Owner`s Manual
Contents
1. IMPORTER Comercializadora Thomson de M xico S A de C V Alvaro Obregon No 151 Piso 13 Col Roma Delegaci n Cuauht moc C P 06700 M xico D F Telefono 52 55 11 020360 RFC CTM 980723 KS5 Main plug is used as the disconnect device it shall remain readily operable and should not be obstructed during intended used To be completely disconnected the apparatus from supply mains the main plug of the apparatus shall be disconnected from the mains socket outlet completely The descriptions and characteristics in this owner s manual are for the purpose of general reference only and not as a guarantee In order to provide you with the highest quality product we may make changes or modifications without prior notice The English version serves as the final reference on all product and operational details should any discrepancies arise in other languages Before You Plug for Power 1 Setting Time Zone You may slide the TIME ZONE selector at the back of the unit to Eastern EST Central CST Mountain MST or Pacific PST refer to the maps on the right 2 Daylight Saving You can slide the DST switch at the back of the unit to turn on off in areas observing not observing such time change WARNING Please avoid playing with these buttons after entering the Clock Alarm set mode Auto Clock Set You do not have to set the clock time as a built in automatic time set system is equipped in this clock powered by2. limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you e This warranty gives you specific legal rights and you also may have other rights that vary from state to state If you purchased your product outside the USA This warranty does not apply Contact your dealer for warranty information iE
3. step 2 again If synchronization still fails after several attempts and the temperature display on the main unit stops scrolling and starts to flash you have to perform both steps 1 and 2 again Battery Back Up Operation This clock radio is equipped with a memory holding system that can be powered with 2 AA batteries included and installed The power failure protection circuit will not operate unless battery is installed When normal household power is interrupted or AC line cord is unplugged the batteries will power the clock radio to keep track of time and alarm settings programmed into memory When the battery backup functions the digital display will not light however the function of alarm still occurs during the power interruption if remaining battery power is adequate Normal operation will resume after AC power is restored so you will not have to reset the time or the alarm Replace batteries as follow 1 Remove battery compartment door located at the bottom of the radio by applying thumb pressure to the tab on battery door and then lift the door out and off the cabinet 2 Insert 2 AA batteries 3 Replace the compartment door Note we recommend that you replace the batteries every 2 3 years Selecting Radio Mode Press RADIO AUX to switch on radio Switching Band Slide the AM FM switch on the back of the unit to select AM or FM band Tuning the Radio Turn the TUNING kno
4. 3V 2 X AA batteries included and installed All you have to do is to plug this clock for power and current time will be shown automatically However the batteries can also be exhausted and we recommend that you replace the batteries every 2 3 years In case the memory holding batteries are accidentally removed you may set the clock manually with following procedures Setting Clock 1 Slide the switch o AWAKE1 WAKE2 on the top of the unit to clock position This function wakes you up after a short period of time from 10 minutes to 2 hours 1 Press NAP on the top of the unit and use lt lt REV or FWD gt gt to set the duration up to 2 hours each press decreases or increases duration by 10 minutes 2 The clock time shows after a few seconds if no button is pressed NAP icon shows on the display to indicate the function is activated 3 To check remaining nap time press NAP once to show the time on the display briefly 2 Press lt 4 REV or FWD gt gt to set the clock time The time decrements or increments will follow by a faster rate when you press and hold the buttons The between hour and minute time flashes when you are setting the time AM or PM icon will also beside the time 3 Slide the switch o WAKE1 WAKE2 on the top of the unit to o position when finished Clock Projector A clock projector is located on the left side of the unit Clock time can be projected onto ceili
5. ERVICE PERSONNEL SEE MARKING ON BOTTOM BACK OF PRODUCT WARNING TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE Top View OFF turns the unit off FWD gt gt sets time increases value SNOOZE PROJECTION enters snooze mode where the alarm will quiet but sound again once the snooze period is over turns on the projector for about 10 seconds when it is switched off lt 44 REV sets time decreases value RADIO AUX turns unit on selects radio or AUX mode WAKE OFF activates deactivates and sets wake function om WAKE1 WAKEZ2 slide switch to lock setting and to set Wake 1 Wake 2 and clock time NAP activates NAP function SLEEP activates sleep function Back View AUTO DIMMER turns auto dimmer function on or off TIME ZONE slide to select time zone corresponds to your location DST turns daylight saving function on or off AMIFM selects between AM and FM bands PROJECTOR ON OFF turns projector on or off ANGLE rotates the projected image Side View VOLUME adjusts volume TUNING selects radio frequencies AUX IN AUX input jack ID performs temperature information synchronization with the digital thermometer C F selects temperature scale Switching Off Wake Function Press WAKE J OFF 1 or 2 repeatedly on the top of the unit until no wake mode icon shows on the display Me Note SmartSnooze is
6. FCC Information This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation In accordance with FCC requirements changes or modifications not expressly approved by Thomson Inc could void the user s authority to operate this product This device generates and uses radio frequency RF energy and if not installed and used properly this equipment may cause interference to radio and television reception If this equipment does cause interference to radio or television reception which you can determine by unplugging the unit try to correct the interference by one or more of the following measures e Re orient the receiving antenna that is the antenna for the radio or television that is receiving the interference e Move the unit away from the equipment that is receiving interference e Plug the unit into a different wall outlet so that the unit and the equipment receiving interference are on different branch circuits If these measures do not eliminate the interference please consult your dealer or an experienced radio television technician for additional suggestions Also the Federal Communications Commission has prepared a helpful booklet How To Identify and Resolve Radio TV Interference Problems Th
7. ansmit temperature information to the main unit and shows at the lower right of the display indicated by OUT Install 2 AAA batteries not included in the thermometer 1 Unscrew at the battery compartment to open the door 2 Install two AAA batteries by referring to the indications in the compartment 3 Replace the battery compartment door of the thermometer and secure closing with the screw Once the main unit clock radio is plugged for power it can automatically synchronize with the digital thermometer with batteries installed to show the temperature You do not need to do anything Mountain MST Central CST Eastem EST However if you find abnormal temperature display on the main unit you may synchronize the temperature manually by following the steps below 1 At the main unit clock radio press and hold ID until the temperature display at the lower right of the display starts scrolling 2 At the digital thermometer Unscrew at the battery compartment to open the door Press and hold ID inside the battery compartment until the antenna icon on the display of the thermometer flashes Synchronization starts automatically and should be finished within several seconds When synchronization succeeds the antenna icon stops flashing and the synchronized temperature shows on the main unit 3 If synchronization fails no temperature shows on the main unit perform
8. b on the right of the unit to adjust radio frequency Radio frequency shows on the display FM Antenna The power cord acts as your FM antenna The power cord picks moderate to strong stations and eliminates the need for an external antenna in most strong signal areas Be sure the power cord is stretched out to its full length Changing position of the power cord may improve reception Built In AFC The Built In Automatic Frequency Control AFC works only on FM It helps reducing drift on FM reception and keeping the Clock time and radio frequency are display on the display area at the front of the unit The display brightness can be adjusted automatically by analyzing the intensity of surrounding light sources Line Out Temperature Sensor If you are going to install the thermometer outdoor with extreme temperatures below 14 F 10 C the use of line out temperature sensor included is recommended to avoid battery failure Insert the sensor connector to the receptor below ID button in the battery compartment The sensor wire should be extended from battery compartment through the hole at the lower left of the door Back view with battery compartment door removed batteries not included Battery door screw hole CI F selects temperature scale shows on the display ID performs temperature information synchronization with the main unit Receptor for connecting the line out temperature sensor include
9. d My Note X SE Power is fed to the unit even when it is not functioning To cut the power supply off the power cable must be unplugged Power Failure Indicator When AC power is interrupted disconnected for a short period of time both time and alarm settings will change unless batteries are installed After AC power is restored reconnected the Digital Display will blink to indicate that power was interrupted and you should readjust the time and alarm settings radio locked in on the FM station to which it is tuned When tuning in FM stations you may notice that the station you are tuning can be well tuned on two or three nearby points on the dial Always tune carefully at the loudest and clearest point AM Antenna A built in ferrite rod antenna eliminates the need for an outside antenna for AM reception Rotating the unit slightly may improve reception of distant AM stations Listening to Auxiliary Source 1 Connect your auxiliary source e g mp3 player to the AUX input jack on the right side of the unit 2 Turn on the unit and your auxiliary source 3 Press RADIO AUX to switch to listen to auxiliary source The AUX indicator on the front display will turn on Press again to switch back to listen to the radio Slide AUTO DIMMER on the back of the unit to ON position to activate the function Placing thermometer The digital thermometer can be fixed on walls with the included holder screws
10. h off the Wake function see Switching off Wake Function Tip The unit equips with GRAD Rog U WAKE feature the alarm tone volume will increase gradually to its maximum in about 30 to 45 seconds incorporated into other products e Products purchased or serviced outside the USA e Acts of nature such as but not limited to lightning damage Limitation of Warranty THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED NO VERBAL OR WRITTEN INFORMATION GIVEN BY THOMSON INC ITS AGENTS OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER THOMSON INC SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE How state law relates to this warranty e Some states do not allow the exclusion nor
11. is booklet is available from the U S Government Printing Office Washington DC 20402 Please specify stock number 004 000 00345 4 when ordering copies FCC ID T4HSW0001 SERRE SD jo SmartSnooze Operation This operation allows extra sleep time after the wake function is on The alarm will be off by pressing SNOOZE NAP SLEEP lt lt REV or FWD gt gt until the snooze period is over Snooze function can be used repeatedly up to 30 minutes default 9 minutes Set the quiet period as follow 1 Press and hold SNOOZE 2 Press lt 4 REV or FWD gt gt to set the quiet period The time decrements or increments will follow by a faster rate when you press and hold the buttons In sleep mode you can set the duration up to 2 hours before the radio turn off automatically 1 Press and hold SLEEP on the top of the unit and use lt lt REV or FWD gt to set the duration up to 2 hours default 59 min The time decrements or increments will follow by a faster rate when you press and hold the buttons Note The radio will be switched on fo7 U hale x RISK OF ELECTRIC SHOCK DO NOT OPEN THE LIGHTNING CAUTION TO REDUCE THE THE EXCLAMATION FLASH AND ARROW RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS IN SIDE REFER SERVICING TO QUALIFIED S
12. ngs or walls for easy reference The distance between the projector and the projected surface should be within 2 6 to 9 feet 0 8m to 2 8m The projector can be rotated 90 forward or backward Slide the PROJECTOR switch to turn on or off the projector To rotate the projected image press ANGLE repeatedly Each press will rotate the image by 90 The clock time can also be displayed temporarily from the projector even if it is switched off Press SNOOZE PROJECTION once to display the clock time for about 10 seconds When the alarm sounds press OFF to switch it off To cancel the function before the nap time ends press and hold NAP until no NAP icon shows on the display FCC Information EJ Important Information Important Information Before You Begin _ e Make sure that you keep your set away from water and high temperatures Do not use your System immediately after transporting it from a cold place to a warm place as condensation may cause the system to malfunction e Keep your unit away from humid areas and abnormally hot places e To prevent personal injury do not reverse any batteries e The use of apparatus in moderate climates e The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus e No naked flame sources such as lighted candles should be placed on the apparatus e Attention should be drawn t
13. not provided If you are placing it outdoor ensure that it does not get wet by rain and is not under direct sunlight If you are using the line out temperature sensor place the thermometer indoor and extend the sensor wire outside the window M Tips 4 pe M K The thermometer sends the latest temperature information to the main unit every 35 seconds There may be delay on the main unit to show the most updated temperature changes When the outdoor temperature display is flashing on the main unit there may be no signal receiving from the digital thermometer Please make sure the batteries of the thermometer are not empty and the thermometer is not placed too far from the main unit and without obstacles between them Note Both the main unit and K thermometer will show LLL if temperature is lower than 58 F 50 C and will show HHH if it is higher than 140 F 60 C a os T he user manual FM Li Oa a EN E RP5440 It is important to read this instruction book prior to using your new product for the first time Es importante leer este manual antes de usar por vez primera su euipo Setting Wake Time This unit allows two wake times to be set 1 Slide the switch WWAKE1 WAKE2 on the top of the unit to WAKE 1 or WAKE 2 position 2 Press lt lt REV or FWD gt gt to set the respective wake time The time decrements or increments will follow by a faste
14. o the environmental aspects of battery disposal e Minimum distances 2cm around the apparatus for sufficient ventilations e The ventilation should not be impeded by covering the ventilation opening with items such as newspaper table cloths curtains etc e The rating plate is located at the bottom cabinet of apparatus US Time Zones Pacific Es PST Mountain MST Canadian Time Zones tao Hewgen e Brownsuile Ecology Help protect the environment we recommend that you dispose of used batteries by putting them into specially designed receptacles Maintenance Clean the unit with a soft cloth or a damp chamois leather Never use solvents IMPORTADOR Comercializadora Thomson de M xico S A de C V Alvaro Obregon No 151 Piso 13 Col Roma Delegaci n Cuauht moc C P 06700 M xico D F Telefono 52 55 11 020360 RFC CTM 980723 KS5 EXPORTER Thomson Inc P O Box 1976 Indianapolis IN 46206 1976 2006 Thomson Inc Trademark s Registered Marque s Depos e s Marca s Registrada s www rca com Printed in China Impreso en China Ehatiezton Baton acksonvile Hon Central CST EST Pacific PST Indoor Temperature The main unit has an internal thermometer that shows the current room temperature at the lower left of the display indicated by IN Outdoor Temperature A separate digital thermometer is included which can remotely tr
15. only ZA available when o WAKE1 WAKE2 is at the lock om position 2 To check the remaining duration before the radio turns off press and hold SLEEP 3 To cancel the sleep function press SNOOZE or OFF SW Tips You may also set sleep mode a to auxiliary audio source Connect the auxiliary source e g mp3 player and press RADIO AUX twice to select AUX mode after sleep time is set However the auxiliary source cannot be turned off by the unit For Your Safety The AC power plug is polarized one blade is wider than the ucr other and only fits into AC power outlets one way If the ar 8 plug will not go into the outlet completely turn the plug over and try to insert it the other way If it still does not fit contact a qualified electrician to change the outlet or use a different one Do not attempt to bypass this safety feature For Your Records In the event that service should be required you may need the model number In the space below record the date and place of purchase Date of Purchase Place of Purchase Service Information This product should be serviced only by those specially trained in appropriate servicing techniques For instructions on how to obtain service refer to the warranty included in this Guide Technical Information Product Clock Radio Brand RCA Model RP5440 Electrical Consumption Power Supply 120V 60Hz Power Consumption 4 Watts
16. r rate when you press and hold the buttons The between hour and minute time flashes when you are setting the time 3 Slide the switch o IWAKE1 WAKE2 on the top of the unit to o position when finished Selecting Wake Source You may be woken up by radio or alarm 1 Select an AM or FM station see directions on Radio 2 Set a wake time see above directions 3 Press WAKE 4 OFF1o0r2 repeatedly on the top of the unit to select a waking mode Corresponding icon lights on the front of the unit Wake 1 by alarm Wake 1 by radio A Wake 2 by alarm Wake 2 by radio Checking Wake Time Slide the switchOm WAKE1 WAKE2 on the top of the unit to WAKE 1 or WAKE 2 position to check the currently set wake time Limited Warranty United States What your warranty covers e Defects in materials or workmanship For how long after your purchase e One year from date of purchase The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm whichever comes first What we will do Provide you with a new or at our option a refurbished unit The exchange unit is under warranty for the remainder of the original product s warranty period Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product is within the warranty period must be presented to obtain warranty service For rental firms proof of fir
17. st rental is also required How to make a warranty claim Properly pack your unit Include any cables etc which were originally provided with the product We recommend using the original carton and packing materials Include evidence of purchase date such as the bill of sale Also print your name and address and a description of the defect Send via standard UPS or its equivalent to Thomson Inc Product Exchange Center 11721 B Alameda Avenue Socorro Texas 79927 Insure your shipment for of loss or damage Thomson accepts no liability in case of damage or loss en route to Thomson Pay any charges billed to you by the Exchange Center for service not covered by the warranty e Anew or refurbished unit will be shipped to you freight prepaid What your warranty does not cover e Customer instruction Your Owner s Manual provides information regarding operating Instructions and user controls For additional information ask your dealer e Installation and set up service adjustments e Batteries Damage from misuse or neglect Products which have been modified or Turning Off the Wake Alarm or Radio Press SNOOZE on the top of the unit The wake alarm or radio will be switched off temporarily The alarm or radio will be on again when the snooze period is over see SmartSnooze Operation To turn off the wake alarm or radio completely press OFF The wake alarm or radio will activate again the next day unless you switc
Download Pdf Manuals
Related Search