ADAM-5000 Series Manual.book
Contents
1. 30 Error Handling and Diagnostics 37 Error Handling and Diagnostics nn 38 V APAX 5522PE User Manual APAX 5522PE User Manual vi Chapter 1 Overview 1 1 Introduction IEC 61850 3 standards specify a number of hardened characteristics that network products should meet to withstand the potentially electromagnetically harsh substa tion environment such as immunity to electrical surge electrostatic discharges and other phenomena that would cause non hardened devices to fail The APAX 5000PE series modules are IEC 61850 3 compliant and can be used in power amp energy appli cations e g smart substation for good protection features APAX 5522PE provides two serial RS 232 ports and two ethernet ports to commu nicate with other devices Programmers can leverage the communication ability through Modbus RTU master slave and Modbus TCP server client 1 2 System Architecture APAX 5522PE can play as standalone controller It needs to be inserted on the APAX 5002 backplane to get power By assembling with other APAX 5000 1 0 mod ules by backplanes 5522 can communicate with other APAX 5000 I O modules through the backplanes Refer to Section 3 1 for the assembly operation APAX 5522PE supports the redundant function To leverage this functionality two CPU modules controllers with the same control program are installed in one sys tem Af2. mi DCD C RTS1 C 1 dC Tx1 C GNDI C DCD2 C RTS2 C Rx C Tx2 IC GND2 C N A C COM C FGND Pin Assignment Description 1 DCD1 DCD for COM1 2 RTS1 RTS for COMI 3 Rx1 Rx for COM1 4 Tx1 Tx for COM1 5 GND1 Ground for COM1 6 DCD2 DCD for COM2 7 RTS2 RTS for COM2 8 Rx2 Rx for COM2 9 Tx2 Tx for COM2 10 GND2 Ground for COM2 11 N A N A 12 13 COM FGND Frame GND for COM APAX 5522PE User Manual Note Refer to Appendix A for more detailed information about RS 232 E communication 1 3 5 Controller ID Settings APAX 5522PE supports backup function and it has to be configured to the different ID address For ID setting please see below ID Address Settings SW1 ID Address ID 0 ON ID 1 1 3 6 Real Time Clock RTC APAX 5522PE delivers built in real time clock which programmers can use it in their application programs When the power is loss the RTC can still run using the power from battery which has been described in section 1 3 1 7 APAX 5522PE User Manual APAX 5522PE User Manual Chapter 2 Product Specifications 2 1 CPU Modules 2 1 1 APAX 5522PE APAX 5522PE L e 2 MM Control System CPU Scale PXA270 520 MHz Memory Flash 32M bytes SDRAM 64M bytes RAM Battery Backup RAM 256KB file system amp 256K Direct Accesss Operating System Windows CE NET or Lin
3. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord All cautions and warnings on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage Never pour any liquid into an opening This may cause fire or electrical shock Never open the equipment For safety reasons the equipment should be opened only by qualified service personnel If one of the following situations arises get the equipment checked by service personnel The power cord or plug is damaged Liquid has penetrated into the equipment The equipment has been exposed to moisture The equipment does not work well or you cannot get it to work according to the user s manual The equipment has been dropped and damaged The equipment has obvious signs of breakage DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW 20 C 4 F OR ABOVE 60 C 140 F THIS COULD DAMAGE THE EQUIPMENT THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER S INSTRUCTIONS The sound pressure level at the operator s pos
4. User Manual APAX 5522PE IEC 61850 3 Certified PAC with Marvel XScale CPU AD ANTECH eAutomation Copyright The documentation and the software included with this product are copyrighted 2009 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reliable How ever Advantech Co Ltd assumes no responsibility for its use nor for any infringe ments of the rights of third parties which may result from its use Acknowledgements Intel and Pentium are trademarks of Intel Corporation Microsoft Windows and MS DOS are registered trademarks of Microsoft Corp All other product names or trademarks are properties of their respective owners Product Warranty 2 years Advantech warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of pur chase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech or which have been subject to misuse abuse accident or improper
5. APAX 5522PE to the APAX 5002 backplane by pulling down the module locks on two sides 15 APAX 5522PE User Manual V Step 4 Insert another APAX 5000 I O module on the same APAX 5002 backplane Use tongue and groove slots to move the module Step 5 Lock that APAX 5000 I O module to the APAX 5002 backplane by pulling down the module locks on two sides APAX 5522PE User Manual 16 Lock Step 6 If you need more than one APAX 5000 I O module stack another APAX 5002 backplane to the original APAX 5002 backplane Warning When you assembly different backplanes together remember to turn off the power connected to the backplane If not the backplanes may be A damaged Turn on the power again after you complete the assembly for all backplanes 17 APAX 5522PE User Manual Step 7 Lock the stacked APAX 5002 backplane to the original APAX 5002 backplane by the backplane locks on two sides Note Ifyou want to provide more power to the system you can connect 1 2 another power supply wire to the power connections on the second APAX 5002 backplane The wiring procedure is the same as step 1 Step 8 Insert another APAX 5000 I O module on the second APAX 5002 backplane Step 9 Lock that APAX 5000 I O module to the second APAX 5002 backplane by pulling down the module locks similar as step 5 APAX 5522PE User Manual 18 Step 10 If needed repeat step 8 9 to have another APAX 5000 I O module on the second APAX 5
6. C B Installed Input Fuse F 3 15 A 250 V not accessible Output Output Power 72 watts B Power Loss at rated load approximated 8 9 W Residual Ripple 240 mVpp Startup Delay lt 3 second m Rated Voltage 24 Voc Mm Voltage Rise typical 60 ms m Rated Output Current 3 A B Output Current Limitation 3 5 4 3 A W Efficiency gt 87 at 115 230 Vac Input Voltage Rated load Protection Isolation Protection In Out 42 42 Vic W Over Voltage Protection Shutdown at approx 25 27 Vbc latch off mode m Over Load Protection Auto recovery mode WB Short Circuit Protection Auto recovery mode General Certifications CE FCC Class A UL 508 UL cUL approval Energy Star m Enclosure ABS PC W Diagnostics LEDs 1 x Power B Dimensions W x H x D 75x 151 x 115 mm Operating Temperature 10 55 C B Storage Temperature 20 70 C Relative Humidity 5 95 non condensing B Leakage Current lt 3 5 mA APAX 5522PE User Manual 12 Chapter 3 Mechanical Installation 3 1 3 1 1 Mechanical Assembly and Power Connection Standalone Controller with Direct Power Input As introduced in Chapter 1 APAX 5522PE can perform as standalone controller It needs to be inserted on one APAX 5002 backplane module Insert One APAX 5000 O module on the same backplane module That I O module can be controlled by APAX 5522PE If you want to have more APAX 5000 1 0 modules to be controlled simply
7. Sim ilar to Step 3 Step 5 and Step 9 in section 3 1 1 Note the total number of APAX 5000 module is odd you can use the APAX x 5001 as the last backplane All the mounting procedure is similar to APAX 5002 mounting 29 APAX 5522PE User Manual 3 3 2 Wall Panel Mounting Mount the APAX 5522PE module to a wall panel through backplane using two screws per module Use M4 or 8 panhead screws Refer to figure below for the dimensional template 141 5 IT mi Below are the procedures for the wall panel mounting APAX 5522PE User Manual 30 Step 1 Pull down the DIN rail lock at the back of the first APAX 5002 backplane V Unlock Step 2 Hang the APAX 5002 backplane onto the screw on the wall panel The screw for APAX 5002 to hang should be special designed We have provided it in accessory 31 APAX 5522PE User Manual Step 3 Mount the first APAX 5002 backplane to the wall panel using two standard M4 or 8 panhead screws We also provide the two screws in accessory Step 4 Stack Another APAX 5002 backplane to original backplane Lock the back plane together APAX 5522PE User Manual 32 Step 5 Mount that APAX 5002 backplane to the wall panel using two standard M4 or 8 panhead screws Step 6 Repeat Step 4 Step 5 until all necessary APAX 5002 backplane
8. installation Advantech assumes no liability under the terms of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous testing most of our customers never need to use our repair service If an Advantech product is defec tive it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any onscreen messages you get when the problem occurs 2 Call your dealer and describe the problem Please have your manual product and any helpful information readily available 3 If your product is diagnosed as defective obtain an RMA return merchandize authorization number from your dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for warranty service 5 Write the RMA number visibly on the outside of the package
9. mission quality 4 t is suggested to power on APAX 5522PE and all the VO modules together to avoid any unpredictable situation APAX 5522PE User Manual 20 Note For the line topology as shown by figure above the maximum distance E between two backplanes is 100 m And there are maximum 30 APAX A 5002 backplanes used in the system for line topology to remain real time performance Warning For the star topology use unmanaged industrial Ethernet switches such as Advantech EKI 2528 with 100 Mbps transmission speed for expansion DO NOT use management switch hub or router between backplanes The network for the expansion should be a local network NOT to connect with other external network like public network in enter prise network including Internet 21 APAX 5522PE User Manual 3 1 2 Standalone Controller with APAX 5343E as Power Input APAX 5522PE and other APAX 5000 I O modules can also be powered by the APAX 5343E power supply module connected to the left side of the whole system The power can be transferred to APAX 5522PE and other APAX 5000 I O modules though the backplanes Step 1 Follows the procedures described in Section 3 1 1 to assembly APAX 5522PE and other APAX 5000 I O modules into one complete system The only dif ference is that you don t need to connect the power supply wiring to the power con nectors on the backplane step 1 in Section 3 1 1 Step 2 Pull up the module locks on the upper c
10. stacked other APAX 5002 backplanes to the original backplane and inserted APAX 5000 1 0 modules on the stacked backplanes It becomes one complete sys tem and APAX 5522PE can communicate with these APAX 5000 I O modules through the backplanes Note If use APAX 5002L backplane it doesn t support external power source i connections and Local Bus IO extension functions There are two ways that APAX 5522PE can be powered when it performs as a stand alone controller One way is to connect the DC power supply wire directly to the power connector on the backplane Another way is using Advantech APAX 5343E power supply module refer to Section 3 1 2 for more detail When you wire the power supply to the backplane the power is transferred between backplanes and provides to APAX 5522PE and other APAX 5000 I O modules inserted on the backplanes Refer to figures below for how to wiring the power to the backplane and how to assembly APAX 5522PE and other 5000 I O modules with backplanes Step 1 Connect the power supply wire to the power connectors on the 2 slot APAX 5002 backplane module APAX 5522PE User Manual 14 Warning If you use APAX 5000 digital modules in the same system use different power supplies for the system and the the digital channels on digital A modules to have isolation protection between digital channels and sys tem Step 2 Insert APAX 5522PE on the APAX 5002 backplane module V Step 3 Lock
11. 002 backplane If you need more APAX 5000 I O module repeat Step 6 Step 10 until all necessary APAX 5000 1 0 modules are inserted on the backplanes When the total number of APAX 5522PE and APAX 5000 I O modules is odd you can use 1 slot APAX 5001 backplane module as the last backplane in the system 19 APAX 5522PE User Manual Lock There is an expansion port on front side of APAX 5002 With this port users can build a remote expansion architecture remaining fast local bus data transmission speed Standard Ethernet cables can be used to connect any two APAX 5002 However shielded industrial Ethernet cable MUST be used instead of standard Ethernet cable when the system is used in harsh environment such as factory automation Unman aged industrial Ethernet switches such as Advantech EKI 2528 with 100 Mbps transmission speed can also be used between two APAX 5002 Therefore you can flexibly build any remote expansion with line tree or star topology All the APAX 5000 YO modules can benefit from the remote expansion architecture with local bus speed Refer to figure below for the expansion topology Warning 1 DO NOT use managed switch hub or router between backplanes for expansion A 2 The network for the expansion should be a local network NOT to con nect with other external network such as public network in enterprise network including Internet 3 Cat 6 Ethernet cable is strongly recommended for better data trans
12. and ship it prepaid to your dealer Part No XXXXXXXXXX Edition 1 Printed in Taiwan October 2012 APAX 5522PE User Manual ii Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring We recommend the use of shielded cables This kind of cable is available from Advantech Please contact your local supplier for ordering information FCC Class A Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Opera tion of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Technical Support and Assistance 1 Visit the Advantech web site at www advantech com support where you can find the latest information about the product 2 Contact your distributor sales representative or Advantech s customer service center for technical support if you need additional assistance Please have the following information ready befor
13. are screwed on the wall panel Note When the total number of APAX 5522PE and APAX 5000 VO modules x is odd you can use APAX 5001 1 slot backplane as the last backplane in the system The procedure to screw APAX 5001 on the wall panel is similar as APAX 5002 33 APAX 5522PE User Manual Step 7 Insert APAX 5522PE and all necessary APAX 5000 I O modules to the back planes Similar to Step 2 Step 4 and Step 8 in section 8 1 1 Step 8 Lock APAX 5522PE and all necessary APAX 5000 I O module to the back plane by pull down the buckle Similar to Step 3 Step 5 and Step 9 in section 3 1 1 Warning APAX 5522PE will generate a significant heat which is dissipated via a passive ventilation system This system requires the unit to be mounted A correctly In order to have better ventilation no matter DIN rail or wall mounting is adopt remember to locate APAX 5522PE at the first slot on the first backplane Besides APAX 5522PE and all APAX 5000 VO modules should be placed vertically Refer to figure below mo nm y 0 Toni RR Toward Ad ground II E E YESH IL APAX 5522PE User Manual 34 We suggest remaining enough clearance space from enclosure walls and adjacent equipments No closer than 50 mm 2 in apart on all sides as shown below This provide ventilation and makes assembly more easily IA ERRORI 000000 ns 0000000 EEE 5 RER RER 50
14. ase of one APAX 5343E Then you can separate the upper case of APAX 5343E from its backplane APAX 5522PE User Manual 22 Step 3 Stack the backplane of APAX 5343E to the left side of the first APAX 5002 backplane in the system Step 4 Lock the stacked APAX 5343E backplane to the APAX 5002 backplane by the backplane locks on the APAX 5002 backplane 23 APAX 5522PE User Manual Step 5 Insert the upper case of APAX 5343E back on its backplane Use tongue and groove slots to move the upper case APAX 5522PE User Manual 24 Step 6 Lock the upper case of APAX 5343E to its backplane by pulling down the module locks on the upper case Connect AC power code to the power connectors on the upper case of APAX 5343E Then the whole system is powered on 25 APAX 5522PE User Manual 3 2 Decommissioning and Disposal APAX 5522PE supports hot swap functionality It means APAX 5522PE can be removed from the backplane or inserted on the backplane when the complete system is power on This helps saving maintenance effort and cost The hot swap functional ity is implemented by the module locks Please follow the procedure below Step 1 Pull up the two module locks on side of APAX 5522PE Unlock GND V APAX 5522PE User Manual 26 Step 2 Detach APAX 5522PE from the backplane V Repeat Steps 1 2 for the APAX 5000 I O modules disassembly The device must be fully dismantled in order to dispose of it Electron
15. e the program is run E ning APAX 5522PE User Manual 38
16. e you call Product name and serial number Description of your peripheral attachments Description of your software OS version application software etc A complete description of the problem The exact wording of any error messages Safety Precaution Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage W avoid electrical shock always disconnect the power from your PC chassis before you work on it Don t touch any components on the CPU card or other cards while the PC is on Disconnect power before making any configuration changes The sudden rush of power as you connect a jumper or install a card may damage sensitive electronic components iii APAX 5522PE User Manual Safety Instructions 10 11 12 13 19 16 17 18 19 20 21 22 23 Read these safety instructions carefully Keep this User Manual for later reference Disconnect this equipment from any AC outlet before cleaning Use a damp cloth Do not use liquid or spray detergents for cleaning For plug in equipment the power outlet socket must be located near the equip ment and must be easily accessible Keep this equipment away from humidity Put this equipment on a reliable surface during installation Dropping it or letting it fall may cause damage The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS
17. how to insert plug CF Note There might be compatibility issues with certain brands of CF card We strongly recommend using an Advantech SQFlash which is tested in the E development stage Contact Advantech support if you have any applica tion enquiries Ethernet Port The APAX 5522PE is equipped with one Ethernet port which is fully compliant with IEEE 802 3u 10 100Mbpst The Ethernet port provides a standard RJ 45 with upper left LED indicator on the front side showing Link Activity Off Not Link Green and Flash Link and Activity and lower left LED indicator showing LAN speed Orange 100 Mbps Off 10 Mbps Refer to figure below for Ethernet port pin assignment L Pin Assignment Description 1 TD Transmit 2 TD Transmit 3 RD Receive 4 N C not used 5 N C not used 6 RD Receive 7 N C not used 8 N C not used Note The Ethernet port is only used in LAN not for connection to telecommu x nication circuits 5 APAX 5522PE User Manual 1 3 4 RS 232 Communication Ability APAX 5522PE delivers two isolated RS 232 serial communication interface ports to connect with other devices APAX 5522PE RS 232 interface supports auto data flow control functionality it automatically detects the direction of incoming data and switches its transmission direction accordingly l
18. ic parts must be disposed of in accordance with national electronics scrap regulations 27 APAX 5522PE User Manual 3 3 Mounting 3 3 1 DIN rail Mounting APAX 5522PE module can be mounted through backplane to the following DIN rails 35 x 7 5 mm or 35 x 15 mm Below are the procedures for the DIN rail mounting Step 1 Pull down the DIN rail lock at the back of APAX 5002 backplane Unlock Step 2 Attach the APAX 5002 backplane on the DIN rail Unlock Step 3 Repeat Step 1 Step 2 until necessary APAX 5002 backplanes are all attached on the DIN rail APAX 5522PE User Manual 28 Note When the total number of APAX 5522PE and APAX 5000 VO modules is odd you can use APAX 5001 1 slot backplane as the last backplane EI in the system And the procedure to attach APAX 5001 on the DIN rail is similar as APAX 5002 Step 4 Move all backplanes to stack them together Then slide the backplane locks on the backplanes to fasten all backplanes Similar to Step 6 and Step 7 in section 3 1 1 Step 5 Slide the DIN rail lock of all backplanes into the position to fix all backplanes to the DIN rail Lock i Step 6 Insert the APAX 5522PE module and all necessary APAX 5000 I O modules to the backplanes Similar to Step 2 Step 4 and Step 8 in section 3 1 1 Step 7 Slide the module lock of the APAX 5522PE module and all necessary APAX 5000 I O modules into the position to fix these modules to related backplanes
19. ition according to IEC 704 1 1982 is no more than 70 dB A DISCLAIMER This set of instructions is given according to IEC 704 1 Advantech disclaims all responsibility for the accuracy of any statements contained herein APAX 5522PE User Manual iv Chapter Chapter Chapter Chapter 1 La D 2 2 1 2 2 3 1 3 2 3 3 4 1 Overvievv 1 INTOQUCTION eer 2 System Architecture init 2 gf ee Rauf 4 1 3 1 Battery Backup RAM 4 1 3 2 CF Slot for Data Storage 5 1 39 Ethernet Porti ee ee 5 1 3 4 RS 232 Communication Ability 6 1 8 5 Controller ID Settings 7 1 3 6 Real Time Clock RTC 7 Product Specifications 9 CPU Modules eene enne nnne nennen 10 23 APAX bB22PE ned anal 10 2 1 2 APAX 5522PE Dimensions 11 Power Supply Modules 12 2 24 iss idee dedu ente id mener 12 Mechanical Installation 13 Mechanical Assembly and Power Connection en 14 3 1 1 Standalone Controller with Direct Power Input 14 3 1 2 Standalone Controller with APAX 5343E as Power Input 22 Decommissioning and 6 26 MOUNTING rss ii 28 3 3 1 DIN rail MOUNTING m 28 3 3 2 Wall Panel
20. mm Top pod 550 aaa Rana B BR BR Kl a innen K r RELA RER Kl k KR Feel RES EER ER Kl Feel ps Ba Ban E Se 22 Se e 22 2 H SR Resa Ks Feel IHR Kl Es Se 2 ss 2 amp Toward BEER RR FRERES ZA RE 505050508 HR RR KR Res RR A G rou nd K p ES Reza e APAX 5620 Controller APAX 5620 Controller APAX 5000 1 0 Module APAX 5000 1 0 Module APAX 5000 1 0 Module APAX 5000 1 0 Module 50mm Bottom RE T Ote ttem Mati tendat aet dear 4 d H a RER EEE TER Ba RRENEN e peso 35 APAX 5522PE User Manual APAX 5522PE User Manual 36 Error Handling and Diagnostics 4 1 Error Handling and Diagnostics There are four LED for diagnostics on the front panel of APAX 5522PE Below are the meanings for the 4 LEDs PWR When the APAX 5522PE is powered this LED will be lit Green RUN Programmer can use software to define when this LED is lit Green ERR Programmer can use software to define when this LED is lit Orange BAT When the battery is out of power this LED will be lit Orange Once this LED is lit you need to change the battery Refer to Section 1 3 1 for how to change the battery Note For APAX 5522PEKW If you download KW program to it and select to E run the program the RUN LED will flash to notic
21. ter both controllers are enabled to have backup function the APAX 5000 sys tem will automatically delegate one of the two controllers as the master controller The master controller will run the control program to execute the control process while another controller the backup controller is put on standby The master control ler will periodically send living message to the backup controller If the backup con troller dose not receive living message from master controller it will automatically become master controller and take the control responsibility and restarts the control process execution The maximum operation time for the backup controller to become master controller Changing master controller means there is something wrong for the previous master controller Therefore engineers can check or change the previous master controller with a new one and enable it to have redundant functionality becoming a second APAX 5522PE User Manual 2 backup controller Then if the new master controller fails again the second backup controller will automatically take the control responsibility This mechanism ensures the control system will continuously run the control pro cess And the system won t be stopped even if controller fails 3 APAX 5522PE User Manual 1 3 Features 1 3 1 Battery Backup RAM APAX 5522PE provides 512 KB battery backup RAM 256KB File System 256KB Direct Access for saving important data This ensures that yo
22. u have a safe place to store critical data You can now write software applications without being concerned that system crashes will erase critical data from the memory If there is no power pro vided to APAX 5522PE the battery life can be 2 years There is a BAT LED in the front panel of the APAX 5522PE and it will be lit when the battery is out of power Once the BAT LED is lit please change the battery Refer to figure below for the loca tion of the battery and how to change the battery Below is an example image of the APAX 5520 Note After you remove the battery the data can remain 30 minutes Battery Specifications W Battery Type CR2032 Electrical Properties Nominal voltage 3 0 V Nominal capacity 225 mAh Dimension Diameter 20 0 mm Height 3 2 mm Weight 3 1 g Warning Battery may explode if mistreated Do not recharge disassemble or dis N pose of in fire APAX 5522PE User Manual 4 1 3 2 1 3 3 CF Slot for Data Storage APAX 5522PE has built in Microsoft Windows CE NET and Linux operating systems The operating system is installed in the flash Your application program will also be stored on the flash However we strongly suggest not saving data to the flash Repeat reading and writing will serious damage the flash life APAX 5522PE delivers an internal CF slot for data storage It only supports FAT and the CF card size can be up to 1 GB Refer to figure below for the location of CF slot and
23. ux Real time Clock Yes Watchdog Timer Yes Control Software VS Net Library automationX aX5 runtime Storage 1 x Type Il CompactFlash card slot Communication Ethernet WB LAN 2 x RJ 45 Port 10 100 Mbps W Protocol Modbus TCP Server and Client plus IEC60870 5 101 103 104 Communication Serial iz nn rs 2 x Isol RS 232 Environment W Operating Temperature 20 70 C m Storage Temperature 40 85 C W Relative Humidity 5 95 non condensing Note Refer to Chapter 4 for LED diagnostics B APAX 5522PE User Manual 10 2 1 2 APAX 5522PE Dimensions APAX 5522PE Fa L f Dept Tx1 amp od run D RTS2 ER 3 Ra N A oo oo an LT LAN1 LAN2 11 Right Front 84 00 i CD C D E CJ JCD JLD JC D e CD CD Sm CD CD d 9 IJ 1 dh rm m 57 30 Bottom 11 APAX 5522PE User Manual 2 2 Power Supply Modules 2 2 1 APAX 5343E Input Rated Voltage 115 230 Vac W Voltage Range 90 264 Vac Input Current 1 5 A at rated load B Input Frequency Range 47 63 Hz W Inrush Current 50 A one cycle at 25
Download Pdf Manuals
Related Search