Mini HVLP Paint Spray Gun
Contents
1. Clean paint passages fully before disassembly Remove the fluid nozzle after removing the fluid needle set or while keeping fluid needle pulled in order to protect seat section While keeping fluid needle set inserted tighten fluid needle packing set by hand Then tighten gradually with a wrench Adjust the packing set while pulling the trigger and watching the movement of the fluid needle set since over tightening will strip the thread causing leakage Turn the spread adjustment knob counterclockwise to fully open it then tighten the spread adjustment guide into the gun body Pa i AA BR Ta 11 34 3 15 z tao i r fi ee En ae te 31 er ft Sg NN a a og TP ii mn e el aq 4 IL 14 5 IK LT i J if e 30 IL a 31 1 1 i Ng ek me A F EET j F 3 ry h je BI a i _o Meri T Eau A caL i y k y er a i om Co Fi Fi ka lan oan War Nae Nas laa L ie aj ae n Th an a NIS E N i SE n A Parts List S0 SIA USU Pb N N ee e le GA O Oo pANIDA UH PR 0 Fluid adjustment screw Fluid adjustment knob O ring Washer O ring Washer Switch spring Air inlet valve assembly Switch knob Switch washer Lock screw Nut Air cap washer Atomization Nut housing Fluid nozzle Fluid nozzle washer Bolt Compressed spring Needle washer Trigger level I 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 Trigger level II Tri2. gger Snap retainer Snap retainer Container cover Container Filter Fluid inlet joint Fluid needle Fluid needle spring Joint Paint adjustment knob Screw Paint adjustment joint Pattern adjustment screw O ring O ring Snap retainer Pattern adjustment knob O ring Air inlet joint Troubleshooting Symptom Intermittent spray Pattern arched Uneven pattern The center of the pattern is too narrow Poor atomization Spray concentrated into the centre Little to no paint output e Presence of air in the paint circuit e Material residue in the holes obstructs the pas sage of material e The nozzle is dirty or malfunctioning e The atomization cap is dirty or damaged e Material builds up on the outside of fluid nozzle tip or center hole or partially clogged nozzle orifice e Loose fluid nozzle e Atomization of air pressure is too high e Material too thin e The flow of paint is greater than the pressure and quantity of air supplied e Fluid passage is clogged with dirt e Air holes in the cover are blocked e Fluid needle stroke is too short Solution e Tighten the nozzle using the wrench provided e Make sure that the tank is not empty e Check that the connecting hole is not obstructed e Tighten the gland screw or replace the gasket if worn e Submerge the head in solvent e Clean and open all closed holes with a jet of compressed air or a toothpick e Do no
3. ker Mini HVLP Paint Soray Gun User Manual Technical Specifications e Model 8059851 e Air pressure 30 80 PSI e Nozzle diameter 1 4 mm e Type of feed Gravity e Air consumption 5 CFM e Pattern width 7 1 2 190 mm e Paint capacity 3 5 oz e aS i Coating eee at A al te lidt this a Coating should be N even and wet when spraying r t Release End of trigger stroke at this ni int PR poe E j 2 A Hf start am An f 19 Incorrect Correct method Hi method stroke trigger Operation 1 Suggested air pressure is 30 80 PSI 2 Recommended paint viscosity differs according to paint properties and painting conditions 3 Use the lowest possible fluid output that produces an adeguate paint coverage Finer atomization leads to a better finish Maintain a distance of 6 8 from the gun to the workpiece 5 The gun should be held so that it is perpendicular to the surface of the workpiece at all times Move the gun in a straight and horizontal line Arcing the gun results in an uneven paint finish T Maintenance 1 Ww N Pour remaining paint into another container and then clean paint passage and air cap Spray a small amount of thinner to clean paint passages Incomplete cleaning will cause adverse pattern shapes and particles to appear on your work Promptly clean components after use Clean other sections with a brush and cloth soaked with thinner
4. t use pointed metal objects or you may deform the hole of the head part e Clean the head and the nozzle e Make sure that the centering between the two is precise e Check that the tip of the pin is not ruined e Replace the nozzle and the head e Reduce the quantity of air and increase the flow of paint e Clean the head and the nozzle e Make sure that the paint is not too dense and dilute if necessary e Remove obstructions e Adjust fluid needle stroke
Download Pdf Manuals
Related Search