to your KDS EN1 CV Balanced DVD Player Player Audio Player Digital Camera Step 4 Connect the power Connect the KDS EN1 to the mains supply using the supplied power cord Step 5 Operate the device Use the keypad to navigate the menu and modify parameters Operate the device usingthe front panel controls and Ethernet 68 mi Press ESC to move back one level in the menu SS Contents 1 Introduction 2 Getting Started 2 1 Achieving the Best Performance 2 2 Recycling Kramer Products 3 Overview 4 Defining the KDS EN1 HD Video Encoder Streamer 5 Ins
11. Long Does this Coverage Last Three years as of this printing please check our Web site for the most current and accurate warranty information Who is Covered Only the original purchaser of this product is covered under this limited warranty This limited warranty is not transferable to subsequent purchasers or owners of this product What Kramer Electronics will do Kramer Electronics will at its sole option provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim under this limited warranty 1 Elect to repair or facilitate the repair of any defective parts within a reasonable period of time free of any charge for the necessary parts and labor to complete the repair and restore this product to its proper operating condition Kramer Electronics will also pay the shipping costs necessary to return this product once the repair is complete 2 Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same function as the original product 3 Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty What Kramer Electronics will not do Under This Limited Warranty If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Krame
12. P Setting Sys Info Save Default Load Default Restore Initial SW Upgrade User Manual Web Site Figure 15 System Information Page 8 1 7 Saving the Default Configuration Page The Save Default page allows you to store the current configuration The message shown in Figure 16 is displayed before the operation is executed Figure 16 Save Default Confirmation Message 8 1 8 Loading the Default Configuration Page The Load Default page allows you to retrieve a previously stored configuration The message shown in Figure 17 is displayed before the operation is executed EI KDS EN 1 Operating the KDS EN1 Using the Web Pages 8 1 10 Sure to Load Default Ce Figure 17 Load Default Confirmation Message Loading the Factory Defaults Page The Restore Initial page allows you to load the factory default parameters The message shown in Figure 17 is displayed before the operation is executed Sure to Restore Initial Figure 18 Restore Initial Settings Confirmation Message Software Upgrade Page The Software Upgrade page allows you to upgrade the firmware of the device Prior to performing this operation you must download the latest firmware version to your PC The latest version is available from http www kramerelectronics com Software Upgrade Select File Browse Figure 19 Software Upgrade Page 9 Technical Specifications INPUTS Digital Video 1 SDI serial video 75
13. Q on SD SMPTE 259M SMPTE 125M 480i 59 94 BNC connectors ITU R BT 656 576i 50 5 HD SMPTE 292 SMPTE 296M 720p 59 94 60 50 SMPTE 274M 1080i 59 94 60 50 1080p 29 97 30 2 23 98 24 23 98sF 24sF 3G SMPTE 424M SMPTE 296M 1080p 59 94 60 50 1 HDMI Analog Video 1 Composite video on a BNC connector 1 Component video Y Pb Pr on 3 BNC connectors Supported resolutions 1920x1080i 50 60Hz 1440x1080i 50 60Hz 1280x720p 50 60Hz 720x480i 60Hz 720x576i 50Hz Analog Audio 1 Stereo balanced audio on a 5 pin terminal block OUTPUTS Digital Video 2 DVB ASI on BNC connectors Max data rate 72Mbps 188 bytes IP 1 IP UDP transport stream on an RJ 45 connector CONTROL 1 TCP IP on an RJ 45 Connector POWER CONSUMPTION 100 240V AC 50 60Hz 24VA OPERATING TEMPERATURE 0 to 40 C 32 to 104 F STORAGE TEMPERATURE 40 to 70 C 40 to 158 F HUMIDITY 10 to 90 RHL non condensing DIMENSIONS 19 x 9 41 x 1U W D H rack mountable WEIGHT 1 8kg 3 97Ibs approx ACCESSORIES Power cord rack ears 10 Default Communication Parameters Ethernet IP Address 192 168 1 39 255 255 2550 Default gateway 0 0 0 0 11 Default EDID Monitor Model name KDS EN1 Manufacturer KRM Plug and Play ID Serial number Manufacture date KRM0619 1 2013 ISO week 9 None
14. SDI composite and component video signals HDMI and balanced audio signals which are output as an IP stream and as a DVB ASI signal All mentions of SDI in this manual include signals up to and including 3G HD SDI Note If the content is protected by HDCP the stream is not encoded The KDS EN1 features e A maximum data rate of 3Gpbs e One SDI video one HDMI one composite and one component video input e One balanced stereo audio input e One TCP IP output e Two ASI outputs e The option to select either the embedded audio or to embed two independent audio groups e An LCD text display for easy configuration and operation 4 Defining the KDS EN1 HD Video Encoder Streamer Figure 1 defines the front panel of the KDS EN1 DOD ao status O HD Video Encoder Streamer KDS EN1 Figure 1 KDS EN1 HD Video Encoder Streamer Front Panel LCD Readout Displays either the input output resolution currently selected or the menu during configuration EB ON LED Lights green when the device is powered on LOCK LED Lights orange when the front panel buttons are locked Lights green when the buttons are unlocked see Section 7 1 STATUS LED Lights green to indicate that the device is working correctly and that there is a valid input signal Lights red to indicate a device fault or if there is no valid input signal 5 Menu Navigation Buttons Press the Enter up 4 down
15. TIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPICABLE LAW IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A CONSUMER PRODUCT UNDER THE MAGNUSON MOSS WARRANTY ACT 15 U S C A 2301 ET SEQ OR OTHER APPICABLE LAW THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU AND ALL IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW Other Conditions This limited warranty gives you specific legal rights and you may have other rights which vary from country to country or state to state This limited warranty is void if i the label bearing the serial number of this product has been removed or defaced ii the product is not distributed by Kramer Electronics or iii this product is not purchased from an authorized Kramer Electronics reseller If you are unsure whether a reseller is an authorized Kramer Electronics reseller please visit our Web site at www kramerelectronics com or contact a Kramer Electronics office from the list at the end of this document Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the online product registration form Kramer Electronics thanks you for purchasing a Kramer Electronics product We hope it will give you years of satisfact
16. cting the Ethernet port you have to install and configure your Ethernet Port For detailed instructions see the Ethernet Configuration Guide Lantronix in the technical support section on our Web site http www kramerelectronics com Connecting the Ethernet Port directly to a PC You can connect the Ethernet port on the KDS EN1 to the Ethernet port on your PC via a crossover cable with RJ 45 connectors This type of connection is recommended for identification of the factory default IP Address of the KDS EN1 during the initial configuration To configure your PC after connecting the Ethernet port 1 Right click the My Network Places icon on your desktop 2 Select Properties 3 Right click Local Area Connection Properties 4 Select Properties The Local Area Connection Properties window appears 5 Select the Internet Protocol TCP IP and click the Properties Button 4 Local Area Connection Properties General Advanced Connect using E9 Intel R 82566DC 2 Gigabit Network C This connection uses the following items v Client for Microsoft Networks v 2 File and Printer Sharing for Microsoft Networks v 2 QoS Packet Scheduler v 7 Internet Protocol TCP IP Description Allows pour computer to access resources on a Microsoft network C Show icon in notification area when connected Notify me when this connection has limited or no connectivity
17. d that this product should be returned directly to Kramer Electronics this product should be properly packed preferably in the original carton for shipping Cartons not bearing a return authorization number will be refused Limitation on Liability THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE PRODUCT TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION OR UNDER ANY OTHER LEGAL THEORY Some countries districts or states do not allow the exclusion or limitation of relief special incidental consequential or indirect damages or the limitation of liability to specified amounts so the above limitations or exclusions may not apply to you Exclusive Remedy TO THE MAXIMUM EXTENT PERMITTED BY LAW THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES REMEDIES AND CONDITIONS WHETHER ORAL OR WRITTEN EXPRESS OR IMPLIED TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT INCLUDING WARRAN
18. e KDS EN1 Always switch off the power to any device before connecting it to your KDS EN1 After connecting your KDS EN1 connect its power and then switch on the power to the other devices Composite Video Player Balanced Audio Player gt in A SY Video SS Camcorder H 264 Decoder IP Set Top PC Box Figure 3 Connecting the KDS EN1 HD Video Encoder Streamer To connect the KDS EN1 as illustrated in the example in Figure 3 1 Connect the composite video source for example a composite video player to the CV INPUT BNC connector 2 Connect the balanced audio source for example a balanced audio player to the AUDIO INPUT 5 pin terminal block 6 1 6 1 1 3 Connect the SDI source for example a video camcorder to the SD HD SDI INPUT BNC connector 4 Connect the HDMI source for example a DVD player to the HDMI INPUT connector 5 Connect the ASI OUT A BNC connector to the ASI acceptor for example an H 264 decoder 6 Connect the IP OUT RJ 45 connector to the IP acceptor for example an IP set top box 7 Optional Connect a PC controller via a LAN to the CONTROL RJ 45 Ethernet connector Connecting to the KDS EN1 via Ethernet You can connect the KDS EN1 via Ethernet via either of the following methods e A crossover cable see Section 6 1 1 for direct connection to the PC e A straight through cable see Section 6 1 2 for connection via a network hub or network router After conne
19. ectronics Since 1981 Kramer Electronics has been providing a world of unigue creative and affordable solutions to the vast range of problems that confront video audio presentation and broadcasting professionals on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Routers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters and GROUP 11 Sierra Video Products Congratulations on purchasing your KDS EN1 HD Video Encoder Streamer which is ideal for broadcast and production studios as well as digital analog AV authoring 2 2 1 Getting Started We recommend that you Unpack the eguipment carefully and save the original box and packaging materials for possible future shipment Review the contents of this user manual Use Kramer high performance high resolution cables Use only the power cord supplied with the device Go to http www kramerelectronics com to check for up to date user manuals application programs and to check whether firmware upgrades are available where appropriate Ach
20. ieving the Best Performance To achieve the best performance Use only good guality connection cables to avoid interference deterioration in signal guality due to poor matching and elevated noise levels often associated with low guality cables Do not secure the cables in tight bundles or roll the slack into tight coils Avoid interference from neighboring electrical appliances that may adversely influence signal guality Position your Kramer KDS EN1 away from moisture excessive sunlight and dust This eguipment is to be used only inside a building It may only be connected to other eguipment that is installed inside a building 2 2 Recycling Kramer Products The Waste Electrical and Electronic Eguipment WEEE Directive 2002 96 EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by reguiring it to be collected and recycled To comply with the WEEE Directive Kramer Electronics has made arrangements with the European Advanced Recycling Network EARN and will cover any costs of treatment recycling and recovery of waste Kramer Electronics branded eguipment on arrival at the EARN facility For details of Kramer s recycling arrangements in your particular country go to our recycling pages at http Avww kramerelectronics com support recycling Overview The KDS EN1 HD Video Encoder Streamer is ideal as a broadcast quality video scaler and audio embedder de embedder for digital signals up to 3G HD
21. ion For the latest information on our products and a list of Kramer distributors visit our Web site where updates to this user manual may be found We welcome your guestions comments and feedback Web site www kramerelectronics com KRAMER E mail info Okramerel com SAFETY WARNING Disconnect the unit from the power m supply before opening and servicing P N 2900 300150 Rev 3
22. l SW Upgrade User Manual Web Site Figure 12 System Parameters Page For system parameter descriptions see Section 7 2 3 8 1 4 TS IP Settings Page The following TS IP parameters are included e Stream IP netmask and gateway e MAC address e Protocol e Destination IP and port e Enable disable IGMP e FEC column offset e FEC column Na number EI KDS EN1 Operating the KDS EN1 Using the Web Pages TS IP Parameters 192 168 1 22 192 168 1 1 Video Setting Audio Setting System Setting TS IP Setting Host IP Setting Sys Info Save Default Load Default Restore Initial SW Upgrade User Manual Web Site Figure 13 TS IP Parameters Page For TS IP parameter descriptions see Section 7 2 4 8 1 5 Host IP Settings Page The following host IP parameters are included e Host IP netmask and gateway e MAC address 192 168 1 21 Video Setting 192 168 1 1 Audio Setting System Setting TS IP Setting Host IP Setting Sys Info Save Default Load Default Restore Initial SW Upgrade User Manual Web Site Figure 14 Host IP Parameters Page For host IP parameter descriptions see Section 7 2 5 KDS EN1 Operating the KDS EN1 Using the Web Pages 8 1 6 System Information Page The following system details are displayed all fields are read only e Device and model name e Hardware and software versions e IP address e Device status System Information System Setting TSIP Setting Host I
23. o Audio Connection TA 7 2 Operating the KDS EN1 Using the Front Panel Buttons Approximately 30 seconds after powering on the KDS EN1 the model name firmware version and serial number of the device is displayed standby display When this display appears you can operate the KDS EN1 via ether the front panel buttons or remotely using Ethernet over a LAN see Section 8 Unlocking the Front Panel Buttons After approximately 30 seconds of no button activity the front panel buttons are locked and the Lock LED lights orange To unlock the front panel buttons 1 Press Enter twice in quick succession 2 Immediately press Esc twice in quick succession The front panel buttons are unlocked and the Lock LED lights green Using the Menu The menu is shown on the display when the Enter button is pressed If there is no button activity for approximately 30 seconds display reverts back to the standby display Navigation through the menu is performed as follows e Enter display the menu select a parameter value save a value e Up A or Right gt scroll up through the parameter value list e Down or Left lt scroll down through the parameter value list e ESC Move up one level through the menu or exit the menu if at the first menu level 7 24 The main menu comprises six sub menus e Video see Section 7 2 1 e Audio see Section 7 2 2 e System see Section 7 2 3 e TS IP see Section 7 2 4 e H
24. ost IP see Section 7 2 5 e Advanced see Section 7 2 6 Video Sub menu The parameters in the Video sub menu set the video characteristics Parameter Video Input Video input port selection CVBS YPbPr HDMI SDI Default CVBS Video The current video signal resolution 1920x1080p 50 60Hz Resolution not supported by component input 1920x1080i 50 60Hz 1440x1080i 50 60Hz 1280x720p 50 60Hz 720x480i 60Hz 720x576i 50Hz Video GOP Video GOP selection IBBP IPPP IBP Default IBBP Video Bit Video bit rate mode selection CBR VBR Mode Average Sets the average video bitrate This is From 1000Kbps to BitRate only valid when in VBR mode and must 19999Kbps be more than the average video bitrate Max BitRate Sets the maximum video bitrate This is From 10000Kbps to VBR only valid when in VBR mode and must 19999Kbps be more than the average video bitrate Min BitRate Sets the minimum video bitrate This is From 1000Kbps to VBR only valid when in VBR mode and must 7999Kbps be less than the average video bitrate 7 2 2 7 2 3 Audio Sub menu The parameters in the Audio sub menu set the audio characteristics Parameter Audio Input Audio input source selection Analog HDMI SDI Default Analog Audio Format Audio format selection MPEG I Layer II S PDIF AC3 Default MPEG Audio BitRate Audio bitrate selection 32Kbps 64Kbps 128Kbps 192Kbps 256Kbp
25. ply circuit overloading the circuits might have a detrimental effect on overcurrent protection and supply wiring Refer to the appropriate nameplate ratings for information For example for fuse replacement see the value printed on the product label 5 The machine is earthed grounded in a reliable way and is connected only to an electricity socket with grounding Pay particular attention to situations where electricity is supplied indirectly when the power cord is not plugged directly into the socket in the wall for example when using an extension cable or a power strip and that you use only the power cord that is supplied with the machine To rack mount a machine 1 Attach both ear brackets to the machine To do so remove the screws from each side of the machine 3 on each side and replace those screws through the ear brackets 2 Place the ears of the machine against the rack rails and insert the proper screws not provided through each of the four holes in the rack ears Note In some models the front panel may feature built in rack ears Detachable rack ears can be removed for desktop use Always mount the machine in the rack before you attach any cables or connect the machine to the power e If you are using a Kramer rack adapter kit for a machine that is not 19 see the Rack Adapters user manual for installation instructions available from our Web site 6 Connecting th
26. r Electronics products this product must be insured during shipment with the insurance and shipping charges prepaid by you If this product is returned uninsured you assume all risks of loss or damage during shipment Kramer Electronics will not be responsible for any costs related to the removal or re installation of this product from or into any installation Kramer Electronics will not be responsible for any costs related to any setting up this product any adjustment of user controls or any programming required for a specific installation of this product How to Obtain a Remedy under this Limited Warranty To obtain a remedy under this limited warranty you must contact either the authorized Kramer Electronics reseller from whom you purchased this product or the Kramer Electronics office nearest you For a list of authorized Kramer Electronics resellers and or Kramer Electronics authorized service providers please visit our web site at www kramerelectronics com or contact the Kramer Electronics office nearest you In order to pursue any remedy under this limited warranty you must possess an original dated receipt as proof of purchase from an authorized Kramer Electronics reseller If this product is returned under this limited warranty a return authorization number obtained from Kramer Electronics will be required You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product Ifitis decide
27. s 320Kbps 384Kbps Default 384Kbps Audio Gain Audio gain selection 12dB 6dB OdB 6dB 12dB Default 0dB System Sub menu The parameters in the System sub menu display the system parameters Parameter PMT PID Sets the video output PMT PID From 50 to 7999 Default 101 PCR PID Sets the video output PCR PID From 100 to 8190 Default 102 VID PID Sets the video output PID From 100 to 7999 Default 103 AUD PID Sets the audio output PID From 100 to 7999 Default 104 TSID Sets the transport stream ID From 0 to 59999 Default 1 Service ID Sets the output service ID From 1 to 59999 Default 1 Service Name Sets the service name Textual name Default TV1 Provider Name Sets the service provider name Textual name Default TV Channel Packet Size Packet size selection 188 204 FEC OFF 204 FEC ON Default 188 System Bitrate Sets the system bitrate From 2000Kbps to 19999Kbps Default 9500Kbps 7 2 4 TS IP Sub menu The parameters in the TS IP sub menu set the transport stream IP parameters Parameter Stream IP Sets the transport stream IP address Any valid IP address Default 192 168 001 022 Stream Netmask Sets the transport stream network mask address Any valid netmask IP address Default 255 255 255 0 Stream Gateway Sets the transport stream gateway address Any valid gateway IP address Default 192 1
28. talling the KDS EN1 in a Rack 6 Connecting the KDS EN1 6 1 Connecting to the KDS EN1 via Ethernet 6 2 Connecting the Balanced Unbalanced Stereo Audio Input 7 Operating the KDS EN1 Using the Front Panel Buttons 7 1 Unlocking the Front Panel Buttons 7 2 Using the Menu 7 3 Changing the Video Input Selection 7 4 To Reset the Device to Factory Default Configuration 8 Operating the KDS EN1 Using the Web Pages 8 1 Accessing the KDS EN1 Web Pages 9 Technical Specifications 10 Default Communication Parameters 11 Default EDID Figures Figure 1 KDS EN1 HD Video Encoder Streamer Front Panel Figure 2 KDS EN1 HD Video Encoder Streamer Rear Panel Figure 3 Connecting the KDS EN1 HD Video Encoder Streamer Figure 4 Local Area Connection Properties Window Figure 5 Internet Protocol TCP IP Properties Window Figure 6 Balanced Stereo Audio Connection Figure 7 Unbalanced Stereo Audio Connection Figure 8 Web Browser Address Bar Figure 9 Home Page Figure 10 Video Parameters Page Figure 11 Audio Parameters Page Figure 12 System Parameters Page Figure 13 TS IP Parameters Page Figure 14 Host IP Parameters Page Figure 15 System Information Page Figure 16 Save Default Confirmation Message Figure 17 Load Default Confirmation Message Figure 18 Restore Initial Settings Confirmation Message Figure 19 Software Upgrade Page ao i ja ja a al i OO NNWWBW OO SAI GI RR ON N NN NY oN O Introduction Welcome to Kramer El
29. tions of Kramer Electronics for this product are limited to the terms set forth below Whatis Covered This limited warranty covers defects in materials and workmanship in this product What is Not Covered This limited warranty does not cover any damage deterioration or malfunction resulting from any alteration modification improper or unreasonable use or maintenance misuse abuse accident neglect exposure to excess moisture fire improper packing and shipping such claims must be presented to the carrier lightning power surges or other acts of nature This limited warranty does not cover any damage deterioration or malfunction resulting from the installation or removal of this product from any installation any unauthorized tampering with this product any repairs attempted by anyone unauthorized by Kramer Electronics to make such repairs or any other cause which does not relate directly to a defect in materials and or workmanship of this product This limited warranty does not cover cartons equipment enclosures cables or accessories used in conjunction with this product Without limiting any other exclusion herein Kramer Electronics does not warrant that the product covered hereby including without limitation the technology and or integrated circuit s included in the product will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used How
Download Pdf Manuals
Related Search