Now
Contents
1. Laipac All In One Utility 2012 p LAPAC TECH LAIPAC TECH mE StarFinder Configuration Utility SETUP SYSTEM Ifo APPLICATIONS Phone Numbers Ser Assistance Number 9057621228 Emergency Number 1 9057621228 SMS Base Station Number 905762 1228 Assistance Number When user presses the Panic button on 10 pin I O cable the number programmed into the Assistance Number field will be dialled Emergency No 1 If this number is set up and unit will send SMS message to the SMS device with this No under conditions below a User presses the Panic button on 10 pin I O cable or b Unit is triggered by Towing Alert or Accident Alert c Emergency No 1 sending function related to these alerts are enabled SMS Base Station The SMS Base Station Number is used when the Starfinder Lite is operating under SMS mode All of the waypoints and alert messages will be sent to the SMS Base Station Number This number also can belong to a cell phone an SMS modem or any SMS device Once this No is set up device only accept the command sent by SMS device with this No Note To use the Assistance Number for doing phone call user s SIM card must be with valid Voice Plan 2012 2021 by Laipac Technology Inc All Rights Reserved Page 21 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide SYSTEM gt Server Query r LocationNow Suite LAIPAC Bente LAIPAC TECHNOLOGY2. ee FILE SETUP SYSTEM Incoming Call Auto Answer LAIPAC TECHNOLOGY INC StarFinder Configuration Utility APPLICATIONS Default Enable Default Disable S Default Auto Answer FALL BACK MODE GPRS gt SMS Wireless Data Plan GPRS SMS Wireless Voice Plan Voice Incoming Call 2012 2021 by Laipac Technology Inc All Rights Reserved Fig 3 4 2 b This section governs the default GSM connection settings or what the unit will connect to first If you are using LocationNow tracking services this must be enabled GPRS mode tells the device it will be transmitting its information across the internet If you are tracking service based on Short Message System rather than LocationNow SMS mode should be enabled It tells the device to transmit its information to another SMS device This section initializes the voice option in the StarFinder Lite Originally this setting is designed to tell unit if the existing SIM card is with voice calling enabled Currently unit has enabled this setting actively Of course if you are using SIM card without Voice Plan no calling or voice communication can be accomplished This setting determines whether or not the unit will automatically answer incoming calls As prerequisite Voice must be enabled first Page 12 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide F
3. 10 browser only which being supported by Adobe Flash Player V9 0 or up For Adobe Flash Player V9 0 or up user has to download it by using Windows IE and the link below rather than downloading it through any other browser http get adobe com flashplayer 3 3 2 Installation of utility software This software package is a compressed file with suffix 7z or zip such as LocationNowSuite20131009 7z Decompress it to get the executable program LocationNowSuite20131009 exe Run LocationNowSuite20131009 exe Follow Setup Wizard instruction click Next step by step user can complete the installation of this utility software 3 3 3 Installation of USB driver Depending on what kind of Microsoft Windows Operating System being used on user s computer the installation of USB driver procedure is different User could find all those detail in Quick Start Manual version 2 4 section 2 2012 2021 by Laipac Technology Inc All Rights Reserved Page 10 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 3 4 Configuration of StarFinder Lite 3 4 1 Start configuration of your device Refer to Quick Start Manual s section 4 How to start configuration of your unit 3 4 2 Basic Configuration To ensure user s unit is able to access remote server such as Laipac s LocationNow service platform some basic setting items are requested and described in this sectio
4. SIM PIN Number E Recent PI Oe ERENT gt user manaual V13 30 11 2013 3 56PM File folder 3 Librari 3 SF Lite configuration 1 30 11 2013 Microsoft Office raries 4 ibrari Gz zmfSF Lite test 2013 11 25 25 11 2013 11 08 Microsoft Office Documents d Music Pictures F E Videos amp Homegroup Computer amp Local Disk C a RECOVERY D _ Filename SF Lite configuration 1 X Config Files cfg z Open v Cancel Ir Fig 3 4 4b b From the existing files to select a prefer one such as SF Lite configurati 1 then click Open If reading file is successful user can see a pop up window with prompt Success 2012 2021 by Laipac Technology Inc All Rights Reserved Page 17 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide Save the current configuration into a configuration file User can save the current edited configuration into to a configuration file follow the steps below c Click FILE gt Save see Fig 3 4 4c and Fig 3 4 4d mre StarFinde guration Utility Q Importdefaultfile S7 1 o APPLICATIONS Import file i Save file lt Hardware Configuration 1 00 Device ID 10001002 Default 99999999 Password o0000000 Default 00000000 GSM Band 850 1900 m SIM PIN Number Disable v Default Disable Fig 3 4 4c Importdefault file 7 I 0 APPLICATI
5. unit e Insert a valid SIM card into unit and power up the unit with DC power supply 12V e Reset unit with reset button to start running application Read the setting from units By clicking Read Setting from Device button user can read the reside configuration from the unit which being connected to the running utility If unit has never been configured and valid its configuration this reading configuration operation will be failure 2012 2021 by Laipac Technology Inc All Rights Reserved Page 16 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 3 4 4 Acquire setting from or save setting into a configuration file Acquire setting from a existing configuration file User can acquire a set of configuration from a saved configuration file on his computer a Click FILE gt Import file see Fig 3 4 4a and 3 4 4b FILE StarFinder Configuration Utility f moortaetautnie AY o APPLICATIONS Hardware Configuration Device ID 19001002 Default 99999999 Password 00000000 Default 00000000 GSM Band 850 1900 lt SIM PIN Number Disable v Default Disable Fig 3 4 4a APPLICATIONS Save file Logout 3 Hardware Configuration 1 0 OO bo Laipac Project SF Lite201 gt 44 Search SF Lite 201 Device ID Password Organize New folder Resale B Downloads Name i Date modified Type
6. A 0183 output The GSM antenna may be mounted almost anywhere as the GSM signal is generally very strong The GPS antenna however should be mounted somewhere with a clear line of sight to the sky under dash board or at least in a position not surrounded by metal If you are having trouble receiving either signal try relocating the antenna Another consideration is if user wants to get high quality Audio performance please keep distance SF_Lite unit with electromagnetic noise source 5 2 4 Other Options The Starfinder Lite comes with many other options which may need installation There are 2 optically isolated inputs 3 Relay outputs and 1 analog port which may need to be connected and would rely on the specific application for installation details A certified car audio security installer should be familiar with connecting the relays to door locks or starter triggers The specs and considerations for these other features can be found later in this section 2012 2021 by Laipac Technology Inc All Rights Reserved Page 34 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 5 2 5 Power Connector Power PEE m The main Power supply voltage could work in the range of 9 36V Typical power consumption of the Starfinder Lite is 1W with peaks up to 5 5W The current drawn is a result of power over voltage thus a low voltage power supply will need to provide more current 5 2 6 Buttons Input Output Input BI
7. INC FILE StarFinder Configuration Utility SETUP SYSTEM I 0 APPLICATIONS Report Data Logger Phone Numbers SERVER QUERY Active Enable w Default Enable Query Interval o bel hr 10 al min Default 15 mins Server Query Used as a GSM keep alive and tests the connection status of the Starfinder Lite This setting must be enabled first Query Interval The time interval in which the Starfinder Lite tests the GPRS and TCP IP connection between the server and itself If server does not respond to the connection checking message sent out by Starfinder Lite the unit will enter into re develop connection process 2012 2021 by Laipac Technology Inc All Rights Reserved Page 22 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide SYSTEM gt Data Time r LocationNow Suite PPLAiPac TECH m FILE pe SETUP SYSTEM 1 0 APPLICATIONS Report Data Logger PhoneNumbers Server Query TIME ZONE amp DSP Time Zone GMT 05 00 Eastern Time USA amp Canada Daylight Saving Time Enable v Default Enable DST Start Date Mar Second Sun X DST End Date Nov v First X Sun v LAIPAC TECHNOLOGY INC StarFinder Configuration Utility Time Zone Use this to select your time zone so that the device knows your local time Daylight Savings Time Use this to enable the daylight savings time start and en
8. Input 1 See section 4 3 F O Note Trigger Value The G Sensor Trigger Value has a default value of 5Gs and should be kept as a recommended value to sense a vehicle collision as opposed to a pot hole 2012 2021 by Laipac Technology Inc All Rights Reserved Page 30 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 5 HARDWARE DETAILS amp INSTALLATION The Starfinder Lite is enclosed in a robust metal case and can withstand intensive shock and temperature environments The features on the front of the unit include a SIM card tray a USB port the reset button speaker and microphone jacks 2 female SMA connectors for the GPS and GSM antennas and three LEDs to show the status of reporting and connectivity as shown in the below image amp GPS GSM SIM The connections available on the back of the unit include two optically isolated inputs and three Relay outputs in the main I O section labeled as 12V one analog input and the TTL I O ports used for the call answer button labeled as 3 5V a wide power supply input range of 9 36V and RS232 interface as shown in the below image Note Please refer to sections 5 1 5 through 5 1 9 for detailed electrical specifications RS232 I O e Y9 12V E ee 2012 2021 by Laipac Technology Inc All Rights Reserved Page 31 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 5 1 Specification 5 1 1 GPS E
9. MART LOG Smart Log Report Fig 3 4 2 d Report and its setting This option allows you to specify how frequent the unit will send a position update You can specify the report by time value in hours minutes and seconds Also user can specify the report by distance value in kilometres miles or yards 2012 2021 by Laipac Technology Inc All Rights Reserved Page 15 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 3 4 3 Save setting into or read setting from the device r LocationNow Suite o LAIPAC maini LAIPAC TECHNOLOGY INC m FILE StarFinder Configuration Utility SETUP SYSTEM 1 0 APPLICATIONS Device ID 1000 Services Network Firmware Version 12020800 Serial Number 357322041165678 Memory Size 160 KB Hardware Configuration 1 00 Device ID 10001002 Default 99999999 Password 00000000 Default 00000000 GSM Band 850 1900 X SIM PIN Number Disable v Default Disable Information Read current setting Success Write new setting Success Save setting into unit and valid it Once user complete the configuration he should click Save All Setting to Device button to save the edited setting into unit if this saving process is OK Operator should see the pop up window with prompt Writing new setting Success To valid this configuration user needs e Disconnect computer with
10. O2 GND CH GED HHHH oo Output BIOS Input BIO1 These four connections are used by the StarFinder Lite Button Analog cable set If you are using these without the standard cable set the following summarizes the use of these connections Input BIO1 Active LOW will start answer or end a phone call if enabled Input BIO2 Active LOW will send a Panic report to LocationNow if enabled Output BIO3 Normally LOW indicates phone call status used to drive LED GND Common Ground The inputs are standard 3 3V to signal a logical HIGH and tolerant up to 5V exceeding 5V can damage your StarFinder Lite 2012 2021 by Laipac Technology Inc All Rights Reserved Page 35 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 5 2 7 Analog Input Analog GND Analog Input Input voltage 0 3 3V Resolution 10 bit Sample Time 100ms Analog Input When enabled the analog port is used to measure input voltage from 0 3 3V and will send an alert when the voltage exceeds the level specified in your configuration The Analog input is tolerant up to 5V exceeding 5V can damage your StarFinder Lite Analog GND This is the ground reference for the Analog Input signal 5 2 8 Optically Isolated Inputs Input 1 Input 2 HEH Input 2 Input 1 The positive wires are the sensing wires or wires that detect the voltage changes and the negative wires are for common ground
11. ONS Import file ork it 9800 Hardware Configuration 1 0 Save As JU E Leipac Project SF Lite 201 4 Search SF Lite 201 Device ID 1g VJ Password oog Organize v New folder GSM Band Name zs Date modified Type SIM PIN Number D Librarie me eat p Ji user manaual V13 30 11 20134 15PM_ File folder L Document a Musi as SF Lite configuration 1 30 11 20134 05PM Microsoft Office jusic E3 zmfSF Lite test 2013 11 25 25 11 2013 11 08 Microsoft Office E Pictures B Videos e Homegroup 1 Computer Local Disk C eas RECOVERY OS Ply Filename C Laipac Project SF Lite 201 SF Lite configuration 2 Save as type Config Files cfg Hide Folders Save Cancel Fig 3 4 4d d User should type in the name of this new configuration file such as configuration 2 then click Save 2012 2021 by Laipac Technology Inc All Rights Reserved Page 18 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 4 Advanced Configuration and Features This section introduces all other configuration settings not covered by section 3 4 2 Basic Configuration Those settings can be categorized into 4 major parts SETUP SYSTEM I O and APPLICATION Among them SYSTEM settings are concerned with reporting and voice setup T O settings are used for customizable I O functionality The APPLICATION settings are used for other types of even
12. RS the saved messages will be sent to remote server actively Automatically this function has been always enabled by unit User can skip this setting 2012 2021 by Laipac Technology Inc All Rights Reserved Page 19 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide SYSTEM gt Data Logger r LocationNow Suite a p LAPAC TECH LAIPAC TECHNOLOGY INC FILE StarFinder Configuration Utility po SETUP SYSTEM 1 0 APPLICATIONS Report Phone Numbers Server Query Data Time DATA LOGGER Waypoints amp Events Log Disable v Default Disable By Time Interval By Distance Interval Memory Full Alert Disable v Default Disable Waypoint Log Waypoints amp Events Log setting gives you the option to log or store waypoint and alert messages in the unit s internal memory By Time Interval Logs messages into internal memory based on the specified time interval By Distance Interval Logs messages into internal memory based on the specified distance interval Memory Full Alert Data Logger Memory Full alert will cause the unit to send an alert when the internal memory of the unit is full This means that once the unit runs out of memory an alert will be sent to the GPRS server 2012 2021 by Laipac Technology Inc All Rights Reserved Page 20 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide SYSTEM gt Phone Number
13. StarFinder Lite User s Manual amp Reference Guide LAIPAC TECH Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide Federal Communications Commission FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Consult the dealer or an experienced installer for help You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment FCC RF Radiation Exposure Statement 1 This Transmitter must not be co located or operating in conjunction with any other antenna or transmit
14. The positive wires are most commonly connected to solenoid wires that drive ignition horn air conditioning gas cap door open closed status etc When the inputs are enabled they will send an alert when the specified condition is met and all have the same electrical characteristics and behavioural options 2012 2021 by Laipac Technology Inc All Rights Reserved Page 36 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide Electrical Logic Levels Characteristics Minimum Maximum Voltage Amperage Voltage Amperage Logical HIGH 3 5V 1 3mA 18V 6 7mA Logical LOW OV OmA 1 5V 1 1mA Note An input level exceeding 19V could damage the StarFinder Lite and should be avoided 5 2 9 Three Relay Outputs Output3P Output2P Output1P HEH Output1N Output2N Output3N The Starfinder Lite has three relay outputs which can be remotely controlled by the control center All three outputs have the same electrical characteristics and behavioral options The outputs serve as a switch either to drive an external relay or to open close an existing low amperage circuit Follow the electrical characteristics chart below or damage may be incurred to both unit and vehicle Also review page 30 for the output behavior Electrical Characteristics Maximum Allowable Voltage Maximum Allowable Current AC 125 V 0 5A DC 60 V 0 3A DC 30 V 1A The switch status o
15. UCTION 2 FEATURES 3 INITIAL SETUP 3 1 3 2 3 3 What you will need Setup Summary Installing the StarFinder Lite Software Introduction to utility software 10 10 Installation of utility software 10 Installation of USB driver 10 Configuration of StarFinder Lite Start configuration of your device 11 11 Basic Configuration 11 Save setting into or read setting from the device 16 Acquire setting from or save setting into a configuration file 17 4 ADVANCED CONFIGURATION AND FEATURES__ 19 4 1 4 2 4 3 4 4 5 5 1 Setup Settings System Settings Input Output Settings Application Settings HARDWARE DETAILS amp LAYOUT Specifications 2012 2021 by Laipac Technology Inc All Rights Reserved 19 19 24 29 31 32 Page 4 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 5 1 1 5 1 2 5 1 3 5 1 4 5 2 5 21 5 2 2 5 2 3 5 2 4 5 2 3 5 2 6 5 2 7 5 2 8 5 2 9 6 1 6 2 6 3 6 4 6 5 GPS Engine Specs 32 GSM Modem Specs 32 GPS Antenna Specs 33 GSM Antenna Specs 33 Installation 34 Required Hardware 34 Installing your Starfinder Lite 34 Considerations 34 Other Options 34 Power Connector 35 Buttons Input Output 35 Analog Input 36 Optically Isolated Inouts 36 Three Relay Outputs 37 6 OPERATION 38 LED Operation 38 Position Reporting by Event 38 Position Reporting by Reque
16. Yes SIM Pin Number No No Yes Time Zone No No Yes GPRS Mode No Yes Yes SMS Mode No Yes Yes Voice No No Enabled Incoming call No No Yes GPRS to SMS fall back No No Yes APN APN username No Yes Yes APN Password No Yes Yes Domain name la No No Yes Port la No Yes Yes Static IP 1 No Yes Yes Port 1 No No Yes Domain name 2a No No Yes Port 2a No No Yes Static IP 2 No No Yes Port 2 No No Yes DNS IP 1 No Yes Yes DNS IP 2 No Yes Yes Report by time Yes Yes Yes Report by distance Yes Yes Yes Smart Log No No Enabled Air time green mode No No Yes Waypoints amp Events Log Log by Time Interval No Yes Yes Log by Distance Interval No Yes Yes Data Logger Memory Full Alert No No Yes Assistance Number Yes Yes Yes Emergency Number 1 Yes Yes Yes Emergency Number 2 Reserved Reserved Reserved 2012 2021 by Laipac Technology Inc All Rights Reserved Page 40 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide SMS Base Station Number No Yes Yes Server Query Selection No No Yes Server Query Interval No Yes Yes Input 1 as No No Yes Alert when Ignition on off No No Yes Counter 1 Starting Value No No Yes Alert when Counter 1 Reaches No No Yes Input 2 as No No Yes Alert when Door open close No No Yes Counter 2 Starting Value No No Yes Alert when Counter 2 Reaches No No Yes Output 1 as No No Yes Starter Control on off No No Yes Timer Control 1 Value No No Yes Ou
17. all Back Mode This section is used to decide how the unit will react in the event there is no GSM coverage GPRS gt SMS In the event of GPRS communication is lost the unit will automatically switch to SMS mode While GPRS becomes reacquired the unit will automatically switch back to GPRS mode of operation Note 1 If user is operating his device exclusively in SMS mode he may skip this step 2 In the event that GPRS fails and SMS Fall Back Mode has been set unit will immediately try its SMS connectivity If there is no SMS connectivity the unit will keep switching between SMS and GPRS until the unit synchronizes with one of these 2 modes It is noted that GPRS takes priority if both SMS and GPRS connection exist c SETUP gt Network F LocationNow Suite p LAPAC TECH LAIPAC TECHNOLOGY INC FILE StarFinder Configuration Utility SETUP SYSTEM 1 0 APPLICATIONS epc tmobile com GPRS APN User Name GPRS APN Password SERVER Domain Name 1a laipqw 1 com Port la 1688 state IP 1 i Port 1 0 ALTERNATIVE SERVER i Name 2a Port 2a 0 Static IP 2 0 0 0 0 H Port 2 0 DNS SERVERS DNS IP 1 DNS IP 2 Fig 3 4 2 c Wireless Carrier This section covers the information required by the unit to access your carrier s Access Point GPRS APN The Access Point Name is used by your SIM card to connect to the GPRS network T
18. and call in answer button Note For features with option please check with Laipac Technology Inc to know about their detail 2012 2021 by Laipac Technology Inc All Rights Reserved Page 7 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 3 INITIAL SETUP This section will help you setup and configure your Starfinder Lite GPS tracking device 3 1 What you will need To begin your evaluation you will need the following e Starfinder Lite e Power and I O harness cables complete with Voice and Panic buttons e GSM patch antenna 3 meters cable length e GPS magnet mount antenna 5 meters cable length e GPRS data enabled SIM card with known APN settings 2G and TDMA compliant e Your Identity Leaflet provided in the Evaluation Kit e 9 36V DC power supply e USB A to USB Mini B cable e PC with Windows XP or later Microsoft Operating System GPRS operation assumed 20 12 2021 by Laipac Technology Inc All Rights Reserved Page 8 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 3 2 Setup Summary The setup summary is an outline of what must be accomplished in order to operate the device Detailed descriptions of these steps will be listed in the next sections 1 SO oe Se Os Oe ae eS _ KW N KF O Find a computer with Microsoft Windows O S and IE 8 supported by Adobe Flash Player 9 0 or above Install the latest version
19. ated to the next vehicle maintenance or oil change job is due The unit of distance must be the same as the Mileage Starting Value The default setting for this value is 1000 km Application gt Park amp Accident K LocationNow Suite Beenie LAIPAC TECHNOLOGY INC AE StarFinder Configuration Utility SETUP SYSTEM APPLICATIONS Speed amp Mileage TOWING ALERT Active Disable wv Default Disable Value lz ACCIDENT ALERT Active Disable v Default Disable a Value std Automatically Call Emergency Disable v Default Disable U Towing Alert The Towing Alert must be enabled before it can be used This feature requests Input 1 to be enabled as ignition When vehicle with the unit shuts down its engine if unit experiences a movement that generates 2G or greater force the unit will send an alert to the remote server This may be in a situation where someone tows a vehicle without consent Trigger Value The G Sensor Trigger Value has a default value of 2Gs and should be kept at a low recommended value to sense movement Accident Alert The accident alert requires enabling before it is used It is designed to sense a high impact hit and send an alert upon receiving it similar to that of a vehicle collision In order to have this alert working properly Input 1 must be enabled as ignition also user should provide requested ignition on off signal on
20. c Technology Inc All Rights Reserved Page 2 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide Additional regulatory conformance Specific details about compliance to the following standards and regulatory bodies may be obtained from Laipac Technology Inc e PCS Type Certification Review Board PTCRB e Based on Cellular Telecommunications and Internet Association CTIA Over the Air OTA performance tests e EN 301 511 EN 300 440 EN 62311 EN 301 489 1 3 7 and 60950 1 testing This device complies with Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement This Class B digital apparatus complies with Canadian ICES 003 2012 2021 by Laipac Technology Inc All Rights Reserved Page 3 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 1 Table of Contents INTROD
21. d dates DST Start Date DST End Date This is a user defined value of when the user starts their daylight savings time This is a user defined value of when the user ends their daylight savings time 2012 2021 by Laipac Technology Inc All Rights Reserved Page 23 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 4 3 Input Output Settings T O gt Input Input setting items allows you to activate and select the functionality related to input Input 1 has options Disable and Ignition Input 2 has options Disable Trigger and Counter lt LocationNow Suite p LAPAC TECH LAIPAC TECHNOLOGY INC FILE StarFinder Configuration Utility SETUP SYSTEM I1 0 APPLICATIONS Output Buttons AnalogI n Com INPUT1 As Ignition v Default Disable Alert E Level when Ignition On Off X INPUT2 As Disable v Default Disable No Input 2 Defined Counter Starting Value Alert when Counter Reaches Trigger setting This option allows you to send an alert when the alert signal condition is met on an Input An alert is generated when the voltage level goes from either a High to a Low or from a Low to a High This setting is user defined Counter setting This option allows the user to implement input 2 as a counter The counting signal can be specified as either a Low to High Low gt High or a High to Low High gt L
22. er defined and can be set in kilometers or miles per Mileage Accumulator Starting Value Mileage Alert hour If the unit travels faster than this value an Over Speed Alert will be sent to the GPRS server This function must be enabled before it can be used Unit is able to accumulate distance based on a user defined Mileage Starting Value and the unit of distance during unit moves Whenever moving distance is increased by 1 km mile the incremented value will be added to the Accumulator s current mileage value The Mileage Start Value is user defined and is recommended to match the odometer reading in the equipped vehicle From there you can specify the unit of distance being kilometers or miles and the mileage value will accumulate from there This alert must be enabled before it can be used This alert will be sent to the remote server whenever another new Mileage Delta value is reached during vehicle running It is used to generate a warning for vehicle maintenance warning or oil change etc is coming due For example if Mileage Start Value is 0 km and Mileage Delta Value is 5000km unit will generate Mileage Alerts when Mileage Accumulator has its reading at 5000 km 2012 2021 by Laipac Technology Inc All Rights Reserved Page 29 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide Mileage Delta Value This value is a user defined distance value It is designed to provide a warning rel
23. f internal Relay when its correspondent output is disabled Relay 1 normally opened Relay 2 normally opened Relay 3 normally opened 2012 2021 by Laipac Technology Inc All Rights Reserved Page 37 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 6 OPERATION The following outlines the various operating and reporting features of the Starfinder Lite 6 1 LED Operation Three LEDs are on the front of the unit They are used to indicate the working status of power supply GPS and GSM The following is a description of their operation LED Off Fast Flashing Slow Flashing Keeping On Power Red External power External power not available available GPS Green GPS Searching for Position GPS fixed GSM Yellow Searching for GSM network GSM network connected 6 2 Position Reporting by Event There are many events which can trigger the Starfinder Lite to send a position report Most of them are outlined below For other possible messages contact sales laipac com to purchase the development protocol The descriptions in italics are options and not standard features e Input 1 Opto 1 e Input 2 Opto 2 e Geo Fence e Over speed e Timed Reporting e Distance Reporting e Accident Alert e Towing Alert 2012 2021 by Laipac Technology Inc All Rights Reserved An electrical current signal exerted on Input 1 port will send a position me
24. he Access Point is the carrier s server through which the traffic becomes converted from GSM to GPRS Internet traffic Check with your SIM Card provider for this item User Name The user name authorises your SIM card to access your carrier s Access Point It could be blank in most of case 2012 2021 by Laipac Technology Inc All Rights Reserved Page 13 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide Password The password authenticates your SIM card to access your carrier s Access Point It could be blank in most of case Server This section governs the destination end point for the GPRS traffic Domain Name la This is the domain name of the remote server For www LocationNow com it will be laipgwl com Port 1a This is the Port used by the remote server with Domain Name la For www LocationNow com it should be 1688 Note As a rule if both Domain Name 1a and Static IP 1a are set unit will try to communicate with remote server through the domain name first IP address second If both Domain Name la and Static IP la are inaccessible for any reason then unit will turn to try its back up server Alternative Server if it exists Unit will try domain name of Alternative Server first IP address second It is suggested that user does not fill in Domain Name la and Domain Name 2a with Static IP address Warning If unit has a Fall Back Mode setting along with Prima
25. i Radiation Omni Polarization Vertical Wave Half Wave Dipole 2012 2021 by Laipac Technology Inc All Rights Reserved Page 33 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 5 2 Installation The difficulty level of installing your Starfinder Lite depends on which features you would like to use Outlined here will be the basic installation requirements for real time tracking You can refer to the Optically Isolated Inputs Outputs with relays and Analog Port sections for more advanced hardware features which may require a more intricate installation 5 2 1 Required Hardware e Starfinder Lite e Power I O harness and call button cables e GSM patch antenna 3 meters long e GPS magnet mount antenna 5 meters long e GPRS enabled SIM card with known APN settings 5 2 2 Installing your Starfinder Lite To begin the installation insert your activated SIM card into the SIM card tray Connect the GSM patch antenna long and skinny and GPS magnet antenna square to the appropriate connectors To power the unit connect the power wiring harness and connect the red and black wires to a 9 36V DC supply Make sure the supplied fuse is in place 5 2 3 Considerations There are a few considerations you should make when installing your Starfinder Lite You should make sure the unit is somewhat accessible so that you can connect the unit to a laptop via USB for configuration and local NME
26. ice will send out alert report to server I O gt Com RS232 COM PORT Reserved by Laipac and not opened to customer yet F LocationNow Suite p LAPAC TECH LAIPAC TECHNOLOGY INC FILE StarFinder Configuration Utility m SETUP SYSTEM APPLICATIONS Input Output Buttons Analog In RS232 COM PORT Active Disable v Default Disable Interface with 2012 2021 by Laipac Technology Inc All Rights Reserved Page 28 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 4 4 Application Settings Application gt Speed amp Mileage LocationNow Suite r LAIPAC TECH FILE LAIPAC TECHNOLOGY INC StarFinder Configuration Utility SETUP SYSTEM I 0 APPLICATIONS Parking amp Accident SPEED LIMIT Over Speed Alert Enable v Default Disable Speed Limit 120 H km h v Default 120 km h MILEAGE ACCUMULATOR Active Enable v Default Disable Mileage Starting Value oH km v Default 0 km Mileage Alert Enable v Default Disable iege Deta vaise 5000 km v Default 1000 km M H ecu K __ d Over Speed Alert In order to use this function it must be enabled first The Over Speed Alert formerly known as over speed is designed to send an alert if the unit moves faster then the specified speed limit value Speed Limit The speed limit is us
27. integration 2012 2021 by Laipac Technology Inc All Rights Reserved Page 6 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 2 FEATURES Worldwide GSM GPRS Quad band 850 900 1800 1900MHz Multi mode ready for SMS only GPRS only or SMS GPRS High Sensitivity GPS Receiver of 20 Ch GPS Accuracy 3 5 m Dimension 9 7 x 5 9 x 2 6 cm Built in jacks for SPK and MIC Panic button and Dial button ready Supply voltage range 9 to 36VDC Internal Li lon backup battery able to provide approximately 10h life from a full charge Low operating power consumption less than 1W after battery is charged Both configuration utility and unit are able to have accessing control option Operation Temperature 30C to 65C USB Port for configuration Compatible with Mobile Data Terminal 2 Optically Isolated digital inputs 3 Outputs with relays 1 Analog input available Multiple Geo Fence capability with in out fence alert Data logger capability built in with 2500 positions memory to record time stamp speed location and event state 3 Axial motion G Sensor to report impact accident crash or towing event Real time dynamic position report based on time interval or distance traveled Mileage report and over speed alert Assistance and Emergency call numbers with fail over capability Power saving options available option WAAS EGNOS optional 3 7V 900mAh internal backup battery External panic button
28. n a SETUP gt Device Info B LocationNow Suite p LAPAC TECH FILE StarFinder Configuration Utility peA SETUP SYSTEM 1 0 APPLICATIONS 12020800 357322041165678 160 KB 1 00 10001002 Default 99999999 00000000 Default 00000000 850 1900 x Disable v Default Disable Fig 3 4 2 a Device ID Specific unit identifier that identifies your device for online tracking You can locate the Device ID on your Identity Leaflet or more accurately in your user account on the website www LocationNow com Password Used to protect the StarFinder Lite from other people affecting its operation with SMS commands You can locate the Password on your Identity Leaflet GSM Band This is for setting a frequency that your GSM provider network operates at The North American network bands are 850 1900 and the European network bands are 900 1800 If user is not sure what frequency his carrier operates at please contact them for the correct setting 2012 2021 by Laipac Technology Inc All Rights Reserved Page 11 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide SIM PIN Number If your SIM card is password protected enable this option and input the PIN code The PIN code tells the Starfinder Lite to use the user defined PIN code when communicating with GSM b SETUP gt Services r LocationNow Suite p LAPAC TECH
29. ngine Specifications Value Units Channels 20 Channels RF Frequency 1575 42 MHz Position update rate 1 Hz Active antenna bias voltage 3 V Position accuracy lt 10 Meters Velocity accuracy 0 1 m s Time accuracy 1 us Cold start acquisition time 42 Seconds Warm start acquisition time 38 Seconds Hot start acquisition time 1 Seconds Maximum velocity tracked 515 m s Maximum altitude tracked 18 000 Meters Jerk 20 m s7 Tracking Sensitivity 159 dBm Navigation Sensitivity 159 dBm 5 1 2 GSM Modem Specifications e Quad band GSM GPRS component 850 900 1800 1900 MHz e Designed for M2M and automotive applications e Class 4 2W 850 900 MHz e Class 1 1W 1800 1900 MHz e R amp TTE GCF FCC PTCRB IC e Embedded TCP IP stack e GPRS Class 10 2012 2021 by Laipac Technology Inc All Rights Reserved Page 32 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 5 1 3 GPS Antenna Specifications Frequency 1575 42 3 MHz VSWR 2 0 Max Bandwidth 10 MHz Min Axial Ratio 3dB Typical Impedance 50 Ohm Peak Gain 4 dBic Min Gain Coverage gt 4dBic at 90 lt 0 lt 90 over 75 volume Polarization RHCP DC Voltage 3 3V 5 1 4 GSM Antenna Specifications Bands 850 900 1800 1900 MHz Frequency Range 824 960 MHz 1710 1990 MHz Impedance 50 Ohm VSWR lt 2 0 Gain 2dB
30. ocol from Laipac b As typical vehicle application examples with proper external relays user may use Output3 to control door open Output2 for ignition on off control and Output for driving a horn c Depending on actual application request the output control may have different mode user should check SF Lite Application Firmware Release Note to know about what kind of output control mode is being used by the application firmware he selects I O gt Buttons K LocationNow Suite a LAIPAC i Becente LAIPAC TECHNOLOGY INC FILE StarFinder Configuration Utility _ ____ __ SETUP SYSTEM 1 0 APPLICATIONS Input Output Analogin Com PANIC BUTTON Akies v Default Enable CALL BUTTON Active Default Enable ick Up Incoming Call only no Fast Dia Panic Button Allows user to activate the functionality of the panic button by enabling it Once enabled after pressing panic button unit will initiate the actions below sequentially e Send a panic alert message through GPRS connection to the remote server e Send a SMS message to the SMS device with Emergency No 1 o Initiate a phone call by dialing Assistance Number 2012 2021 by Laipac Technology Inc All Rights Reserved Page 26 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide Call Button Allows you to activate the functionality of the call button by enabling it Once enabled it will allow the user
31. of utility software Complete pre installation of USB driver on computer Power on Starfinder Lite with DC power supply 12V Connect the Starfinder Lite to the computer and reset the unit with reset button Install USB driver on computer Run utility and reset unit with reset button If unit is not activated locked activate unlock it If the existing firmware does not meet the request of utility update firmware Configure the unit and save the settings to unit Disconnect Starfinder Lite with computer Connect the GPS and GSM antennas Insert the valid SIM card into the SIM Card Tray on the front of the unit Press reset button to valid the configuration and make the device start working 2012 2021 by Laipac Technology Inc All Rights Reserved Page 9 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 3 3 Installing the Starfinder Lite Software 3 3 1 Introduction to utility software LocationNow Suite is a stand alone utility software package for all of the major GPS tracking products from Laipac Technology Inc User can use the web link below to download its latest version such as LocationNow Suite 20131009 http www laipac com sflite201update htm Mainly LocationNow Suite is able to provide the two functions below e Configuration e Firmware Update The computer used for installing this utility should be with e Microsoft Windows 7 O S recommended o E8 9
32. ow voltage level change The maximum counting speed is 50 times per second with minimum voltage change of last at least 10 ms Counter Start Value This option allows the device to record how many times the alert gets triggered and accumulates from the value you set it to Counter Alert Value This option allows you to tell the Starfinder Lite to send an alert when the counter value reaches a user defined value If you set it to 90 it will send an alert once the counter s value reaches 90 2012 2021 by Laipac Technology Inc All Rights Reserved Page 24 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide Note Input 1 has been reserved for detecting the trigger signal corresponding to vehicle s ignition on off status Input 1 needs to be enabled if either Accident alert or Towering alert functions to be available The trigger signal exerted on Input should meet the following requests 1 Before starting engine its input voltage is Logic Low 2 After starting engine it keeps input voltage is Logic High 3 When engine shuts down its input voltage is back to Logic Low For definition of Logic level as its correspondent electrical characteristics refer to section 5 2 8 T O gt Output Output setting items allow user to activate and select the functionality related to output All three outputs are driven by individual internal relays and are wired as Normally Open For the elec
33. ry Server and Alternative Server when it loses its GPRS connectivity with its remote servers both Primary and Alternative Server unit will initiate its action of Fall Back Mode Refer to introduction to Fall Back Mode ALTERNATIVE SERVER Configuration of the Alternative Server is optional Alternative Server is a backup server and used when the primary server is not unavailable For its configuration parameters Domain Name 2a and Port 2a as well as Static IP 2 and Port 2 please refer to introduction to Server DNS SERVER DNS IP 1 and 2 Allows you to specify DNS servers by using the IP address Since unit s internal GSM module does this already these settings are optional 2012 2021 by Laipac Technology Inc All Rights Reserved Page 14 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide d System gt Report LocationNow Suite LAIPAC Bente LAIPAC TECHNOLOGY INC FILE StarFinder Configuration Utility SETUP SYSTEM 1 0 APPLICATIONS Data Logger PhoneNumbers Server Query Data Time REAL TIME REPORT By Time Interval o hr 5 al min 0 bel sec Default 30 mins Waypoints per Report E Default 1 point By Distance Interval 1 km v efault 20 km GREEN MODE Green Mode Disable v Default Disable Waypoints will not be sent when the speed is lower than 3km h if this function is enable S
34. ssage to the control center with the corresponding event code An electrical current signal exerted on Input 2 will send a position message to the control center with the corresponding event code Once the hardware Geo Fence is set the Starfinder will report back to the control center when the unit has travelled in out the boundary with the corresponding event code When the Starfinder travels above the set speed limit it will report back to the control center with the appropriate event code When the time interval reporting is set the Starfinder will send a position message to the control center after this amount of time When the distance interval is set the Starfinder will send a position message to the control center after it has travelled this set distance When detected that a high acceleration configurable level is achieved the Starfinder Lite will send a report to the SMS base station or control center With the towing alert enabled and the vehicle ignition is off when the unit senses movement an alert message will be sent Page 38 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide e DL Memory Full Data Logger Memory Full alert will cause the unit to send an alert when the internal memory of the unit is full or has reached max capacity e Mileage Alert Mileage alert will cause the unit to send an alert when travel distance reaches the value specified by user When both time and distance inter
35. st 39 Serial Port 39 Function and its configuration method 40 2012 2021 by Laipac Technology Inc All Rights Reserved Page 5 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 1 INTRODUCTION The Starfinder Lite is a robust platform designed for remote vehicle tracking and security It combines both GSM SMS and GPRS Global System for Mobile Communications Short Messaging Service and General Packet Radio Service communications with ultra sensitive GPS technology to provide a rugged yet precise and reliable tracking service The Starfinder Lite can be used to report positions or events in real time as well as log positions for local or remote downloading The Starfinder Lite comes standard with two optical inputs for connecting to alarm systems or other sensors one analog inputs and three output relays for ignition disabling and remote door unlocking A backup battery is also included Each Starfinder Lite can be programmed with a unique device ID and can send data to any static or dynamic IP address or SMS base station Configuration of the unit can be done locally via the Starfinder Lite configuration utility in Windows or over the air via GPRS or SMS We currently offer our web based tracking application www LocationNow com for tracking and fleet management For custom applications we can provide our ADK kit with confidential protocol to software developers for platform
36. t messages 4 1 Setup Setting Refer to section 3 4 2 a toc 4 2 System Setting SYSTEM gt Report r z D LocationNow Suite s LAIPAC EaR LAIPAC TECHNOLOGY INC FILE StarFinder Configuration Utility SETUP SYSTEM I1 0 APPLICATIONS Data Logger Phone Numbers Server Query Data Time By Time Interval 0 te hr 5 eal min oj sec Default 30 mins Waypoints per Report 1 a Default 1 point By Distance Interval k Ea km wv Default 20 km Green Mode Disable v Oefault Disable Waypoints will not be sent when the speed is lower than 3km h if this function is enable SMART LOG Smart Log Report Report and its setting This option allows you to specify how frequent the unit will send a position update You can specify the report by time value in hours minutes and seconds You can specify the report by distance value in kilometers miles or yards Waypoints per Report This is a user defined value used for report bursting and is governed by report by time An example is if the number of waypoints per report is set to 5 and the report by time interval is set to 1 minute in 5 minutes the receiving server will receive 5 waypoints Smart Log Report The smart log report option allows the unit to automatically log its position and alert information into internal memory in the event there is no GPRS connectivity When the Starfinder Lite reconnects to GP
37. ter 2 This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment 3 This equipment should be installed and operated with a minimum distance of 20 centimetres between the radiator and your body CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking The CE Mark is a conformity marking consisting of the letters CE The CE Mark applies to products regulated by certain European health safety and environmental protection legislation The CE Mark is obligatory for productions it applies to the manufacture affixes the marking in order to be allowed to sell his product in the European market This product conforms to the essential requirements of the R amp TTE directive 1999 5 EC in order to attain CE Marking A notified body has determined that this device has properly demonstrated that the requirements of the directive have been met and has issued a favorable certificate of expert opinion As such the device will bear the notified body number 0560 after the CE mark The CE Marking is not a quality mark Foremost it refers to the safety rather than to the quality of a product Secondly CE Marking is mandatory for the product it applies to whereas most quality markings are voluntary Marking The product shall bear the CE mark the notified body number s as depicted to the right CE0560 2012 2021 by Laipa
38. to select e Auto Answer the incoming call or e Press this button to pick up the phone call Note For unit with application firmware V1 34 and up automatically both of these 2 buttons have been enabled by unit User can skip this setting T O gt Analog In lt LocationNow Suite LAIPAC Esca LAIPAC TECHNOLOGY INC FILE StarFinder Configuration Utility SETUP SYSTEM APPLICATIONS Active Disable v Default Disable High Level Low Level Analog Input It is designed to detect input voltage which ranging between 0 00 and 3 30 volts The threshold of voltage value can be specified through a pull down list As default it is set as Disable a a SETUP SYSTEM APPLICATIONS Active Disable v Default Disable High Level Disable Low Level Alert High Alert Low Alert High Low e Alert High if input voltage value is higher than High Level setting device will send out a alert report to server to remind of server an Alert High event occurs 2012 2021 by Laipac Technology Inc All Rights Reserved Page 27 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide e Alert Low if input voltage value is lower than Low Level setting device will send out a alert report to server to remind of server an Alert Low event occurs e Alert High Low if input voltage is either higher than High Level or lower than Low Level setting dev
39. tput 2 as No No Yes Horn Control on off No No Yes Timer Control 2 Value No No Yes Output 3 as No No Yes Siren Control on off No No Yes Timer Control 3 Value No No Yes Panic Button Panic Alert with Following Action Enabled Enabled Enabled Call Button Call Function pick up the phone Enabled Enabled Enabled Analog Input No No Yes Alert when Analog Input Reaches No No Yes RS232 COM Port Reserved Reserved Reserved Interface With Reserved Reserved Reserved Speed Limit Alert No No Yes Speed Limit Yes Yes Yes Mileage Accumulator No No Yes Mileage Starting Value Yes Yes Yes Mileage Alert for Maintenance No No Yes Mileage Delta Value No No Yes Towing Alert No No Yes Towing G Sensor Trigger Value No No Yes Accident Alert Yes Yes Yes Accident G Sensor Trigger Value Yes Yes Yes Geo fence Setup Yes Yes No Switch Relay 1 Yes Yes No Switch Relay 2 Yes Yes No 2012 2021 by Laipac Technology Inc All Rights Reserved Page 41 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide Switch Relay 3 Yes Yes No Request Real Time Position Yes Yes No Request Device Data Yes Yes No Request Current Status Yes Yes No Disable G sensor Yes Yes No Disable Geo fence Yes Yes No 2012 2021 by Laipac Technology Inc All Rights Reserved Page 42
40. trical characteristics of the relays please locate the electrical characteristics chart located on page 43 FE LocationNow Suite r LAIPAC TECH FILE StarFinder Configuration Utility LAIPAC TECHNOLOGY INC SETUP SYSTEM 1 0 APPLICATIONS Input Buttons Analog n Com OUTPUT1 As Controller v Default Disable OUTPUT2 As Controller v Default Disable OUTPUT3 As Controller v Default Disable Controller The Controller option is used to enable the functionality of an output Each of the 3 outputs is responsible for a different function The table below outlines those functions which being with firmware V1 34 and up 2012 2021 by Laipac Technology Inc All Rights Reserved Page 25 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide Output Switch Relay Action Action on off Command Type Type times time s time s 3 Timed off gt on off 1 1 Stay as Send switch Relay off off Command 2 Fixed off gt on or on gt off 1 Stay as Stay as Send switch Relay on off on or off commands 1 Timed Off gt on off 12 1 1 Send switch Relay off gt on gt off off command Note a on or off command is sent by remote server to control the behavior of those internal relays For customer who wants to use his own server he needs purchase the prot
41. vals are set they work dynamically together like an OR operation This means that whenever either condition is met it will report For detail above refer to section 4 6 3 Reporting by Request In addition to automatically reporting the position you can manually request the current position or settings The following are some parameters which can be requested e System information such as firmware version and memory size e Current position e Current mileage or speed limit setting e Current Report settings e Current Geo Fence settings e Current log settings e Current input status e Current output status 6 4 Serial Port It is reserved now If user wants to have other external device to interface to this port please check with Laipac Technology Inc 2012 2021 by Laipac Technology Inc All Rights Reserved Page 39 Laipac Technology Inc StarFinder Lite User s Manual amp Reference Guide 6 5 Function and its configuration method This table lists the different functions that the Starfinder Lite offers and outlines where they can be configured in reference to the configuration utility remotely using our protocol or with our LBS www locationnow com platform Feature Location Now Remote Config Utility Device ID No Yes Yes Device Password No Yes Yes GSM Band No No
Download Pdf Manuals
Related Search
Now now.gg nowthatstv nowgoal now portal now you see me 3 now.gg roblox now you see me 2 now foods nowadays now stock nowinstock now hiring now hiring near me nowthatstv login now learning now wifi pass now playing now gg talkie now habersham now xfinity now we are free now insurance now gg free fire