MB-Gateway User Manual
Contents
1. 0 24 0 27 in 6 7 mm Screw Torque 17 Ib in 0 2 Nm Operating Temperature Range 0 to 60 C 32 to 140 F Storage Temperature Range 20 to 70 C 4 to 158 F Humidity 5 to 95 RH non condensing Environmental Air For use in Pollution Degree 2 Environment Vibration MIL STD 810C 514 2 Shock MIL STD 810C 516 2 Weight 0 2 Ibs 0 09 kg 2 2 MB GATEWAY USER M Hardware User Manual Ist Ed Rev C 10 13 Chapter 2 Specifications LED Indicators MB GATEWAY STA C ORR SPDC QUA T0 O Can Hi leno STA The STA or STATUS LED is steady ON when the MB GATEWAY has passed power up diagnostics and is ready for use SPD The SPD or SPEED LED is used to represent the Ethernet speed The LED will be ON when the Ethernet speed is 100Mbps and OFF when the speed is 10Mbps TXD The TXD or TRANSMIT DATA LED flashes to indicate that the MB GATEWAY is sending data through the serial port ERR If the MB GATEWAY s ERR ERROR indicator is ON a critical error has occurred The error may be in the card itself or a network problem may be causing this symptom The ERROR indication can be caused by a faulty ground an electrical spike or other types of electrical disturbances Cycle power to the system to attempt clearing the error The ERROR LED will also flash once per second when a firmware update is in progress If the ERROR LED is flashing randomly then this is in2. MB GATEWAY to 0 0 0 0 2 4 MB GATEWAY USER M Hardware User Manual 1st Ed Rev C 10 13 Chapter 2 Specifications Dimensional Drawing Inches mm ZS 0 88 22 2 2X 0 24 96 2 i 6 2 Hecht zc D x GE zc l MB GATEWAY e STA O OERR M n SPD DI Baud Rate De i r OU3AOS o Feet Se Ld 1 00 Wei 11111711 UU CENTERLINE Ms G DO ave EU nn FOR DIN RAIL 116 3 c Se 0g eat d MOUNTING 4 11 Es 89 0 IS Zeg HO 3 06 104 3 E jew GND Cf 0 45 77 8 i 3 ng 11 5 R 3 Stop Bits H B MB GATEWAY 5 Switeh T MODBUS TCP IP to MODBUS RTU Hp 1 75 ER el uen 6 ResetiPOfg 44 5 e COM 10 36 VDC 7 Reserved SL 3 fess n Chasis 10 36 VDC i L ee i 2 1 35 51 H 84 0 091 4 34 23 0 110 1 4 67 7 ien zd MB GATEWAY USER M Hardware User Manual 1st Ed Rev C 10 13 2 5
3. SPECIFICATIONS In This Chapter Specifications 656 eier ed esee BEEN EIERE EE EE C e e naa 2 2 LED Indicators 9E gg RE RE e 2 3 Dip Switch Information sseeeeee n 2 4 Dimensional Drawing 2 5 Chapter 2 Specifications Specifications Port Specifications RJ 45 Speed 10 100 Mbps Ethernet Protection Built in 1 5 KV magnetic isolation Interface Protocol Supported Modbus TCP IP Server Slave Clients Masters Supported 12 simultaneous Modbus TCP connections Cable Type Autodetects Ethernet cable types MDI MDX Port 6 position terminal strip Phoenix 1863194 provided Supported Signal Lines RS 422 o wire Signals TX TX RX RX GND RS 485 3 wire Signals Data Data GND Supported Baud Rates 300 600 1200 4800 9600 14 4k 19 2k 38 4k 57 6k 115 2k Cannot be set with DIP switches Must be set via web browser configuration Serial Parity Odd Even None Interface Data Bits 8 Stop Bits 1 2 Protocol Supported Modbus RTU Client Master Servers Slaves Supported 128 Termination Permanently installed 120 Q resistor between Data and Data Power Consumption 2W Use Class 2 power supply Use conductors rated 60 75 C 3 position terminal strip Phoenix 1863165 provided Wire Range 16 28 AWG Solid or Stranded Conductor 1 5 mm Wire Strip Length
4. dicating a Modbus RTU error is occurring This could be a timeout or an actual error response LK A The LK A or LINK GOOD ACTIVITY LED flashes to indicate that the card sees data traveling on the Ethernet network If any network device is sending or receiving data the LK A LED will be flashing During heavy communication loads this indicator will be steady ON If the LED is OFF then a problem with the Ethernet connection has been detected RXD The RXD or RECEIVE DATA LED flashes to indicate that the MB GATEWAY is receiving data through the serial port MB GATEWAY USER M Hardware User Manual Ist Ed Rev C 10 13 l 2 3 Chapter 2 Specifications iM M M Dip Switch Information Baud Rate 210 Switch OFF 5833200595 000 7 SW cfg n rn ON 011 14400 odas MB GATEWAY ort Bit MODBUS TCP IP to MODBUSRTU 172 Bits 6 Reset IP Cfg 7 Reserved V INPUT COM 10 36 voc Chasis Software Config 4800 9600 14400 19200 ae pneg LA 115200 None Reserved 1Bit S7 reserved Setting S6 to on will on power cycle set the IP address subnet mask and gateway address in the
Download Pdf Manuals
Related Search